Search Documents

By Don Painter, Nico Sutmoller, Lori M. K. Kahikina, Brian Dorwart

This paper will address the feasibility of using low-density cellular concrete (LDCC) for an annular fill application where project conditions required pumping the LDCC material for distances of up to 16,000 feet. These conditions occurred during construction of the Kaneohe-Kailua Sewer Tunnel in Oahu, Hawaii, between 2014 and 2018. Located on the island of Oahu, Hawaii, this 13-foot-diameter rock tunnel extends for approximately three miles from the Kaneohe Pre-Treatment Facility to the Kailua Regional Wastewater Treatment Plant. The tunnel was built to convey wastewater and provide temporary storage for peak wet weather flows entering the collection system, thereby reducing the potential for uncontrolled discharges. LDCC was chosen for this project partly due to its environmental benefits, which were essential for an application contiguous to the inland marine and coastal waters of the Pacific Ocean. In order to ensure optimal performance characteristics—compressive strength (with a requirement of 300 psi at 56 days), flowability, and light weight—were achieved, extensive testing of various LDCC products and mix designs was completed. The testing measured the initial set time of the LDCC as well as the compressive strength needed to reduce the quantity of grout lifts required for the project.

Jun 13, 2021

By I. B. Tulu, M. M. Sears

In 2015, 40 longwall mines provided nearly 60% of the US coal production from underground mining methods. This represents a substantial yet gradual increase from just under 50% over the last 5 years. As a result of this increased production share, the percentage of ground-fall-related fatalities in longwall mines has also increased when compared to all US underground coal mines. Additionally, about 80% of ground-fall-related fatalities have occurred in areas where the roof was supported. In an attempt to better understand the status quo of current US longwall support practices, a sample of 25 longwall mines were visited representing nearly 50% of the currently active longwall mines representing all of the major US longwall-producing regions. The resulting data was obtained from a wide variety of overburden depths, geologic conditions, mining heights, ground conditions, support practices, and gateroad configurations. The data collected is reported using both qualitative and quantitative methods. Results from the research update previous efforts in classifying mining accidents and injuries as well as current support practices presented by this author at the 2017 Society for Mining, Metallurgy, & Exploration Annual Meeting. This data provides a necessary background for future research aimed at further reduction of ground fall accidents and injuries.

By I. B. Tulu, M. M. Sears

In 2015, 40 longwall mines provided nearly 60% of the US coal production from underground mining methods. This represents a substantial yet gradual increase from just under 50% over the last 5 years. As a result of this increased production share, the percentage of ground-fall-related fatalities in longwall mines has also increased when compared to all US underground coal mines. Additionally, about 80% of ground-fall-related fatalities have occurred in areas where the roof was supported. In an attempt to better understand the status quo of current US longwall support practices, a sample of 25 longwall mines were visited representing nearly 50% of the currently active longwall mines representing all of the major US longwall-producing regions. The resulting data was obtained from a wide variety of overburden depths, geologic conditions, mining heights, ground conditions, support practices, and gateroad configurations. The data collected is reported using both qualitative and quantitative methods. Results from the research update previous efforts in classifying mining accidents and injuries as well as current support practices presented by this author at the 2017 Society for Mining, Metallurgy, & Exploration Annual Meeting. This data provides a necessary background for future research aimed at further reduction of ground fall accidents and injuries.

By S. Wegerer, M. Semel

The search for minerals typically starts with a reconnaissance phase. After finding a promising target area, further prospecting work will be conducted. Finally with growing confidence of having encountered an ore deposit with commercially viable concentrations of relevant minerals, an extensive exploration campaign will verify its potential. Best practice and reliable, efficient tools for mineral resource estimation of massive sulfide deposits in the deep sea have to be established yet. Therefore, a new seabed exploration system is in development. Various challenges are caused by the extreme environmental conditions in the deep sea and by the nature of massive sulfide deposits. Information of past and ongoing expeditions were gathered to form the basis of an in-depth requirement analysis. System functions and corresponding process times were derived. The experience from the existing MeBo seabed drill rigs serve as starting point for the concept study and following development. Initial MeBo system was built for maritime research purposes and now has to be converted into a new design, suitable for efficient and economic resource exploration. The new system configuration is modular structured to adapt easily to different application scenarios and challenges. To achieve an extension of the deployment depths, the overall equipment weight has to be limited through light weight construction and material. The drilling module contains a range of geotechnical coring tools to face the varying soil conditions of heterogeneous massive sulfide formations. The major challenge to overcome is the touch down sequence on uneven, 25° inclined, rough terrain in up to 4.000 m water depth. Furthermore, high precision of the final unit positioning is necessary. Landing sub-system proof of concept is validated in laboratory environment with small scale model. A novel seabed exploration system capable to land and operate safely on highly inclined slopes of mineral deposit is described. Obtaining high quality samples by wire-line coring technique is the objective.

Feb 22, 2026

By K. A. Foo

Minproc Resources Inc. is developing a tailings retreatment project in Bolivia at the Colquiri zinc-tin-silver mine, in the Bolivian Andes. Mining at Colquiri has been continuous since 1940 and COMIBOL, the Bolivian state mining company, has owned and operated the underground mine since 1964. There are 10 million tonnes of tailings at Colquiri containing 0.51% Sn, 4.21% Zn and 50 g/t Ag. Minproc plans to mine and concentrate the tailings at 1.15 million tonnes per year to produce feed for pyrometallurgical upgrading. The tailings are moderately complex, with cassiterite grain size ranging from 200 to 5 pm. The marmatite (ZnFeS) in the tailings is relatively easily recovered, with zinc recovery of 80% to a 40%-45% Zn concentrate. The major problem with the zinc metallurgy is that the marmatite is complexed with iron, which results in iron contents of 14%-17% Fe in concentrate. This makes the product very difficult to sell because of the low Zn:Fe ratio. Most zinc smelters require a Zn:Fe ratio of 6:1 or 7:1, whereas this concentrate has a 3:1 ratio. Concentrate sale terms are therefore unfavorable, and the high cost of transportation from Bolivia to the smelters is an additional burden.

Jan 1, 1992

By Stanley Noss

One need be neither an historian nor technologist to recognize that activi¬ties related to the conversion of coal to other usable energy forms have been active for nearly fifty years. The degree of such activity and its evolution to significant commercial proportions has, however, fluctuated widely with world circumstance. For the past decade there has existed both a consistent technology evolution effort in classic R & D proportions, and a mainstream commercial acti¬vity but in rather modest proportions when viewed from the vantage point of world energy needs. But the chain of events wherein it became increasingly obvious that we were in energy trouble irrespective of world politics, spurred alternative energy source activities in the fossil fuels areas. The oil embargo of 1973-1974 made the obvious even more so and provided additional emphasis for the need of such alternatives. Yet the preponderance of these added expenditures and activities (with one notable exception which is the subject of this discussion) has been focused on the intended identification of the best or ultimate process by means of analytical and modest empirical means, whereas our circumstance dictates a bold, higher-risk effort to prove the viability of coal conversion as an industry on a real-time, real-size, real-economics basis. With such proof on hand, industry demands in all related areas will provide the stimulus, motivation and environment for all processes. There is both need and room for many who will compete for a meaningful segment of this new industry which can grow at a rate never seen before in our growth history. The single program in the world today oriented specifically toward the goal of proof of industry viability is the Energy Research and Development Administration's CBF (clean boiler fuels) Program for which COALCON is proud to be the prime contractor.

Jan 1, 1976

By Paul O. Knorr

The Bureau of Ocean Energy Management (BOEM), a bureau within the U.S. Department of the Interior, has responsibility over both energy and non-energy mineral development on the United States Outer Continental Shelf (OCS) under the OCS Lands Act (“OCSLA”). BOEM’s Marine Minerals Program (MMP) manages federal offshore mineral deposits through non-competitive, negotiated agreements for sand and gravel (“sand”) used in coastal restoration efforts and the competitive leasing of critical and hard economic minerals (“critical minerals”). As the steward of OCS critical minerals, BOEM MMP is responsible for understanding where critical minerals are located, identifying and understanding their environments, managing activities that affect these resources, and implementing pertinent federal policies. Fulfilling these responsibilities involves the collection and analysis of environmental, geological, and geophysical data; supporting the science needed to understand the impacts of resourcerelated authorized activities on the biological, physical, and sociocultural environments; encouraging emerging technologies that can reduce the environmental impact of activities; and communicating with stakeholders to foster an understanding of existing federal regulations and potential needs to revise the legal framework. Four U.S. federal rules in the Code of Federal Regulations (CFR) currently inform MMP’s procedures: 30 CFR 580 (prospecting for minerals), 30 CFR 581 (leasing of minerals), 30 CFR 582 (operations in the OCS related to minerals), and 30 CFR 583 (negotiated noncompetitive agreements for sand). Other federal laws and regulations are also pertinent, particularly those supporting the National Environmental Policy Act, Endangered Species Act, National Historic Preservation Act, Marine Mammal Protection Act, Coastal Zone Management Act, Clean Air Act, Federal Water Pollution Control Act, and Magnuson Stevens Fishery Conservation and Management Act.

Feb 22, 2026

By Francois E. Heuze

The mined geologic burial of high-level nuclear waste is how the favored option for disposal. The underground repositories must keep the waste away from the biosphere for very long times - several thousands to tens of thousands of years. Also, access must be maintained to the vaults for several tens of years, so that the waste can be retrieved, if necessary. Both the excavation of the underground chambers, and the radiogenic heating will disturb the rock mass. The overall rock mechanics problem is to understand and predict the processes associated with these perturbations, and their impact oh the isolation and containment of the waste (3)**. The specific rock. mechanics issues which have been identified for the three candidate hard rocks (basalt, granite, and tuff), are summarized in Table 1. The table also indicates the level of adequacy of our knowledge in the areas of the various issues. Such an evaluation is consistent with the general consensus of the rock mechanics profession, as explained in several key reports and publications (1 to 11). The main shortcomings of today's rock mechanics for waste repositories can be summarized as: ? lack of resolution for remote mapping of fractures in rock masses ? great difficulty in testing large volumes of rocks to determine their mechanical properties.

Jan 1, 1981

By A. A. Compoli

Injecting water under pressure to wet the coalbed in advance of mining reduces mining-generated respirable dust. Owing to economic and geological barriers, water infusion for longwall dust control in the United States is currently limited to the Pocahontas No.3 Coalbed in Virginia. Water is pumped into the coalbed through underground boreholes drilled horizontally from the headgate toward the tailgate side of retreat longwall panels. This paper theorizes that the barriers to widespread utilization of water infusion for longwall dust control could be overcome by long-duration, low-pressure water infusion through vertical gob gas boreholes. Currently, 43% of the 72longwall mines in the United States employ vertical gob gas boreholes. Computer coalbed reservoir simulation suggests that one vertical surface borehole could infuse the same longwall panel area as four horizontal boreholes in the current water infusion system for longwall dust control in the Pocahontas No.3 Coalbed.

Jan 1, 1995

By M. Modis

According to previously established theoretical analysis and under certain conditions, a critical sampling grid can be determined for an earth-related space-distributed natural variable. Sampling above this critical limit adds little to the mapping results, while based on this limit the ideal process of reproducing the original phenomenon is theoretically defined. The objective of this paper is the application of the above theory to the Klidi lignite deposit in Florina, Greece, where Public Power Corporation (Greece) has conducted a sampling campaign to estimate the deposit thickness and its heating value. Data acquired for these two variables were analysed in the space domain in order to derive their respective correlation functions. The structural analysis of the deposit generated two covariance models, one for the thickness and one for the heating value, from which the critical sampling grid was identified. The conclusion drawn is that in some parts of the deposit the sampling grid is denser than required. Finally, an optimal sampling grid is proposed in order to gain the maximum information at the lowest cost.

Jan 1, 2006

By Yao Dun-Pu

Solution mining, sometimes also refered to as chemical mining or bacterial mining, is an innovative technology which, by making use of proper chemical reagents and taking advantage of bio-chemical action of some micro-organism species, can dissolve effectively most. desirable metallic values from ores and then extract them profitably from the resultant metal-bearing solution by suitable means to form the metal product it is more preferable to the conventional mining methods, not only because of its capability to improve working conditions and minimize environmental problems either underground or on surface, but also for its amenability in particular, to exploit low-grade or submarginal ore bodies, or those deposits which are too deep-seated to be mined out economically. Furthermore, it also provides a potential approach to win metals directly from their ores or ore-deposits in-situ by more simplified methods and at a lower cast than the conventional mining-milling-smelting process would do previously. Hence, in developing countries such as China, it will most, probably become a new mining tool of great promise. (1)

Jan 1, 1981

By James M. Peay

This paper discusses the recently completed organizational development research project, which was addressed to the underground mining industry. The three specific purposes of the project were as follows: (a) to determine whether Organizational Development approaches are feasible in the mining industry, (b) to provide a demonstration that Organizational Development methods can successfully contribute to the safety of underground mines, and (c) to compare the efficacy of classical Organizational Development methods, which are highly trainer- intensive, with trainer-nonintensive management development approaches. The term "Organizational Development" (OD) is here broadly defined as a management intervention for the purpose of assisting an organization with the solution of problems, which are seen by the organization as important. More specifically, we can define OD as a planned effort to improve the effectiveness of an organization through (a) team building and problem solving, which concentrates on the issues of immediate concern to the organization, and (b) efforts to improve organizational communication at all levels of the organization.

Jan 1, 1983

By C. L. McKenzie

American Girl Mine is located in the Cargo Muchacho Mountains in the southeastern Imperial Valley of Southern California. Production from the current open pit mine and heap leach recovery system began in early 1989. Previous mining and gold recovery took place commencing in 1987 at the Padre Madre site, situated adjacent to the American Girl site to the southwest. In mid-1990, a 790-tonne-per-day underground gold mine and mill went into production. Approximately 6,500 troy ounces of gold per month are recovered from the combined open pit underground mine operation. Copper in the form of Azurite [Cu3(CO3)2(OH)2] and Malachite [Cu2CO3(OH)2] are abundant in the mined ores (Henshaw, 1942). The high solubility of these minerals in caustic cyanide solutions has a negative impact on carbon adsorption and electrowin processes. This paper presents the results of monitoring programs, process chemistry, and control changes introduced at American Girl Mine to abate production complications in the refinery and measures taken to minimize solution gold losses in the adsorption circuit(s).

Jan 1, 1993

By Aurel Goodwin

MSHA is the regulatory Agency which administers the Federal Mine Safety and Health Act. Although MSHA's principles largely derive from this Act, they do not exculsively derive from it. One might expect that our principles are contained in the regulations we have published to implement the Act. To a degree, this is true; but the regulations we have now were developed and published before the current Act became effective. For this reason, as well as others, there are some principles that we support which are not evident in our regulations, or in the Act. One of these is the ALARA principle. This principle requires that all unnecessary exposure be avoided; that is, all exposures should be kept "As Low As Reasonably Achievable." Almost all professionals in radiation control can agree with this broad principle; but it would be difficult to get agreement on a regulation which would translate the principle into industry practice. Rather, our regulations specify a limit to exposure for any individual. For radon daughters the current limit is four working level months per year. By having an explicit limit such as this, the ALARA principle often becomes lost and the limit becomes the goal. The principles contained in the Act are equally broad in scope. The principles apply not only for radiation protection, but also for toxic substances and harmful physical agents. The Act states that standards for such substances or agents shall most adequately assure on the basis of the best available evidence that no miner will suffer material impairment of health or functional capacity, even if such miner has regular exposure to the hazards dealt with for the period of his working life. The Act also provides that, although protection of health must be our foremost concern, other considerations shall be the latest scientific data in the field and the feasibility of the standards. Our regulations reflected similar principles when they were developed and promulgated. From experience with other health and safety laws, Congress realized that setting and meeting an exposure limit may not be sufficient to prevent disease. The Act, therefore, contains a detailed description of additional provisions to be included, where appropriate, in mandatory safety and health standards. One of these additional provisions requires that miners be informed about the nature of the hazards associated with their job and about the means for their own protection. Another provision requires the use of labels and other forms of warning to inform miners about the hazards, about proper precautions for safe use or exposure, about relevant symptoms of overexposure, and about emergency treatment. We have partially implemented these provisions through regulation. The Act requires also that standards shall prescribe protective equipment and control of technological procedures and that they shall provide for the monitoring of miners' exposures. We have implemented this provision to a degree also through regulation. Finally, the Act specifies that, where appropriate, a mandatory standard must prescribe the type and frequency of medical examinations in order to most effectively determine whether the health of miners is adversely affected by exposure. Additionally, when a determination is made that a miner may suffer material impairment of health or functional capacity by reason of exposure, that miner must be removed from such exposure and reassigned. In order to encourage miners to take the medical examination, the Act also provides that the miner shall not suffer loss of pay as a result of being reassigned. This additional provision on medical examinations has not been implemented by regulation for radiation hazards, nor for most other toxic substances or hazardous physical agents. We believe that this conference will provide us with valuable information on medical examinations for radiation exposure, as well as on other considerations to be used in future regulations. We still question whether our basic exposure standard of four working level months per year is adequate to protect a miner's health. This conference is indeed timely because both MSHA and NIOSH have been reviewing this issue for some time. I would like to reemphasize MSHA's commitment to education and training. MSHA strongly believes that miners should be informed fully about the real and potential hazards associated with their work. They should know the nature of the hazard and the means for protecting themselves from the hazard. The Act also emphasizes the need for training miners by requiring that new miners receive 40 hours of training before working underground and 24 hours of training before working on the surface. The Act also requires eight hours of refresher training annually. This training must include information on the relevant health hazards and the potential consequences of overexposure. Before I close, I would like to mention briefly another source of principles that MSHA often consults to obtain guidance for both the development and enforcement of regulations. These are the various court decisions that are handed down from time to time. Two in particular that I want to stress are the recent Supreme Court Decisions on benzene and cotton dust. Although neither of the decisions has a direct impact on mining or radiation, they do clarify some general principles and directions for regulatory agencies, such as the role of cost-benefit analysis and the need for risk assessment. In closing, I wish us all an open exchange of information for a productive and useful conference.

Jan 1, 1981

By James C. Conti

A surface charge sensor has been developed that responds to changes in the double layer properties of colloidal silica during the cationic flotation of silica from taconite ores. Sensor design allows for the measurement of two aspects of the electrical double layer surrounding all solids immersed in ionic solutions. One aspect responds to a flow induced change in the double layer properties of a solid. The other is a function of the chemical composition of the aqueous phase. Evaluation of sensor performance during froth flotation experiments has been encouraging. Process monitoring capabilities are indicated.

Jan 1, 1981

By R. S. Saunders

Congress, under the Nuclear Waste Policy Act of 1982, as amended, charged the U.S. Department of Energy (DOE) with the responsibility for safe and permanent disposal of high-level radioactive waste in a geologic repository. The waste will consist of spent fuel from commercial nuclear generating plants and reprocessing activities. Under direction of this law DOE is currently evaluating Yucca Mountain in Southern Nevada as the candidate site for a potential high-level radioactive waste repository. Presidential, Congressional and State of Nevada approval are needed for repository construction to proceed after successful completion of site characterization and recommendation of the site to Congress. The DOE will submit a license application to the Nuclear Regulatory Commission (NRC) to construct the geologic repository. Following successful construction DOE will update its license application to operate the repository.

Jan 1, 1993

By Raúl Castro, Marco Vera, Alfonso Ovalle

The underground mining evolution for block cave mines in Chile and worldwide has made important strides in the last decades. Nonetheless, reserves determination in the initial stages of these types of projects—mainly for long-term planning—is not studied in as much detail as it should be, especially regarding the impact on the final value of the enterprise. Today, the first estimation of the size of a block cave mine, typically expressed in tons, tends to determine very large footprints and ore bodies. The resulting large-scale mine is obtained by applying the marginal cut-off grade (COG) to determine reserves. Yet, in many cases, it is possible to obtain an equal or higher benefit, extracting fewer reserves in less time, with a smaller active area, which significantly reduces the project’s uncertainty. To explore scenarios obtained by applying a higher marginal COG in the initial phases of the project, the Hill of Value methodology is used to estimate the net present value (NPV) in relation to the production rate and the COG. However, the application of this methodology considers certain simplifications that generate results which are not completely satisfactory in specific cases. This paper suggests an improvement of this method to obtain more reliable results regarding determination of a COG profile that will optimize the NPVof a block-cave project. The methodology was developed and applied in a massive polymetallic deposit with zinc, lead, and silver mineralization, corresponding to a real block caving project. The methodology provides NPV results that differ by approximately 15% in comparison to the real mine plan, while also being considerably simpler and faster to calculate. In summary, the proposed methodology provides a reasonable and fast procedure to estimate higher than marginal COG that increases the NPV of block cave mine projects.

By O. J. R. Baena, N. J. Zapata

In Colombia, more than 15 regions and around 100 municipalities develop gold mining at different scales, and these operations generate mining waste composed of processing fluids and crushed rock with metals and high silica content. Cement production requires clinker, gypsum and other corrective additives. Clinker results from the partial fusion of some minerals including silica. In this study is proposed to evaluate the effect of the use of mining tailings sands from gold mining in the manufacture of clinker. The proposed methodology will allow the characterization of the sands to manufacture a cement specimen and measure its physical and fire properties

Mar 2, 2022

By Bjorn Olsson

"Heavy impact. High frequency hammering. Extreme abrasion. Building on the experience of owning and operating its own mines, Ovako has developed a deep knowledge of how vital the right steel properties are in withstanding the extreme loads encountered in every part of the drill string. That is why Ovako’s product development process is focused on understanding the specific load cases and manufacturing operations associated with rock tools.The punishing conditions of percussive drilling can push the limits of most materials. And heavy mechanical loads are only the beginning. Highimpact energies at high frequency are a major source of fatigue. High temperatures result from impact energy losses. And abrasive, erosive and adhesive wear are constant risks. Handling any of these varying demands at a single point along the drill string is difficult enough — which makes optimizing for the entire drilling system an extremely complex challenge. Engineering for specific loadsOvako has specialized over many decades in analyzing the dominant loads for each of the parts and components used in rock tools, and testing for individual applications in its laboratories. The most critical fatigue properties are controlled through the steel metallurgy, and supported by performance measurements through extensive rotating bending fatigue (RBF) testing, along with special methods that combine impact load with various wear loads. The result is a fit-for-purpose steel with tightly controlled performance properties, making it possible for customers to precalculate the expected life time of their components for highly automated and repetitive processes Tailoring steels for the processing route.The same levels of control and predictability must be carried through to the customer’s own manufacturing processes. By ensuring minimal variations in chemical composition, everything from heat treatment and welding to automated machining can be carried out with high consistency. With precisely controlled material properties based on an existing processing route and exact load case, customers are able to minimize their total tool production costs while ensuring optimal performance for their end products. Development of Hybrid SteelBuilding on this experience in the mining industry, Ovako has developed a new steel family, known as Hybrid Steel, designed to meet the demands of high-stress, elevatedtemperature applications where mechanical and fatigue strength are critical. Traditionally, steels for these applications are produced by expensive small-batch processes. Hybrid Steel, however, enables high volume production at a competitive cost.The world of steel has traditionally been divided into clearly separated categories of tool steel, stainless steel and lower alloy engineering steel. Hybrid Steel is now challenging that division, offering attractive properties from all three categories."

Jan 12, 2017

By Edmund H. Warner

Any city dweller who has walked alone along a remote mine passageway has to be impressed by the eerie silence - the total absence of noise except for ones own breathing and scuffing of boots on the bottom. An underground mine can have tremendous contrasts, from complete silence to the ear piercing clatter of percussion drills working on the mine roof. Noise in underground mining machines is both useful and detrimental. Without characteristic noises that are recognizable to miners, operators would have a more difficult job operating their machines. Noise serves as a warning of approaching machinery, and changes in noise give indication that breakdowns may occur. But excessive noise is a health hazard. In recognition of this fact, our Congress included noise exposure as a part of the "Coal Mine Health and Safety Act of 1969". As Fig. 1 indicates, allowable noise exposure is established by specifying a time duration permitted at different noise levels. This is the well known "Walsh-Healey" criteria which governs noise exposure in many industries.

Jan 1, 1977