Search Documents

By G. Bräuner

The methods of burst control treated in the authors' very informative paper have been applied in the Ruhr Coalfield, Germany, for more than 20 years and have proved to be highly effective. It might be interesting here to mention a few experiences: • The symptoms of critical stresses when drilling with small diameters ("test drilling") are essentially the same as described. However, we consider the situation safe if these symptoms occur beyond a certain distance ahead of the face. • That safety distance equals three times the seam thickness plus the daily advance. It is the total seam thickness that counts, not merely the mined portion. • Critical stresses within the safety distance are dissolved by so-called destressing measures: drilling with heavier equip¬ment, blasting, or water infusion. • To avoid bump initiation, the destressing operations should begin at the sides of the stressed zone rather than in the middle. • As to water injection, there are two different principles. If the situation is critical already, high pressures are applied for hydraulic fracturing. If the stresses still allow to drill deep holes, the fluid pressure is kept low and acts for a longer time. This is to make the coal break successively instead of violently - a long-term precaution. • When the stresses are very high, destressing is the most appropriate means. We mostly drill with 95 mm-diam (3.7 in. - diam). The techniques in detail are somewhat complex and sub¬ject to modifications. But the general idea is to accomplish burst prevention by controlling the potential burst situations.

Jan 1, 1989

By James J. Brady

The basic story at Bear Swamp was how to excavate an underground chamber 79 feet wide by 227 feet long and 150 feet high, along with the related access, tarbrace, leads, power tunnels and shafts, do it under cost and ahead of schedule and still have just about everybody love you. The isometric sketch of the overall project follows. I won't go into any of the details of the physical scope at this point. Instead, we'll bring out the sizes, grades, particular problems of the different areas as we cover them. First of all, let's establish that Bear Swamp was a Target Estimate - Fee with Incentives type of contract. Gates and Fox's contract was with the project's general contractor, J. A. Jones. We were one of three contractors who submitted proposals and estimates to Jones. After much negotiation and many submittals, Gates and Fox was notified we had been selected to do the underground excavation on April 12, 1971. We had our first people back on site in two days, set up a temporary office, made our first steel order for jumbo erection, pacing our jumbo construction to meet the date when J. A. Jones would have the access portal ready for us. The shops, yards, dry house, compressor building were all erected as sites were designated for our use. At last, on Thursday, June 3, we trimmed the face and moved our 9-machine Euclid jumbo up a hastily constructed haul road and started our portal preparation of the access tunnel.

Jan 1, 1974

By P. Jacquin

Many a deposit estimation has been carried out since geostatistical methods were first implemented. To date however few mining programs have totally been completed and even fewer comparisons can be drawn between estimated reserves and extracted ore tonnages. Aluminium Pechiney work a number of bauxite mines in Southern France. As from 1969 they modified their deposit estimation methods, giving up traditional approaches and opting for geostatistics. At that time, the authors of this paper were entrusted with the first geostatistical estimations and in particular, those concerning the deposits mentioned herein. Over the past decade a number of deposits have been worked out and we thought it interesting to report about comparative results. French bauxite deposits are of the karstic, as opposed to the lateritic, type. The bauxite, formed at some distance of the present-day deposit, was brought to and trapped in limestone karst pits. Subsequent physical and chemical alterations may have taken place : silica and carbonate drifts, recent karst slips. The morphology of these deposits is often rather complicated. The deposits are small from a few hundred thousand to a few million tons at the most. The overburden thickness usually precludes open mining. Mining investments and financial risks are often high, making it necessary to obtain optimal information on the deposit considered for mining. For the three cases brought up in this paper, deposit sizes, exploration methods and conclusions differ. They are brought up mainly to show the advantages inherent to a quality geostatistical study and the lessons drawn by Aluminium Pechiney.

Jan 1, 1982

By P. F. Hara, O&apos

Stratabound Proterozoic precious metal mineralization in central Arizona is associated with felsic and adnesitic to mafic volcanic rocks and sediments derived from these rocks. Hydrothermal fluids associated with felsic volcanism form gold mineralization within hotspring vent complexes or within asymetric basins, which flank the vent complexes and are filled with tuffaceous sediments. Massive to semi-massive sulfide copper-zinc systems associated with felsic volcanism may locally contain small gold occurances either laterally or vertically zoned from the ore. In andesitio to mafic rocks, zinc-lead-gold-silver-copper bearing mineralization and gold mineralization are both associated with feruginous sulfide bearing cherts. The partitioning of gold into these specific geologic environments may be related to variations in temperature and composition of the hydrothermal fluid and the depth of the seawater-sediment interface below sea level during the mineralization event.

Jan 1, 1988

By D. J. Collins

While the charcoal in pulp (CIP) process was introduced to the mining industry many years earlier, it did not gain widespread recognition until 1973 when Homes take Mining Company installed a CIP circuit at their Lead, South Dakota plant. Since then, a number of mills have been put into production which utilizes activated charcoal for the recovery of precious metals. One of these plants was the Jerritt Canyon mill which Freeport Gold Company commissioned in 1981. It was during the time that the author was employed by Freeport Gold Company that the ideas and concepts presented in this paper were formulated.

Jan 1, 1989

By B. P. Boisen

INTRODUCTION The rapidity of onset, rate of increase, and magni¬tude of loads in an underground support system can be measured using load cells or pressure cells, whichever is appropriate to the type of support. These instruments should be installed at the various instrumented station locations immediately after excavation. If the loading of a member is of interest, the load should be measured, whereas if the deflection or strain of a member is of interest, the strain should be mea¬sured. It makes as little sense to use a load cell to allow computation of strain as it does to measure the strain and then back calculate the load. Tunnel steel set de¬signers today invariably rely on the early work of Karl Terzaghi, the basis for which is load, so load measure¬ment should be the main concern. The current trend of using strain gages on steel sup¬port systems stems from the inability by some to eval¬uate unusual loading conditions caused by uneven block¬ing. In fact, uneven blocking will obscure almost any attempt (whether with load cells or strain gages) to properly evaluate support performance. The load curve in Fig. I shows the development of a characteristic early peak load sometimes called the "rear abutment load" seen in many underground open¬ings. It is thought that the peak reflects the coupling of the rock and the support system, and that the magnitude will increase until some yielding, or minor failure, of the support system occurs. At that time, the slight deforma¬tion of the support system promotes the formation of minute shears in the opening walls, and these shears tend to distribute stress between the support system and the adjacent rock in proportion to the relative rigidity of the support elements and the rock. In normal rock, as a result of this stress redistribu¬tion, subsequent load magnitudes generally do not reach the magnitude of the early peak load. In physically unstable (squeezing) or chemically un¬stable (swelling) rock, however, the loads experienced after passage of the early peak load may in fact show a slow, continuous increase. One of the very important purposes of load instrumentation is to provide the means for recognizing such long-term adverse trends, thus enabling the proper remedial steps to be taken. Another purpose of load instrumentation is to pro¬vide a comparison between the magnitudes of the early peak load and the subsequent stable load. The ratio of these two loads is analogous to a safety factor, and may be used to evaluate the efficiency and economy of the support system design. Aside from considerations of economy, it may be well to design support systems which do not have excessively high ratios of early peak load to subsequent stable load. Should these ratios be exces¬sively high, the support system may be so rigid that the yield or failure associated with stress redistribution may occur with explosive violence. Load cells for use in mines, tunnels, and on con¬struction projects come in many forms. Almost all, however, employ the same procedures for installation, readout, etc. Therefore the following comments are almost universal in application. LOAD CELL INSTALLATION Load cells should be installed with bases parallel to the surfaces against which they bear. Care must be taken to orient the cells so that their signal cables are protected from accidental damage as a result of con¬struction, maintenance, or cleanup activities. Most electronic load cells are compensated for tem¬perature variations likely to be encountered during nor¬mal operations. However, if a large difference is an¬ticipated between the calibration temperature [21°C (70°F)] and the average operating temperature, the cells should be conditioned to the operating temperature for at least 8 hr prior to installation. This is to insure that the initial reading, made under no-load conditions prior to installation, provides a stable value to which subse¬quent measurements can be referred. Hydraulic load cells tend to be temperature sensitive and should be used with that in mind. Also, hydraulic load cells tend to be soft compared to electronic types and will sometimes allow movement to take place in a system intended to be semirigid. Furthermore, hydrau¬lic load cells tend to be difficult to read remotely. Care must be taken to use bearing plates on both sides of load cells which are sufficiently rigid and of high enough bearing capacity to prevent bending and crush¬ing under load. This is very important with tieback load cells (basically a ring of steel) which can easily dig into bearing plates. MAINTENANCE AND TROUBLESHOOTING Except for a direct hit by a miner's axe or flyrock from a blast, most hydraulic load cells are nearly in¬destructible and require little, if any, maintenance. Hy¬draulic oil on the bearing plates is a good indication of a leak and the need for corrective action. Field maintenance of electronic load cells involves protecting the instrument and signal cable from mechani¬cal damage and from unnecessary exposure to dirt and moisture, and recognizing and correcting damage and the effects of normal wear and tear.

Jan 1, 1982

By Pierre Ollivier, Dominique Morin

A general study of gold refractory arsenopyrite pyrite concentrate bioleaching has been carried out including two continuous bioleach testworks at different sizes, namely one at a laboratory scale with a 100 1 unit at a 2 kg/d dry solid flowrate and the other at a pilot scale at a 100 kg/d dry solid flowrate. Both tests show a 80% bioleaching of arsenopyrite in about four days of treatment and with the same kinetic. Pyrrhotite is attacked at the earlier stage of the bioleaching but pyrite remains unaffected. The weak potential of oxidation associated with the decomposition of arsenopyrite and the abundance of arsenite leads to a high grade of elemental sulfur in the bioresidue which consumes the major part of the cyanide during the gold recovery, furthermore, the arsenite and ferrous produced in solution have to he oxidized to obtain a stable precipitate in the waste products and as outlined in previous works of other authors on this subject the addition of iron to obtain a Fe/As molar ratio at least above 3 is necessary. The agitation equipment used in the pilot unit allowed an optimisation study calculation for scaling-up the design and power requirements of an industrial installation, For the pretreatment of a gold refractory As high-graded concentrate the reagent cost has the greatest part in the operating cost of the biooxidation step due to the necessary retreatment of the biosolution, In that conditions the power cost is quite marginal, actually it is significant for the treatment of pure pyrite.

Jan 1, 1990

By Thomas J. DeMull

Heap leaching was introduced to the precious metals mining industry approximately two decades ago as a simple, low cost method for recovering gold and silver from ores. Since that time, operational experience has contributed to knowledge and understanding of the process, making it a reliable alternative to conventional milling processes for low grade ores. At time of this writing, dozens of heap leach operations are active producing hundreds of thousands of ounces of gold and millions of ounces of silver annually. These successes have caused the popular press to acclaim heap leaching "high-tech" gold mining, but, despite the hype, the process remains a simple one. An example of simplicity in heap leaching is the operation established in 1986 at Amax Gold's Sleeper Mine. Starting with a simple goal, namely to produce gold from sub-mill grade ore at low cost, heap leaching was rapidly implemented at Sleeper; only five months after testwork started, leaching commenced on the first commercial scale, 50,000 ton heap of low grade ore. Sized at 600,000 tons per year to produce 10,500 oz gold per year, the low grade heap operation has performed beyond expectations. During the first year of production, 881,800 tons have been leached producing 15,665 oz of gold and 35,528 oz of silver. Operating ·costs for the first year have averaged $112 per oz gold produced ( or $95 per oz if silver credit is included). Successful implementation of heap leaching at Sleeper has had a dramatic impact on ore reserves and future operations.

Jan 1, 1998

By A. L. Putz, G. Ladouceur, A. R. Laplante

A laboratory centrifugal concentrator was used to evaluate two gravity circuit configurations treating a flash flotation concentrate at a Canadian gold mill. The Initial circuit consisted of a 76 cm (30 Inch) plant Knelson Concentrator (PKC) for coarse gold removal. Later, a hydroseparator and spiral were Installed, with the hydroseparator underflow feeding the spiral and the spiral tailings plus hydroseparator overfiow reporting to a 51 cm (20 Inch) PKC. Gold recovery In the 76 cm PKC averaged 45%. Gold was recovered consistently In all size fractions greater than 38 µm, where recovery dropped to 22% for the -38 µm material. Changing the circuit to Include the hydroseparator and spiral decreased the Knelson unit recovery to less than 17%. The decrease was attributed to the spiral which recovered much of the free gold ahead of the Knelson and to changes In the mill feed (free gold portions were finer and less abundant). The spiral demonstrated erratic behaviour although It still recovered significant coarse gold (+75 µm) yielding unit recoveries of 18-44%. Although mechanical difficulties were experienced with the 76 cm PKC, Its performance was superior to that of the hydroseparator, spiral and 51 cm PKC configuration. Much of the gold In the ball mill recirculating load was found to be too coarse for significant recovery In the flash flotation cell and should be recovered by gravity from the cyclone underflow or ball mill discharge. The LKC proved to be a successful device to evaluate gravity recoverable gold content. Dilution of test samples with silica further enhanced this methodology.

Jan 1, 1993

By Neil J. Duncan, Edward R. Langfield

A hydraulic rock breaker was developed in Germany by Helmut Darda and uses a wedge-plug and feathers mechanism powered by a 10,000 p.s.i. power pack. During the past four years these tools have been increasingly used all over North America for secondary breaking of boulders and rock. More recently, techniques have been developed to break rock off the solid in trenches and rock emplacements where blasting is pro¬hibited or very limited. Underground operations are commencing to adopt the splitter for scaling plus including systems which can be efficiently applied to chambers and mines. Mr. Neil Duncan, who was originally scheduled to give the main part of this presentation has, during this past month accepted a position with the Alberta Energy Resources Conservation Board in Calgary. The board encourages its members to take part in seminars such as this but, unfortunately, due to the heavy pressure of work, it was impossible for him to attend this conference. Mr. Duncan has, however, forwarded me his notes and suggest¬ions, and using these, combined with a slide presentation, we feel that we can quickly and clearly define the operations and application of the hydraulic splitting technique as it applies to your profession and tunnelling work. The first question that most of you are asking is, "Why use a hydraulic splitter if you can blast?" Our answer to this is that we are not advocating the use of hydraulic splitting where blasting is feasible - but, during the past decade many applica¬tions have arisen where blasting is not allowed, or restricted

Jan 1, 1997

By W. White

The manuscript of this paper was not available for publication when the Proceedings went to press. Should the author elect, he may distribute copies at the time of the Symposium.

Jan 1, 1986

By Ananda M. Wijesinghe

The manuscript of this paper was not available for publication when the Proceedings went to press. Should the author elect, he may distribute copies at the time of the Symposium.

Jan 1, 1986

By Stuart R. Cotterill, Jack D. Nelmark

Introduction Opencast surface mining requires blasthole drilling to achieve mine planning. No single method of mining is right for all conditions. Occasionally, mine planners introduce a project with little regard to drilling and blasting. These costs are usually a significant percentage of total mine overhead. One drilling and blasting method that can be used to reduce overall mine expense is inclined or angle hole drilling. But inclined-hole drilling will not cut costs unless a set of required circumstances is met. Several conditions of mine design indicate the use of angle drilling. Geotechnical problems must first be analyzed. Primary considerations are safety, fragmentation, production, and maintenance. Secondary considerations are, in some instances, reduction in amount of explosives, which lowers blasting costs; reduction of practical fragmentation beyond blasting pattern limits; and reductions in overall costs due to reduced volume of excavation. Future trends in blasthole drilling may include incorporation of drill equipment designed to allow rapid change from vertical to inclined drilling. This will allow the operator to adapt to changing hole requirements with minimal production loss. Another improvement may be the ability to chamber holes at any elevation throughout the hole depth. This will allow more charge to be placed at strategic locations to improve fragmentation. Merits of Drilling Inclined Holes Drilling is performed to create voids for explosives. It is done either to recover minerals or to excavate a volume of earth. The manner of mining or excavation can greatly affect the economics of the overall project. Many innovations and methods have been tried, but the most practical and economical is still drilling holes and using explosives to fragment the material. To break up the material, the practice has been to place charges within the mass. This is done by drilling holes of a specific diameter and depth into the material. The holes are of such magnitude as to develop sufficient energy to break or loosen this material, providing for easier removal. In general, more open or exposed faces must exist to aid material breakage when blasting. Inclined drilling can be advantageous in open-cut mining with highwall depths of at least 24 m (80 ft). A minimum of two faces are open in open-cut mining and the material can be thrown outward to cover pre-mined volume. This cuts cost by eliminating the need to remove or relocate a large portion of material. Sometimes the material is of such a mass that more energy per unit is required to loosen it than can easily be done by blasting vertically. Inclined holes allow a more uniform loading of drilled holes. The unit of energy is raised, so little or no secondary blasting is required. This usually comes about only if the main plan calls for drilling holes deeper than 24 m (80 ft). For shallow holes, spacing and burden can be made closer to allow sufficient energy to blast the toe. If the open face is in only one

Jan 9, 1984

By H. Lyn Bourne

The is the 13th year for this column and the 12th in which the royalty data have been tabulated. There still exist some holes in the list of royalties that readers hopefully will fill. The most common mineral commodity is construction aggregates - either sand and gravel or crushed stone. In spite of their pervasive use nationwide, there are states from which the author has no information about royalties for either of these commodities. The reader can help - share information about these missing states and next year there will be fewer states without information. Severn Brown again sends helpful information from the Prospectors and Developers Association of Canada (PDAC). The PDAC Digest contained an article that distinguished between ‘net smelter return royalty' and ‘net profits royalty’ (Haase). The article also lists clauses and details that Brown suggests should be included in a net profits royalty contract.

Jan 1, 1994

By L. A. Feldkamp, L. I. Davis, F. Yuan, G. V. Puskorius

Emerging technologies such as neural networks and fuzzy logic have many potential industrial applications in diagnostics, modeling, and control. In the automotive industry, applications can be divided into those that impact manufacturing processes and those that relate directly to the product. Though discussion often centers on neural networks deployed in hardware, their potential in the development of problem solutions (however deployed) could easily be of greater importance. Here we concentrate on the use of neural networks for modeling and control, using a simulation of vehicle active suspension as a concrete example.

Jan 1, 1993

By H. L. Bourne

Not everyone understands the concept of mineral royalty. Mineral royalty is a fee paid to a landowner by someone who extracts a mineral commodity from the owners property. The royalty contract between the lessor and lessee contains clauses and conditions that are significant to both parties, e.g., annual m1n1mum, escalation factor, duration of the lease, reclamation and assignability. Comparison of royalty rates requires knowledge of many conditions that influence the value of a given deposit. People in several different professions benefit from shared royalty information.

Jan 1, 1989

By D. C. White

The Vulture Mine near Wickenburg, Arizona was a major gold producer from 1863 to 1942, having yielded about 11,000 kg Au and 8,000 kg Ag. Gold occurs as coarse native metal and electrum in quartz veins and also finely disseminated within a quartz monzonite sill and its silicified wall rock. The sill is semi-conformable within a Proterozoic volcaniclastic-dominated sequence all dipping north about 35°. Early mining focused on the vein-hosted gold particularly in the immediate hanging wall and footwall of the sill. Later efforts included some open-pitting of the outcropping sill and adjacent altered and mineralized rock. Two sets of post-mineral faults have complicated the orebody geometry.

Jan 1, 1988

By David R. Zuchelli, Elio L. . Checca

Two case studies of methane gas explosions and their effect on the operation of underground coal mines are presented. The studies detail the recovery operations and investigations at each mine site. These include the circumstances prior to the explosions and the effects on the surface and underground ventilation control systems. Various ignition sources such as surface and underground electrical power systems, degasification sites, ventilation shafts, test well casings, and lightning activity were investigated. In each case, a lightning report from the National Lightning Detection Network1 was used in conjunction with the physical evidence and eyewitness accounts to confirm lightning strikes as the ignition source for the explosions.

Jan 1, 1995

By David J. Leeds

Increased interest in the utilization of the underground environment for water conveyance tunnels, vehicular tunnels, room and pillar type storage chambers, and military installations has focused attention on the possible effects of seismic activity on the stability of these types of structures. Earthquake experience has generally been related to the seismic stability on the surface of the earth. To establish aseismic design criteria, we attempt to predict the seismic exposure of a given site, both in terms of the spectrum of motion to which the structure must react favorably, and the recurrence rate of that motion. Experience gained from studying the effects of the Plowshare underground nuclear tests on existing tunnels and mines, coupled with the experience of the behavior of tunnels and mines in earthquake regions, provides us with an insight to predict the possible effects of earthquakes on underground openings and to establish design criteria. The type of damage ranges from minor fracturing and movements along pre-existing joints or faults through deformation of openings to collapse. The methods used to establish the seismic design criteria for an underground opening require modification of surface criteria to account for the difference in both amplitude and spectra underground. An aseismic evaluation should be performed on all important projects in areas exposed to possible earthquake motion. To perform this evaluation, information is required pertaining to the geometry and properties of structure and ground. Dynamic as well as static properties are required. A prediction of performance can be derived by exposing a model of the site, expressed in terms of its properties and geometry, to a design earthquake.

Jan 1, 1997

By Terrence D. Chatwin, James Hendrix

Based on the findings within their report to Congress, the US Environmental Protection Agency (EPA) announced that it had decided not to regulate mining wastes under the hazardous waste regulatory program. However, they found that some mining wastes are hazardous and may be causing environmental damage. Cyanide wastes from heap leach operations were included in this group. In evaluating the effects of cyanide use in mining one finds a significant lack of information on the fate of cyanide in soils. Cyanide attenuation and degradation of soils is important, because ground water is a major potential pathway for cyanide contamination. There is a strong potential for cyanide to be removed from solutions as it migrates through soils· by volatilization, chemical reaction, adsorption, oxidation and biological processes, but no definitive investigation has defined these mechanisms adequately to be able to predict the fate of cyanide in soils.

Jan 1, 1998