Search Documents

By Peter J. Huck, Bruce G. Stegman, Richard E. Thill

Introduction Backfilling of mine voids is used to prevent or control the effects of subsidence on surface structures. The pumped-slurry, blind backfilling process has been successful for stabilizing ground over abandoned and inaccessible underground coal mines. This article describes the systematic evaluation of potential monitoring systems that would improve backfill monitoring technology. It also details field proof-of-concept tests that were conducted on two systems and the difficulties encountered in implementing them. Ground subsidence over abandoned mines can have devastating effects on overlying urban areas decades after the closing of room-and-pillar mines. The result may be cracked foundations, ruptured gas and water lines, broken sewers, distortion or cracking in superstructures, and sinks and potholes in the ground surface. About 32,000 km2 (8 million acres) of land in the US has been undermined for coal. According to the US General Accounting Office, 8,100 km2 (2 million acres) have undergone subsidence and another 8,100 km2 (2 million acres) are expected to subside by the year 2000. Actual figures on land affected or threatened by subsidence are probably much higher, since these estimates were based on late 1960s studies. For more than two decades, the US Bureau of Mines has been engaged in stabilizing ground in urban areas having high risk potential for subsidence costing millions of dollars. Thousands of acres have been stabilized, protecting property worth hundreds of millions of dollars. In earlier years, backfilling was by in-mine stowing in accessible mines or by gravity-feed sluicing methods in inaccessible mines. Pumped-slurry methods have been used extensively in the past 10 years. More slurry can be injected for fill from fewer injection holes over extensive areas in abandoned mines. Since this method requires fewer boreholes, there is less disruption of surface facilities. An investigation was conducted to determine the feasibility of using advanced, remote sensing or monitoring technology for application in monitoring fill placement. Specifically, the objective was to develop conceptual systems for blind backfill monitoring that require fewer boreholes and give better definition than is now possible. Blind Backfilling Methods Blind backfilling operations are conducted from the surface and do not require personnel and equipment underground. These methods are applicable to abandoned, inaccessible workings. Two categories of blind back-filling are point support, practiced by civil engineers to protect individual structures or surface facilities, and areal backfilling methods, used to protect large areas against subsidence. Point Support Methods Point support methods are usually gravity-feed systems. In general, point support methods use small volumes of expensive fill material and require a large number of boreholes within a constructed site. Because of the processed material used for back-filling and the close spacing of the injection boreholes, control and monitoring often may be accomplished by borehole cameras. Areal Backfilling Areal backfilling is conducted mainly by the pumped-slurry injection process (Fig. 1). In eastern and interior coalfields, material used is often mine refuse or flyash, both being undesirable on the surface and costly to dispose of in an environmentally acceptable manner. Hence, the use of

Jan 12, 1983

By J. C. Squire, E. W. Baker, G. A. Sullivan, G. W. Flathers

A mine collapse severs communication with trapped miners. Landlines are crushed and commercially available radios cannot penetrate hundreds of feet of dense, conductive earth without the use of regenerative repeaters that may also be crushed. This paper describes a proof-of-concept device that uses seismic P-waves, instead of radio waves, to allow communication of a code that represents prearranged messages, including the safe haven location identifier, number of people and air quality, from trapped miners to aboveground rescue units. The transmitter designed is about 0.03 m3 (1 ft3) in size and can broadcast for four hours from its 27-kg (60-lb) battery pack. The receiver consists of a geophone and a 2.5-kg (5.5- lb) signal conditioning unit attached to a laptop computer, which displays the communication signal in real time. Testing in a bituminous coal mine with an MSHA representative revealed the device was able to transmit through 271 m (890 ft) of overburden, at 0° and 12° from vertical, using 500 W of power.

Jan 1, 2009

By Robert C. White, Kurt W. Keskimaki

The Henderson Mine is a large underground panel cave molybdenum mine located near Empire, Colorado. Diesel equipment is employed for all development work, as well as production ore handling. Due to fluctuating demand for molybdenum, production rates have varied from 16,000 to 32,000 metric tons per day (18,000 to 36,000 short tons per day) over the last four years. In order to obtain the maximum air flow for minimum power cost the Henderson mine has completed the following modifications to the ventilation system: removal of large intake fans, elimination of underground booster fans, shutdown of tunnel exhaust fans, completion of the number 5 exhaust ventilation shaft, and use of partially debladed main exhaust fans. These changes have reduced the annual cost of mine ventilation at the Henderson Mine by over 80 per cent, a very critical cost savings in today's competitive molybdenum marketplace.

Jan 1, 1989

By Alan A. Campoli, Michael D. Zuber, Frank E. McCall, Gerald L. Finfinger

Injecting water under pressure to wet the coalbed in advance of mining reduces mining-generated respirable dust. Owing to economic and geological barriers, water infusion for longwall dust control in the United States is currently limited to the Pocahontas No. 3 Coalbed in Virginia. Water is pumped into the coalbed through underground boreholes drilled horizontally from the headgate toward the tailgate side of retreat longwall panels. This paper theorizes that the barriers to widespread utilization of water infusion for longwall dust control could be overcome by long-duration, low-pressure water infusion through vertical gob gas boreholes. Currently, 43% of the 72 longwall mines in the United States employ vertical gob gas boreholes. Computer coalbed reservoir simulation suggests that one vertical surface borehole could infuse the same longwall panel area as four horizontal boreholes in the current water infusion system for longwall dust control in the Pocahontas No. 3 Coalbed.

Jan 1, 1995

By Sergio Godoy P.

The Los Bronces porphyry copper deposit is located in the high Andes of Central Chile. Ore is mined from several tourmaline breccias and from an earlier porphyry. After years of experience in the geostatistical estimation of reserves in different zones of the ore body, we believe that success lies in considering the evaluation as an integrated process beginning with the analyses of the drilling density and sampling methodology, ending with the critically important reconciliation between the estimated and the actually extracted ore, in general, when errors or differences occur, focus is centered in the calculation stages of geostatistics. However, this paper demonstrates that all the evaluation stages are equally important and require the direct and continuous geologic input to ensure the best possible estimate within the frame of the geologic constraints.

Jan 1, 1992

By Kenneth B. DeGraaf

The development of precious metal recovery processes using chloride systems has mostly evolved from the development of chloride based treatments for base metal concentrates or ores. The recovery of silver from chloride solutions within a process designed for the treatment of base metals usually is part of a solution purification stage. This paper discusses the development of the silver recovery stage used in the GCM HydroCopper process.

Jan 1, 1990

By Robert J. Storms, David J. Malone, Thomas E. Crandall

Corrosion and abrasion have been present in hydrometallurgical processes for many years. Ceramic lining materials have been used in several applications to protect process vessels from the corrosive and abrasive effects of a wide range of ore slurry processes. This paper reviews the history of ceramic lining systems utilized in hydrometallurgical vessels, the commercial benefits associated with their use, and additional areas of opportunity for the Mining Industry.

Jan 1, 1995

By George Wilson

As the economic and environmental attractiveness of conveying coal and ore slurries by pipeline increases, greater attention has been given to designing and selecting components for these pipeline systems. Pumps are one critical element in pipelining. Pumping slurries is a particularly arduous task, calling for special design and construction. The first article in this two-part series describes some factors to consider when selecting pumps to resist abrasive wear.

Jan 9, 1981

By Takeshi Shinohara

It is a great honor and pleasure for me as President of the Japanese Tunnel Association to send greetings to the 1974 Rapid Excavation and Tunneling Conference. Recently in Japan, the Japanese Tunnel Association was established as recommended by the OECD Advisory Conference on Tunneling. This is a central organization concerned with tunnel construction consisting of government authorities, universities' research institutes and construction firms as well as manufacturers of relevant materials and equipment. As I was chosen the first president of the newly-established Japanese Tunnel Association, I would like to avail myself of this opportunity to announce to you its establishment and its earnest wish to contribute to the development of tunneling technique not only in our country but also all over the world. At the same time, I cordially request your friendship and cooperation for the benefit of further development of tunneling techniques on both sides of the Pacific. At present, many tunnels are under construction in Japan. The total length of tunnels under construction for railways and highways is about 600km including the 54km Seikan Undersea Tunnel which connects the Main Island and Hokkaido. Naturally, for construction of such tunnels in Japan, we have introduced much equipment and technique from the United States and other foreign countries. Now with accumulated experience, we are confident to be able to furnish various useful information concerning tunnel construction.

Jan 1, 1974

By Maurice Deul

Certain health and safety hazards occur entirely unexpectedly in some subterranean excavations. Although ground support is not the subject of this paper, ground failure can result in large and often uncontrolled flow of fluids into an excavation. Even when there is no ground failure, the disturbance of nature's equilibrium between rock or unconsolidated alluvium or rubble and the contained fluids poses severe problems to a well planned operation. Optimum conditions for safe operation cannot be the sole criterion for site selection. Some mineral deposits form in zones of structural weakness, others form where hydrothermal alteration substantially weakens the enclosing rock, and tabular deposits such as coal and evaporites inevitably undermine large areas. Excavation to acquire mineral values cannot be relocated. The same is often true for tunnels driven to connect distant points by the most direct route. Rivers and mountains cannot he avoided, and the cost of lengthening a tunnel--by even a fraction of a percent--must be strongly justified. No responsible engineer will knowingly select a dangerous route for excavation, but to what extent do engineers attempt to assess the health and safety hazards that may be reasonably expected? How, specifically, can methane explosions, water and sand flooding, dangerous dusts, toxic gases, thermal shock and radar poisoning be eliminated or minimized through systematic advance planning?

Jan 1, 1974

By David J. Herzog

There are two steps in evaluating potential mine waste impacts on ground and surface waters. Characterize the mine waste (characterization methodologies) and assess potential impacts (assessment strategies). One or both may be required for mine permitting, operation and closure. The first step is to characterize the waste. Determine if it has the potential to release chemical constituents or acid rock drainage to the environment. If no potential exists for release to the environment, the evaluation process is complete. A monitoring plan is then established. If the potential exists for release of chemical constituents or acid rock drainage to the environment, a strategy to evaluate potential impacts must be implemented. Strategies discussed here to evaluate potential impacts were developed during investigations at precious metal and base metal mines in Nevada. Water resources in Nevada consist mostly of ground water. So the strategies discussed focus on potential impacts to ground water. However, several of these strategies also apply to assessing potential impacts to surface water. Implementing these strategies has helped determine the potential for impact and has been successful in permitting mine expansion as well as allowing continued operation and obtaining mine closure at several mine sites in Nevada. These strategies were carried out in accordance with Nevada Division of Environmental Protection (NDEP) regulations and through the National Environmental Policy Act (NEPA)

Jan 1, 1995

By J. M. Carter, Rodney H. Sergent, L. E. Kun, J. T. Pressly

Underground mine service water in South Africa is used for dust suppression and cooling the environment as well as the pneumatic rock drills. Although the chilled water is not intended for potable use, it is often used as drinking water by mining personnel. Furthermore, droplets sprayed are liable to be inhaled. The water is recirculated on a continuous basis and is a potential source of infection by intestinal microorganisms or water-borne diseases such as cholera or typhoid. In order to protect the health of the underground workforce it is customary to disinfect the chilled service water, The bacteriological quality of the water is monitored by enumerating total aerobic bacteria (TAB), total coliforms (C C) and Escherichia coli (E Coli). E coli is an indicator of human faeca_l __ - -- contamination, The bacteriological standard specified by the Anglo American Corporation for mine service water is less than 3000 TA B per 100ml, less than 2 CC per ml and the total absence of E Coli. There are several disinfecting agents available for use. Among these are UV irradiation, ozone, chlorine dioxide and compounds that produce hypobromous and hypochlorous acids. Historically, the methods of treatment have been chlorine based and include the use of gaseous chlorine (surface installations only), calcium hypochlorite granules or tablets, chlorinated cyanurate tablets, sodium hypochlorite solutions and hypochlorite produced by electrolysis.

Jan 1, 1991

By David Martin Menne

In a small tank, slurry is passed through the high shear impeller zone with small time intervals, and a large proportion is regularly exposed to air at the surface, and at relatively high shear rates. This accounts for significant differences in the performance of large and small tanks. It is preferable to derive data where possible directly from an operating plant rather than applying data generated in small tanks where allowances must be estimated for the above differences [and where slurry aging and often substantial cooling compared to hot freshly milled ore further distorts results]. Various measurements have shown that many gold slurries can suffer extreme variability, as streamers of bypassing material or boules of hold-up periodically condstitute the instantaneous discharge from a tank - the relatively high Yield stress of slurries [around 1 to 10 Pa] causes very incomplete homogenization of slurry in any tank, the worse the larger the tank and the more viscous the slurry. To provide a background for this subject, this monograph presents leach and adsorption models based on the fundamental physics and chemistry of these processes, and includes quantitative discussions of factors which can lead to deviations on scale-up. The Throughflow model which avoids the need for such alowances is then presented, as well as a Computer Programme applying this model, and which allows direct calculation of the effects of:

Jan 1, 1995

By J. F. T. Agapito

Significant economic benefits can result when rock mechanics is applied within a practical framework and integrated within the other engineering functions of the mine organization. Such application and integration requires management support and understanding of rock mechanics as a practical tool to help attain high standards of safety, productivity and resource recovery. For such an approach, a long-term geotechnical program is needed in most operations to build an adequate data base and to ensure that design and ground control issues are handled in a cost-effective manner. Best usage of rock mechanics in mining occurs when management recognizes the application as a long-term investment, where time is needed to realize good returns. The need for this approach is due to the difficulty in accurately predicting ground conditions ahead of mining. The practical application of rock mechanics must follow an iterative process of design and verification based on site-specific experience to account for geologic and mining impacts. Ground conditions experienced during mining must be used to check the initial mine design and, if necessary, to provide a basis for design modification. Such a practical rock mechanics program includes comparative experience, in situ instrumentation and numerical modeling. The program begins with the geologic site investigation and continues throughout the life of the mine. It is an integral part of mine planning and operation.

Jan 1, 1991

By Steven Johnson

The regulatory landscape has changed considerably since the first passage of Oklahoma's land-reclamation requirements in 1968 (Open Cut Reclamation Act of 1968). The Oklahoma Legislature revised the reclamation requirements in 1971 with passage of the Mining Lands Reclamation Act. With the passage of this Act, the Legislature empowered the Oklahoma Department of Mines with jurisdiction for permitting and regulatory authority over non-coal (industrial-minerals) mining operations. This act required all operators to file with the State, through the Department of Mines, a written application for a permit to engage in non-coal mining. Each application consisted of a mining plan, which included location maps of the proposed mining area along with a reclamation plan for the area to be covered. Additionally, a reclamation bond is required prior to issuance of a permit to ensure that the site would be reclaimed. Since 1971, the Act has been amended to include public notification and public participation in the review process of any application. Also, the operator can request that the Department review the mining plan based on the Life Expectancy of the mine, instead of the original one-year plan (HB 1409 in 1993). Even though the operator is granted a mining plan tied to the "Life Expectancy" of the site, the permit is reviewed annually for compliance as required by law.

Jan 1, 1999

By James L. Parks

This paper describes improvements in SAG and AG mill liner designs and their cumulative effect on wear life and mill availability. Routine procedures used by many SAG and AG mill operators to improve liner life are reviewed. Guidelines are provided for estimating the time required to replace worn liners along with practical methods to reduce downtime for liner replacement. Finally, the effects of mill operating conditions on liner wear life and breakage are considered.

Jan 1, 1998

By M. V. Chari

A prime objective of physical coal cleaning is the separation of raw coal into a clean coal product with the required low ash and pyritic sulfur content and a high ash refuse. The refuse should also contain a minimum amount of combustible matter. In order to be effective, cleaning processes require that the mineral matter in the feed, including pyrite, be largely discrete and free particles, liberated so that the particles are not attached or embedded in coal. Liberation of mineral matter from coal, particularly pyrite, was investigated by Bechtel as part of two fine coal cleaning research programs sponsored by the Department Of Energy (DOE), Pittsburgh Energy Technology Center (PETC). Two proof-of-concept (POC) plants, each with a capacity of 900 kg per hour, were installed and tested to evaluate production of ultra-clean coal using microbubble flotation and spherical agglomeration technologies. The plants were designed to produce clean coal with 2 percent ash and pyrite content lower than that achievable by conventional methods. Also, the quality targets were to be attained at energy recoveries above 80 percent. Bench-scale flotation and agglomeration tests indicated that it would be practical to grind the 6 mm top size feed coal to a mean particle size (050) of 10 micrometers in the POC test plant. In this part of the paper, the steps taken in the grinding circuit to maximize liberation of mineral matter are described.

Jan 1, 1991

By A. Pincomb

After determining minable acreage, tons are calculated by multiplying minable acreage by average thickness and by a volume-tonnage conversion factor. Converting from tons in the ground to tons sold across the scale takes fines and internally used and wasted stone into consideration, resulting in minimum losses of about 10% for limestone and 15% for sand and gravel. A high degree of certainty about thickness, lateral continuity and geologic character defines proven reserves. Assuming continuity of these characteristics defines probable reserves. By using tpa estimations and annual tonnage requirements, the life of a deposit can be quantified. The decision can then be made regarding the necessity of securing more acreage. Some landowners choose to multiply aggregate price, operating income, or a royalty rate by tons to arrive at a value for their reserves. In doing so they probably overstate the value of their land.

Jan 1, 2003

By G. Récoché

For the African continent promoting a sustainable utilization of its mineral resources could be considered as a key determinant to fight against poverty. Sustainable development performance indicators for measuring the economic, environmental and social impacts of mining activity are necessary for drawing up policies and sectoral actions, identifying and controlling risks, identifying and implementing sustainable development actions, negotiating between stake-holders, improving mine production, etc. To respond to this need, the SIGAfrique Network proposed to develop a joint decision support tool entitled the African Mining Observatory (AMO) and, to this end, develops a system of indicators to be integrated within the SIGAfrique database. The development of both the OMA and the indicators is based on a participatory method within the working groups, which comprise experts/participants from the 13 SIGAfrique partner and observer countries (Guinea, Burkina Faso, Mali, Tanzania, Niger, Mozambique, Kenya, Uganda, Senegal, Angola, Madagascar, Ethiopia, and Mauritania).

Jan 1, 2007

By Kenneth Maser, Douglas W. Ounanian, Joseph S. Boyce

Foster-Miller Associates, Inc. (FMA), under contract to the Department of Transportation (DOT) and the Urban Mass Transit Administration (UMTA), is currently developing an Extruded Tunnel Lining System (ETLS). The ETLS would reduce ground support costs in machine bored tunneling by eliminating the need for temporary support, and by slip-forming the final concrete lining directly behind the Tunnel Boring Machine (TBM). The system can advance at variable rates, from 0.6 to 3.7 m (2 to 12 ft) per hr, by combining three systems: a very high early strength concrete, continuously produced and delivered by a concrete process system; a slipform/bulkhead system for supporting the concrete prior to strength gain and exposure; and a control system for form/bulkhead alignment and concrete process control. Large-scale tests are planned to demonstrate the system in a 3 m (10-ft) diameter steel "tunnel".

Jan 1, 1981