Search Documents

By P. R. Taylor

Batch leaching experiments have been performed to study the kinetics of galena leaching in fluosilicic acid solutions with oxidants. Variables studied included: fluosilicic acid concentration, oxidant type, oxidant concentration, particle size and leaching temperature. It was found that hydrogen peroxide was the most effective oxidant, compared to the others studied, and the effect of the oxidant concentration on the leaching behavior of galena was very significant. Also, decreasing the particle size and increasing the leaching temperature increased the extraction rate. The initial, apparent activation energy was calculated to be 11.72 kJ/mole (2.8 kcal/mole) and suggested that galena leaching in fluosilicic acid solution, with hydrogen peroxide as an oxidant, may be controlled by fluid film mass transfer initially. The reaction appears to be retarded by the formation of elemental sulfur and the sulfur oxidation becomes a major resistance to the overall leaching reaction.

Jan 1, 1992

By Arthur E. Lewis

A contained nuclear explosion is proposed to produce a chimney of broken ore well below the water table. After the chimney is filled with water and reaches hydrostatic equilibrium, oxygen, under pressure, is introduced near the bottom of the mass of broken rock. The increase in solubility of oxygen at high hydrostatic pressure is sufficient to initiate the oxidation of the primary sulfides: chalcopyrite and pyrite. The oxidation and dissolution of these sulfides produces enough heat to increase the temperature of the ore and water in the chimney as much as 1000 to 150°C. The rate of dissolution of chalcopyrite becomes so rapid under these conditions that the rate of recovery is no longer limited by the rate of chalcopyrite dissolution, but by the degree of exposure and other factors. Means of solution control and distribution of oxygen in the chimney have been examined in some detail. A calculational model utilizing experimentally determined solubility rates is utilized to estimate the temperature rise in the chimney and the rate of copper recovery as a function of initial temperature, sulfide content of ore, size of sulfide particles, and fraction of sulfide exposed to solution.

Jan 1, 1972

By German Zambrana

The solution of the problem of beneficiation of cassiterite from its primary ore deposits is of fundamental importance to Bolivia. The process today involves a gravimetric treatment of the ore followed by sulphide flotation. During the last year, a cassiterite flotation stage has been added in several plants to treat the slime tailings. Although cassiterite flotation is already economical for the slime tailings and the mechanism of the process are understood, it is felt that further research could improve the results. In the past, considerable amount of research and test ark has been performed to select appropriate collectors to improve recovery, to increa¬se the grade of tin in the concentrate, to minimize the effect of metallic ions like Ca+2, Fe+2 and Fe+3 which prevent flotation, and to increase the pH of the pulp which now it can not be higher than 3.0. It has been reported that the halogen salts (1) like NaCl exhibit special surface affinity for cassiterite but none for quartz. These effect seems to be favourable for the selective flotation of cassiterite from silica minerals. In view of these preliminary results it was decided to follow the research accordingly: OBJECTIVES The objectives of the present investigation are: 1. 0 evaluate the influence of NaCl salts in quartz and cassiterite flotation.

Jan 1, 1971

By N. Ripepi

"The Langmuir model has been widely used for the coal-methane sorption process via an isothermal test. However, even though the temperature-dependent Langmuir model were recognized theoretically and experimentally, the quantitative relationship between the Langmuir’s constants (a & b) and temperature have not been clarified and confirmed by lab test data. This paper collects 158 methane-coal sorption data under different temperatures, which apply the Langmuir model to consider the relationship between Langmuir’s constants (a & b) and temperature (see APPENDIX I). Even though the Langmuir model cannot be used to show the physical state of methane adsorption on coal, it is widely used because of its simplicity and the reasonable explanation of its parameters (a & b). The results from these published isothermal tests confirm that 1) there is no consistent relationship between Langmuir’s constant-a and temperature; 2) the Langmuir model is a temperature-dependent model, and the temperature-dependent feature is mainly shown by the relationship between Langmuir’s constant-b and temperature; 3) The relationship between Langmuir’s constant-b and temperature can be described by both the exponential and linear relationship with dried coal. This paper provides a database for temperature-dependent Langmuir’s model, which can be used for reservoir simulation of coalbed methane reservoir, coal seam degasification modeling for underground coal mines considering the heating effect induced by geotherm and heat injection (via hot water, hot steam, ultrasonic, etc.). INTRODUCTION The isothermal test for gas sorption on coal is one of the fundamental tests in Coalbed Methane (CBM) recovery fields, such as underground coal mine methane degasification, CBM gas-in-place estimation, and carbon dioxide sequestration in un-minable coal seams. Generally, two methods, volumetric and gravimetric, are employed to obtain isothermal data (Bush, A. & Gensterblum, Y., 2012). Based on these two approaches, a series of commercial and self-assembled instruments are built and several calculation methods are used to obtain isothermal data (Bush, A. & Gensterblum, Y., 2012, Gasparik, K., 2014; Goodman, A. L., et al, 2004; Zhang, L., et al, 2013). In the post-processing stage, many models are provided to analyze isothermal data in order to understand the storage mechanism of gas in coal. Common models include the Langmuir model (and its extended forms), the pore-filling model, multilayer adsorption model (BET), and the Gibbs’ model. Among these models, the Langmuir model is the most widely used for its simplicity and functionality. The Langmuir model is expressed as follows:"

Jan 1, 2016

By E. Hsieh

Proximity detection in the open pit mine can be used effectively as an operator assist strategy which improves digging production through enforcement of best practices, although it is normally thought of first as a safety tool, and second as a step toward full automation when combined with object avoidance.

Feb 23, 2014

The purpose of this talk is to report the answers to the-'two following questions: I. What unique services does the mining industry expect of mining and mineral processing engineers? II. What suggestions does industry offer to educators to help revamp curricula to meet the needs of a changing industry? As the result of many questionnaires filled out in person by presidents, managers, superintendents, chief engineers, metallurgists, and other responsible individuals in operations and management of large and small metal and nonmetallic mining companies in the U. S., and to some extent abroad, we now have some, specific answers to the above questions. Although answers to questionnaires continue to arrive at this writing (February 10) the volume already received is sufficient to clearly justify certain conclusions and observations. A copy of the tally of the first 117 questionnaires received accompanies this report, and I am certain that a compilation of additional questionnaire data will merely reinforce, the trends in thinking that have been' established thus far. Here are the results of the survey:

Jan 1, 1961

By W. Jack Wilkes, Gilbert L. Butler

TRANSPORTATION TUNNELING The use of tunnels for transportation, namely rapid rail transit systems and highways is on the increase. How much that increase might be through the 1980's is the question that is discussed in this paper. In 1975, there were 218 route miles of subway tunnels for rapid rail transit and 154 lane-miles of highway tunnel. From the viewpoint of many transportation planners and designers, the tunnel is one of the tools which may be used to by-pass many types of obstacles: a mountain, a body of water, or a Central Business District (CBD). Therefore, the transportation tunnel is a rural as well as an urban solution with major emphasis on the latter because of the current transportation needs of our cities. In the case of rural locations, tunnels are usually constructed through mountains in order to eliminate miles of steep grades and dangerous curves, such as the Eisenhower Tunnel which cuts through the Continental Divide in Colorado along 1-70 and saves 10 miles and 40 minutes of driving time. Tunnels also provide an excellent transportation link across bodies of water in order not to interfere with shipping lanes. The Chesapeake Bay Tunnel and Bay Tubes of the BART system are excellent examples of this type of tunnel.

Jan 1, 1976

By I. Chatterjee

The application of microwaves has a demonstrated potential for the ultimate removal of water from fine coal. The principle of microwave drying of fine coal is based on the selective absorption of microwaves by water. Coal is a poor absorber of microwaves. As a result, water can be removed from fine coal by selectively heating water molecules. One of the difficult problems drilling microwave heating is the exact determination of temperature in the core of the materials. The electromagnetic energy absorption in coal/water mixtures during microwave drying is controlled by several factors including the dielectric properties of the constituents. In this paper the dielectric properties of various ranks of coal are presented as a function of frequency and moisture content. The measured dielectric data are incorporated into electromagnetic and thermal models of coal which predict the energy absorption and temperature distribution during microwave heating.

Jan 1, 1990

By L. G. Austin

A simple finite difference algorithm has been used to compute a simulation model for unsteady-state ball milling. The model considers the mill to act as if it were three fully-mixed reactors in series (one-large/two- small), it incorporates the-Rogers-Austin mass transfer law relating mill hold-up to flow rate through the mill, and it allows for the reduction in breakage rates caused by over-filling of the mill at high flow rates. The computation is rapid and requires only small storage space. Examples are given of use of the model.

Jan 1, 1984

By Douglas M. Dwosh

INLAND STEEL COAL COMPANY'S experience with a gypsum cement, with and without fiber glass filler, indicates that the concept of utilizing standard rock dust equipment to dry handle and apply gypsum cement as a mine sealant is feasible, simple and economical. Prior to 1975, Inland had casually experimented with a few sealants and had discussed the advantages and shortcomings of other sealants with various users. Hower in mid-1975, Inland foresaw the need to seriously acquire a practical sealant system. There were nearly a dozen sealant materials on the market at that time: silicate-based materials, Portland cements, vermiculite cements, gypsum cements, and magnesium-oxysulfate cements, each with their own fillers and additives. The applicating equipment ranged from simple to complex: wet mix or slurry machines operating on either a batch or continuous basis, high viscosity pumps, and pneumatic, dry conveying machines with water nozzles. Compounding the selection process, two or more products could often be used with the same machine, or a given material could be successfully applied with more than one type of machine.

Jan 1, 1976

By H. R. Coles

Test work conducted in the 6.4 and 10.52 m Aerofall Mills at the Iron Ore Company of Canada Carol Project showed that the conventionally used ?deflector?-type liners which form the basic principle of Aerofall Mill grinding did not necessarily provide the best grinding performance. A new design, using low profile liners incorporating radial ribs of a proper height, actually improved the mill throughput in the order of 9 to 20% without sacrificing grinding efficiency. In addition, the new design reduced liner weight and scrap losses, which resulted in a reduction of liner consumption by 25%. It provided better protection to the mill shell and reduced the overall maintenance cost for the mill

Jan 1, 1980

By A. J. Kwitowski

Teleoperation is a technology that can provide significant health and safety improvements in mining, by relocating machine operators hundreds of meters away from the face area. The U. S. Bureau of Mines (USBM) has recently developed a teleoperation system for continuous mining and haulage equipment. This system features near-real-time closed-loop control. A prototype system was developed and demonstrated on the surface. This system could be used in thin-seam applications down to 914 mm. Details are provided on the developed teleoperation system, results of testing, and expected, future applications of this technology for improved safety.

Jan 1, 1994

By Alton G. Woody

Like so many installations of its type approaching middle age, the ore processing and shipping facilities in Puerto Ordaz, Venezuela, have taken a lot of twists and turns in their lifetime. The object of this paper is to lead you through these twists and turns and some of the reasoning for them. The need for additional sources of iron are in the United States became evident during the time of the second world war. An exploration team from U. S. Steel located further high quality direct shipping iron are in commercial quantities near Ciudad Bolivar, Venezuela in 1947. Basic decisions were made to develop these reserves for export via the Orinoco River through a new shipping port to be built at the confluence of the Orinoco and Caroni Rivers. The basic concept was for the ore to be loaded directly to ocean going vessels. This was something of a gamble since the basic economics depended upon successfully opening up the main channel of the Orinoco River to deepwater vessels, and the Bethlehem Steel mine in the same area was already working with shallow draft river boats and a transfer station on the coast. Always, the basic philosophy has tended to be to plan with expansion in mind. The original conveyor systems were 1.52 m (60 inches) wide with 200 idlers, whereas 1.07 m (42 inches) or 1.22 m (48 inches) wide conveyors could have carried any production foreseen at the time of installation. Stockpiles have been located and designed with room for expansion. Basic designs have had dotted line future expansion blocked in.

Jan 1, 1978

The Australian states of New South Wales (NSW) and Queensland, because of their endowment of black coal resources, dominate the production and export statistics for Australian coal. NSW produced 86 million tonnes of saleable coal in 1994, representing a doubling of output since 1980, or a growth of 5% per annum. Asian demand for thermal and coking coal has, of course, driven this growth in NSW. This high Asian demand is forecast to continue and NSW will seek to secure its share. This paper focuses on some of the issues facing NSW in the future, and in particular, examines some of the major new and proposed mining projects.

Jan 1, 1997

By T. E. Durney

In the Fall of 1987 The Wellmore Coal division of The United Company installed a fines separation circuit in its #20 plant near Big Rock, Va. The addition of the fines circuit included a bank of classifying cyclones and two flotation units; one a conventional 4 cell, 34 m3 Wemco cell, the other an 2.4 meter diameter by 7.6 meter tall, 28.3 m3 column flotation cell. The new fine coal separation circuit is depicted in Figure 1. The column flotation cell is manufactured by the Deister Concentrator Company, Inc., under the trade name Flotaire. The Deister Flotaire column cell utilizes a counter current flow arrangement and a different means of generating air bubbles than that of conventional mechanical flotation cells found in coal processing plants. Other features include diffusers for additional air supply and a froth washer. This cell is one of the few commercial scale column cells processing coal.

Jan 1, 1990

By Roland W. Merwin

The Bureau of Mines has studied the possibility of using the heap leaching process for treating the gold ores in the sedimentary beds of northeastern Nevada. This paper summarizes all available information on the technical and economic feasibility of heap leaching oxidized ores from these beds, past industry application of vat leaching, results of recent Bureau of Mines and industry tests on heap leaching ores from this region, and requirements for planning the proper application of heap leaching. Preliminary tests on representative samples of ores from the region show that a satisfactory recovery of gold can be obtained by heap leaching the ores with cyanide at a relatively coarse size. Significant deposits of gold ore occur in sedimentary beds of various locations over an extended area 40 miles wide and 200 miles long in northeastern Nevada. The area is centered 40 miles west of and runs parallel to the leading edge of the Roberts Mountain thrust fault system, a prominent geologic feature in the area. The general locations of past and present gold mining operations are shown in figure 1. (slide 1)

Jan 1, 1969

By Rudolf E. Greuer

Modeling a mine ventilation system is a formidable mathematical problem requiring the solution of twice as many equations as there are airways with half of these being quadratic equations. The addition of a mine fire to the problem adds many more complexities. The U.S. Bureau of Mines and Michigan Technological University attacked this problem in stages. During the 1970's and 80's, a series of computer simulation programs were developed which offered progressively increasing levels of modeling capability and accuracy. The current version of this software, MFIRE 2.0, was released in 1993. This programs provides for full dynamic state mass flow-based modeling of a mine ventilation system, and includes natural ventilation, mechanical ventilation, air reversals and recirculation, methane and fire contaminant spread, and moisture condensation and evaporation in the mass flow and heat exchange calculations. This program is a useful tool for routine ventilation planning and can significantly improve mine safety by enabling detailed quantitative analysis for mine emergency preplanning. This paper reviews the evolution of the MFIRE program from its infancy as a simple digital network simulator replacing analog computers to the present version.

Jan 1, 1994

By John J. Dran

In recent years, market rates of interest have risen well above their historical long-term average. Also during this period, the short-term variability of interest rates has been greater than in prior years. Interest rates have a significant effect on the operation of our economy. They influence the extractive industries in a number of ways. Their major long- range impact is on investment decisions - specifically the valuation of mineral deposits. An understanding of the factors that influence interest rates is important to the engineer or businessman who makes the investment decisions for the mining company. The effect of changes in the market rate of interest on the value of mineral reserves is critical to the future financial success of the mining enterprise. The most common simplification of the factors determining the level of interest rates is that they are a function of the demand for and the supply of money. While this is an oversimplification, most businessmen would be hard- pressed to provide a better explanation. The purpose of this paper is to explore certain fundamental economic aspects of interest rates and to examine their effect on the analysis of investment in mineral deposits.

Jan 1, 1975

By Ihsan Berk Tulu, Mustafa Can Suner

The synthetic rock mass (SRM) approach and discrete fracture network (DFN) model, generated from the field surveys, are novel methodologies to study fracture rock mass behavior. In this paper, SRM and DFN methodologies were used to understand the influence of natural fractures on the mechanical response and failure mechanisms of stone mine pillars. First, a multi-stage up-scaling procedure with the homogenization process is established. Later, a stochastic sampling process on the SRM model to have further insight on the stone mine pillar mechanics is performed. Two-dimensional Universal Distinct Element Code (UDEC) is utilized to represent intact rock with the Voronoi-Trigon discretized blocks and to capture fractured rock mass behavior. The laboratory-size limestone mine rock specimens are systematically up-scaled to the average width of the field-size stone mine pillars. Then, the DFN model, generated from field data, is sampled to construct the SRM of the field-size pillars. By doing so, the effect of discrete discontinuities on pillar stability is studied by assessing the pillar strengths and failure mechanisms in various width-to-height ratios.

Jul 8, 2022

By Robert K. Jones

Filter media can be defined as that material which effects the removal of finely divided solids from a fluid. Thus the removal of dust from air or turbidity from water, for example, can be the result of passing the fluid through a properly supported filter media. Since filtration in one form or another has been practiced since pre¬historic times filter media have been made from an extremely wide variety of materials. Vegetable and synthetic fibers (used loose, or formed into papers, felts or cloth) sand, ground coal, diatomite, perlite, wire cloth, porous metal, and bonded aluminum oxide are among the more important materials used today.

Jan 1, 1961