Search Documents

By Harry E. LeGrand

The purpose of this paper is to outline briefly some basic principles of ground-water hydrology that have application in mine hydrology and to suggest that an understanding of these principles can help to forestall problems that are internal as regards mining operations and external as regards damage or harm to surrounding areas. The development of a mine below the water table pleads for accurate values to answers of hydrologic problems. Such internal problems involve both an inflow of water without adequate drainage facilities and a deficiency of water for the required mining or milling use. Methods which give acceptable quantitative values for the solution of many ground-water problems depend on rather simple geologic structures, characterized chiefly by homogeneous rocks of considerable areal extent. Unfortunately, mining operations are likely to be centered where rocks are not homogeneous. Consequently, methods that attempt to show values of the storage and transmitting capacity of rocks in mining areas must be applied with caution. In spite of complex geology and apparent uniqueness of individual mines and quarries, adherence to some concepts of ground-water occurrence and movement should be helpful to mine operators. Mining operations that extend below the water table disturb the natural hydrologic regimen. Prior to development, the water table slopes away from the site of a mine in at least one direction, but as soon as development begins and water is removed from the mine, the mine becomes the apex of a depressed cone in the water table, causing a convergence in the flow of water toward the mine, The behavior of the cone of depression, as it tends to deepen and to increase in areal extent when the mine is deepened, is related to the rate of withdrawal of water necessary to keep the mine dry. The significance and nature of the cone of depression in the vicinity of pumped wells has been studied by ground-water hydrologists for years, but the cone caused by pumping water from mines has generally been less systematically appraised. The geologic and hydrologic settings of mines range greatly so that a simple standard procedure for dealing with problems

Jan 1, 1972

By Juan J. Monsalve, AMAN SONI, Nino Ripepi, Richard Bishop

The design and strength of pillars are important parameters while implementing the room-and-pillar mining method in a limestone mine. The process becomes complex with the presence of the karst voids which are frequent phenomena in a carbonate rock formation. The karst system is a network of cavities that along with an omnipresent fracture network may lead to ground control issues in a limestone mine. The objective of this study is to provide a safe and reliable alternative design for a pillar in a case study mine for safe and efficient ore recovery. This research is a continuation of a previous study aimed at studying the effect of karst void on the strength of the same limestone pillar. It was assessed from the calculated pillar strength and the estimated redistributed stresses that the pillar is capable of countering more stress than is currently imparted on it. Numerical modeling studies combining in situ stress determination and excavation sequencing were used to estimate the existing stresses on the pillar. Different possibilities of modification to existing pillar design were simulated using Distinct-Element Modeling (DEM) to determine a better design. Discrete fracture networks (DFNs) were included to imitate the effect of the presence of discontinuities. An effort is also made to understand the variation of pillar strength with height for karst-affected pillars using two different constitutive models. This study serves as a preliminary investigation in terms of improving the future design of pillars and also while recovering old pillars prone to karst formation.

Jan 30, 2023

By M. L. Bricker

The Jim Bridger Mine is operated by Bridger Coal Company and is located in Sweetwater County, 35 miles (56 km) northeast of Rock Springs, Wyoming (USA). The general location of the mine site is shown on Figure 1. Bridger Coal is a joint venture of NERCO Coal Corp, the operator, and Idaho Energy Resources Company. The permit boundary encompasses in excess of 20,000 acres (81 km2) and is nestled against the western side of the Continental Divide. Production started on July 3, 1974, and the mine has produced approximately 90 million tons (82 million t) while moving approximately 450 million cubic yards (344 million m3) of virgin earth. Annual production averages 5 to 7 million tons (4.5 to 6.4 million t) of run-of-mine coal. Coal is consumed on site by the Jim Bridger Power Plant, a 2,000-megawatt generating station, and the electricity is transmitted to the Pacific Northwest power grid (Oregon, Idaho, Northern California, etc.).

Jan 1, 1991

By III Basham

As environmental laws and regulations become more complex and the economic cost of non-compliance becomes greater, periodic assessment of environmental compliance, identification of potential liability and implementation of any necessary remedial action should be a standard part of the operational methods of any successful business. The title of this paper "Environmental Audits, A Shield, A Sword or A Trojan Horse?" is intended to draw attention to the fact that environmental audits can be used positively to shield a business operations from actual or potential environmental liability; can be used proactively as a 'sword" in both a marketing context ("do business with us because we conduct our business safely and professionally?) and as a mechanism for developing positive relationships with environmental regulators; and, used negatively, as a "Trojan horse", by developing information which those same environmental regulators (or the public) use in an enforcement context against your business or that of your clients. This paper will discuss the concept of environmental audits in general; the pros and cons of conducting the same; and the role of the attorney, as part of the "audit" team, to insure, to the greatest extent possible, that the audit process is productive from both a managerial and legal perspective.

Jan 1, 1992

By H. M. Park

Risk is a major factor in all mining activities, arising from many internal and external variables. The authors? research has resulted in a systematic method for the quantification of risk in mining projects (Park, 2012). This research will be presented in a series of papers, this one and two more that will be published on Mining Engineering?s web site, www.me.smenet.com. This paper identifies the variables associated with risk in mining projects, and their effects. The second paper discusses methods of assessing the overall risk associated with those variables, and presents a statistical model based on a survey of 31 experts. The third paper presents an evaluation of the statistical model, using data from previous mining investment decisions in which the authors have been involved. There are several major competing entities, including BHP Billiton, Rio Tinto, Anglo American, Xstrata, Freeport-McMoRan, Chinese government- run companies and Japanese trading companies, that have large foreign holdings, controlling deposits in most of the world?s established and productive mining districts. In general, the mining industry considers the United States, Canada, Australia and the European countries to have good mining investment environments, but because the major companies have already achieved market dominance in those countries, large investments are required there. Newcomers seeking to enter the industry, either as producing companies or as investing partners, often have difficulty breaking into these established markets. Thus newcomers are increasingly turning to new areas like South America and Africa, which are relatively less developed. The competition among businesses to secure a share of the new market is intense, but there are still good investment opportunities. However, because most of the countries in these areas are not well developed, several additional risks are associated with participation in mining projects in those areas.

Oct 1, 2013

A conventional paddle-type mixer and a gravity flow mixing device were evaluated for conditioning of phosphate ore with fatty acid and fuel oil, and for acid scrubbing prior to cationic flotation. Gravity flow mixing required less residence-time, but slightly higher reagent concentrations to achieve recovery levels similar to conventional conditioning. Grade was less sensitive to reagent concentration using the gravity flow mixer. For acid scrubbing, the gravity flow mixer proved equally effective. In this paper, the effect of time, pulp density, reagent concentration, and emulsification on conditioning and acid scrubbing efficiency of the two devices will be discussed.

Jan 1, 1987

By K. L. Purdy

Electron spectroscopy for chemical analysis (ESCA) was used to determine the-surface characteristics of products from operating Pb-Zn-Cu concentrators on the New Lead Belt of southeast Missouri and pure galena and sphalerite samples treated-with flotation reagents in concentrations similar to those used in the mills. The emphasis was on the action of surface modifiers such as Na2Cr207, starch, SO2, CuSO4 and NaCN in sphalerite flotation and in the galena-chalcopyrite separation. The objective of the investigation was to monitor the relative oxidation states of the mineral and reagent constituents and correlate these surface concentrations and oxidation states with flotation theory and practice. ESCA was able to follow the action of all the modifiers except NaCN. The existence of PbCrO4 on the surface of galena conditioned with Na2Cr207 was verified. The Pb in the bulk PbS-CuFeS2 scavenger concentrate was found to be significantly more oxidized than the Pb in the bulk PbS-CuFeS2 rougher concentrate. ESCA was found to be most useful for investigating the actions of modifiers rather than collectors due to the large amounts of sulfur and background carbon already present on the mineral surfaces. After calibration for the particular chemical system of interest, ESCA can yield semi-quantitative analyses of the oxidation states of many elements (except hydrogen, and helium) present in the outer 10 to 25 A of a sulfide mineral surface.

Jan 1, 1975

By R. D. Hagni

Pyrometallurgical products from lime roasting of refractory gold ores, pyrite, and arsenopyrite have been examined for their mineralogy, porosity, permeability, retention of contaminant sulfur and arsenic, and potential effectiveness of gold extraction. Cathodoluminescence microscopy, supplemented by X-ray diffraction and scanning electron microscopy-energy dispersive analysis study, has shown that the products phases have characteristic cathodoluminescence properties as follows: anhydrite (CaS04), deep blue; unreacted portlandite (Ca(OH)2), deep purple; oldhamite (CaS), light yellow to rarely pink or orange; a sulfur-rich, arsenic-poor phase, violet; an arsenic-rich, sulfur-poor phase, non-CL. Within the temperature range examined (400-850°C), hematite exhibits greater porosity and permeability at the intermediate roast temperatures of 600-650°C.

Jan 1, 1993

By R. M. Campoy

Mexico's mineral wealth has long been recognised and indeed has played a historically significant role on a world scale. The dynamics of the Mexican mineral industry have experienced a dramatic transformation especially over the last two decades. This transformation has mainly been instigated by the high growth rates and industrialisation of the Mexican economy since the 1960's. This paper focuses on the base metals sector of the industry which represents one of the major contributors to this transformation. The objective is to present a brief base metals review and to discuss some recent occurrences which pertain to this sector of the industry. This is followed by a discussion of mining's relevance in the current economic situation in Mexico. With this overview as background, the investment climate, primarily from a domestic investor's perspective and secondly in terms of foreign investment, is discussed. Finally, some recent government initiatives, including tax and accounting changes, are outlined. Any one of the sections of this paper can easily be developed into an extensive and indepth analysis; however, the intention of this paper is to provide the reader with a broad overview of the topics discussed.

Jan 1, 1985

By Ernest Y. Baafi

The technique of linear kriging as a grade estimation method of mining blocks is reasonably established in the mining industry. Because of the nonbias condition imposed in kriging which requires that the kriging weights (?i) add up to one, negative weights are sometimes used in kriging. The use of negative weights is not justifiable from the practical standpoint. Also, negative block grades can be obtained in some extreme situations which makes no practical sense. To guarantee non-negative weights an additional constraint is required in the kriging system of equations. Unfortunately, the nonnegative weight constraint results in a set of non- linear system of equations. In this paper, a derivation of the resulting set of nonlinear equations is presented and a numerical algorithm is developed for the solution of the equations. Because the algorithm developed does not remove negative weights arbitrarily, optimal nonnegative weights are always guaranteed. Results obtained using the developed algorithm were compared with those using the standard linear kriging, in terms of computer time and the estimation results. Both the computer time and the kriging variance were found to be higher with nonnegative constraint, as expected. However, some systematic pattern was observed in the kriged values (i.e., over or under estimation) with or without the nonnegative constraint. The study also demonstrated when one should generally expect negative kriging weights in practice, and what practical impact the negative weights can have on the kriging estimates.

Jan 1, 1984

By J. Drelich

The adsorption of oleate at the surface of titanium dioxide from aqueous solutions was examined by Fourier transform infrared (FT -IR.) spectroscopy using a germanium internal reflection element coated with a thin film of TiO2. This thin film, with a thickness of 100-200 A, was deposited on the surface of a germanium single crystal by RFIDC magnetron reactive sputtering. It was found that significant adsorption of oleate from a 0.02-0.03 mM aqueous solution on the surface of TiO2 thin film occurs at neutral pH, from about pH=5.5 to pH=7.7. Adsorption of oleate at the surface of the amorphous TiO2 thin film appeared to be reversible, involving soap-acid dimers.

Jan 1, 1997

By K. L. Lamb

At the Sierrita mine, 40 km (25 miles) south of Tucson, Arizona, Duval Corporation is rapidly gaining operating experience with its new Portable Crushing and Conveying System, (PCCS). As of November 23, 1983, over 4.5 million tons (5.0 million st) of ore have passed through the system. Mining cost per ton for the months of July, August and September was 83% below the average for the first five months of 1983. Although all the cost reductions experienced cannot be attributed to the Portable Crusher, it was a major contributing factor. The Sierrita ore deposit has several natural topographic and geologic conditions which are not favorable to mining. It is not a sidehill deposit and therefore no low-level exit points exist to facilitate truck haulage. The ore is very hard. Quartz diorite, hardest of the three major rock types, averages 172-207 MPa (25-30 000 psi) unconfined compressive strength and may run as high as 345 MPa (50 000 psi). Blasting in this rock produces oversize material which runs approximately 20% 51 centimeters (20 inches). The ore is low grade, averaging slightly better than .30% contained copper and .035% contained molybdenum, with small amounts of silver. These conditions, plus high design production tonnages, make the Portable Crushing and Conveying System (PCCS) practical for Sierrita. Without crushing and conveying, truck haulage would be prohibitively expensive. A typical, October, 1983, ore haul from the bottom of the pit would involve a vertical lift of 260 meters (850 ft) and a horizontal distance of 3 860 meters (12 200 ft) were not in-pit crushing and conveying available. The corresponding cycle time would be nearly 32 minutes.

Jan 1, 1984

By Thomas L. Craig

The Wellman-Lord SO2 Recovery Process is operating commercially at one location in this country and at two locations in Japan. Tail gases from a sulfuric acid plant, from an oil fired steam generator and from a sulfur recovery unit are the respective applications. 1) At the Olin Corporation's Paulsboro, New Jersey, stack gas from a spent acid regenerative sulfuric acid plant-45000 SCFM - is treated in the W-L unit to reduce sulfur dioxide concentrations from 4500 ppm to less than 500 ppm. 2) At the Japan Synthetic Rubber plant in Chiba Prefecture, stack gas from an oil-fired steam generating plant - 120,000 SUM - is reduced from 2100 ppm S02 to less than 200 ppm. 3) At the Toa Nenryo Kogyo refinery in Kanagawa Prefecture, tail gas from a sulfur recovery (Claus) unit - 41,000 SUM - with, an inlet SO2 concentration of up to 13000 ppm is reduced to less than 200 ppm. The three installations are operating successfully and are capable of reducing S02 emissions to levels significantly below the concentration guaranteed. With the one exception of a higher than guaranteed chemical make up requirement at Paulsboro, utility and chemical requirements will be less than design.

Jan 1, 1971

By Yinan Zhang, Yi Luo

The widely used R70 method is modified to measure the self-heating propensity of low-rank coals. This modified R70 method enables the introduction of controlled amount of moist oxygen into the reaction vessel. Three coal lumps were collected from three different locations in a surface mine in the Powder River Basin. The coal samples were tested in oxygen flow with controlled moisture content under adiabatic condition. By measuring the relative humidity at the exhaust exit point of the testing setup, the flux and cumulative wetting heat that is consumed by coal samples can be determined. Through a better way of determining the coal’s specific heat, the total heat, including heat of wetting and coal’s oxidation heat, required to raise coal to a given temperature can be determined. Then, the contribution of heat of wetting at the different stages of the testing is quantified. The effects of evaporative heat through a group of tests have also been quantified. From this research, a better understanding of the effect of wetting heat on inducing low-rank coal’s spontaneous combustion can be acquired.

Nov 30, 2022

By C. Zhou, R. Jacksha

This paper reports measurement results for radio frequency (RF) propagation around 90° corners in tunnels and underground mines, for vertically, horizontally and longitudinally polarized signals. Measurements of signal power attenuation from a main entry into a crosscut were performed at four frequencies — 455, 915, 2450 and 5800 MHz — that are common to underground radio communication systems. From the measurement data, signal power loss was determined as a function of signal coupling from the main entry into the crosscut. The resultant power loss data show there are many factors that contribute to power attenuation from a main entry into a crosscut, including frequency, antenna polarization and crosssectional entry dimensions.

Jan 1, 2016

By Slobodan Vujic, Goran Cirovic, Dragan Radojevic

Mine production systems (MPS) are characterized, more or less, by the following properties: uncertainty, subjectivity, impreciseness, polysemy, instability, indefiniteness and lack of data. From modern study aspect these MPS mathematically belong to the class of fuzzy systems. With this in mind, the usage of fuzzy sets is recommended as a methodology that treats impreciseness, indefiniteness and complexity of mine production systems in a satisfactory manner. Fuzzy modelling, discussed in this pa- per, is applied as a mathematical implement. The objective of the paper was to show production optimization in practice on the ex- ample of bauxite open pits where fuzzy linear programming (FLP) was used following the criterion per income. The variables in criterion function are linguistic variables while both variables and variable restrictions are presented by triangular fuzzy numbers (TFN). The term "satisfactory income" presented through triangle fuzzy numbers was introduced instead of "maximizing the income". sensitivity of the obtained solutions has been analysed

Jan 1, 1996

By Eduardo Rojas, Pedro Landeros

El Teniente Mine expansion plans are currently under development and construction stages through an integrated project strategy that will allow the continuity of future mining. The deepest sector corresponds to Andes Norte Project that faced rockburst risks during tunneling in a completely different manner, implementing different actions for the mitigation of seismic hazard and seismic risk management, based on the following main aspects: rock mass preconditioning techniques such as destress blasting and hydraulic fracturing, improvement of rock support design with the inclusion of elements with higher energy dissipation capacities, use of mechanized equipment for the most critical activities in addition to re-entry protocols and improvements in geological, geomechanical and seismic data collection procedures to reduce the uncertainty of rock mass behavior. The current seismic risk management strategy integrates all of these elements and is the basis of construction methodologies in use, supporting the technical feasibility of tunneling in high-stress environments.

Apr 26, 2022

By T. L. Carstensen

The Miami In-situ mine of BHP Copper is located in Globe-Miami, Arizona. The mine leaches mineralized leach capping over a supergene enriched sulfide deposit, and has produced over 500 million lbs of copper during the last 50 years. The Miami unit has identified several opportunities to enhance and expand in-situ production. A computer block model consisting of strict geologic controls, mineralogy, and metallurgical data was developed to assist in the determination of the leachable copper resource. An understanding of the accessibility and solubility of the resource to leaching solutions and the integration of hydrogeologic and hydrometallurgical information was necessary for completion of this project.

Jan 1, 1997

By Peter N. Blakey

The Kidd Creek orebody is a massive, base metal deposit with widths up to 600 feet and a strike length of 2,200 feet. The orebody dips eastwards at 70° to 80° and is amenable to sub-level open stoping. Five distinct zones (Fig.1) based on structural wall rocks and ore type parameters occur within the orebody. These zones are: Zone 1 - Mainly copper stringer ore Zone 2 - Massive pyrite ore Zone 3 - Massive sphalerite and chalcopyrite Zones 4 and 5 - Are banded and variable in nature Compressive strengths vary from zone to zone with an average of 22,000 p.s.i. and highs of 40,000 p.s.i. The mine is developed from a ramp extending from surface to the 1600 foot level and a 24 foot diameter, 3050 foot vertical shaft with main levels at 400 foot intervals. Sub-levels at 100 foot vertical intervals are driven from the ramp. transverse and longitudinal pillars to support the crown pillar left under the open pit. The layout allows an opportunity to enlarge or reduce pillar sizes and also to introduce fill on any horizon should conditions warrant. It also offers a large number of operating stopes spread through the various ore zones giving good ore blending characteristics. All ore from the stopes is handled through drawpoints using Wagner ST8 scooptrams with an average one way haul length of 650 feet.

Jan 1, 1976

By Felicia F. Peng

To minimize SO2 emission and the particulate problem during combustion of high sulfur coal fines is to agglomerate these fines in the presence of limestone. At subsequent combustion process, the sulfur in coal is oxidized and reacts with calcined limestone to form calcium sulfate in ash, while the base carbon is converted to clean energy. Seventy percent of sulfur retention can be achieved at Ca/S mole ratio of 3 at a temperature range of 500-400°C. The sulfur fixation in agglomerates involves the complex mass transfer and multiple successive reactions. The rate expressions have been developed to describe the progress of sulfur fixation in the agglomerates during combustion.

Jan 1, 1985