Search Documents

By W. Ter-Minassian

Besides the question of the stability of the roof and walls, one of the main problems encountered with tunnelling and shaft-sinking through the soft ground of alluvial origin forming the sub-grade of most large towns is settlement. Public transport and road tunnels in town centres are particularly affected, as they cannot generally be designed at any great depth for several reasons, such as the fact that ventilation shafts and access to the surface by means of stairs, escalators, lifts, ramps and so on must be fitted into the limited space available and are therefore costly, and because of the difficulties of driving below the water table. It is for this reason, coupled with the need for wide radius curves, that tunnels now so often pass close under buildings and monuments which must not be exposed to any risk of damage from subsidence during excavation. Grouting is the usual method used for consolidating soils, improving their strength and making them less compressible, but it is itself liable to cause heaving and cracks in the buildings above and has many other attendant dangers, including continually revised estimates which are the reason for the often inordinately high costs met with in urban tunnelling to-day. The mechanics of the problem have been studied and it has been found that a fraction of the total settlement is

Jan 1, 1997

By Gary S. Brierley, Tracy J. Lyman

INTRODUCTION Geotechnical engineers play a major role in tunnel design primarily because tunnels are constructed entirely within the ground. In general, this role can be divided into two major tasks: subsurface investigations and project design. Under subsurface investigations, it is necessary for the geotechnical engineer to accurately describe the ground in which the project will be built. Under project design, it is necessary for the geotechnical engineer to work together with other members of the design team to make certain that the tunnel fulfills its intended purpose at least cost. Given in the paper are the authors' opinions about what constitutes an adequate scope of services for these two tasks on a tunneling project. SUBSURFACE INVESTIGATIONS o Background Study All subsurface exploration programs for tunnels begin with a thorough investigation of background information about the proposed site. Such background information includes geologic, reports topographic maps, aerial photography, and case history reports of other nearby tunnels. Once completed, it is necessary to study the background information so that the proper scope and magnitude of subsurface exploration work is performed in a manner that provides maximum input to a knowledge of those intact and rock mass properties that are important for an understanding of the entire ground mass. The blind application of field and laboratory techniques, no matter how sophisticated, is wasteful and potentially

Jan 1, 1989

By A. Cartwright, J. Cardwell

"Complex geology requires innovative approaches to confidently and appropriately model grade and geologic trends. Local Anisotropy Kriging (LAK), by Isaaks and Company, and MineSight® Dynamic Unfolding (MSDU) from Hexagon Mining are advanced interpolation methods designed to best estimate grade along deformed three-dimensional grade trends at sediment-hosted deposits. While LAK works in Euclidean space for the construction of variograms, kriging weight assignment, and non-linear local interpolation search ellipsoids, MSDU is far more dynamic and can utilize a modeled three-dimensional undulating surface representing a folded grade trend to construct the above mentioned. MSDU was implemented at the sediment-hosted, stratabound Tenke-Fungurume mining district and revealed major block-to-block differences in interpolated copper and cobalt grades compared to LAK. INTRODUCTION Grade estimation is the cornerstone of long-range mine planning. Pit designs, metal recovery, mining costs, reserves calculations and reporting are all dependent upon a reliable grade model. If the geology is poorly understood or the interpolation methods and parameters have been haphazardly constructed, then massive financial losses will be the inevitable outcome. Therefore, a properly trained geologist must use all of the appropriate tools available including deposit knowledge and advances in modeling technology to construct the most geostatistically and practically sound long-range block model. Certain deposits, such as the sediment-hosted deposits at Tenke-Fungurume, require an interpolation method that best suites the style of mineralization. In 2014, Hexagon Mining developed a tool in MineSight called dynamic unfolding (MSDU) that has the potential to improve upon previous Euclidean-based interpolation methods. MSDU utilizes the non-stationarity of a folded grade trend to more accurately construct variograms and improve interpolation results based upon a modeled three-dimensional surface. Geology Overview The sediment-hosted Tenke-Fungurume mining district is located in the southeastern part of the Democratic Republic of the Congo (Figure 1). The rocks within the district are primarily dolomites and shales from the lower half of the Roan Supergroup that were mineralized by ascending pregnant copper and cobalt rich brines within a massive sedimentary basin (Cailteux et al., 2005) (Figure 2). These oxidized brines likely found a fluid channel in the porous RSC unit. The surrounding rock units provided a redox boundary for copper and cobalt precipitation along organic rich beds, forming a massive stratabound deposit that was later broken up by several subsequent tectonic events (Dewaele et al., 2006). Layering and Block Orientations To capture the bedding-controlled nature of the Tenke-Fungurume copper and cobalt mineralization, each lithology type must be subdivided into individual layers with a uniform thickness (Figure 3). The thickness of each layer is determined by the user, but should equal the bench height to achieve maximum resolution within each lithology type. Composites are back coded from the model to achieve layer codes that match block locations."

Jan 1, 2016

By Rami Abousleiman, Gabriel Walton, Sankhaneel Sinha

"Although conventional coal mine designs are conservative regarding pillar strength, local failures such as roof-falls and pillar bursts still affect mine safety and operations. Previous studies have identified that discontinuous, layered roof materials have some self-supporting capacity. This research is a preliminary step towards understanding these mechanics in coal-measure rocks. Although others have considered broad conceptual models and simplified analogs for mine roof behavior, this study presents a unique numerical model that more completely represents in-situ roof conditions. The discrete element method (DEM) is utilized to conduct a parametric analysis considering a range of in-situ stress ratios, material properties, and joint networks to determine the parameters controlling the stability of single-entries modeled in two-dimensions. Model results are compared to empirical observations of roof-support effectiveness (ARBS) in the context of the coal mine roof rating (CMRR) system. Results such as immediate roof displacement, overall stability, and statistical relationships between model parameters and outcomes are presented herein. Potential practical applications of this line of research include: (1) roof-support optimization for a range of coal-measure rocks, (2) establishment of a relationship between roof stability and pillar stress, and (3) determination of which parameters are most critical to roof stability and therefore require concentrated evaluation.INTRODUCTIONRecent studies on pillar design have suggested that the assumptions utilized in traditional methods such as tributary area theory (TAT) (i.e. overburden has no self-supporting capacity, infinite pillar array, and CHILE material properties) are invalid in many geo-mining conditions (Esterhuizen, Mark, and Murphy, 2010; Frith and Reed, 2017). Although TAT is conservative with respect to pillar loading, and mine fatalities have steadily decreased since 1990, roof-falls and pillar bursts still occur and injure hundreds of miners per year (Mark, Pappas, and Barczak, 2011). Even though large-scale global mine failure has not occurred in a US coal mine since 2007, the mechanics of global and local stability as governed by the relationship between geologic parameters, mine geometry, and engineering design are still not well-constrained.Numerical methods are a highly effective tool that can be used to gain further insight into these relationships. When using such an approach, calibration to existing empirical relationships is imperative to ensure that numerical model results are realistic. In this study, we utilize the discrete element method (DEM) approach in Itasca’s Universal Distinct Element Code (UDEC v. 6.0) (Itasca, 2010).DEM accounts for explicit separation and contact of individual deformable blocks (Jing, 2003) and captures how discontinuities can affect system behavior. Discontinuous and anisotropic rockmass properties are typical features in coal-measure rock which contain various horizontal (bedding) and sub-vertical (joints) fractures depending on their depositional environment, diagenesis, and historic and current stress states."

Jan 1, 2019

By K. Perry, R. Eades

"Highwall miners continue to be implemented by operations to increase recovery, improve margins, and justify higher stripping ratios as high quality surface reserves become increasingly rare. Many times, operations facilitate projected underground operations by leaving an intact highwall for development purposes. These facts result in larger highwalls that are left standing for increased periods of time prior to reclamation. As a consequence, worker exposure and risk is also elevated, resulting in higher potential for accidents or fatalities relating to surface highwalls. Highwall stability is a complex issue, dependent on both geologic and mining factors. Dynamic numerical modeling offers the capability to assess possible stability issues related to blasting-induced ground vibrations. Research has been conducted to evaluate the effect of highwall stability due to ground vibrations from blasting events. Additionally, the relationship of amplitude and frequency, and their impact on highwall stability is investigated. The results of this modeling indicate that amplitude has little impact on stability. However, frequency has a significant impact on highwall stability. INTRODUCTION The number of mining fatalities has declined since 2010, and 2016 is currently on pace to continue this trend (MSHA 2016). This decline can be directly correlated to the decline in surface mining activity and the overall decline of the coal industry. However, since 2002 the percentage of surface coal mine fatalities associated with highwall activities remains relatively high, constituting approximately 15% of all surface mine fatalities. 2014 was the first year with a highwall failure fatality since 2011. Most recent surface coal mining fatalities are associated with machinery and haulage. Table 1 provides a summary of the total surface coal mining fatalities, and the number of highwall failure fatalities dating back to 2010.Highwall stability is a complex issue, dependent upon geology and geologic discontinuities within the rock mass, along with highwall geometry, standing time, and applied stresses. Another possible concern that has not been previously investigated is the effect of blasting-induced stresses on highwall stability and the stability of web/barrier pillar systems as a result of ground vibrations from blasting events. Many modern surface coal mines employ numerous extraction fronts that rely on blasting for primary rock breakage. This results in highwall and highwall pillar systems experiencing blasting-induced stresses of many different types and magnitudes."

Jan 1, 2017

By Martín A. Encinas-Romero, GUILLERMO TIBURCIO-MUNIVE, María M. Salazar-Campoy, Patricia Guerrero-Germán, José R. Parga-Torres, Luis S. Quiróz-Castillo, JESÚS L. VALENZUELA-GARCÍA

Pressure oxidation is a hydrometallurgical oxidative pretreatment for refractory ores, such as sulfide ores. Here, simultaneous alkaline pressure oxidation and sodium cyanide leaching treatments were carried out on a pyritic ore from the Mulatos Mine located in Sahuaripa, Sonora, Mexico. Mineral characterization, agitation leaching, hot cyanidation under atmospheric pressure conditions, simultaneous moderated pressure oxidation and leaching, and kinetic testing results are shown. The modified variables were temperature, pressure, and cyanide concentration. Characterization indicated that pyrite was the main mineral. Simultaneous pressure oxidation and leaching experiments were conducted at a temperature range of 40–80 °C, oxygen pressure of 87.5–200 psi, and cyanide concentration of 0.8–1.2 wt% in a 2-L Parr pressure reactor. A dissolution rate of 81–86% was achieved under the following conditions: 87.5 psi, 80 °C, 0.8 wt% NaCN, for 1 h.

May 7, 2020

By L. Berwick, A. Karunanayake, D. Skutt, H. Heath, J. Wang

Thallium (Tl) is a highly toxic heavy metal, soluble over a wide pH range. Tl levels may exceed discharge limits in mining-influenced water associated with processing gold, lead, cadmium, zinc, and copper ores. In this work, the effect of sodium permanganate (CARUSOL® C liquid permanganate) on Tl removal from mining wastewater was studied. Factors influencing Tl removal, namely permanganate dosage/demand, coagulant and flocculant use, order of chemical addition, and co-existing metal ions were examined. The results show that permanganate addition is very effective at removing Tl to below target limits and can provide a unique solution for improving wastewater quality and optimizing overall treatment costs. In addition, several on-line monitoring techniques were evaluated for process optimization. The Hach DPD Free Chlorine method was optimal, allowing plant operators to rapidly and easily spot check effluent samples for excess permanganate dose.

Mar 2, 2022

By F. Schreiter

"One method to increase the exploitation rate of a mine is the use of backfill with residual materials in exploited areas. The backfilled material is meant to support both, the walls of galleries and pillars as well as the roof of mining openings. With increasing depth, the exploitation rate diminishes fast, thus the application of backfill in order to change the layout of the mine is crucial for economic success. In result of using backfill, it is possible to change the layout of the working area with a higher ratio to excavated areas and less area occupied by pillars. Thus it is possible to boost the output of a mine by using backfill. Setting the criteria for the selection of the best possible materials and whose improvement, it is useful to know about their qualities and handicaps. The Mining Department at TU Bergakademie Freiberg is analyzing the parameters of residues from different processing methods, accrued in plants of different potash mines and blending different residues for optimization of material attributes. These were significantly characterized by basically parameters like the size and the distribution of different diameters of the grain material. INTRODUCTION The chair for underground mining methods at TU Bergakademie Freiberg is tasked with the sufficient and sustainable supply of economics with raw materials. The steady high demand, the rising prices and the finiteness of the deposits are reasons for the need of an optimized economic utilization of natural deposits, a continuous improvement of mining technics and technology. From an ecological and economical position the best possible utilization of the resources has to be achieved. Many mining operations are by reasons of the deposit not able to haul valuable minerals only, they have to haul a mixture of valuable minerals and waste rock. This hauled combination is given into the processing plant for separation and enrichment of the valuable mineral. The residuals of the processing are commonly dumped to a waste rock pile. For minimizing the size of such a waste rock pile and also minimizing the ecological footprint of a mining operation the only way is minimizing the quantity of accruing waste rock material. Both, optimization of economic utilization and also minimization of waste rock dumps can be realized in one by backfill with processing waste rock material in mined out areas. Especially in mines, mined by room and pillar method, smaller dimension of the pillars are sufficient for safety and stability. By the way less valuable minerals have to be leaved back in the mine and the mine outcome is increasing."

Jan 1, 2015

By R. Asamoah, K. B. Owusu, G. Abaka-Wood, W. Skinner

The hostile nature of industrial autogenous (AG)/semi-autogenous (SAG) mill operation necessitates the need for robust and reliable online measurements. Mill slurry density is regarded as a critical variable and requires a suitable range for grinding efficiency. In this work, mill acoustic sensing of five different slurry densities (50, 60, 70, 80 and 90 wt.% solids) was investigated using a laboratory-based AG/SAG mill. The results showed that slurry density of 70-80 wt.% solids gave the highest mass of -75μm particles and similar acoustic intensity. The mill acoustical level increased continuously coupled with energy reduction as a function of increasing slurry density, an indication of potential realtime measurement.

Mar 2, 2022

By Trent A. Tempel

In 1989 Newmont Gold company initiated a project to develop a treatment process for higher grade refractory gold ores to be mined from deposits along the Carlin Trend in Nevada. Extensive laboratory and pilot testing have identified a unique whole ore roasting process for oxidizing these ores prior to gold recovery by conventional cyanidation techniques. Subsequent detailed engineering studies by Fluor Daniel evaluated three different dry grinding flowsheets for feed preparation to this roasting circuit. The selected flowsheet will incorporate a two compartment ball mill with an attached drying chamber that is driven by a 11.2 MW (15,000 hp) wrap-around motor.

Jan 1, 1993

By J. C. Ransdell

A conventional paddle-type mixer and a gravity-flow mixing device were evaluated for conditioning of fine phosphate feed (- 35 + 150 mesh) with fatty acid and fuel oil, and for acid scrubbing prior to cationic flotation. Gravity-flow mixing re- quired less residence time but slightly higher reagent concentrations to achieve recovery levels similar to conventional conditioning. Grade was less sensitive to reagent concentration using the gravity-flow mixer. For acid scrubbing, the gravity-flow mixer proved equally effective. In this paper, the effect of time, pulp density, reagent concentration, and emulsification on conditioning and acid scrubbing efficiency of the two devices is discussed.

Jan 1, 1987

By Erik S. Bernard

"INTRODUCTION Conventional steel bar reinforcement is used in many tunnel linings to provide high flexural and tensile load resistance. These Reinforced Concrete (RC) tunnel linings may suffer flexural cracking during service or, in the case of precast concrete segments, during production, handling, or installation. Cracks can lead to corrosion of steel reinforcement, so limits are placed on maximum acceptable crack widths to reduce the likelihood of corrosion during the intended design life (AFTES, 2013; MC2010, 2012). However, the relatively light level of reinforcement used in many applications can result in quite wide in-service crack widths, so either additional steel bar reinforcement is required to limit maximum crack widths, or fibers can be included to control crack widths. Numerous investigations have been undertaken into the efficacy of including steel fibers to reduce crack widths in conventionally reinforced members (Stang and Aarre, 1992; Abrishami and Mitchell, 1997; Bischoff, 2003; Dupont and Vandevalle, 2003; and Jansson et al, 2010), but steel fibers suffer the problem that they are at least as sensitive to corrosion at cracks as steel bars and therefore have similarly tight limits placed on acceptable crack widths (AFTES, 2013). An alternative means of maintaining narrow crack limits in RC members has therefore been sought. The current investigation was instigated following an observation that theories promoted as an explanation for the ability of steel fibers to reduce crack widths in reinforced concrete flexural members (Deluce et al, 2014) do not depend on the material composition of the fibers used but instead depend primarily on the tensile stress generated by the fibers across cracks. Since it is known that macro-synthetic fibers are capable of equaling the post-crack tensile capacity of steel fibers, it has been hypothesized that macro-synthetic fibers are also capable of reducing crack widths in reinforced concrete flexural members but with the added advantage that macro-synthetic fibers are completely immune to the effects of corrosion. Use of macro-synthetic fibers to reduce maximum crack widths in reinforced concrete flexural members subject to aggressive environmental exposure is more rational than use of steel fibers because steel fibers are very sensitive to the corrosive effects of environmental exposure at cracks. The current investigation was therefore undertaken to explore the potential use of macro-synthetic fibers to reduce maximum crack widths in reinforced concrete members subject to flexure. Barchip BC54 fibers were selected as they are one of the most widely used and competitive high performance macro-synthetic fibers currently available."

Jan 1, 2016

By Barry R. Doyle, James P. Rose, Marius P. Gronbeck

This paper presents a strategy for addressing the hazards of construction of tunnels in ground containing methane. A discussion of the nature of methane includes occurrence underground, and manner of entry into excavations. Means of methane control for underground operations are discussed, including ventilation, monitoring, equipment selection, and personnel training. Principles of ventilation for gas dispersion and removal are addressed. The use of continuous gas monitors, automatic power shutdown systems, and hand-held detectors is discussed. The paper addresses integration of permissible equipment to provide a safe system. Aspects of personnel training are discussed, including maintaining hazard awareness, and evacuation and re-entry procedures.

Jan 1, 1991

By T. D. Murphy

In the fall of 1988 it became evident that the accuracy of sulfur forecasts for Monterey Coal's No.1 Mine needed to be improved. In addition, it became necessary to predict if any individual train shipments during a month would exceed a contract sulfur limit. The challenge was to develop a forecasting process that would take into account the variability of the coal in the ground as well as the difference between laboratory and preparation plant sulfur reduction efficiency, and the effects of mining coal with multiple units. This paper describes how geostatistics and simulation techniques were used to meet this challenge.

Jan 1, 1992

By J. Patrick Glynn

The paper compares the METSIM model simulation and the actual operating data at Sleeper Gold Mine in Nevada. The simulation utilized by the model is a combination of Bond's models, models for breakage and selection functions and the Krebs model for cyclones.

Jan 1, 1992

By Dale R. Ralston, Roy E. Williams, Gerry V. Winter, George L. Bloomsburg

Ground water inflow into a mine and the re¬sultant impact on district hydrology can be pre¬dicted on a site specific basis once the ground water flow systems at the site are sufficiently well under¬stood so that a valid conceptual model can be de¬veloped. Ground water flow systems are controlled by the hydrogeologic properties of the materials at the, site, including hydraulic continuity along flow paths, and boundary conditions. Preliminary delin¬eation of hydrostratigraphic units for conceptual models frequently can be based on surface water data; specifically, spring locations and the gain-loss reaches of streams. Quantitative predictions of mine water inflow and its impact on regional hydrology require col¬lection and analysis of numerous types of data. Hydraulic conductivity must be defined quantita¬tively both parallel and perpendicular to bedding as well as areally for each hydrostratigraphic unit. The characteristics of the Davis shale in case his¬tory number 2 illustrate this concept very well. The storage characteristics also must be determined for each hydrostratigraphic unit and the potential or hydrostatic head should be quantified vertically and areally for each unit. The potentiometric measure¬ments in the Bonneterre Formation as discussed in case history number 2 illustrate this point. The data collection and data analysis techniques constitute the weak link in the analysis of mine inflow and district impact. The technology for char¬acterizing a mine site in the field has lagged behind the technology for mathematical simulation; we at¬tribute this development to the fact that computer modeling is relatively inexpensive compared to field data collection and analysis. On-site tests provide the best means of quan¬tifying hydraulic conductivity parallel to bedding and the storage characteristics of the unit. Pump tests with multiple observation wells provide the best information from on site tests. Hydrogeologie boundaries can be located from such multiple well tests. Multiport piezometers provide a means for determining the vertical potential in a single borehole. Borehole geophysics can facilitate the def¬inition of hydrostratigraphic units. Vertical hy¬draulic conductivity is difficult but not impossible to quantify with existing field test methods; labo¬ratory tests of cores fail to give a value represent¬ative of the field situation. The storage characteristics of a confined (artesian) hydro¬stratigraphic unit can be difficult to quantify when pumping changes the confined unit to an uncon¬fined (water table) case after depressurization and dewatering. Transmissivity and storage coefficient can be approximated to some extent for given field con¬ditions by computer modeling if enough is known about hydrogeologic boundaries. Modeling can be used in a trial-and-error approach to match transmissivity and storage coefficients to existing water level data corresponding to estimated discharge rates. A solution can also be obtained using a tech¬nique referred to as the inverse method. Unfortu¬nately, such a solution is seldom unique. Fracture flow models exist but practicality usu¬ally necessitates reversion to a basic Darcy flow model. Data requirements for fracture flow models could be difficult to fulfill where fracture aperture, spacing, orientation, and length are required. Ob¬taining such data at depth prior to mining would be impossible for any mine simulation in fractured media. We are of the opinion that most fractured media simulations can be accomplished using con¬ventional Darcy flow models by viewing the field problem on a macroscopic scale. The real challenge is to delineate hydrostratigraphic units properly in the field. The question of whether a broken-up fault zone is an aquifer or a barrier boundary is seldom simple. The fractures usually can be treated as an equivalent porous medium in either case. Only a few techniques exist for predicting un¬derground mine water inflow. These techniques fre¬quently are designed to evaluate shaft or tunnel inflow under steady-state head conditions in a sin¬gle layer rather than in multiple hydrostratigraphic units. Few computer programs exist that have the

Jan 1, 1986

By A. G. Belova

Conversion of coal into high-value gases via gasification offers significant pollution reduction and efficiency improvement benefits associated with controlled combustion of clean gases for power generation. However, current gasification-based electricity production technologies, such as IGCC do not address carbon dioxide emissions. The focus of the study is CO2 capture on CaO prior to combustion of coal-derived gases. To overcome kinetic and stability limitations associated with its utilization, CaO is distributed on high-surface area -Al2O3 and supported on a ceramic honey-comb monolith. The proposed method allows for efficient capture of CO2 from a gas mixture, as studied in a flow-through reactor system. This novel method of CO2 capture is used here to argue for pre-combustion capture of CO2 in coal gasification-based power plants. When CaO is present during the steam reforming of coal gasification gases, continuous withdrawal of CO2 from the system provides for higher yields of reforming products (hydrogen gas) by influencing the thermodynamic equilibrium of the entire system.

Jan 1, 2009

By Fulian He, Jianhang Chen, Shoubao Zhang

"Fully grouted rock bolts have been used in mining industry for many years. Significant research has been conducted to evaluate the load transfer behavior of fully grouted rock bolts with experimental programs. However, compared with that, less work has been conducted with analytical modelling. Therefore, in this paper, the authors used an analytical model to study the load transfer behavior of fully grouted rock bolts. To confirm the credibility of this analytical model, an in-situ pull-out test was used to validate this model. There was a close match between the experimental result and the analytical result. Following this, a parametric study was conducted with this analytical model. The influence of coefficients, Young’s modulus of the rock bolt and the diameter of the rock bolt on the load transfer performance of rock bolts were studied. Furthermore, the load distribution along the fully grouted rock bolt was analytically studied. The results show that the axial load in the rock bolt decayed from the loaded end to the free end independent of the pull-out load. However, the trend of the load distribution curve was influenced by the pull-out load. This paper was beneficial to better understand the load transfer mechanism of fully grouted rock bolts.INTRODUCTIONRock bolts have been used in the mining industry for a long time. They are used as the reinforcement tendons to keep the stability of openings in underground mining and the slope in open-pit mining. Furthermore, rock bolts are commonly used not only in the mining engineering, but also in civil engineering (Thompson, Villaescusa, and Windsor, 2012).The rock bolt is a tendon which can be a rod or a cable inserted into a borehole drilled in rock masses or soils. Traditionally, the material of rock bolts was steel. However, engineering practices showed that the steel rock bolts can be easily corroded by the moist environment in underground mines. Next, Fiber Reinforced Polymer (FRP) was used to manufacture rock bolts, which are termed as FRP rock bolts. Experimental results proved that the FRP rock bolts can effectively reinforce the surrounding rock masses without being corroded (Wang et al., 2018)."

Jan 1, 2019

By J. P. Wilson

The Tessenderlo-Kerley Leach process has been shown to be effective in the removal of residual copper from molybdenite concentrates. Concentrates of varying mineralogy, including those containing relatively large amounts of chalcopyrite, have been successfully leached on laboratory and pilot plant scales. The lixiviant system is ammonia and ammonium bisulfite with air / oxygen addition. An abrasive is added which greatly enhances the kinetics, and it is subsequently screened out and reused. The dissolved copper is easily recovered using existing technology. Extraction profiles, reagent consumptions, and mineralogical data are presented.

Jan 1, 1999

By G. Piegols, J. A. Lombardi

Substantial volumes of cyanide are consumed in precious metals mining due to the purposeful destruction of base metal cyanide complexes and free cyanide to meet surface discharge regulations. This destruction of cyanide resource runs counter to the prevailing social ethic of resource conservation wherein cyanide recovery-and-reuse is considered a more socially responsible cyanide use pattern than systematic cyanide destruction. HW Process Technologies, Inc. (HWPT) has developed membrane based methods for the recovery of cyanide from barren solution as a means to reduce cyanide waste. The HWPT Engineered Membrane Separation (EMS™) system uses state-of-the-art spiral wound membrane elements that are engineered specifically for the treatment of high pH cyanide process solutions. The membranes fully reject WAD CN, SAD CN and most minor metals, and partially reject SCN, Free CN and precious metal cyanide from a high clarity barren solution feed to a small volume EMS™ “concentrate” stream. The EMS™ “concentrate” stream is returned to the process. The large percentage of the EMS™ process feed exits the system as cyanide lean EMS™ “permeate.” The EMS™ permeate, after residual cyanide destruction, polishing, and pH adjustment, is, thereafter, typically suitable for discharge. Separately, the HWPT EMS™-PLS method of cyanide recycling is an internal plant cyanide recovery step that removes base metal cyanides from a pregnant leach solution to a small volume EMSTM concentrate stream. The concentrate stream is then typically processed further for the recovery of metals and recovery-recycling of cyanide. The method makes it economically practical to recover gold from Merrill-Crowe or car-bon plant “fouling” solutions, e.g., those with greater than 400 ppm Cu, as might result from the use of the EMS™ method wherein EMS™ concentrate is constantly thrown back into the mine leach solution pool as part of the free cyanide recycle process, or as might result from the single-pass leach treatment of high copper content ores or concentrates. The EMS™ cyanide recovery method for barren solution treatment is shown to be “economic” for the treatment of clear solutions at the approximately 200 ppm total cyanide level (CNT), and for slurries at the approximately 400 ppm total cyanide level, where economic is defined as a 2 year EMS™ plant payback. The EMS™ plant payback calculation includes the beneficial monetary impacts of gold and free cyanide recycling and the avoided operating cost of cyanide destruction.• The cyanide recovery plant payback period is reduced further when the avoided capital costs for cyanide destruction (EMS™ permeate “clear solution CN destruction polish” only required) and/or metals precipitation are considered.

Jan 1, 2004