Search Documents

By Kenneth A. Pietila

The thickening and dewatering characteristics of refuse slurries are as variable as the coal mining operations and preparation plants that create them. This paper discusses these characteristics based on field studies at a number of mine sites. The connection between bench and full scale performance is confirmed with the design, construction and operation of an integrated 18m (60 ft) diameter thickener and 2.5 meter belt filter press system in Western Kentucky. The data from this system are presented.

Jan 1, 1984

By T. W. Beck, J. A. Organiscak

The U.S. National Institute for Occupational Safety and Health (NIOSH) Office of Mine Safety and Health Research (OMSHR) has recently studied several redirected scrubber discharge configurations in its full-scale continuous miner gallery for both dust and gas control when using an exhaust face ventilation system. Dust and gas measurements around the continuous mining machine in the laboratory showed that the conventional scrubber discharge directed outby the face with a 12.2-m (40-ft) exhaust curtain setback appeared to be one of the better configurations for controlling dust and gas. Redirecting all the air toward the face equally up both sides of the machine increased the dust and gas concentrations around the machine. When all of the air was redirected toward the face on the off-curtain side of the machine, gas accumulations tended to be reduced at the face, at the expense of increased dust levels in the return and on the curtain side of the mining machine. A 6.1-m (20-ft) exhaust curtain setback without the scrubber operating resulted in the lowest dust levels around the continuous mining machine, but this configuration resulted in some of the highest levels of dust in the return and gas on the off-curtain side of the mining face. Two field studies showed some similarities to the laboratory findings, with elevated dust levels at the rear corners of the continuous miner when all of the scrubber exhaust was redirected toward the face either up the off-tubing side or equally up both sides of the mining machine.

Jan 1, 2013

By W. S. Sanner

Experiments were conducted to determine the quantity and purity of ultraclean anthracite that could be prepared in the laboratory, using conventional separating techniques. A low-, a medium-, and a high-volatile anthracite were studied. Specific gravity separation followed by grinding, screening, and refloating at lighter specific gravities yielded small quantities of material purified to 1.0 percent ash, as follows: From low-volatile anthracite, 0.7 percent; from medium-volatile coal, 1.0 percent; and from high-volatile coal, 2.3 percent. The reduction in ash had no appreciable effect on the volatile matter or sulfur content of the coal. The limited quantities of material containing 1.0 percent or less ash obtainable indicate that if ultraclean coal is desired, a practical approach should include the processing units as an integral part of a conventional dense-media washing plant.

Jan 1, 1968

By L. V. Wade

The use of longwall/shortwall mining systems is under increasing scrutiny by the U. S, coal industry as a means to reverse the decline in productivity. The success of these mining systems depends to a great extent upon designing the system hardware to best suit local conditions. Of particular importance in this regard is designing the various elements of the total ground support system, including face, face end, and gate road supports, to accommodate local geologic conditions. This presentation centers on the problem of selecting the face support system. The existing geologic situation can influence the selection of the face support hardware in a variety' of ways. In general terms, these influences can be grouped into the following four areas: 1. The capacities required of the support unit; 2. The roof, coverage supplied by the support units; 3. The flexibility required of the support unit to meet changing geologic conditions; and 4. The required stiffness characteristics of the individual support units both vertically and horizontally. The following will center on the first area, i.e., the required d capacities of the support unit, in particular, the maximum required load density for a particular geologic situation.

Jan 1, 1976

By Ernest Hucke

This paper will cover basic pneumatic and electronic sensors, transducers, transmitters and their application in the Mining Industry.

Jan 1, 1965

By J. R. Brett

Utah Development Company (UDC) operates five large opencut coal mines in the Bowen Basin of Central Queensland, Australia. In total, over 20 million tonnes of coking coal are exported annually from the five mines. Typically, the coal seams dip at 5 percent, are 2 to 10 metres thick, and sub-crop some 20 to 40 metres below surface. In the main, the operations are single seam, but multiseam (2, 3 or 4 seams) operations do exist and will form an increasing proportion of the mining activities as depths increase. Draglines are used as the major stripping equipment, highwall depths currently ranging from 20 to 65 metres. Whilst project feasibilities were based on stripping to a 60 metre highwall, it is now proposed to continue opencut mining to depths exceeding 100 metres. This will entail large quantities of prestripping (ahead of the draglines) and overcoming problems associated with steepening seam dips, including haulage of coal from the pits.

Jan 1, 1982

By J. C. Mullen

Today, the coal mining industry is more knowledgeable on the potential negative economic consequences associated with improper management of hazardous substances and various types of solid waste. The practices evaluated during environ-mental audits are discussed and example situations are shared from previous audits of coal mines and analogous situations. The importance of assessing and understanding purchasing, warehousing, safety, maintenance, electrical, operations, and environmental management practices and procedures is highlighted as a key to a successful and practical program. A waste minimization approach is presented including strategies for screening product purchases, product substitutions, and testing and record keeping.

Jan 1, 1992

By Jack V. Hill

A unique type of grinding mill liner has been developed by Waagner-Biro A.G. of Austria. This liner system, termed an angular spiral lining (.ESL), was, successfully tested by Magma Copper Company's San Manuel concentrator in both their 10 Ft x 10 Ft (3.05m x 3.05m) and 12 Ft, 6 In x 14 Ft (3.81m x 4.27m) grate discharge wet grinding ball mills. Magma Copper's savings in power and grinding balls justified conversion of more than half of their twenty-six ball mills to the ESL system.1,2 The ASL system was provided by the Capitol Castings Division of Midland Ross Corporation, the exclusive licensee for such conversions. Capitol Castings proposed the following as expected benefits from installation of an ASL system in an 18 Ft x 21 Ft (5.49m x 6.40m) overflow discharge wet grinding ball mill at the Pinto Valley Operation of Cities Service Company: "(a) Reduction of power consumption per ton of ore milled = 12%, (b) Increased throughput = 6%, (c) Reduction of ball consumption = 6%."

Jan 1, 1982

By J. M. Goris

The U.S. Bureau of Mines, in cooperation with the Homestake Mining Co., and the University of Utah, is conducting a field demonstration to evaluate the behavior of rock masses supported with cable bolts. One of two rock masses being studied is supported with both conventional and birdcage cables. This rock mass is located between the 6500 and 6650 levels of the 45-4BN stope. 21 ledge. The second rock mass is the hanging wall of the D-limb stope between the 3500 and 3650 levels near the Ross Shaft and is supported with conventional cables. The primary objectives of the project are to monitor the behavior of the two rock masses during mining using extensometers and cable support strain gauges, after which the rock will be modeled using the finite-element code UTAH III. Field data will be used to verify the modeling. In addition. a comparison between the effectiveness of conventional and birdcage cables will be made.

Jan 1, 1991

By M. J. Laurila

On-line analyzers have made possible the use of Fuzzy Logic Control (FLC) for local control applications in coal preparation plants. This includes FLC control of complete circuits such as heavy media vessels, cyclones and froth flotation. These circuits can be controlled in real time in a feedback control loop with an on-line analyzer. Control strategies can be readily developed using Statistical Process Control (SPC) techniques which are first applied off-line in manual mode through the use of control charts and then this process is brought on-line using FLC in conjunction with an on-line analyzer to fully automate the circuit. This paper outlines the types of control strategies employed and presents examples of automatic verses manual control.

Jan 1, 1997

By C. P. Lazzara, R. W. Pro, A. C. Smith

The U.S. Bureau of Mines conducted a study to evaluate the effectiveness of automatic water sprinkler systems in the extinguishment of incipient conveyor belt fires under ventilated conditions. Large-scale experiments were conducted using a double strand conveyor belt configuration. Standard response, pendent-type sprinklers, with activation temperatures of 100°C, were installed above and between the two strands of belting, in accordance with Federal standards for sprinkler system installations in belt drive areas. Experiments at airflows of 1.1 and 4.6 m/s showed that the sprinklers activated later, the peak heat release rate was larger, and more betting was consumed at the higher airflow. In experiments with 74°C, fast response, directional sprinklers, the sprinklers activated at the same heat release rate for both high and low airflows, but the peak heat release rate and amount of bett consumed was slightly higher at the lower airflow. Experiments were also conducted with 100 °C, standard pendent sprinklers installed above the top belt, in accordance with the National Fire Protection Association (NFPA) Standard 123 for sprinkler system installations in conveyor belt drive areas in underground coal mines. In these experiments, the heat release rate and amount of betting consumed was larger at the higher airflow.

Jan 1, 1995

By J. J. Moore

Combustion synthesis or self propagating high temperature synthesis (SHS) reaction systems are discussed with respect to thermodynamics and kinetics. In particular, tile effect of the process parameters, ego particle size, AHf, ignition and combustion temperatures on these self sustaining reactions is discussed. Combustion theory is used to investigate the effect of the overall activation energy of the SHS reaction on the combustion front propagation rate and in obtaining a clearer understanding of the transition from stable to unstable propagation. Finally, examples of the application of combustion synthesis to advanced materials processes are made, in particular the synthesis of Ni-Ti -X intermetallic shape memory alloys, TiC-Al2O3 and ZrB2 ?Al2O3 ceramic composite materials.

Jan 1, 1991

Ferric (Fe3+) ions are omnipresent in flotation circuits. Depending on pH and the nature of the ore body, Fe3+ ions may play a role in the adsorption of thiol collectors on sulfide minerals. To investigate this possibility, a two-compartment galvanic coupling cell was designed. This cell was used to monitor changes in contact angle of a sulfide mineral in one compartment, while varying concentrations of the Fe3+ ions in the other. The results showed that Fe3+ ions promote xanthate adsorption as indicated by the increase in contact angle. Implications of this finding in sulfide mineral flotation in general will be discussed.

Jan 1, 1998

By M. A. Anderson

After mope than fifty years Of Continuous operation, the Nevada Mines Division found itself faced with declining ore headings and metallurgical efficiencies, and rising operating costs. Although intensive process improvement programs had been initiated at various times in its history, insufficient return on investment served to defeat plans for any major changes in circuitry. The advent of practical large-volume flotation machinery, along with the success of long-range exploration drilling programs, complimented the results of an intensive program of research and development. The result of laboratory testing, pilot plant testing, and full scale plant tests was the proven indication of metallurgical improvement given increased flotation residence time and the effect of mechanical agitation in flotation.

Jan 1, 1975

By M. R. Shahan, W. R. Reed, J. P. Rider

Roof bolter operators may be exposed to high respirable dust concentrations on continuous miner sections with blowing face ventilation when bolting is performed downwind of the continuous miner. One solution to reduce the high respirable dust concentrations is to use a canopy air curtain (CAC) to deliver clean air from a filtered blower fan directly to the bolter operators under the canopies. The influence of CAC installation in the airflow and dust dispersion around the location of the roof bolter operator can be evaluated by using computational fluid dynamics (CFD). This study, performed by the National Institute for Occupational Safety and Health (NIOSH), considers two scenarios: (1) a roof bolting machine in the center of the entry for installation of the fifth row of bolts from the face, and (2) a roof bolting machine positioned close to the face for the installation of the last row of bolts. In both scenarios, the bolting machine is placed in an environment which contains 6.0 mg/m3 of respirable dust and is ventilated by a blowing curtain with 3000 cfm (1.42 m3 /s) of air. This environment is used to simulate the roof bolter machine operating downstream of a continuous mining machine. Two operation positions are simulated at the same bolting location: dual drill heads in the inward position for two inside bolts and dual drill heads in the outward position for two outside bolts. The influence of the CAC on airflows and dust dispersion is evaluated with the CAC operating at 250 cfm (0.12 m3 /s).

By C. Dale Elifrits

Observations made from laboratory analysis of samples of fine-grained argillaceous materials (shales) subjected to various changes in moisture content have been correlated to loss of strength in the rock material. This reaction to a change in in-situ conditions (subsequent to mining) at a mine site combined with the observed relationships of surface-disturbing subsidence features at locations where the predominant overburden material is fine-grained, provides a predictive tool for the subsidence engineer.

Jan 1, 1983

By Daniel Amponsah-Berko, Palas Kamlakar Borkar, Kwabena Boafo, Neha Sharma, Timothy Eisele

A series of iron-leaching experiments were conducted to test the ability of metal-reducing anaerobic organisms to reduce iron from Fe3+ to Fe2+ to dissolve it from iron ore tailings. This bioleaching process involves the fermentation of biomass from Typha latifolia (a common wetland plant) to generate organic compounds, which, along with metal-reducing organisms, reduce and dissolve iron. The concentration of dissolved iron over time was studied for one year. Iron concentration above 1150 mg/L was achieved at a pH range of 3.95–5.36. Tailings from multiple locations were examined.

Feb 1, 2025

By Javad Sattarvand, Amin Moniri-Morad

Predicting equipment failure behavior plays a critical role in providing a safe operation. Although various reliability evaluation methods are available for estimating failure behavior profiles, these approaches are based on mathematical formulation, leading to actual operation simplification and improper estimation of failure trends. This study proposes a discrete-event simulation (DES) approach to model fleet failure behavior. This approach can model the maintenance strategies in multi-component systems with minimum simplifications. In this regard, the first step was to collect a historical failure time dataset (e.g., the time between failures). Then, the DES model is established to predict the severity of failure events and design maintenance strategy considering actual operation circumstances. Afterward, the maintainability analysis was performed to estimate equipment downtime and availability. The achieved results showed that the system availability was about 85%. Also, the findings demonstrated that the DES could efficiently predict the equipment failure behavior using various stochastic events.

Jun 25, 2023

By T. W. Meikle

Three nutrient amendments and a biological seed inoculant were evaluated for use in establishing vegetative cover on waste rock substrates. Randomized blocks were placed on three substrates. Treatments included two types of organic fertilizer, mineral fertilizer, Azospirillum bacterial inoculant, plus controls. The seed mix consisted of native grass species adapted to low nutrient conditions. Canopy cover has been monitored for three growing seasons. Results indicate: 1) two of three substrates support plant growth following amendment with organic fertilizers; 2) organic fertilizers increase cover substantially over mineral fertilizer; and 3) Azospirillum had no effect on canopy cover.

Jan 1, 1999

By Erik A. Munroe, Nelia W. Dunbar, Virginia T. McLemore

In New Mexico, there are at least 100,000 abandoned mine waste rock piles with widely ranging geochemical and mineralogical compositions. A geochemical and mineralogical study was implemented for five waste rock piles, some which contained sulfides, in the Hillsborn Mining District. Chemical and physical characteristics of mineral grains and their secondary mineral oxidation rinds were examined with the electron microprobe. Pyrite and chalcopyrite appear to be the most reactive to oxidizing conditions. Clays, iron oxide, iron hydroxide, iron sulfate, and primary texture rinds exist in the waste rock piles analyzed.

Jan 1, 2000