Search Documents

By Rudrajit Mitra, Wesley B. Johnson, Erik C. Westman

The ability to understand stress redistribution within a mine allows greater extraction efficiency with reduced safety concerns. Stress redistribution has been examined at the laboratory scale using ultrasonic tomography and numerical modeling using PFC3D. A data acquisition system was built to obtain tomograms as samples are loaded in uniaxial compression. Limestone samples were loaded to failure. Three-dimensional tomograms of the samples correlate to various stress distributions. The tomograms are compared to analytical and PFC3D results.

Jan 1, 2005

By Zsolt Csillag, Dragorad Ivankovic, Miomir Ceh, Anna Csordás-Tóth

Results of the common research work of ALUTERV-FKI and RI in field of ore dressing are presented here. Although monohydrate types of bauxites consist of finely dispersed minerals, however, in some cases certain contaminants (carbonates mainly), can be reduced by physical methods before Bayer process. Electronmicroscopy combined with computerized data processing is proven to determine the possibility of beneficiation and to control the different stages of ore dressing. Test results gained by Hungarian and Yougoslavian bauxite samples, contaminated by calcite, dolomite, siderite and pyrite, are discussed. Basic operations were: grinding (mostly dry) and classification, magnetic separation (mostly wet) and selective agglomeration. Only simple processes, having high efficiency and mostly dry ore dressing technique may meet the requirement of economical criteria. 1. [CONDITIONS OF ADAPTING THE BAUXITE DRESSING METHOD] Bauxite is a relatively cheap raw material, occurring in great bulks. Bauxite deposits may often lay far from the traditional ore processing plants, and in such cases the ore reaches the plants after long transportation. Some of these plants must face the difficulty that the resources of high quality ore are exhausted, they fall short of supply and, consequently, they must decide on whether to utilize the existing resources of poorer

Jan 1, 1984

By E. P. Fahrenthold, K. E. Gray

Introduction Brine reservoirs along the Texas and Louisiana Gulf coasts are currently under study to investigate the technical and economic viability of production wells designed to extract methane gas in solution. The effect of well pressure drawdown on reservoir rock and associated overburden material is important to well performance predictions and the analysis of potential subsidence problems. Consequently a series of compaction tests have been conducted on sandstone and shale cored from a test well drilled near Hitchcock, Texas, in order to determine the variation of mechanical properties to be expected over the producing life of the formation. Previous Work The referenced tests are part of an extended study of geopressured-geothermal reservoir behavior, including compaction (Jogi, Gray, Ashman, and Thompson, 1981 and Jogi, Kalra, Gray, and Thompson, 1981) and creep (Thompson, Jogi, Gray, and Richardson, 1981) tests of reservoir rock and related reservoir performance studies (Rago, Okhuma, Seperhnoori, and Thompson, 1985). Recent work has considered the nonlinear constitutive behavior of sandstone (Fahrenthold and Gray, 1985 and 19861, while additional experimental work is reported here. Geological structure and composition of the Hitchcock field from which the core samples were obtained is discussed by Light (1985). Experimental Procedure Compaction tests were conducted on cylindrical cores, nominally 2.75 inches in length and 2 inches in diameter, with independent control of the axial, confining, and pore pressures. Axial and radial deformation of the samples were measured in tests over a range of effective stress states expected to develop over the reservoir lifetime. The term effective stress as used here refers to the algebraic difference of the total stress and pore pressure, with compression taken as positive. Three types of compaction tests were conducted on the sandstone. In the uniaxial tests, axial total stress and radial strain were held constant as the pore pressure was reduced, similating one dimensional compaction which may occur during reservoir depletion. In the triaxial tests, radial total stress and pore pressure were held constant as the axial total stress was increased, duplicating conventional rock compaction test procedures. In the pore pressure drawdown tests, axial and radial total stresses were held constant while the pore pressure was reduced, in order to investigate differences in sample response to mechanical and pore pressure loading. Compaction tests were also conducted on shale material obtained from the reservoir overburden. The field coring process provided few consolidated shale sections sufficiently large to allow preparation of samples with the dimensions described above. With additional attrition during sample preparation of this brittle material, ultimate yield of the coring effort was limited. The few available samples were tested in uniaxial and triaxial tests similar to those described above. The use of displacement transducers to measure sample deformation avoided the difficulty of strain gauge installation on this material. Test Results The sandstone and shale both demonstrated nonlinear stress-strain behavior, with hysteresis and residual strain present upon unloading. Polynomial interpolation of the stress-strain curves was used in the calculation of incremental values for the loading and unloading moduli. Figures 1 and 2 show example axial effective stress-axial strain curves for triaxial tests conducted on sandstone and shale samples. The figures plot incremental stress and strain variables, defined as deviations from the state of prestress to which the sample was subjected. The state of prestress was varied between tests in order to investigate material behavior over the entire stress and strain space of interest. Tables 1 and 2 give the incremental moduli (Young's modulus and Poisson's ratio) as a

Jan 1, 1986

By J. C. Hower

The Hardgrove grindability index (HGI) is a widely used coal-quality parameter with applications in coal mining, beneficiation, and utilization. An understanding of the petrology of the coal is fundamental to understanding the validity of the HGI in the given application. The HGI varies with coal rank, increasing (greater ease of grinding) with increasing rank through the high-volatile bituminous rank range; and the HGI varies with changes in the maceral and microlithotype composition, decreasing with an increase in liptinite and liptinite-rich microlithotypes. In this review, the .fundamental relationship between HGI and coal petrology, and consequently its relationship to coal utilization, is examined.

Jan 1, 1999

By Allen V. Reicks

Modern conveyor pulleys are welded steel structures subjected to dynamic loads. In this paper, fatigue notch and fracture mechanics methods are applied to several weld joints on typical pulley constructions. These methods are used to analyze field applications and are correlated with laboratory testing. Generalized approaches are presented which provide high confidence in pulley design with corresponding high reliability.

Jan 1, 1996

By Herbert D. Drechsler

La financiación minera está inter-relacionada con los siguientes aspectos: "determinatión de los recursos totales a utilizar en una empresa minera; adjudicación eficiente de estos recursos a los varios multiples activos de la empresa; y obtención del mejor balance financiero en relación con la situación general de toda la compañia". La primera parte comprende un repaso de los problemas financieros a traves del estudio y análisis del Balance General y Cuenta de Explotación. La parte siguiente es una exposición de la naturaleza de los criterion desarrollados en el estudio de viabilidad. La tercera parte describe las fuentes de financiación del capital, y la parte final describe casos prácticos de financiación minera.

Jan 1, 1982

By Fathi Habashi

OXIDE ORES can be divided into two groups: 1) Simple oxides (Table 3.1). 2) Complex oxides. Those ores containing minerals composed of two oxides; an acid oxide (Cr2O3, Nb2O5, etc.), and a basic oxide (CaO, FeO, MnO), as shown in Table 3.2.

Jan 1, 1970

By J. F. T. Agapito

Energy West Mining operates the Deer Creek and Cottonwood/Trail Mountain coal mines in the Wasatch Plateau about 40 km (25 miles) southwest of Price, UT. The Deer Creek Mine extracts the Upper Blind Canyon seam and the Cottonwood/Trail Mountain Mine extracts the Hiawatha seam 12 to 36 m (40 to 120 ft) below. Both seams average about 2.8 m (9 ft) in thickness. Cover depths exceed 550 m (1,800 ft) in a large portion of the unmined reserve. Stability problems at Deer Creek are mostly due to coal bursts caused by high stresses associated with deep cover and sandstone channels. Most of the bursts have occurred in gate pillars and, to a lesser extent, at the longwall face and during development. The introduction of a two-entry gateroad system with 9-m- (30-ft-) wide yield pillars has been a major factor in controlling and minimizing gate pillar [ ] bursts (Agapito et al., 1988). However, some bursting began to occur in the 9-m- (30-ft-) wide pillars as cover depths reached 550 to 610 m (1,800 to 2,000 ft). This was due to more rapid and higher abutment loading in areas with very strong roof and stiff floor.

Jan 1, 1997

By Omar A. Muhtadi, David A. Milligan

7.1 INTRODUCTION The circulating fluid (generally an aqueous cyanide solution) is the major active component of heap leaching. This solution extracts precious metal from the heap and is then processed to recover the precious metal. The solution continuously recycles through the heap to recover more precious metal. With each cycle through the heap, water and chemicals are lost. Make-up water and chemicals must be added to balance losses from evaporation, seepage, entrainment, and chemical reaction in the heap, as well as any other processing losses. Adding more water than needed can result in a build-up of water as inventory in the various ponds and can eventually require that water be discharged from the operation. This is an extremely undesirable condition, and can often be very expensive in both investment in water treating facilities and operating costs. Most heap leach facilities operate under a zero discharge permit; thus, a situation requiring water discharge can result in permit violation. Chemical solution control must be managed to maintain the optimum pH, dissolved oxygen content, and cyanide content, while preventing "scaling". Calcium-based precipitation is a common scaling problem in mill reclaim waters. A buildup of these deposits can result in severe reduction of water flow, loss of pump efficiency and eventual interruption in metal production. In addition, problems of plugged sprinkler heads, blinded leach pads and fouled carbon (in carbon recovery systems) can be and often are experienced when scale control is not maintained. The remainder of this chapter discusses chemical solution control and scaling prediction/prevention in the context of a "closed" system. Sizing of ponds to accommodate precipitation and runoff, collection systems, and other similar design considerations are not discussed here. These topics are deferred to later chapters, e.g. Chapter 10 considers design of collection systems while Chapter 12 discusses pond sizing. 7.2 CHEMICAL CONTROL Chemical composition of the circulating solution must be controlled by the operator if the heap leaching process is to be successful. The primary or essential chemical control parameters in any heap leaching operation are:

Jan 1, 1988

By H. Nazeri, T. G. Rozgonyi

Many industries when volumes of the solid materials are large invariably relay upon the gravity to induce solids to flow out of storage, through channels and reactors. In mining industry ore pass’s requirements to less energy (only gravity) have made them very popular both in underground and open pit mines. This paper discusses the major findings of research on 2D Discrete Element Method simulation of gravity flow of ore in ore passes. Results show that ore characteristics, ore pass configuration can significantly affect loads (static, dynamic) on the gate assembly and creation of hang-ups.

Jan 1, 2003

By J. Engesser

A research project supported by the Minnesota Department of Natural Resources and the Iron Ore Cooperative Research Committee was undertaken to reduce the dissolution of fluoride into process water during taconite processing. Leach tests were conducted using rod mill feed samples and water containing varying concentrations of calcium and sodium. Laboratory liberation grinds were performed to evaluate fluoride rejection during grinding and magnetic separation. Tube furnace tests were conducted to evaluate fluoride volatilization during pellet induration. The results indicate that fluoride concentration of process water is a function of both calcium and sodium concentration in process water. It appears that less than 1 percent of the fluoride present in rod mill feed will dissolve in process water during grinding. More than 90 percent of the fluoride present in rod mill feed is rejected with tailings during size reduction and magnetic separation. The furnace tests demonstrate that bentonite and fluxstone (calcite and dolomite) addition to taconite concentrate during pellet production increases the amount of fluoride that volatilizes during induration. Lime hydrate addition to pellets decreases the amount of fluoride that volatilizes during pellet induration. During acid pellet production approximately three times more fluoride enters the water during induration-off-gas scrubbing than during grinding. When fluxed pellets are produced three to eight times more fluoride enters the water during off-gas scrubbing than during taconite grinding.

Jan 1, 2004

By R. W. Smith, D. L. Taylor, K. A. Altman

The importance of metallurgical information in reaching appropriate decisions during the development of mining projects is demonstrated. A financial analysis is calculated using discrete system simulation. The results are compared to the results of a traditional sensitivity analysis. The traditional analysis is shown to have the potential to overestimate the value of mining projects. The type of statistical distribution used in a random number generator affects the results significantly. The statistical method of analysis provides insight into the amount of metallurgical testing needed and provides verification of how representative the samples are.

Jan 1, 2002

By N. Magdalinovic

This paper analyzes the basic elements important for sustainable development in the sphere of metal mineral raw materials and offers one of the possible ways of defining the index of sustainable development.

Jan 1, 2007

By J. Bartrum, A. Bowler, G. Butcher

The purpose of this paper is to outline the design, specification, and operation of the 8.5-m- diam (28-ft-diam) SAG mill commissioned at Kidston Gold Mines during January 1985. Amenability of Kidston ore to SAG milling, coupled with substantial cost advantages, led to the specification of this mill, equipped with variable speed drive to overcome the large variation in ore hardness. Operation of the mill is effected via a number of automatic control loops. Problems experienced with automatic control plus other electrical and mechanical failures have led to design changes and the formulation of future operating strategies.

Jan 1, 1987

By K. H. McDaniel, K. G. Wallace

This paper describes the development of a Windows-based interactive mine ventilation simulation software program at the Waste Isolation Pilot Plant (WIPP). To enhance the operation of the underground ventilation system, Westinghouse Electric Corp. developed a program called WIPPVENT. While WIPPVENT includes most of the functions of the commercially available simulation program VNETPC from Mine Ven- tilation Services Inc. and uses the same subroutine to calculate airflow distributions, the user interface was completely rewritten as a Windows application with screen grap-hics. WIPPVENT is designed to interact with WIPP ventilation-monitoring systems through the sitewide central monitoring system. Data (e.g., air quantity and differential pressure) can be continuously collected from the underground ventilation remote-monitoring and control system and from the mine's weather stations (psychrometric data). Furthermore, WIPPVENT incorporates regulator characteristic curves specific to the site. The program utilizes this data to create and continuously update a real-time ventilation model. This paper discusses the design, the key features and the interactive capabilities of WIPPVENT.

Jan 1, 1998

By J. D. Miller

Fluid flow phenomena and therefore the flotation efficiency of air-sparged hydrocyclone (ASH) flotation are strongly dependent on operating and design variables such as air and slurry flow rates, underflow and overflow opening areas, percent solids of the feed, reagent levels, particle size and ASH length. Time-averaged multiphase flow characteristics, as determined by X-ray CT (described in a previous publication), are used to understand and explain the steady-state ASH flotation of quartz. A detailed parametric study of quartz flotation by a nominal 2in. diam. air-sparged hydrocyclone (ASH-2C) revealed the influence of these variables on the flotation response, which is discussed in terms of the multiphase flow characteristics. Thus, a phenomenological description of quartz flotation has been established to assist in the further development and utilization of the ASH technology.

Jan 1, 1996

By Tom Bruington

This paper discusses the accuracy of determining the quantities of gold and silver on activated carbon in various stages of process for typical precious metals flowsheets. Accurate plant performance evaluation depends upon reliable estimates of carbon and precious metals inventories. The sources of sampling error are identified and methods of reducing them discussed. Several case studies illustrating the sensitivity of flowsheet performance to sampling error are presented.

Jan 1, 1991

By S. G. Malghan, D. Santhiya, S. Subramanian, K. A. Natarajan

The adsorption of poly(vinyl alcohol) (PVA) of molecular weight 25,000 onto alumina was studied as a function of pH. The adsorption isotherms were also determined. The adsorption density increases with increasing pH, while the isotherms are rounded and of the low affinity type. Electrokinetic studies indicate that the electrophoretic mobilities are reduced in magnitude in proportion to the PVA concentration, without any shift in isoelectric-point (iep). This resembles the influence of an indifferent electrolyte. The calculated values of the free energy of adsorption between alumina and PVA are suggestive of hydrogen bonding. FTIR spectro-scopic data provide additional evidence in support of hydrogen bonding.

Jan 1, 2000

By Jeff W. Butwell

Mill flotation tailings impounded at the Gooseberry Mine site between 1976 and 1984 were determined to be an economic source of gold and silver recoverable by standard heap leach technology in conjunction with feed agglomeration. Metal recovery at 85 percent Au, 75 percent Ag is attained on properly agglomerated (pelletized) tailings which average 85 percent -75 micron. Because the impounded tailings averaged over 18 percent moisture (32 percent moisture maximum at depth) in place behind the storage dam, the mining method, mixing and agglomeration technique, and materials handling practice were major considerations in making this operation a financial success.

Jan 1, 1990

By David Royston

Conventional straight-radial SAG mill pulp lifters suffer from incomplete discharge of the rock portion of the charge. The resulting backflow of undischarged rock limits pulp lifter performance and is the major source of wear in pulp lifters. Backflow is increased in pulp discharge cone systems where multiple channels converge towards the central diversion cone. This paper covers recent experience with pulp lifter and discharge cone design supported by a single particle motion model that illustrates the discharge and backflow characteristics of pulp lifters, including the impact of discharge cone configuration.

Jan 1, 2005