Search Documents

By Daniel P. Coughlin, Robert C. Thomas, Christopher S. Romanek, Kristian W. Paul

Two separate constructed treatment wetland (CTW) systems receiving the same metal contaminated, acid sulfate water over different lengths of time and at different rates were evaluated for metal attenuation. Both wetlands are the alkalinity generator portion of a succesive alkalinity producing system (SAPS). Sequential extractions are employed to determine phases of metal removal. Results indicate that Fe, Al, Zn, Ni. and Cu accumulate in the organic substrate over time. Manganese accumulates initially, but is not retained in the system over time.

Jan 1, 2000

By Robert S. Ondrey, Robert A. Haney, David J. Atchison

The Mine Safety and Health Administration has conducted tests to determine the effectiveness of two methods for reducing diesel particulate emissions in underground coal mines. Both methods involved collection of the particulate material before being released into the environment. One method utilized a disposable pleated paper filter attached to the tail pipe; the other utilized a reusable wire mesh screen attached to the tail pipe. This paper describes the instrumentation and testing used to evaluate both control methods. Results of respirable dust and diesel particulate measurements made underground are presented and analyzed.

Jan 1, 1992

By K. N. Han

The adsorption of gold onto activated carbon in iodide solutions was studied. The adsorption rates were determined as a function of temperature, salt concentration and pH, as well as activated carbon concentration. A kinetic model was developed for the adsorption. The adsorption rate was believed to be controlled by a combined mechanism of film diffusion and pore diffusion with the film diffusion having the most significant effect. Experimental findings were in good agreement with the model developed. The apparent activation energy was found to be 14.9 kJ/mol.

Jan 1, 1995

By Dennis Ortega, Rich Kramer

After several operational improvements to FMC's Westvaco Mine Longwall, an ergonomic and operational bottleneck resulted at the mobile belt tail/rigid conveyor junction. Ergonomic hazards, cutting time losses, and spillage problems near the belt tail were identified and targeted for improvement. FMC Westvaco, consulting with FMC Material Handling Division, corrected the bottleneck using an expandable/retractable conveyor system to fill the gap between the mobile belt tail and the rigid conveyor structure. This paper explains the operational expectations, defined before; the challenges, encountered during; and the real outcomes, measured after the installation of an expandable/retractable conveyor system.

Jan 1, 2002

By M. Ghiani, R. Peretti, A. Zucca

The paper deals with the experimental application of a pilot flotation column to baryte and fluorspar ores. The column has been installed in parallel with the cleaning stages of two different industrial flotation plants where the above ores are processed using conventional cells with mechanical impellers. The effect of several parameters, including froth height, wash water additions, pulp feedrate and air supply rate, has been investigated. It has been shown that by finely tuning the above parameters good flotation performances can be achieved. The experimental results demonstrate the greater versatility of the column flotation and its superior separation efficiency, especially for the fine particle size fractions, over conventional cells.

Jan 1, 1995

By James Wm. White

Mine management now recognizes the value of computer-based truck-shovel dispatching in open pit mines. The key tangible benefits are substantial productivity increases with a given fleet of equipment or, alternately, significant reductions in equipment required to meet production quotas. In this work, we review the literature, report on efficient, optimal algorithms for haul truck dispatching in real-time, and briefly discuss methods used by various mines to evaluate productivity improvements over manual methods. We also present actual results obtained at thirteen mining operations around the world.

Jan 1, 1992

By David Jenkins

Grefco Inc. operates two diatomite mines in the western Santa Ynez Mountains. The larger of the two mines, the Palos Colorados Mine, is located approximately seven miles southeast of Lompoc. The Miguelito Mine is located about two miles south of Lompoc on the west side of the Miguelito Canyon. Diatomite from the Palos Colorados and Miguelito mines is trucked to the Grefco plant at Lompoc for processing (Figure 1). HISTORY Grefco, Inc. evolved from the originating Dicalite Company which in 1929 began operations at the Walteria plant in the Palos Verdes Hills south of Los Angeles. In 1942 Dicalite leased the Palos Colorados mine at Lompoc. In 1944 the Dicalite Company was purchased by Great Lakes Carbon Corporation.

Jan 1, 1995

By Peter Keppler, Stephen D. Bundy

"Due diligence" is a review or audit of a facility or business to assess and quantify risks and operating status before an acquisition. Due diligence findings can be used to negotiate the price, general terms, and indemnification provisions in the purchase and sales agreement. In addition to assessing out- standing liabilities, necessary capital improvements, and the adequacy of operating budgets, due diligence should include "nontechnical" considerations, such as local community acceptance and relations, and the effect on the company's public image and operations. This paper will discuss how these considerations can be addressed in the due diligence process and factored into the transaction. Also, innovative means for risk reduction and risk transfer, during and after the transaction, will be discussed.

Jan 1, 2001

By Bryan A. Bartley

About 1,000 machines around the world are breaking rock and hard abrasive materials by a very economic, high intensity, autogenous process, but this method is largely ignored by the mining industry. This vertical shaft autogenous impact crusher has impact velocities around 70 m/s, which compare with those of Cascade and SAG mills of up to 10 m/s. The autogenous impact, breakage processes are all at higher intensity levels and the products reflect this difference. The topic of liberation is breifly considered. A series of tests with a laboratory scale machine are reported to illustrate a number of the characteristics of the process. This paper highlights topics for further evaluation and research.

Jan 1, 1992

By R. J. Sweigard, M. Rohatgi

Differential settlement on reclaimed land presents a particular problem when the land is to be used for row crops. The poorly drained depressions caused by differential settlement restrict crop yield, resulting in additional costs to alleviate the problem. Potentially more serious is the threat of failing to meet target yields due to settlement-related reductions. Because the mechanism by which the problem occurs is not well understood, a physical model study was conducted to investigate the importance of several factors. The importance was considered of such factors as the relative amounts of rock and unconsolidated overburden in the undisturbed condition and the size distribution of rock fragments. But the analysis concentrated on the causes of settlement in the reconstructed soil layer above the rock spoil.

Jan 1, 1991

By D. D. Banerjee, S. K. Kawatra, T. C. Eisele

A high calcium fluidized-bed combustor ash was shown to be an effective binder for iron ore pellets at dosages of 1 % to 2% of the magnetite concentrate weight. Magnetite pellets that were between 1.1 and 12.7 mm (7/16 and 1/2 in.) in diameter were produced with dry crushing strengths greater than 22.3 N (5.0 lb-force) per pellet, which is comparable to the results produced using conventional bentonite binder. The effectiveness of fly-ash-based binders was considerably improved when calcium chloride was added as an accelerator. The addition of calcium chloride at a rate of 0.1 % to 0.2 % of the total powder weight increased the strength of the dried pellets by as much as 22 % compared to the strength of pellets made using fly-ash without accelerators.

Jan 1, 1999

There has been some confusion over the selection of discount rates when performing stochastic simulations of a project's net present value (NPV) using risk- adjusted discounting techniques. Some argue that lower discount rates should be used when performing stochastic valuation simulations. This creates higher NPV values and improves the attractiveness of a project. Others argue that the discount rate should not be lowered for these simulations. This paper exposes the source of this confusion. It demonstrates that stochastic simulations do not remove the risk inherent in a project and, therefore-do not improve a project's value to the risk-averse investor. Risk-adjusted discount rates should, therefore, not be adjusted downward when performing stochastic NPV simulations. Stochastic simulations are, however, shown to he useful in several aspects of project valuation.

Jan 1, 1996

By M. Rossi

The use of service variables in geostatistics (grade-thickness) is common in industry when developing block grade models and geologic resource estimates. This is particularly true in the case of sedimentary and stratabound-type deposits. The approach has proven merits when assessing ore reserves. However, there are cases where its application for preliminary data analysis produces biased estimates. One such case is encountered in uranium disequilibrium studies. This paper demonstrates the inadequacy of service variables when performing uranium disequilibrium studies. Disequilibrium analysis is a necessary preprocessing step when radiation counts are used as raw data to calculate uranium reserves. Typically, a probe is used to obtain the gamma counts from open drill holes. These counts are then regressed (and corrected) against chemical assays obtained from core samples. During this process the grade-thickness variable produces an optimistic image of the relationship between probe grades and chemical (true) grades, causing overestimation of the final geologic resource. The problem is analyzed through a case study.

Jan 1, 1993

At present, increasing focus of public perception is placed on the environmental and social benefits, risks and impacts of metals and metal-bearing products. To address these issues, the concept of product stewardship has recently been introduced into the political debate. In this paper, results from a survey of existing environmental and social reporting practice in the copper mining, smelting, refining and fabricating industry are presented. In this context, particular emphasis is placed on the reporting practice regarding products and product performance over the life cycle. In a few companies there has recently been a shift towards adopting product stewardship principles and putting them into action. As part of an ongoing exercise within the Non-Ferrous Consultative Forum on Sustainable Development sponsored by the International Copper Study Group (ICSG) key issues of interest to the non-ferrous metals sector are being addressed. The Forum, for example, has developed a series of principles, criteria and indicators that could form the basis for a voluntary, industry-lead product stewardship scheme. Current achievements and way forward of this product stewardship initiative will be presented.

Jan 1, 2003

By Bekta? Uz

In this research, geological characteristics of sand quarries around the village, Kemerburgaz Akpinar, are studied and the mineralogical, petrographical, chemical and technological characteristics (such as sieve analysis, relative density, water absorbtion etc.) of the sand samples, obtained from the area are explained. In the general area sand' quarries, being in lacustrine formations belonging to Neogen, the stratigraphic location of the sand occurences take place at high levels of these formations, geologically. All of this pattern, being under 1 mm with a ,particle dimension, it ranges from 0,5 mm in the quantity of 99 % to 0,25 mm in the quantity of 15 relative density is 2,65 g/cm3 ; water absorbtion is 0,9%. Mineralogically, the sand samples contain Quartz (84%), Feldspar (3%), Calcite + Aragonite (10%), Pyroxen+Amphibole (1-2%), Garnet+Tourmaline (0.5%), Olivine (0.1-0.5%). Besides, sand samples contain SiO2 with the quantity of above 90%. Containing Quartz at high levels for mineralogical, petrographical and chemical characteristics, Akpinar sand will be evaluated as silica sand when the carbonate mineral is removed with the method of ore preparation such as leaching.

Jan 1, 2005

By C. R. Bennett

A copper heap leach model, employing leading edge computational fluid dynamics (CFD) technology, is applied to the Zaldivar heap leach operation in Chile in order to explore and analyze the possible impact of operational changes. The effect of changes to the heap operation on copper recovery has been previously investigated and reported by the Zaldivar operation. This paper examines the extent to which a comprehensive heap leach model supports the analysis and conclusions of the published work. The heap is a complex multi-phase process, consisting of a solid static porous media with complex fluid flow, gas and liquid phases, competing solid-liquid reactions, dissolution of minerals and transport through the heap. The model accounts for the physical and chemical features of the heap, including transport and reactions kinetics for the important copper and iron sulfide minerals, ferrous oxidation, bacterial effects, thermal energy, acid and sulfate balances. The model was calibrated to published data on the ore body and employed to analyze the impact of a number of operational changes, including solution flow rate, acidity, lift height, crush size and head grade.

Jan 1, 2012

By Sharon Thomson

Since 1977, Amax Coal Co.'s Belle Ayr mine near Gillette, WY, has been the largest producing coal mine in the US. In its 10 years of operation more than 90 Mt (100 million st) of coal have been shipped from the mine's facilities to electric generating plants across the country. It is thought to be the largest amount ever produced in US history from a single coal mine. The railroad is Belle Ayr's lifeline for moving this massive volume from a relatively isolated corner of northeastern Wyoming. There are no waterways for barge traffic, and highway truck hauling would be impractical considering the quantity and distance of coal to be moved. Transportation in the Powder River Basin-at least for the present-is strictly unit trains. An average of four unit trains daily load at Belle Ayr. These trains average 108 cars long, with a capacity of 91 t (100 st) per car. Burlington Northern Railroad serves the Powder River Basin, but locomotives supplied by Union Pacific, Milwaukee Road, and Kansas City Southern are a common site as well, since coal will often travel these lines too on its way to utility plants in Colorado, Kansas, Iowa, Texas, Arkansas, Louisiana, Wisconsin, and Oregon. When Belle Ayr opened transportation in the Powder River Basin was in an early development stage. As the first large-scale coal shipper in the area, Belle Ayr was the only user of a 27-km (17-mile) railroad spur south of Gillette. Other mines, however, were to open soon on the abundant, low-sulfur reserves. Today, less than a decade after Belle Ayr's debut, 13 large-capacity mines operate near Gillette. The 27-km (17-mile) spur that once served only Belle Ayr has been extended 177 km (110 miles) south to service other mines as well, and to tie into a major rail line in central Wyoming. The Powder River Basin is now served by a wishbone-shaped track configuration that allows train movement north into Montana, south into Colorado, and east into Nebraska for connections across the country. Operations at Belle Ayr are closely tied to train arrivals and departures, with coordination essential between mine operations and rail personnel. "Train movement in the Powder River Basin has evolved to the point where we are fine-tuning mining operations to coordinate them with a more dependable transportation system," according to Joe Jefferson, transportation supervisor with Amax Coal's western division. That, however, hasn't always

Jan 10, 1982

By William E. Wallace, Michael J. Keane

This review summarizes three sets of ongoing studies which we are performing in collaboration with a number of researchers associated with the Dept. of Interior - Generic Mineral Technology Center for the Study of Respirable Dusts, concerning surfactant-particle interactions studied using this surrogate surfactant. These topics are: (A) the suppression of mineral particle cytotoxic potential by DPL adsorption and the persistence of this effect under conditions of enzymatic digestion; (B) surfactant suppression of organic particle cytotoxicity by DPL adsorption and the effect on subsequent expression of genotoxic potential; (C) potential effects of surfactant on heterogeneous structured complex respirable particles. The references list some of our reports which can provide additional information on these studies. Further, those reports provide references to the literature of the field and to the works of others on these topics. Deep lung airspaces, the pulmonary alveoli and respiratory bronchioles, are coated with a hypophase which is rich in surfactant biomolecules secreted by the alveolar type II epithelial cells. The surfactant is known to be critical to maintaining stable low surface tensions on the inner surfaces of the alveoli by forming a surfactant layer on the airliquid interface of the alveolar hypophase. Upon deposition in the acinar regions of the lung a respired particle's initial contact will be with this surfactant coating over pulmonary tissue. A primary component of this surfactant is the phospholipid diacyl glycerophosphorylcholine, commonly called lecithin. A surface layer of dipalmitoly lecithin on saline will act much as full pulmonary surfactant in decreasing surface tension and producing a hysteresis in surface tension behavior with surface area. We have used dipalmitoyl glycerophosphorylcholine, or dipalmitoyl lecithin (DPL), a major component of that surfactant, dispersed in physiologic saline as a surrogate for studying interactions of both mineral and organic respirable particles with pulmonary surfactant and consequent effects on particle toxic behavior. A. DUST CYTOTOXICITY AND LECITHIN SURFACTANT ADSORPTION Respirable quartz and kaolin clay particles are found to be comparably cytotoxic in a number of in vitro bioassays including lavaged rat pulmonary macrophage release of cytosolic and lysosomal enzymes, and red blood cell hemolysis as a measure of dust membranolytic potential. These direct and prompt cytotoxic activities do not account for the distinctly greater potential for quartz to induce pulmonary disease. When respirable quartz and kaolin are incubated with a dispersion of DPL in saline at 37C it is found that the prompt cytotoxicity of both dusts is fully suppressed as measured in vitro by pulmonary macrophage release of lactate dehydrogenase, beta-N-

Jan 1, 1991

By B. A. Carbon

Western Australia is the largest state in Australia with an area one and three quarter times the size of Texas. Most of the State is desert or semi-desert, and only the southwest corner is heavily populated. The State has a population of one and a half million people, and one million of these live in and around the city of Perth. Perth is located on the narrow Swan Coastal Plain and is flanked by the Indian Ocean and the Darling Plateau. The Darling Plateau is an ancient peneplain rising some 300 metres above sea level, and forms an important resource base for the population. The Darling Plateau is old, having been formed some 200 million years ago, and its soils are deeply weathered. The parent materials were granite and gneis which have broken down to form lateritic gravels, overlying dense kaolinitic clays. Some 30 million years ago, in the Tertiary period, a sub - tropical climate prevailed. Appropriate conditions of moisture, temperature and drainage led to extensive laterisation. Some of the laterite contains bauxite of mineable quality. Some 1.9 million hectares of the south-west of Western Australia is covered by eucalypt forests. Threequarters of this forest is referred to as "Jarrah

Jan 1, 1984

By Paul L. Russell, Charles O. Hook

While the oil shale resources of the US are becoming increasingly known, few people in this country are aware of the extensive worldwide occurrence of this resource. Two recent international conferences* confirmed the growing worldwide interest in oil shales, both as future and current energy sources. The 1981 conference noted the difficulty in characterizing worldwide oil shale resources because of lack of common terminology in reporting both assay value and resource potential. Assay value is variously reported as: •US gallons per short ton; •Imperial gallons per metric ton; •Liters per metric ton; •Liters per cubic meter; •Weight percent oil; and •Volume percent oil. Oil shale resources are variously reported in barrels, short tons of oil shale, metric tons of oil shale, and cubic meters of shale oil. Worldwide petroleum shortages sparked interest in alternate energy resources including oil shales. While petroleum supplies appear to have stabilized, at least for a while, high costs are affecting the balance of payment index of many countries, resulting in a continued search for local energy resources. Kerogen is the organic constituent of oil shale and may be the most abundant form of hydrocarbon on earth, possibly exceeding coal occurrences and far more abundant than naturally-occurring petroleum resources. Oil shale, by one name or another, is widespread and is known to exist in more than 38 countries (Table 1). Oil shale industries have existed in at least 14 countries at one time or another. Many predated the Drake oil discovery in Pennsylvania in 1859, and most were unable to compete with natural oil; these operations either converted to its use or closed. At the present time shale oil is being produced on a commercial scale only in the USSR and in China. Only very rough estimates of grade and quantity are available for most of the worldwide shale occurrences since only a few deposits have been thoroughly explored. The Green River Formation of Colorado, Utah, and Wyoming is an exception. For many years this oil shale deposit has been described as the largest single concentration of hydrocarbon material in the world. With increasing world interest, larger deposits may yet be found. In 1965, the US Geological Survey published an in-place world oil shale estimate. This study, while made some 16 years ago, is still a reasonable order-of-magnitude estimate. Although exploration and evaluation are underway and a few oil shale deposits have been appraised, information on which to evaluate most worldwide oil shale occurrences has improved little since 1965. Table 2 presents an order-ofmagnitude estimate of in-place world oil shale resources. Total US resources and Green River Formation

Jan 1, 1982