Search Documents

By Betty L. Gibbs

Mine planning and scheduling done with computer programs is possible only after extensive work has been completed to define the geologic extent of an ore body and an overall mine design. Mine planning methodology on computer can vary from computerized engineering tasks through systems which completely optimize a plan with little input from an engineer during the actual scheduling process. However, a strong emphasis is placed on producing practical mining sequences which may be "best" rather than "optimum". This section offers several viewpoints on the planning process using computers. Interactive planning and scheduling systems are attractive for many companies because they are easy for engineers to understand, and the results are acceptable. The engineer develops an open pit mine sequence by trial and error using interactive graphics. The results of this approach can usually be improved. A computer program can help an engineer make many trials in a short time period and provide a higher level of confidence that a "best" plan has been generated.

Jan 1, 1989

By Rudy Rogers

Gas hydrates have unique properties of storing selective gases. As much as 180 volumes of gas (standard conditions) per volume of hydrates may be stored. Recognizing the need for natural gas storage near electrical power plants for peak load use, DOE funded our laboratory to investigate gas hydrates as an economically viable storage means. Our developed process forms hydrates and self-packs the hydrates by only maintaining the gas pressure above a surfactant/water solution while hydrates form and self-pack. The laboratory process was scaled-up and demonstrated storage of 5300 scf of natural gas in hydrates. Subsequent to the demonstration, we discovered preparation procedures whereby laboratory gas hydrates could be stored at 1-atm with less than 1% decomposition over multiple days. The paper will discuss how these two advancements offer potential ways to recover vent gases as well as released hydrate gases from the seafloor. Keywords: gas hydrates, methane storage, surfactants, hydrate stability

Jan 1, 2008

By R. Lee Wooten, Marco D. Boscardin, James M. Taylor

An earth pressure balance (EPB) tunnel boring machine (TBM) and pipe jacking were used to construct a 430-meter-long segment of sanitary sewer force main. The force main was constructed by first jacking a 2045-mm-outside-diameter, reinforced concrete cylinder pipe (RCCP) casing through alluvial sands and gravels. Later, a 1220-mm-diameter, ductile iron carrier pipe was installed within the casing pipe. The main concern affecting the construction method selection was the elimination of the need for dewatering, which could cause groundwater flow from deeper, contaminated sands up across a silt aquitard into cleaner, shallower sands. In addition, the method selected reduced the volume of soil to be handled and, consequentially, the potential amount of contaminated soil to be managed. Items discussed in the paper include provisions for handling boulders and controlling ground movements as excavation and jacking occurred approximately 300 mm beneath an active,4800 kPa, 254-mm-diameter natural gas transmission pipeline.

Jan 1, 1997

By Brendan Parker, Joseph Skrypniuk

Boddington Gold Mine1 (BGM) commenced production in 1987 and is currently ranked as the second largest gold producer in Australia. In a strategy to improve plant efficiency, constraints to plant performance were identified and prioritised with a view to maximising benefit for minimal expenditure. After identifying that leach kinetics and circuit residence time were major constraints, the introduction of oxygen was identified as having the greatest potential for the delivery of sig­nificant cost benefits. The application of oxygen, initially by conventional tech­niques, and subsequently by installation of Atomaer's Filblast gas shear reactor, improved gold recovery, reduced the resi­dence time constraint and enabled higher mill throughput to be achieved. Additional benefits included operation at lower pulp densities and a reduction in reagent usage. A significant reduc­tion in unit operating cost resulted from these benefits. This paper quantifies the above benefits in a format accept­able to both metallurgists and accountants by integrating the findings in a techno-economic perspective.

Jan 1, 1996

By C. H. Bucknam, S. A. Wilson, G. E. McClelland

The Meteoric Water Mobility Procedure (MWMP) was developed in the State of Nevada during the 1980’s as part of their mine waste characterization programs. During the 1990’s the Waste Subcommittee of the Nevada Mining Association (NvMA) contacted ASTM Subcommittee E01.02 on Ores, Concentrates and Related Metallurgical Materials to undertake a standardization program for the method. A cooperative program was developed in conjunction with the Acid Drainage Technology Metal Mining Sector (ADTI-MMS)Prediction Committee, which involved eight of the NvMA labs performing duplicate leaching tests on two test materials: a coarse fraction of the USGS Hard Rock Mine Waste standard and a typical spoils sample from a heap leach operation undergoing closure in Nevada. Solutions for metals analysis were preserved and sent to the USGS Laboratories in Denver to determine the reproducibility and repeatability of the leaching. The history of the method and reference material and the results of the interlaboratory testing and statistical analyses will be presented.

Jan 1, 2003

By Roger Mourich

As the Powder River Basin coal industry has grown, many changes have occurred in the coal market, the economy and the Basin's methods of dealing with competition in the coal mining business. This article notes the mines that have changed to draglines as the major overburden-stripping tool. The Powder River Basin is defined as those mines within a 97 km (60 mile) radius of Gillette, WY. Mines to the north and south of this area - Decker, Spring Creek, Glenrock - have used draglines more extensively. The reasons for the conversions to draglines at each mine, and the specific timing of these changes, were different. However, the driving factor was economics. As coal production increases, strip ratios increase and coal sales prices decrease, mines must find ways to deal with rising costs and falling revenues. The primary method used has been conversion of overburden stripping to dragline operations. Stripping ratio equals the bank cubic yards of overburden removed for every ton of coal mined.

Jan 1, 1994

By E. Simoncini, S. Ulgiati, M. Raugei

A thorough Life Cycle Assessment of ilmenite extraction and processing to yield synthetic rutile (ERMS/EARS process) was performed according to ISO norms 14040 and updates. The LCA includes the parallel application of selected environmental impact assessment methods (as illustrated in Ulgiati et al. [1]), the results of which are compared and discussed. A MI value of 16 kg of abiotic matter per kg of output rutile is calculated, which is largely determined by the amount of coal that is employed in the reduction and drying steps. The Gross Energy Requirement is 3.33 * 107 MJ/kg, a value which we found to be comparable with that previously calculated by us for alumina. Finally, the increase factor of the Emergy Intensity from the raw mineral to the marketed rutile is 3.19, which points to a comparatively medium-low requirement for indirect environmental support. GWP and AP were calculated to be respectively 1.89 kg(CO2eq)/kg and 12.7 g(SO2eq)/kg.

Jan 1, 2005

I was very interested in Professor Park's data on subsidence over longwall panels. His paragraph labeled "Conclusion," however, does not seem appropriate for the article. Nothing in the article gives any discussion of how knowledge of subsidence characteristics can be used in mine design to minimize damage. That thought may have been a reason for undertaking this study, but not a conclusion of it. From his article, I would conclude that subsidence movements last considerably longer at great depth. And the National Coal Board's subsidence prediction model represents this area reasonably accurately, though most literature claims their model predicts far greater disturbances than actually occur in most areas of the United States. Also, I would like to know, is the method used to determine angle of draw? The criterion used can make a significant difference in the value obtained. With 30 m (100 ft) spacing and a 122-m (400-ft) depth the angle between stations can be up to 14°.

Jan 1, 1989

By Lothar Baumann, Wilhelm Knickmeyer

In mechanized roadheading predominantly two methods of rock breakage are applied at present: the cutting method by means of picks and the cutting/crushing method by means of roller cutters. Both systems meanwhile reached a high degree of technical development and consequently show very few possibilities of further improvement. While application of hard-metal picks is limited by rock hardness, the roller cutters require a high specific thrust, and, accordingly, heavy carrier systems. Roller-cutter equipped tunneling machines are therefore only cost-effective in hard-coal mining if the high investments for transport and assembly are justified by a corresponding length of road to be headed. The limit for acceptable cost-effectiveness is at present a minimum heading length of approximately 3 km. In order to improve the specific cutting performance of roller cutters by activation, Bergbau-Forschung carried out a research project sponsored by the Commission of the European Communities and the provincial government of

Jan 1, 1981

By A. G. Sciulli, G. P. Ballock, G. Hearnshaw, K. K. Wu

Waste disposal underground is the most effective method when viewed from an environmental aspect. As costs of other methods of disposal continue to escalate, the cost effectiveness of underground disposal during the mining cycle becomes increasingly attractive. The use of concrete for sealing abandoned mines has proved to be suspect when associated with a relatively incompetent adjacent strata due to its shrinkage characteristics. Complete failure of the plug has been known to occur in some instances. A more effective, cost competitive seal can be obtained using pneumatically stowed material and incorporating a polyurethane grout, which has greater adhesion characteristics than concrete. Injection of the surrounding strata and of the stowed material helps to ensure an impervious barrier and prevent the plug from moving when subject to high pressure heads. When properly placed, impervious seals cause the old workings to flood, raise the mine pool level, and thus eventually eliminate the potential for oxidation, which is the primary cause of acidity in the water

Jan 1, 1987

By G. B. Johnston

I was very interested in Professor Park's data on subsidence over longwall panels. His paragraph labeled "Conclusion," however, does not seem appropriate for the article. Nothing in the article gives any discussion of how knowledge of subsidence characteristics can be used in mine design to minimize damage. That thought may have been a reason for undertaking this study, but not a conclusion of it. From his article, I would conclude that subsidence movements last considerably longer at great depth. And the National Coal Board's subsidence prediction model represents this area reasonably accurately, though most literature claims their model predicts far greater disturbances than actually occur in most areas of the United States. Also, I would like to know, is the method used to determine angle of draw? The criterion used can make a significant difference in the value obtained. With 30 m (100 ft) spacing and a 122-m (400-ft) depth the angle between stations can be up to 14°.

Jan 1, 1990

By Robert L. Bates

United States production of the industrial minerals, ahead of that of the metals since 1946, has shown a steady and rapid growth. By 1963, their value was more than twice that of the metals. Yet papers on the metallic ores continue to dominate the meetings of the Society of Economic Geologists and constitute nearly nine-tenths of the lead papers in Economic Geology. Most of the geological communication that does take place concerning the industrial minerals deals with high-value special-purpose minerals, which are comparable to the metallic ores in geologic complexity. The large-bulk rock products, which are growing fastest in production value, are characterized by relatively simple geology and by thousands of small producing firms, many of which do little or no geological work. The need for geological advice by this very large segment of the industry is bound to increase. In the meantime, a plea is made for more geological communication among those concerned with the industrial minerals of all varieties.

Jan 1, 1966

By D. R. Barker

The economic performance and competitiveness of a concentrator are dependent on the production of accurate real-time assay information and the manner in which it is utilized. Our paper describes the relative merits of on-and in-stream analysis techniques and the economic significance of Assay-Based control and Target Oriented Display Systems. At Outokumpu's pyhasalmi Concentrator, a Flotation Expert Display System aids the process operator to make better decisions and provides guidance on the most efficient method of achieving the desired control objectives.

Jan 1, 1989

By S. F. Walsh

The San Manuel Oxide Pit is located within the subsidence boundaries of Magma Copper Company's block caving operation. Ground conditions offer a constant blasting challenge and vary from hard, competent crystalline rock to widely spaced fracturing in a sedimentary conglomerate. A successful drilling and blasting program has undergone several changes since mining commenced in 1985 and continues to be developed. This paper discusses the site specific progress made with the drilling and blasting program from selection of feasibility parameters to current practice. Topics discussed include controlled blasting, use Of high energy blasting agents, charge decking, blast casting, as well as standard drill and blast techniques.

Jan 1, 1988

By J. P. McDonnell, L. A. Beckett, K. Y. Hammy

Dangerously high stress areas can be controlled by proper mine planning and/or destressing. This paper reviews practical methods to detect and destress high-stress zones along coal faces. The US Bureau of Mines investigated stress-related burst problems and destressing efforts at a cooperating mine. Laboratory tests of the drilling yield method for high stress detection were conducted to determine the correlation between the volume of cuttings obtained and the magnitude of the applied stress. A three- dimemiom1 computer modeling program was used to evaluate the effectiveness of stress relief methods.

Jan 1, 1987

By Malcolm J. McPherson

There have been numerous recorded cases of mine explosions being initiated by falls of roof. The actual mechanism of the ignition has often been unknown. One possibility is incendive frictional sparking, particularly when the falling rock contains quartz. Another possibility that has received little attention is the increase in temperature of the air due to adiabatic compression under the falling roof. This paper analyses that possibility and concludes that falls which are extensive in plan area but not necessarily of great thickness of falling rock can, indeed, produce temperatures in excess of those required for the ignition of coal dust or methane.

Jan 1, 1995

By R. Sawyer, M. Sadler, M. Holdworth

Greens Creek is a high grade Ag/Au/Pb/Zn deposit located in southeast Alaska. Maximizing the Net Smelter Return revenue from the fine grained mineralization is a dynamic process given changes in metal prices, smelting terms, ore grades and flotation characteristics. This paper discusses the evolving concentrate production strategy, and how it is affected by such factors as ore and concentrate specifications and by market conditions. Also described is the development of an on-line computer program that provides the mill operators with real time NSR data and a means for optimizing Net Smelter Return.

Jan 1, 2002

By Carol Cox Russell

More than two thousand abandoned mines within the Animas watershed in Southwestern Colorado are being prioritized for remediation by the Animas River Stakeholders Group (ARSG). Phased collection and assessment of information progressed from large scale to site specific. Prioritization was based on existing or potential environmental impact and technical feasibility of remediation as measured by dissolved Cd, Cu, and/or Zn in the discharge; indicators of habitat degradation; aquatic life in streams; cumulative impacts at the point of compliance; cost effectiveness; treatiblity/feasibility; and cultural and historic preservation.

Jan 1, 2000

By R. L. Pozzo, I. Iwasaki

A previous investigation showed that corrosion currents estimated from polarization curves for the pyrrhotite-grinding media system under abrasion correlated well with corrosion currents estimated from marked ball wear test data by applying Faraday's law. Freshly abraded metal debris were magnetically attracted to pyrrhotite and lowered the rest potentials of the mineral particles, thereby affecting the corrosive wear. The investigation was extended to explore the interactions between a non- magnetic sulfide mineral, pyrite, and abraded metal debris and their effects on the corrosive wear mechanism. The electrochemical behavior of a three-

Jan 1, 1988

By Dave Willis

In ME'S 1994 Powder River Basin (PRB) coal transportation article, the lead author described some destinations pursued by the railroads. As with many destinations, though, they turned out to be merely stops on the way to places that have yet to be reached. Along the way, the railroads discovered that making it better is a continuous process, not just something done in several phases. This was always known but not at the awareness level that exists in 1998 railroad environments. This update of the 1994 article includes railroad companies' plans for the future of rail transportation in the PRB.

Jan 1, 1998