Search Documents

By C. E. Brechtel

Bench cut-and-fill stopes with heights between 85 and 105 ft are being excavated in the lower levels of the B-NEATH Zone. Estimates of pillar strength and pillar loading indicated a high probability of pillar failure. Some changes in mining practice were made to minimize impacts of pillar failure and a rock mechanics instrumentation program was employed to monitor stability during mining of the first stopes. Limited pillar failure, in the form of destressing, was observed in the initial stopes; however, global stability during mining was good. Instrumentation data indicated that predictions of pillar strength and stress were quite close to field results.

Jan 1, 1989

By V. Rastogi

Surfactant-based bactericides are able to control acid formation in sulfidic materials such as pyrite and sulfidic ores, thereby helping to abate acid rock drainage. Bactericides are used in the following two ways: as periodic or continuous spray treatments for the prevention of acidification of material actively handled and moved and in controlled-release form for reclamation. Site-specific bactericide treatments are designed for active sites and reclamation. Results from two active coal refuse sites show that acid production can be reduced by 88% or more. Results from reclaimed sites show that bactericide treatment can be more effective than the addition of alkaline materials such as limestone and can reduce acid production from 3,500 to <30 ppm. The controlled-release-pellets treatment outlasts the life of the pellets, as shown by a study of a site now 10 years old A single treatment sets up a change in site microbiology to replace acid-producing Thiobacillus ferrooxidans bacteria with heterotrophic bacteria and creates a stable site without the need for further treatments. A secondary beneficial effect of bactericides is on revegetation, and biomass from treated areas is almost 10 times that from areas not treated with bactericide. Depending on the application, bactericide treatment can be cost effective upfront and certainly long-term, compared to the perpetual water treatment that could be required, even after productive use of the site is completed

Jan 1, 1997

By Steve Kral

The list of environmental issues facing industry in general, and the mining industry in particular, has placed greater emphasis on the concept of risk assessment and risk management. In informal terms, risk can be defined as the chance of injury, loss or damage. More formally, it is defined as the probability of an occurrence and its consequences. In simple terms, risk assessment involves three questions: What can go wrong? How probable is it to go wrong? If it goes wrong, what are the consequences? Experts on the subject of risk assess¬ment and management met in St. Louis, MO in October 1992 to discuss the extensive and innovative technology that has been developed in this arena. Each agreed that a consistent framework can be used to approach risk assessment/ management considerations in siting and design alternatives, as well as when considering financial aspects of mine development. And the environmental planning process for mines, as well as planning for operation through closures, will rely more heavily on risk assessment and management techniques. Risk assessment is a tool to assist engineers, scientists and managers make better, defensible operational decisions. A realistic and probabilistic risk analysis, coupled with a sound financial model, can combine a large set of alternatives and criteria to arrive at a defensible decision. Organizers of this regional SME conference believe that mining professionals should become fully conversant with risk assessment techniques and approaches because this arena provides opportunities to develop more rational decision-making techniques. Current health risk assessments rely heavily on Environmental Protection Agency (EPA) approaches. Several speakers and papers show how this approach has been applied to a variety of topics. Two major advantages come forward when applying risk assessment techniques to environmental clean-up options for contaminated sites. They are the selection of practical options and cost-effective alternatives. A probabilistic risk assessment provides results that can be directly related to clean-up costs. It has been shown that small reductions in risk are obtained for large increases in cost after a certain threshold value is reached. A preferred, practical clean-up alternative that provides permanent solutions can be selected based on a probabilistic assessment. Here are summaries of some of the papers presented at the meeting.

Jan 1, 1993

By Chas. F. Jackson

INTRODUCTION This paper is one of a series dealing with mining methods and costs, prepared and published under the sponsorship of the US Bureau of Mines (USBM) and made possible through the cooperation of many mining companies in the US and foreign countries. The data presented have been obtained from papers previously published by the Bureau dealing with indi¬vidual mines, from the technical press, and from infor¬mation furnished by the mining companies. DEFINITIONS Top Slicing The term top slicing is commonly applied to that method of mining in which the ore is extracted by a series of timbered slices, beginning at the capping; the slice is caved, bringing down the capping to the floor of the slice; the succeeding lower slices are mined up to the overlying mat or gob, consisting of an accumulation of timber from the upper slices and broken capping, which follows the mining progressively downward (Fig. 1). The term has also come to be applied to the mining of ore bodies only one slice thick, by a series of tim¬bered slices one beside the other. The timbers are blasted out, bringing the capping down to the floor, suc¬ceeding slices being driven alongside those already caved (Fig. 2). In USBM classifications of mining methods, top slic¬ing has been placed under the heading caved stopes. The method differs fundamentally, however, from the cav¬ing methods of mining in which the breaking of the ore itself is accomplished by caving action induced by undercutting. In top slicing the ore is broken by the ordinary methods of drilling and blasting, and only the capping is broken up by caving. Main Levels or Haulage Levels Main or haulage levels are the main extraction levels on which the ore is hauled to the shaft. These levels and the shaft constitute the preliminary development of the mine.

Jan 1, 1982

By A. L. Mular

Si define la simulación digital y las técnicas de simulación son revisadas. La metodologia tipica conlleva la selección de modelos, el ajuste o reajuste de los datos primarios, la selección de una estrategia de acoplamiento, la valoración de la precisión del modelo en un sentido estadistico, y el desarrollo de estructura de simulación ejecutiva. La simulación sirve de ayuda para los ingenieros de procesos para evaluar la viabilidad de un esquema de flujo propuesto y el efecto de la modificación de un flujograma ya existente. Por otro lado, la simulación juega un papel importante en la optimación "off-line" y en la evaluación de estrategias de control de circuitos alternativos. Son presentados varios ejemplos para ilustrar estas utilizaciones para la simulación, incluyendo aplicaciones en los circuitos de trituración, circuitos de molienda y circuitos de flotación. Es de opinión de los autores que, dentro de la próxima década, las plantas de proceso de minerales serán estudiadas rutinariamente a través de una simulación digital durante las etapas preliminares de diseño. La simulación constituirá un importante componente en la toma de decisiones de un proceso.

Jan 1, 1982

By M. T. Worley

Joint Development Associates International, Inc. (JDA) began humanitarian relief and community development in Central Asia in1992, following the collapse of the former Soviet Union. Appropriate technology has played an important role in their efforts to assist those segments of society that are most vulnerable to poverty and disease. Three case histories are described to illustrate the successful implementation of simple, but effective technology in community development.

Jan 1, 2004

By Richard L. Coleman

El trabajo de ensayo metalúrgico para desarrollar un flujograma es el que ahora describimos, comenzando con una información experimentada requerida en todo momento hasta llegar a un esquema final de flujo de un proceso. Tanto las pruebas de laboratorio como de planta piloto son revisadas adecuadamente sobre las experiencias anteriores.

Jan 1, 1982

By Gonzalo Barrientos

Instrumentation and observation of real mine structures helped define the pressure arch at White Pine, a large copper mine in sedimentary rocks. The pressure arch, which is attributed to inherent horizontal stresses, is used in the design of mine openings.

Jan 1, 1969

By Ingvar Janelid

During recent years, numerous articles have been published regarding theories and practical applications of sublevel caving. The reason is the great interest this method has created through its possibilities of standardizing and mechanizing operations and equipment. Other advantages are that the method can be adapted to orebodies of different shape, size, strength etc., and especially that working conditions can be made safe and relatively comfortable since all work is carried out in drifts. As is well known, the disadvantages or sublevel caving are that ore recovery hardly exceeds 85-90 % if waste rock dilution is to be kept below 20-30 %. Therefore, the main research and development work has been concentrated on parameters which can affect and reduce these disadvantages. This paper deals only with principles and problems which apply to large, massive orebodies. The problems with narrow, vertical or inclined orebodies are so different that they require a special handling. In my opinion, the intense research and development work during recent years, combined with practical experience, has given enough knowledge of the influence of different parameters, so that normal sublevel caving can be efficiently planned.

Jan 1, 1975

By A. M. Elmherig, M. R. Sunu, R. N. Singh

The presence and orientations of fractures and discontinuities in rock masses exposed in a surface mining excavation are likely to have a great influence on both slope stability and blasting efficiencies. The classification of rock materials requires detailed investigations which are of interest to the design engineer. In designing a safe mining excavation, an engineer must take a number of decisions regarding face support and orientation based on the evalu¬ation of local strength and structural conditions encountered. The description of rock masses requires information additional to the properties of the rock material, discontinuities and other characteristics of engineering importance. Such information involves the acquisition of the following data: The description of the rock mass with reference to major geological structures. The orientation, nature, spacing and persistence of discontinuities. Degree of weathering. A critical review of rock mass classification systems and their application to surface mine excavation design and stability analysis is presented. The field investigation techniques for collecting rock mass data are described together with the techniques of analysis and presentation of data. Laboratory tests are carried out to determine intact rock strengths and deformation parameters of rock. The paper presents two case studies from the British hard rock surface mining industry to illustrate the application of the rock mass classification systems to stability analysis and excavation design.

Jan 1, 1986

By Marek Niec

Native sulfur deposits in Poland occur in Upper Miocene strata on the northern (platform) border of the Carpathian foredeep. Systematic exploration since 1953 has resulted in the discovery of seven stratifom-stratibound sulfur-bearing limestone deposits that together contain about 0.6 billion tons of demonstrated sulfur reserves and about 0.5 billion tons of inferred and hypothetical resources. One open pit and three Frasch mines are currently in operation; another is under construction and one has been abandoned. Total production is about five million tons per year from ore containing on the average about 25% sulfur. Field, isotope, and micropaleontological data indicate that the sulfur-bearing limestone was formed through the bacterial reduction of gypsum in the presence of methane discharged from source beds and traps in the Carpathian foredeep. Subsequent recrystallization of the sulfur-bearing limestone, tectonic activity, jointing, karstification, and partial leaching of the sulfur has transformed the sulfur deposits and has altered the thickness and content of the sulfur-bearing strata, and their porosity and permeability, affecting the productivity and water consumption of the sulfur wells. Caputerized borehole logging techniques and geostatistical reserve estimates are used in mine planning. Great environmental impact constrains the development of sulfur mines.

Jan 1, 1992

By R. Kadeg, S. Pavlou

A methodology for developing and utilizing risk-based action levels for soils in site closures is discussed. The methodology is based on standard exposure pathway models which are consistent with current regulatory guidance on conducting risk assessment. A simple approach to evaluating the potential for contamination ground water from the projected criteria based on the Toxicity Characteristic Leachate Procedure (TCLP) is also presented.

Jan 1, 1992

By S. D. Thompson, J. C. Dzurino

This investigation mainly focused on designing a bunker system for a large underground coal mine. The primary purpose of this bunker system was to keep high- and low-sulfur coal segregated on the underground belt system. These bunkers were also required for protecting the mine faces from out by belt delays. Methodologies used in developing this plan are briefly discussed. The final design and the procedures formulated for implementing it are also presented.

Jan 1, 1987

By Haydn H. Murray

Common clay includes a wide variety of clay and other fine- grained rocks that are used in many ways. These clays are some- times classified as miscellaneous clay and shale. Most products made from them are fired and include such things as structural and face brick, drain tile, vitrified pipe, quarry tile, flue tile, conduit, pottery, stoneware, and roofing tile. Very large tonnages of these materials are bloated by firing to form lightweight aggregate, and large quantities are used in making portland cement (see the specific chapters in this volume). Uses not requiring firing of a finished product include filler for paint and other products and shale and clay used for packing dynamite in blastholes and for plugging oil and gas wells that are no longer in use.

Jan 1, 1994

By R. Gong, R. Bhaskar

The development of a three-dimensional mathematical model for evaluating airflow fields at a continuous miner face is described. The model utilizes three-dimensional incompressible flow, mass continuity, and momentum (Navier-Stokes) equations to predict the airflow velocity at the face. Obstacles and equipment in the face area are modeled using appropriate boundary conditions. Parameters such as flow velocity and face dimensions can be modified and evaluated for various schemes, such as exhausting and blowing ventilation, using either brattice or tubing. A model such as the one described, with additions for local effects, can be used to evaluate novel face ventilation ideas before initiating expensive full-scale tests or field studies. The model described is a step in the direction of advanced predictor models.

Jan 1, 1993

By Michael J. Rinker, R. V. Nicholson

Waste rock and tailings from a proposed nickel-copper mine were evaluated extensively for potential on-land and under water disposal. Standard humidity cell and column tests were conducted over a two year period and underwater tests were conducted for more than one year. Nickel concentrations or release rates from the waste were consistent with nickel to sulphur ratios in the solids. This relationship provided a tool to assess the risk of metal leaching in wastes using nickel and sulphide assays. Nickel release and mobilization was found to occur for both oxidizing leach tests and under water tests even when pH values exceeded 7.0. Geochemical model calculations showed that iron oxyhydroxide solids can scavenge nickel from leachate and that the nickel inventory can be released from solids at relatively lower, but neutral pH values.

Jan 1, 2000

By J. K. Mokka, P. D. Rao, H. K. Lin

Extensive exploration has resulted in delineation of a massive sulfide district on the north flank of the east-central Alaska range. The district covers approximately 400 mi2 and contains numerous stratiform, transposed and some replacement type sulfide deposits ranging in size from less than 1 million st to 20 million st. Five types of ores were sampled for the study. Mineralogical analysis revealed that the minerals are too fine grained for conventional grinding and beneficiation. Hydrometallurgical studies were conducted using ferric chloride as a lixiviant. Ore microscopic studies as well as electron microprobe analyses of minerals in the raw samples and leach residues explained the low recoveries for certain elements as well as sources of impurities that need to be eliminated from the process streams.

Jan 1, 1992

By George L. Baloo, Dave Kwiatkowski, Jose G. Cañlzales

Capital project funding for a medium to large materials handling project often includes a budget for procurement of supplier-recommended spare parts, and it is the Project Team&apos;s responsibility to select these parts. With today&apos;s economic climate, limited budget, and other factors, the spare parts selection process is a difficult and arduous effort. This decision carries with it a risk to plant operations and in some cases the commodities producers. Too often the decision-making process is not documented, and the reasons for eliminating and reducing quantities are based on "best guess " Recently on the Solids Handling Phase 2 Project in Jose, Venezuela, the Project Team took a unique approach to this problem. This paper discusses the analytical approach taken by the Project Team, the database system that was developed to manage this problem, lessons learned, and their applicability to pre- project planning and preliminary design.

Jan 1, 2004

By S. K. Kawatra, T. C. Eisele

To reduce their sulfur emissions, many coal-fired electric power plants use wet flue-gas scrubbers. These scrubbers convert sulfur oxides into solid sulfate and sulfite sludge, which must then be disposed of. Currently, the major markets for scrubber sludge are for manufacture of gypsum products, such as wallboard and plaster, and for cement. However, the quality of the raw sludge is often not high enough or consistent enough to satisfy manufacturers, and so the material is difficult to sell. Other markets, such as paper manufacture and plastics fillers, have even more stringent quality requirements and will not accept raw sludge at all. In the work described in this paper, several reagents have been examined to determine their ability to selectively improve the flotation of the unreacted limestone contaminant away from the desirable products (calcium sulfite and gypsum). The most success has been achieved using a cationic collector, which shows a higher selectivity between calcium sulfite and calcium carbonate than do the anionic collectors that were studied.

Jan 1, 1995

By Michael D. Balen

The plate-glass windows in the bus were cracked and mud-coated. Nevertheless, they afforded an excellent view of the many head-on collisions we narrowly avoided along the route from the Magadan airport to town. Apparently the driver thought the left side of the road was smoother than the right side, for he drove in the wrong lane at all possible times, even in the face of oncoming traffic. As far as we could tell, neither side of the road was any better than the other. Either way, we had to hang on just to stay in our seats. We careened past trucks and pedestrians, nearly always in the face of impending disaster. When the bus finally pulled into the parking lot of the Okean Hotel in Magadan, we had to thank the driver, not only for safely delivering his passengers, but also for the lasting first impression he gave us of the Russian Far East.

Jan 1, 1995