Search Documents

By S. J. Schatzel, V. Gangrade

A ventilation research study was conducted by the National Institute for Occupational Safety and Health and a cooperating trona mine in the Green River basin of Wyoming, USA. The mine operation uses the longwall mining method in trona bed 17, a commonly mined unit in the region. The longwall face length is 228 m (750 ft), and caving on the face occurred up to the back of the longwall shields. The mine is ventilated using a main blowing fan and a bleeder shaft. For this study, sulfur hexafluoride (SF6) tracer gas was released in two separate monitoring experiments. For the first experiment, tracer gas was released on the face, this test focused on airflow along the longwall face of the active panel. Face test showed the airflow patterns to be more complex than just head-to-tail flow in the main ventilation air stream on the active panel. For the second experiment, tracer gas was released 2 crosscuts inby the face on the headgate side, this test focused on gas transport in the mined-out portion of the same active panel. Gob test showed a pathway of movement through the front of the active panel gob that moved outby from the tailgate corner. The primary pathway of tracer gas movement in the active panel gob was towards the headgate and tailgate bleeders and out of a bleeder shaft. The rate of movement towards the back of the gob was measured to be 0.19 m/s (37 fpm).

By J. Sidhom, W. Fourie

"As the mining industry continues to face difficult challenges the need to persistently focus on productivity and utilization of labor and equipment costs will intensify. With these challenges in mind, Joy Global is helping to bring mining performance and analytics to the next level. By evaluating underground haulage, a significant component of the Room and Pillar mining value stream, variables have been identified and sensitivities have been performed to show opportunities to balance and streamline throughput. As a result of applying operational excellence tools to the mining environment, Joy Global is seeking to optimize mining performances by limiting waste, simplifying the process, increasing productivity and machine utilization, as well as removing workers from harm’s way. These days it’s not enough to work harder; mines have to work smarter. Improving efficiency, reducing costs, increasing safety: these are no longer ‘nice to haves’, they are ‘must haves’. Starting with the best products and the right people is a first step, but then what? How do mines take their operations from just OK to being a top performer? By using operational excellence principles aimed at eliminating waste, simplifying processes, automating where possible and removing people from harm’s way. The fundamentals of operational excellence (OpEx) are based upon the DMAIC process, which stands for define, measure, analyze, improve and control. DMAIC is an improvement cycle that helps with, for example, haulage optimization by: defining the issues and problems in the process as well as the areas of improvement; measuring and collecting mining operational data by time study and equipment monitoring system; analyzing through sensitivities and production modelling to determine root causes; then improving the performance and controlling the operation. Joy Global uses Joy OpEx or ‘lean’ principles inside its organization to drive efficiency, but it also helps its customers employ them to achieve new levels of productivity and safety. These same principles can be applied in most situations to streamline processes, improve operations and deliver value. As applied to mining, OpEx is seen as moving the needle on value creation by first identifying the value stream, then analyzing the areas that are not optimized. Once defined, these areas are ‘designed out’ of operational processes to create an automated operational flow. At a US coal mine, Joy Global was brought in to apply Joy OpEx principles to optimize mining and haulage to improve productivity and reduce costs. This multi-phase process started by defining the existing systems challenges to start finding areas for improvement."

Jan 1, 2017

By Eric Lundgren

The mining paradigm is changing on the continent of Africa. Jessica Kogel?s closing statement from her September 2013 President?s Page (ME, September 2013, pp. 6) has never been more appropriate, ?Africa is shaping up to be the next mining powerhouse, and there is huge opportunity for local communities, national governments and private industry to work together to create a win-win situation for all.? Supporting this notion, attendance at numerous industry conferences around the world demonstrates the shift toward a more sustainable, more environmentally conscious extractive model. But questions remain: How effectively is the industry making this transition, and how willing are companies to learn from the experiences of others? The international development community, as we like to call ourselves, is going through a parallel shift. We are experiencing our own funding crisis; governments are not as flush with resources as they were pre-economic meltdown. But more importantly, after a half century of implementing development programs, we must admit that while some of our programs have been fantastically successful, too many still fail to achieve the goal of poverty alleviation for the world?s poorest. Moving forward, we are forced to recognize that achieving success in scale and sustainability is not always accomplished from our work alone. As the director of international programs for Africare, a nonprofit with more than 40 years of experience implementing community-based development programs in Africa, I can report that our organization is changing the way we think about successful development partnerships. Africare recognizes that for too long the mining sector and nonprofits have been at odds, choosing noncommunication as a ?solution? to the problem. Both sides now recognize that this standoff is outdated, and Africare, specifically, is ready to cross the proverbial line. We see the potential benefits of mining for local communities and, when done responsibly, the opportunity to properly manage Africa?s resource boom as a benefit to all. There are challenges in this conversation. Many mining professionals view nonprofits as whistle-blowers, ready in a pinch to speak to news sources and complain about poor operational standards. Those are advocacy organizations, and while their role is important, they are not the only nonprofits interested in mining operations in developing countries. Organizations like Africare, with decades of experience implementing poverty reduction programs, approach this differently. We know we can work with mining companies to promote economic opportunity in the communities where mining operations are occurring. We recognize that the conversation is difficult, and we are open to discussions about how we can bring our unique experience to bear on the problems faced by mining companies in carrying out their investment programs.

Jan 1, 2014

By J. Bartrum

Semi-autogenous, (SAG), milling operations can realize substantial Increases in mill throughput by removing and crushing critical size, slow grinding, material from the SAG mill. Full-scale plant testwork showed that modifying the Kidston SAG/ball circuit to a semi-autogenous-ball milling-crushing (SABC) circuit would increase plant throughput by 25 to 30%. The methods used to determine the value of the SABC circuit and the design of the circuit are discussed.

Jan 1, 1988

By M. Sinirkaya

The dissolution process of phosphate rock from the Semikan area (Mardin-Mazidagi, Turkey) using dilute phosphoric acid has been investigated. The work involved studying the effect of important variables, such as reaction time, stirring speed, particle size fraction, phosphoric acid concentration and temperature. Van der Sluis et al.?s model was used to determine the rate of the partial dissolution of phosphate ore. Mass-transfer coefficients (kL) varied between 2.8 and 28.5.10-3 m.s-1. The activation energy of the process varied between 16 and 20 kJ.mol-1. It has been found that the dissolution process is controlled by calcium ion diffusion, rather than by chemical reaction.

Jan 1, 2010

By K. Getsos

Western Greece is a favorable site for exploration and discovery of oil fields. The most important potential source rocks seem to be all the rocks deposited before middle Jurassic under special circumstances, such as reducing conditions, which allowed preservation and maturation of the organic material. In general all the rocks of middle Jurassic to Paleogene are not favorite source rocks. The porosity type was studied on fifty samples using scanning electron microscopy (SEM). Potential reservoir rocks are the porous Paleogene wackestones-packstones with boring, channel and vuggy porosity type. Finally seal rocks are the impermeable mud-stones and wackestones of Jurassic, Cretaceous and Paleogene age. These rocks consist of micrite and whole sells of foraminiferas and the porosity type is mainly intercrystal/interparticle. A Total Organic Carbon (TOC) analysis, conducted on seventy samples using a wet oxidation method, has revealed an extremely low TOC content (less than 0.05 %). This amount is by far less than the minimum organic content amount, required for source rock characterization and characterizes all the rocks of middle Jurassic to Paleogene age. Additionally, 18O and 13C stable isotope analysis was contacted and the results are given in d values. All the rocks within the studied time interval have much lower d values than petroleum source rocks. Clay mineral content was studied in almost seventy samples. As is indicated by the clay mineral content the studied rocks have reached up to the Middle Diagenesis and the temperature during diagenesis was rather low.

Jan 1, 2006

By Winfield G. Wright, Philip L. Verplanck, Philip L. Hageman, Douglas B. Yager, Dana J. Bove, M. Alisa Mast

Geological, hydrological, and geochemical information synthesized in a Geographical Information System (GIS) for water and rock surrounding South and Middle Forks of Mineral Creek, northwest of Silverton Colorado, was analyzed to distinguish between the natural and the mining-related sources of metals to dace waters in the watershed An important natural source of metals to surface water emanates from a porphyry molybdenum deposit south and upslope from the Middle Fork of Mineral Creek. Interaction of surface and ground water with fractured, altered rocks and permeable, Quatemay-age surficial deposits produces downstream water quality that does not meet current State of Colorado water quality standards for metals and pH. GIS site characterization and three-dimensional modeling distinguish surficial deposits as volumetrically substantial, significant sources of naturally occurring metals that strongly influence water quality and complicate ongoing mine-site mitigation efforts. Our findings indicate that regional hydrologic and geologic information needs to be evaluated before realistic water quality guidelines are established and mitigation recommendations are confidently implemented.

Jan 1, 2000

By Shankar S. Hegde

In many areas of the United States much of the most readily minable coal is nearing depletion, while at the same time, increased national attention is being given to coal as a major alternate energy source. If some of the thinner, more erratic, deeper and lower quality coals, which comprise the great bulk of U.S. resources, are to be mined efficiently and economically, greater attention must be devoted to careful planning of mines and to preparation facilities. One of the cornerstones to careful and successful mine planning is precise knowledge of coal thickness and areal distribution, roof and floor quality, and seam quality. Data on which this knowledge is based are obtained from various borehole techniques and, in some cases, seismic methods. Despite the many technical innovations that have been made in acquiring subsurface data, little attention has been given to the problem of systematic storage and retrieval procedures of the data and assembling them in a form that can be used for various computer mapping programs now available. (See Bilter and Martin, 1977; Bryant and Zobrist, 1977 and Farrell and Wherry, 1978). The purpose of this paper is to describe a series of user oriented programs developed over the past five years which are specifically designed for precise logging of rock core, accurate storage and retrieval of this data, correlation of seams between logs, tagging seams, computer assisted data posting of maps and preparing maps and profile sections for report illustrations. The entire system stresses increased precision and speed for a series of operations which are now largely manual, time consuming and prone to error.

Jan 1, 1980

By A. Chieregati

"A heterogeneity study was conducted at Erdenet Copper Mine in Erdenet, Mongolia, to determine the fundamental sampling error associated with blasthole sampling. Using a custom designed sector sampler, six large blasthole samples were collected to perform the test that was developed by Pierre Gy, to estimate the constitutional heterogeneity factor for several types of ore. The study investigated the entire sampling protocol, from mine site to analytical laboratory, and quantified the contributions to fundamental sampling error (FSE) of the various stages of sampling and sample preparation. The total relative standard deviation (RSD) of sampling error was determined to be ±32% and ±49.4% for copper and molybdenum respectively. A classical statistics analysis conducted on the data confirmed the level of RSD. About 95% of the sampling error was produced from only one step in the sampling protocol: when the 1 kg sample was reduced to 50 g sample for chemical analysis. Therefore, it is recommended that the 1 kg sample be reduced to 50g using a slightly different protocol to minimize the FSE. The 1 kg sample should be first crushed to 0.2cm size. A 250g split should then be taken and fine ground. A 50g split should then be taken from the 250g fine ground split. These two simple steps will reduce the FSE to ±7.9% and ±17% for copper and molybdenum respectively. The modified sampling protocol effectively reduces the probability of misclassification of low grade ore to zero. INTRODUCTION The Erdenet copper-molybdenum open pit mine is located in Erdenet, in Orkhon province, Mongolia. The Erdenetiin-Ovoo copper-molybdenum deposit is between 1.5 and 3 km wide, and about 25 km in length (Erdenet Mining Corporation, 2016). Chalcopyrite, bornite covellite and chalcocite are among the major minerals found in the deposit. The mine processes approximately 26 million tons of ore annually. A study was conducted to evaluate the fundamental error associated with the blasthole cuttings and sampling protocol at the mine. The open pit mine uses 215mm diameter Russian drills to drill 17.5m holes for 15m benches. The total weight of blasthole cuttings for a 215mm diameter hole and 15m bench height is between 1.5 and 2 tonnes. This amount of sample is difficult and time consuming to collect and analyze. Therefore, a sector sampler was designed for the Russian drills to collect large samples that were representative of the blasthole cuttings (Ganguli et al., 2016). In order to eliminate the delimitation and the extraction errors, researchers consider sector samplers to be ideal for sampling blastholes (Pitard, 2008; Chieregati and Pitard, 2009). This method was intentionally more rigorous than the blasthole sampling protocol at the mine to ensure that the blasthole cuttings were properly sampled. This study was part of a broader study that also looked at the relationship between particle size and grade. The samples collected by the custom designed sector sampler were very large (195 kg on average), and therefore, sufficient for both studies. The relationship between particle size and grade has been reported in Ganguli et al. (2016)."

Jan 1, 2017

By Kenneth K. Landes

So far my consulting in industrial minerals has been confined principally to carbonate rocks,-salt, coking coal, and glass sand. Much of this work has been for companies either too small for a full-time geological staff or unaware of the value of employing one or more qualified geologists permanently. It gave me considerable personal satisfaction to see several of the latter companies employ one or two full-time geologists after the completion of a consulting contract with them. One possible reason why some companies lack the wisdom to hire geologists is that they are dominated by engineers who still subscribe to the old idea that engineers are self-sufficient in all fields. They could have learned this from their professors. I once knew a Dean of Engineering who got purple in the face when a faculty committee was discussing the financing of a broad gauged engineering project and suggestions were made that assistance be obtained from the Schools of Business and Law and from some of the science departments tie pounded the table and shouted "Engineers are trained to handle all this!" In teaching engineering geology some years ago I used to tell the class repeatedly that the course would not make them geologists, that the purpose was to teach them

Jan 1, 1972

By David Crouthamel, Raymond Henn

"The need to fill the void space or annulus created between an excavated tunnel or shaft and the final lining system has long been a requirement in underground construction. Most of those types of voids are created as a result of employing the two pass tunneling lining method. Filling of this void is called backfilling. For many years the materials used as backfill were primarily reinforced and non-reinforced concrete, sanded grout, neat cement grout, or blown-in sand/pea gravel. However, in the past 20 years the use of cellular grouts/cellular concrete as the backfill material has greatly increased. Most cellular grout is made of a mixture of water, Portland cement (with or without the addition of fly ash), a foaming agent and admixtures such as a water-reducer or superplasticizer.It is the authors’ preference to use the term cellular grout as opposed to cellular concrete since by ACI Concrete Terminology an ACI Standard (ACI CT 13), concrete contains aggregates. Normally cellular grout does not contain sand (finite aggregate), but almost never contain course aggregates.The authors believe there are several reasons for this increased use of cellular grout as backfill, such as:• The increase utilization of the various trenchless tunneling methods. Tunnels constructed using trenchless method tend to be smaller in size, excavated diameter or cross sectional area. Making man-entry for placing backfill from inside the secondary liner, utilizing pre-installed grout posts, more difficult if not impossible. It is these workspace restrictions that are the drivers as to when to utilize grout ports installed during the pipe/liner fabrication versus grout delivery pipes installed within the void/annulus space.• The ability of cellular backfills to be pumped and flow longer distances.• The unit weight of cellular grouts can be controlled by mix design and generally can range from 560 Kg/m3 (35 lbs/CF) to 1040 Kg/m3 (65 lbs/CF)."

Jan 12, 2017

By B. J. Huls

The commissioning of a Distributed Digital Control. System for the grinding circuit at Cuajone, was completed by mid August, 1985. Development of a successful strategy, excellent operator acceptability and the visual aspects offered by the display of the central console, improved mill throughput significantly. The inherent features of a digital system enhanced the flexibility in grinding control and allowed the mills and classifiers to be operated at maximum capacity. This paper discusses in detail the strategy development, the production restrictions encountered, and evaluates the overall performance of the digital control system. 1.0 Introduction In November 1976, the Cuajone Concentrator, located on the western slope of the Andes in Southern Peru, was commissioned to treat a nominal 41,000 TPD of ore. A systematic elimination of production restrictions has resulted in a continual increase of concentrator throughput to 48,700 TPD before the grinding control was in- stalled.

Jan 1, 1986

By W. H. Renison

This paper will discuss the operation and maintenance of Molycorp's Quests Mine ore conveyor system. The 1.2 m wide, steel cable-reinforced conveyor belts are capable of transporting 1089 kt/h of ore over a belt line distance of 3124 m with a vertical rise of 518 m. A portion of the conveyor runs in a 2057 m long underground decline on a 10° slope. Six 448 kW motors power the main 1.2 m wide belts.

Jan 1, 1984

By M. Dayne Aldridge

A discussion of the definition of automation in mine ventilation applications is presented. The results of theoretical studies, experiments and practical experience from work in the United Kingdom, Belgium, Poland, the Soviet Union and the United States are summarized. Conclusions are drawn from these efforts and the prospects for the future development of automatic mine ventilation systems are explored.

Jan 1, 1978

By Arun Kumar Singh

Wide variation in the nature of the coal seams and the surrounding rock mass of the Indian coalfields and very little information about the associated stress fields were observed to be the major hurdles in the straight forward application of a continuous miner (CM) based mechanised depillaring approach. Due to various techno-economic reasons, a considerably large number of coal seams have been developed and are standing on pillars in India. The development of pillars is done as per Indian coal mines regulation, which results in pillars of relatively large size. In fact, the large size of the pillars provides stiff natural support to control caving of the massive overlying strata. However, the size of these pillars is not conducive for the single pass pillar stripping technique and, therefore, there is a need for pillar splitting before pillar extraction/retreating. Splitting of the pillar may reduce the competency/stiffness of the pillar, which creates a chance of overriding during final extraction below a massive roof stratum. This paper first discusses the existing coal mining scenario in India followed by a brief presentation of geo-technical details of pillar extraction at the three sites where a CM has been introduced for depillaring/pillar retreating in the country to date. Based on past rock mechanics experiences with conventional depillaring faces, stability issues of the pillars, fenders, and stumps in and around the depillaring face are discussed. This may prove to be an important factor in the success of future CM faces. It is recognized that the application of the modern strata movement monitoring techniques may improve operation safety by providing valuable qualitative and quantitative information that can be used to improve the design of modern concepts like roof bolt based breaker line support during pillaring.

Jan 1, 2009

By Michael S. Moats, John Bailey Fletcher

Wear rates of grinding media can be misrepresented by marked ball wear tests (MBWT). Galvanic interactions between dissimilar grinding media can be affected by the chromium content in the media and the presence of oxygen in the environment. Corrosion, one component of wear, can be affected by many variables. Corrosion rates and corrosion potentials for modern high chromium white iron (HCWI) and high carbon steel (HCS) grinding media samples were obtained through electrochemical testing. In this study, the impact of chromium content in the grinding media and the dissolved oxygen in a simulated mill water solution on corrosion rates and potentials was examined. Increasing chromium content in HCWI above 15 weight percent increases the corrosion potential and decreases corrosion rate. Removing most of the oxygen from the solution lowers both the corrosion potential and corrosion rate of the materials tested. The electrochemical results were examined to model possible galvanic coupling effects on corrosion rates. Galvanic coupling between HCS and HCWI could cause differences in corrosion rates for almost all scenarios modeled. Based on the galvanic coupling analysis, MBWT results could be impacted by mixing HCWI and HCS in a ball mill charge. This impact is predicted to be more significant when dissolved oxygen is present in the mill water and as the chromium content of HCWI is above 15 weight percent.

Dec 21, 2022

By Albin E. Anderson

The PSM System has been available to the mining industry for nine years. During this time, many of the more than 160 Systems sold have been put to practical use and have provided the owners a handsome return on investment. In this paper, the author will briefly discuss how the System works and how it can be put to use in automatic grinding circuit control. Throughout, detailed consideration will be given to the many factors that can significantly influence how successful a specific application is.

Jan 1, 1979

By R. Kealey, D. Huo, Q. Zhang, Y. A. Sari

Greenhouse gas (GHG) emissions from primary mineral and metal production account for ~10% of global GHG emissions. One of the main sources of GHG emissions in mining operations is fuel consumption by haul trucks. Given their size and carrying capacity, the fuel consumption of haul trucks can approach 250 liters per hour. An average of 30% of the idle time of the trucks is spent while waiting in the queue. Inefficient truck dispatch planning can waste resources, cause dilution and elevate GHG emissions. In this research, a machine learning based truck dispatch approach was developed to dynamically route the haul trucks based on the loaded material, the road traffic, the estimated wait time, and the maintenance needs of the trucks. The GHG reduction potential of this smart fleet management approach was estimated by calculating and comparing the related carbon emissions versus scenarios using traditional fleet allocation approaches. Results suggest that this dynamic fleet allocation approach can significantly reduce GHG emissions at mineral production sites by optimizing waiting times and the overall distance travelled while achieving the same production levels.

Mar 2, 2022

By T. Vandergrift, J. Sturgill, W. Gerhard, J. Carrick

As surface minable coal is depleted, many operators look to high-wall mining to extend reserve life. Recent advances in highwall mining equipment have greatly improved productivity, clean coal recovery, and attainable penetration beneath the highwall. Somewhat lagging have been systematic design approaches for ensuring web pillar and overall highwall stability. This paper presents an overview of the design, planning, and field performance of a multiple-seam highwall mining application in southwest Wyoming. The safety and efficiency obtained to date is attributable to the careful geotechnical and operational planning described herein. Field confirmation of performance and suggestions for improvement are also discussed.

Jan 1, 2004

By Sunny Schoone, Maximilian Getz, Felix Leaman, ELISABETH CLAUSEN

Jan 5, 2023