Search Documents

By A. K. Bakshi

Slurry rheology affects autogenous grinding performance by changing the rock's breakage characteristics. In this study pilot scale batch autogenous grinding was carried out to observe the effect of viscosity on the breakage characteristics of the rocks (the media), and on the overall specific energy consumption. Clay/fines content, and temperature of the initial charge, were varied to alter the viscosity of the slurry. Results showed that at higher slurry viscosity, rocks became more difficult to break, resulting in an overall increase in the specific energy consumption of the mill. Also, it was observed that viscosity had a significant effect on the amount of critical size material present in the grinding circuit, where the critical size material is the material which is too large to be effectively ground in the mill, and too fine to act as grinding media.

Jan 1, 1996

By Garry W. Warren

The electrochemical oxidation of chalcopyrite in the absence of-a chemical oxidant was studied in ammonia/ammonium sulfate solutions by anodically polarizing electrodes prepared from massive chalcopyrite. The effects of pH, cupric and ammonia ion concentration were systematically evaluated. Kinetic parameters were obtained from the anodic charge-transfer regions of the anodic polarization curves. Increasing ammonia and hydroxyl ion concentrations increased the rate of oxidation. A mechanism is proposed which explains the first order dependence of (NH3) and (OR) associated with a single electron transfer process. An empirical relationship which accurately describes the dependence of the rest potential (i.e. zero current potential) on solution composition is also given.

Jan 1, 1978

The 86th Annual Meeting of the SME Minnesota section/74th Annual University of Minnesota Mining Symposium partnered with the Canadian Institute of Mining Metallurgy and Petroleum (CIM)?s Iron Ore Symposium for a historic joint conference, held this year in Duluth, MN, April 15- 17. One of a flurry of recent collaborations between SME and CIM, the joint conference was a natural fit for the conference held in the heart of the Iron Range. As CIM National President Terence Bowles said in his joint keynote with SME President Jessica Kogel, ?The U.S. imports $51 billion from Canada and Canada imports $38 billion the U.S.; that?s 50 percent of Canada?s exports and 51 percent of its imports.? The two countries? economies are linked, and nowhere more closely than in their iron ore mining activities. Kogel opened the conference with a plenary speech identifying the top 10 issues facing mining and how these issues present opportunities for mining companies. She said that it is important that the mining industry stay flexible and adapt to changing conditions, or it will go the way of the dinosaur. However, she said that these challenges can lead to new opportunities. For example, one of the major challenges facing mining is the current state of risk aversion among investors, which makes for ?less money in the pipeline.? However, this situation creates a better climate for mergers and acquisitions, which is another, less risky way to get funding. Likewise, another challenge globally is geopolitical risk; this challenge is likely to drive growth toward stable countries, which was good news for an audience composed mostly of Minnesota and Canadian mining industry personnel. One of the highlights of Kogel?s address was a triangle illustrating the interdependent nature of sustainable development and corporate social responsibility (Fig. 1). This triangle consists of four equal components: the social environment, transparency, local and global impact and future generations. The most important takeaway, Kogel said, was that sustainable development and environmental and social responsibility, while they do add to the cost of doing business, are no longer optional.

Aug 1, 2013

Rendering a solid hydrophobic and solid-fluid particle* attachment in flotation are recognized as not necessarily related (1,2). The attachment is governed by forces of attraction and repulsion which need to be considered. The induction time required for attachment after solid and fluid particle are brought into proximity (3-8) illustrates the point. Laskowski(8) showed that a reduced induction time favoured flotation but detected no change in contact angle, a standard indication of solid surface hydrophobicity. Induction .time is observed in fluid-fluid particle coalescence, there being called a rest time (9-11) The induction time phenomenon is related to the presence of a metastable liquid film (disjoining film (2)) of the continuous phase (water in flotation) which must thin and rupture to permit attachment. The lifetime of this film, which is governed by the rate of thinning and the probability of rupture with thicknesss, depends on a complex interaction of forces. Investigating these forces should help clarify the attachment process. Practical benefits would be improved understanding of slimes flotation (12,13) This paper is concerned with the role of the mobile fluid particle-water interface on the film lifetime, in particular, the role of time-dependent or dynamic interfacial properties resulting from deformation of this interface.

Jan 1, 1975

By R. J. Heath

Potash, the general term for potassium salts used as fertilizers, is one of the essential growth nutrients (together with nitrogen and phosphates) required by all living things. Total world consumption of potash for fertilizer use - almost all of it in the form of potassium chloride - amounted to an estimated 47 million short tons in the 1979/80 fertilizer year*. While there is some limited demand for potash for a variety of industrial applications, this amounts to only 3 or 4 per cent of total world demand, and the potash business can be viewed as essentially a fertilizer business. Total available world potash production in the 1979/80 fertilizer year also amounted to approximately 47 million tons. There are two large potash producing countries - Canada and Russia - and a number of other countries where production is significant - East Germany, West Germany, the U.S.A., France, Israel and Spain. Production volumes are shown in Table 1.

Jan 1, 1980

By Norman F. Schulz

The Davis magnetic tube concentrator is a laboratory machine designed to separate a small sample of pulverized magnetic iron ore into magnetic and non-magnetic fractions. It was developed in 1921 by mechanization of a test previously performed manually. (1)(2)(3)(1) No significant changes have been made in the design of the apparatus since that time. The Davis magnetic tube test continues to serve as a practical basis for judging the amenability of an ore to magnetic separation and for controlling magnetic separation plant operations. The apparatus consists of an inclined cylindrical glass tube supported adjacent to closely spaced pointed poles of a powerful C-magnet. (Figure 1). To conduct a tube test, a sample of a suitably prepared ore is poured into the water-filled tube. With wash water flowing through, the tube is oscillated to gradually reject the weakly magnetic ore particles until the desired degree of separation is attained. Both the magnetic concentrate and the tailings may be recovered for examination.

Jan 1, 1963

By P. James

"INTRODUCTION High sulfate (SO4-2) levels often occur in MIW (mining influenced water) either as the result of oxidation of sulfide minerals exposed by mining activity or by deliberate addition – commonly by sulfuric acid (H2SO4) use in hydrometallurgical leaching activities. Increasing regulation of sulfate discharge is creating new pressure to treat or mitigate sulfate release to prevent its entry into the environment. Current treatments include precipitating as gypsum during lime treatment, filtration separation using membranes such as reverse osmosis and nanofiltration technology, and biological elimination via methods like constructed bioreactors. Blue Planet Strategies (BPS) focuses on improved resource utilization targeting electrolytic treatment and waste conversion into resources and has now demonstrated that its proprietary DEMET™ (Dynamic Electrolytic Metal Effluent Treatment) platform can also remove sulfate from target streams as a byproduct of its usual primary treatment focus points of metal species elimination and/or pH adjustment.[1-6] This powerful new capability can mitigate sulfate contamination and recover the sulfate in a useful and potentially saleable form as a byproduct of improved primary treatments focused on enhancing production or treating waste. This provides a new treatment opportunity and value proposition for lowering overall sulfate consumption/addition or creating new revenue to defray conventional treatment costs. The DEMET Alternative DEMET utilizes a patented electrolytic technology platform employing proprietary dynamic high surface area electrodes in innovative configurations to achieve a variety of novel selective chemistries. DEMET‘s unique elements can yield higher processing rates at practical efficiencies, lower energy consumption, plus improved processing stability and lower maintenance requirements due to enhanced resistance to cell fouling and shorting; while also thwarting cross stream (catholyte vs. anolyte) contamination. Consequently, DEMET can provide a superior, extremely versatile, and cost-effective electrolytic treatment option where a multitude of FEED and PRODUCT stream combinations might be employed in comparison to traditional tankhouse electrolytic cells. Secondary reactions (Figure 1A) which could also occur at the cathode (plating/electrowinning, precipitation/scale formation, etc.) are controlled through process tailoring and operation parameter selection. Additionally, DEMET‘s innovative dynamic system mitigates potential fouling and electrode occlusion or shorting challenges which could occur when process particulars demand some of these secondary side reactions occur."

Jan 1, 2015

By Fathi Habashi

THE MINERAL monazite (µ?v??e?? = to be alone) is a rare earth phosphate containing some thorium and small amounts of uranium. It is widely distributed in the earth's crust. It occurs in small proportions in granites. Table 7-1. Mineralogical analysis of Rosetta black sands, U.A.R. (Nakhla, 1958). [Black sands Concentrate Augite 10.8 - Calcite 1.1 - Felspar 0.1 - Garnet 1.8 - Hornblende 2.4 - Ilmenite 50.7 8.0 Magnetite 15.3 Monazite 1.1 84.3 Quarz 7.3 - Rutile 1.0 0.5 Titanite 0.2 - Zircon 7.3 7.1 Others 1.0 0.1 100.0 100.0]

Jan 1, 1970

By Bradford F. Townsend, Robin B. Dill, Richard M. Croswell

Innovative geotechnical construction techniques were used to construct three pedestrian tunnels under a building slab-on-grade to allow utilization of basement space for manufacturing. Tunnels were constructed using mining techniques through granular fill soils less than three feet below on-going sensitive manufacturing operations. Project design consisted of jet grout underpinning of exterior foundation walls and an arch of drilled-in grouted horizontal dowels for soil pre-support to limit ground movements during excavation. Permanent tunnel lining consisted of arched steel rib sets and invert struts supported on precast footings encased in cast-in-place concrete slab and side walls and a gunite arch.

Jan 1, 1993

By R. E. Hucko

The goal of the U.S. Department of Energy (DOE) coal preparation R&D program is to develop technology to reduce the ash and sulfur contents of United States coals to levels such that the resultant product can be formulated into a high- quality solid or slurry fuel that could replace oil or natural gas in both new and retrofit applications. The Coal Preparation program is implemented by the Pittsburgh Energy Technology Center (PETC) and is conducted both in-house and by a cross section of industrial organizations, universities, and national laboratories.

Jan 1, 1986

By Richard C. Neavel

Among the many compositional parameters used to judge the quality of a steam coal is the fouling factor of Attig and Duzy1 [% base in ash % acid in ash X % Na20] in ash. The higher the fouling factor, the more likely the heat transfer surfaces of the boiler will acquire a deleterious deposit of sintered ash. While examining the elemental composition of ash from various size and gravity fractions of coals from Illinois, we noticed that variations in the fouling factor were attributable mostly to variations in the sodium content. Further, sodium content was essentially the same in all sink-float fractions from a given coal. In other words, sodium was related neither to the ash nor to the organic material. We therefore concluded that the sodium was most likely in the pore water, which was approximately a constant proportion of all fractions. This led to the supposition that the sodium might be removable through water extraction. This supposition tended to confirm the observations of Daybell,2 Daybell and Gillham,3 and Gluskoter and Ruch4 that much of the sodium in coals existed as water soluble sodium ions. In passing, it should be noted that most sodium in Western U.S. coals (i.e., Wyoming, North Dakota, Montana) is not water soluble, but rather is fairly strongly held in association with the organic material (ion-exchanged).5 Because data reported in the literature were not very conclusive about the typical proportions of sodium that might be removed by water extraction, and because there were few data indicating extraction rates, and finally, because our calculations showed a favorable economic incentive to lower sodium contents, we initiated an experimental program to investigate water extraction of sodium from Illinois coals.

Jan 1, 1976

By Terry A. Ring

Sand bed filters are used to remove large and small particles from liquid streams. The large particles are removed by the straining action of the filter bed and the small particles are removed by particle deposition on the surface of the bed particles. Particle deposition, while being essential for the filtering action of colloidal particles, is not the only process that occurs in the filter bed. Other processes that occur are (1) the substrate becomes filled with particles limiting further deposition, and (2) some deposited particles are resuspended. The sum total of all these processes determine the performance of a filter bed.

Jan 1, 1982

By H. E. Wyslouzil

The highly competitive nature of the international iron ore market has forced producers to improve the quality of their pellets. The demand for low acid pellets suitable for direct reduction has resulted in an increase in the number of plants utilizing reverse froth flotation for silica reduction. Column flotation is being favoured for this service due to the low capital and operating cost of the equipment, as well as improved metallurgical performance when compared to conventional flotation cells. This paper describes the benefits of column flotation and discusses some important aspects of circuit design.

Jan 1, 1993

By Jacques Mongrain, Serge Barbeau, Gary Brierley

The Communaute Urbaine de Montreal is currently involved in construction of the South Interceptor which consists of 53 kilometers (33 miles) of 1,800 mm (6.0 ft) to 5,400 mm (18.0 ft) diameter tunnels for the purpose of collecting, storing, and delivering sanitary and combined sewage to the treatment plant. Work is divided into ten separate contracts; nine of which have already been bid. The purpose of this paper is to describe construction activities that have been performed through the end of 1986 with emphasis on a general layout of facilities, a summary of subsurface conditions, and brief descriptions of actual construction activities for the six contracts where tunneling has been performed. All projects are being excavated with tunnel boring machines.

Jan 1, 1987

By M. E. Rossi

Reconciliation of long-term block model reserves and mine production frequently shows significant discrepancies. This reconciliation can be done comparing the long-term block model reserves against a grade control model (generally, a model based on blast holes or production data). in this paper called an FI factor for tonnages, grade, and ounces; and also it should be done comparing the grade control model to the mill feed (or loaded to heaps) tonnages, grades and ounces (called an F2 factor). The long-term model usually contains blocks with dimensions larger than the size of the selective mining unit (SMU) of the operation. The smoothing effect of an estimator such as kriging will generally result in a grade-tonnage curve that does not match the grade-tonnage curve of the SMU's to be recovered. This problem is partly to blame for the reconciliation discrepancies found. In addition, in-pit perfect selection is impossible. and therefore the grade-tonnage predictions based on blast holes also need to be assessed, considering both unplanned dilution and the errors of estimation of the grade control model. This paper will focus on using conditional simulations to assess the uncertainty of the predicted grade-tonnage curve in terms of minable reserves, and in the framework of long-term mine planning. Quantifying the uncertainty in no uncertain terms is done in conjunction with a popular pit optimizer, which will yield not one, but several possible minable reserves, and therefore a range of possible minable tonnages and grades per pit shell or scheduled phase. This is a step further from the usual sensitivity analyses that are performed for deposit evaluation or development planning. Specifically, this approach takes into account the volume-variance relationship, the selectivity of the mining operation, planned and unplanned dilution. and carries the local uncertainty implicit in grade estimation into the mine design and mine planning phases. The motivation for the approach is discussed through an example, as well as a description of the procedures and steps involved.

Jan 1, 1998

The Bureau of Mines has studied 260 underground coal mine fires which occurred from 1970 through 1989. Every fire had the capacity to be hazardous to life and property, however upon closer examination some were found to be inherently more dangerous than others. Our research involved reviewing and recording specific information contained in published Mine Safety and Health Administration fire accident reports. The objective was to determine if degrees of hazard relative to fire source or location could be construed from information contained in the reports. We specifically looked at the propensity for fires to cause injuries and fatalities as well as the need to seal the area in order to extinguish the fire. Relative to all underground locations, this review found that fires occurring in main haulage-ways were most likely to cause injuries and fatalities as well as require sealing of at least the immediate area to extinguish.

Jan 1, 1993

By J. E. Hoffman, Massimo Maccagni, T. J. Keefe, Marco Olper, O&apos

The research laboratory of B.U.S Engitec has identified and patented a new process for electrolytic production of lead from lead sulphide concentrates with simultaneous production of elementary sulphur. The process occurs in an aqueous solution, at atmospheric pressure, utilizing a solution of ferric fluoroborate in fluoroboric acid as the oxidizing and solubilizing medium for lead sulphide. After the filtration and separation of a residue composed of elementary sulphur and the gangue which accompanied the concentrate, the solution containing lead as fluoroborate and iron reduced to a ferrous state is sent to a diaphragm electrolytic cell where, in the cathode compartment, the lead is deposited in a compact form on the stainless steel permanent blank. The exhaust solution stripped of lead is sent to the anode compartment where the oxidation of ferrous fluoroborate into ferric fluoroboratetakes place, reproducing the oxidizing solution for new leaching. Depending on operating conditions, it is possible to selectively solubilize the lead from the other metal values present in the concentrate. The sulphur produced from the reaction may be separated from the gangue by extraction with solvent or by flotation.

Jan 1, 1993

By John Brouwer

Through the use of good preventive maintenance procedures in which the work of both production and maintenance personnel is well-coordinated, production downtime can be drastically minimized, and costly repairs and interruptions in planned maintenance and production schedules can be eliminated. There had been some conflict in the past between production and maintenance people over the proper method of achieving maximum machine performance. The usual practice was to operate production equipment at maximum capacity for the longest possible time until breakdown occurred, and then make hurried repairs to get back into production. In most cases, these repairs involved unscheduled work and were thus performed inefficiently. Both production and maintenance have the same objective: to produce a quality product at maximum efficiency and at minimum cost. Preventive maintenance is a common tool available for both production and maintenance personnel to achieve this objective. Actually, one of the main objectives of preventive maintenance is to find any abnormal machine condition that may cause machine failure before a breakdown occurs. This makes it possible to plan and schedule maintenance work with the least amount of interruption and plan production volume with a higher rate of accuracy. Maintenance people prefer to perform this work on a scheduled basis and get away from the "crash" situation that accompanies breakdowns. They thereby increase the utilization of available manpower and machine time, prolong equipment life, and improve maintenance costs.

Jan 1, 1979

By F. J. Sotillo

"Scrubbing both horizontal (drum) and vertical (attrition) are considered simple unit operations in the beneficiation of phosphate ores. In general, the operating conditions are fixed at high solids content based on the experience of the engineering or equipment manufacturing company responsible of designing this beneficiation step. Nevertheless, scrubbing is a complex unit operation designed to clean the surfaces of phosphate mineral particles of slimes, break loose weak inclusions or attached particles of impurities, and break aggregates of clayish material. Therefore, it is considered that as high solids content as possible should be used to enhance particle-particle interactions (impact and rubbing) without taking into consideration the rheology of the system. However, scrubbing unit operations design requires studying the balance between the increase of particle-particle interactions with the cushion effect that may occur when slimes, clays and fines decrease the availability of free water increasing the apparent viscosity of the phosphate slurry up to that of a paste consistency. This paper presents data from laboratory tests to determine the best operating conditions for the design of these unit operations based on the highest P2O5 grade obtained with the lowest impurities for different size fractions. INTRODUCTION In the beneficiation of phosphate ores, unit operations such as horizontal scrubbing (drum) and vertical scrubbing (attrition) are considered simple unit operations. Therefore, little attention is given to the design of horizontal and vertical scrubbing during the basic engineering studies, and the detail engineering stage, the manufacturers recommending “standard” units and operating conditions based on their experience. Due diligence of several beneficiation phosphate plants at industrial scale indicates that a deficient scrubbing of the phosphate ore results in significant problems in downstream unit operations, such as classification, clarification, gravity separation, magnetic separation, flotation, dewatering, and filtration. Scrubbing is in fact a complex unit operation designed to clean the surfaces of phosphate mineral particles of slimes (clays and fines), break loose weak inclusions or attached particles of impurities, and break aggregates of clayish material. Two phenomena occur, the particle-particle interaction (impact and rubbing), and the rheological effects of releasing significant amount of fines into the slurry. Therefore, high solids contents are recommended to enhance the particle-particle interactions, which may result in a change in the rheological regime of the system due to the slimes, clays, and fines decreasing the availability of free water. This increases the apparent viscosity of the system up to that of paste consistency resulting in a cushion effect that suppresses scrubbing. Under these conditions, not all fines are release and rejected (deslimed), downstream unit operations being affected by the release of clays, resulting in P2O5 losses."

Jan 1, 2017

By I. Iwasaki

The effects of autogenous grinding and conventional grinding on the floatabilities of copper-nickel sulfides were investigated as a part of a pilot-plant development project on the differential flotation of Duluth gabbro. At the same mesh-of-grind copper, nickel, and cobalt recoveries were higher and residual sulfur in the flotation tailings was lower with the autogenously-ground pulps. With the ball-mill-ground pulps the residual sulfur in the tailings could not be lowered to the level attained by the autogenously-ground pulps even at increased levels of the collector addition. From mineralogical examinations of concentrate and tailings samples, an electrochemical interaction between grinding media and sulfide minerals was thought to have a greater effect on sulfide mineral flotation behavior than the breakage characteristics of the ore samples in these two types of mills.

Jan 1, 1981