Search Documents

By R. Hogg, M. Polat, S. Chander

A fresh dust generator was designed and built in order to study the agglomeration behavior and other characteristics of freshly generated airborne dust. The size distribution of the freshly generated quartz airborne dust produced by the generator was measured both directly in air and after dispersion in water. It was observed that same dust particles had an apparently coarser size distribution in air than in water, suggesting possible agglomeration of the dust particles. It was also observed that the size distribution obtained by a cascade impactor was very similar to the liquid dispersed size distribution, implying deagglomeration by the impactor. The agglomeration was confirmed by microscopic observations of particles in air and those collected on a microscope slide. The extent of agglomeration played a decisive role on the fraction of the dust actually becoming airborne. It was also found that contamination of the airborne dust by the rolls of the crusher was almost twice as much as that of the product.

Jan 1, 1991

By John Matthews

During 1982 and 1983, it became increasingly clear that North River No. 1 Mine would have to buy a set of replacement longwall shields. Despite extensive efforts to make improvements, the shields that were in place at that time were incapable of holding the roof. North River Energy had limited experience in specifying and acquiring longwall roof supports, but a great deal of experience with our conditions and needs. We there- fore compiled a shield evaluation method that uniquely responded to our situation. The resulting system emphasized teamwork among operating, maintenance and engineering personnel. The charge from management was threefold: select shields to support maximum expected loads, optimize face operations, and pay attention to detail. Final selection was made objectively, based on all available information. We chose a 5516 KN (620 tons) support with a minimum yield load density of 760 KN/m2 (7.9 tons/ft2). This paper reviews our process of specification, design, prototype testing, and fabrication, and offers some relevant suggestions.

Jan 1, 1986

By J. B. Hiskey, S. Chander, B. J. Scheiner

The use of selected iron complexing agents in preventing or ameliorating acid mine drainage was investigated. The experiments were conducted in weathering columns using refuse samples from a coal cleaning plant. It was observed that the treatment with iron complexing agents significantly altered the rate of oxidation. Some of the reagents tested reduced the rate of oxidation whereas the others even enhanced it. The results showed that a commercial reagent containing oleyl imidazoline was most effective in retarding the oxidation rate. In addition, a simple treatment with this reagent substantially decreased the rate of oxidation of pyrite in a column that was generating acid at a high rate. The effect of this reagent on the surface properties of pyrite was studied by cyclic voltammetry and zeta potential measurements. The decrease in the rate of oxidation resulted from suppression of both anodic and cathodic reactions at the surface of pyrite.

Jan 1, 1993

By H. S. Kibler, A. E. J. Gallagher, J. J. Sebesta

A review will be made of the nature, value, costs, and factors associated with industrial minerals production in general. Comparisons will also be made between some of these data and similar criteria for metallic mineral production.

Jan 1, 1987

By Robert Martinez

A proven high grade reserve of gold mineralization located in Mexico is evaluated to determine which gold recovery process is best suited for this deposit. The processes evaluated are; Heap leaching, Vat leaching and a CIP circuit. All qualify as viable options, however each one presents a different economic picture which is impacted substantially by the financial constraints of the project. Taking this into consideration the most economic process was selected.

Jan 1, 1987

By Bob Newbery, Kenneth W. P. Eng. Kolthammer

SUMMARY Reference is made to the reasons for drying and the equipment is described that is available from which the engineer can make a selection. The factors affecting this decision are described. In the case of drying, design and sizing are ultimately developed empirically and no theoretical approach has been advanced.

Jan 1, 1986

By John A. L. Campbell

Are safety concerns justified regarding the potential for a gas explosion due to recirculation when a scrubber is used on a continuous miner? The role of a respirable dust scrubber on a continuous miner section using blowing face ventilation is examined in this paper and the above question answered. Methane control using high efficiency scrubbers coupled with blowing face ventilation is promoted.

Jan 1, 1987

By Vanessa M. Torres, Renato S. Costa

This work presents the experience of Cia. Vale do Rio Doce in using Diagnostic Leaching tests to characterize refractory ores and CIP tailings. With the diagnostic leaching results of the highly refractory gold ore from Maria Preta Mine (Brazil), a process flowsheet was defined for a feasibility study of possible process modification on the existing plant. With CIP tailings from its Fazenda Brasileiro and Caué operations the amount of cyanidable gold was determined to aid plant optimization.

Jan 1, 1995

By Richard J. Frechette

Final reclamation of mine tailings impoundments typically involves addressing the broad issues of surface stabilization and water management. Surface stabilization includes immobilizing the tailings particles and providing long-term protection of the containment facility. Water management typically includes provisions for handling both the external water (rainfall and runoff) and the internal water (pore fluids). Wet tailings disposal facilities, and sites with limited access and steep topography, present challenges to implementing effective surface stabilization and water management plans. This paper presents a generalized discussion of the approach to tailings impoundment reclamation based on project experience.

Jan 1, 1995

By R. D. Hamilton, W. J. Miles

In 1987, the International Agency for Research on Cancer designated crystalline silica as a 2A probable carcinogen. As a result, crystalline silica is regulated under the Hazard Communication Standard as a probable carcinogen at a concentration of 0.1% or greater in the workplace. Crystalline silica will be listed as "reasonably anticipated to be a carcinogen" by the National Toxicological Program. This designation of crystalline silica as a probable carcinogen has created major issues for the mineral and chemical producer, including labeling, hazard communications, marketing a material with potential hazard exposure, and potential liability. The State of California also regulates crystalline silica under Proposition 65 in products as a carcinogen, based upon the IARC determination that it is a probable carcinogen. More federal and state regulations are anticipated as a result of the IARC classification of crystalline silica and its subsequent federal regulation. Respirable crystalline silica has been regulated as a hazardous dust for many years by OSHA. This regulation was initiated to prevent silicosis, another occupational disease. OSHA has established monitoring devices for determining the concentration of airborne respirable silica in order to measure exposure to this substance. The accurate determination of the crystalline silica content is critical to dealing with these health risks and regulations. In the past, crystalline silica was considered to be safe and, because of its ubiquitous nature, little effort was made to determine or quantify its presence in most materials. The Hazard Communication Standard requires that a1l products containing 0.1% or greater crystalline silica must be properly labeled for this material and its hazard. Unfortunately, the 0.1% threshold was not chosen on the basis of established analytical capabilities for crystalline silica, but results from general limits for potentially carcinogenic chemicals and substances. Numerous methods have been developed for the determination of crystalline silica in a variety of products. However, these methods are not generally applicable since they must be specific for silica in any of its crystalline states and not just for total silica content. Chemical tests for silica are not difficult and quite accurate at the 0.1% level; however, in addition to its crystalline phases, it occurs in amorphous phases and in a wide variety of crystalline and amorphous silicates. In general, there is little correlation between total silica content and crystalline silica.

Jan 1, 1991

By G. Chi, M. C. Fuerstenau, R. C. Bradt, A. Ghosh

With increased emphasis on controlled blasting, which is the first and least-costly stage of comminution, ore grindability and plant throughput can be increased by 5% to 10%, and energy savings of up to 10% appear possible. Crushing and grinding efficiencies are presented for ore blasted under regular and adjusted field conditions. An economic analysis of drilling and blasting through crushing and grinding is presented, suggesting that cost savings approaching 10% may be achieved.

Jan 1, 1998

By Q. Xu, P. Somasundaran

Adsorption of nonionic/anionic surfactant mixtures on kaolinite has been studied, with •Sodium dodecylsulfate as the anionic surfactant, and •Octaethyleneglycol mono-n-dodecylether as the nonionic surfactant. Synergistic interaction between these surfactants was found to cause adsorption of the nonionic surfactant with its hydrophilic chains protruding into the bulk, leading to substantial changes in wettability and dispersion characteristics of kaolinite. Similarly, hydrophobicity changes are observed also for silica particles upon adsorption of nonionic ethoxylated alcohols owing to possible changes in the orientation of the adsorbed surfactant molecules at the interface.

Jan 1, 1993

By Andy J. Robinson, Mark D. Claassen

Railroad companies and transit authorities have been slow to acknowledge that for many—utility crossings, a direct pipe installation below live rail can be just as effective as a more intrusive traditional cased crossing. Properly designed and specified pipe jacking work, and specifically pressure-balanced microtunneling, coupled with careful specification and analysis of geotechnical monitoring and, where necessary, ground improvement measures, can produce a low-risk, low ground movement solution to the needs of utility companies and municipalities whose services need to pass below urban and rural rail corridors. This paper discusses the design, geotechnical and ground improvement aspects of microtunnel crossings below active heavy and light rail lines and crossings beneath active subway tunnels.

Jan 1, 2003

By Li Honggui, Liu Maosheng, Zhao Zhongwei, Sun Peimci, Li Yunjiao

Leaching of Shizhuyuan low-grade refractory tungsten ore was carried out in a mechanically activating reactor. The effect of experimental parameters-temperature, amount of Na2C03, addition of NaOH, ratio of liquid to solid and leaching time - on the recovery of WO3 was studied. The WO3 recovery up to 96.99% have been achieved when the tungsten ore was digested by soda not more than three times the stoichiometric amount at 185-195°C for 1 .O-2.0 hours. Iso-extraction countour diagrams were drawn to illustrate the effect of various parameters on leaching. The WO3 recovery could be expected to increase 10-15% compared to that of conventional soda autoclave process.

Jan 1, 1995

By S. H. Advani, J. K. Lee, K. S. Chan, J. M. Avasthi

A summary of field equations governing the hygro-thermo-mechanical (coupled temperature, moisture, and stress) response of geological media is presented. The applicability of these equations, with appropriate boundary conditions, to the study of basic mechanisms associated with underground coal gasification (UCG) process is discussed. In particular, the phenomenon of stress-induced spalling resulting from intense drying near the gasified cavity and in situ effects is investigated by means of the finite element method. Some typical results from sample finite element model representations are presented for the evaluation of field experiments.

Jan 1, 1986

By Mayank Srivastava, Satya Harpalani

Production of methane is an inevitable consequence of mining coal. Although the number of mines practicing recovery of methane prior to, or during, coal mining is increasing, ventilation air methane (VAM) is still a significant source of methane addition in to atmosphere. Recent studies have shown that there are ways to recover the VAM energy, while simultaneously reducing the methane emission in to atmosphere. This paper discusses a case study, currently underway, to develop a technique to quantify the VAM emission from a mine. It also presents the different VAM utilization techniques and the suitability of one for the mine being studied. Finally, the paper summarizes the research issues that require further investigation.

Jan 1, 2005

By Prisbrey K., N. Choi, A. Burbank

Large tonnages of low grade refractory gold ores are not presently being treated because they resist direct cyanide heap leaching and because they are too low in grade for more expensive oxidizing pre-treatments. If they could be oxidized while remaining in heaps, they could be economically leached with cyanide. The solution is to use bacteria to partially oxidize the encapsulating pyrite mineral which allows cyanide dissolution of the gold in a separate treatment. A variety of refractory ores from different locations was crushed to minus three quarters inch, loaded into columns, and inoculated with T. ferrooxidans. The bacteria attacked the pyrite causing biooxidation, and gold recovery increased 30 to 120 percent after three months curing.

Jan 1, 1990

By Jorgen Elbrond

The economic environment of mining is particular and requires special methods for seeking the economic optimization of mining and guiding the construction of logical production planning systems. An interactive program system which generates sequences of mining rates and cutoff grades, using as it's core an open-ended dynamic programming algorithm, is described. The program system is built not with the aim of obtaining a single mathematical optimum, but on the concept of satisfying the mine planner by producing several alternative mine plans and testing various schedules under conditions of uncertainty.

Jan 1, 1982

By John T. Crawford

Various open pit limit-analysis techniques have been utilized for many years to design pit limit surfaces. In the last 15 years there have been many advances in developing sophisticated computer methods to aid this process. The extensive capability of the digital computer has led to effective utilization of multiple alternative approaches to problem solving. Computerized open pit limit analysis methods can be applied to a broad scope of long range and intermediate range mine planning and design needs. This paper provides an overview of some of the more important of these applications. While not covered in detail, they are meant to indicate the flexibility and adaptability of open pit limit analysis methods and to stimulate thought.

Jan 1, 1979

By Daniel L. Hanson

This paper presents case histories of the construction of four large diameter circular shafts using reinforced concrete ring beams as the primary internal support system. The case histories pertain to concrete ring beam systems which have been successfully used in shafts up to 130 feet in diameter and 75 feet deep. Soldier pile and lagging, and driven steel piling earth retaining systems using ring beams, are discussed together with the cost savings associated with using concrete ring beams. Soil conditions encountered at the case history sites are discussed together with the development of design criteria for each shaft. Instrumentation data obtained at one site are also presented.

Jan 1, 1987