Search Documents

By C. John Dunnicliff, Birger Schmidt

INTRODUCTION To be effective and useful, monitoring of tunnel construction must be carefully planned throughout all steps. A vital and frequently overlooked step is a clear definition of the specific purposes of the instrumentation. Most tunnel construction monitoring has in the past been of benefit to research, the advancement of tunneling practice, wittingly or not. The development of monitoring instrumentation for the benefit of the project from which the data are recovered has very significant potential for risk and cost reduction of soft ground tunneling. A systematic approach to tunnel construction monitoring, from conception to full implementation, includes at least the following nine tasks or steps: Definition of benefits and purposes; design and project specification to draw full benefits; selection of monitoring parameters; selection of instruments and writing of specifications for procurement and installation; procurement and installation; reading and maintenance; data storage and retrieval; interpretation; implementation. Some of these steps are fairly easy and resolved through the use of established theories and technologies. The difficult ones are those that require the bending of minds, those that involve changes in the ways engineers design soft ground tunnels, the way owners pay for tunnels, and the construction is managed, inspected and controlled. Performance monitoring can be of benefit to the owner, design

Jan 1, 1974

By F. Allen Meek

The Upshur Complex of Island Creek Coal Corp. consists of approximatly 35.000 acres of both surface and deep mine researves located in Upshur County West Virginia. The principle seams on the researve are the Middle and Lower Kittanning. Other mining in the area during the late 1960's and early 1970's produced surface mines that exhibited severely acidic drainage characteristics both during the mining phase, and after reclamation was completed. The Buckhannon River, the principal drainage for the area, is a high quality, lightly buffered stream, that is periodically stocked with trout. Because past mining had caused post mining acidic discharges and the Buckhannon River was a valuable recreational resource, mining permits for the area were put on hold by regulatory authorities, until solutions to the acid mine drainage questions could be addressed. In 1978, the director of the West Virginia Department of Natural Resources appointed a Task Force consisting of Industry, Regulatory. and Academlc participants. This Task Force was charged with gathering information and evaluating field procedures used during mining to prevent acidic mine drainage. In 1979, the group published a document titled "Suggested Guidelines for Mining in Potentially Acid Producing Overburdens" which summarized material handling and mining procedures that could be employed to help prevent the occurrence of post mining acid mine drainage. In 1982, a Technical Advisory Committee was appointed consisting of well known researchers in the field of acid mine drainage prediction and prevention. The group was charged with the task of conducting research in the field of acid mine drainage prevention. Mining conducted at the Upshur Complex between 1979 and 1986 employed various acid mine drainage preventative techniques recommended in the suggested guidelines manual and techniques concurrently being researched by the Technical Advisory Committee. Costs for the various techniques were documented and the resulting post-mining water monitored. The results of these evaluations are used by Island Creek in the planning of future mining operations in potentially acid prodcuing environments

Jan 1, 1991

By Guillermo P. Salas

The Consejo de Recursos Naturales No Renovables of the Mexican government entered into an agreement with the United Nations in 1964 for the mineral exploration of a large area in Estado de Sonora, Mexico. The agreement called for a systematic exploration for copper in northern Sonora based on photogeologic mapping, aerial reconnaissance, and geochemical stream sediment sampling. The UN-CRNNR investigations resulted in the detection of anomalous copper values in sediment from the Arroyo Cruz de Cafiada. The anomaly was followed upstream to its source, which ultimately proved to be the La Caridad ore body (see Fig. 1). Soil copper and molybdenum values were found over a large area, and further detailed geologic and geophysical investigations were instituted of the anomalous area. David Coolbaugh was largely responsible for the follow-up work. An induced polarization (IP) survey found a roughly circular region of "highs" that coincided with a high soil copper anomaly. The circular anomalies ringed the topographic feature that ultimately was found to contain the Caridad ore body. Soil geochemical copper response over the ore body was subdued, because the soils were derived from a leached capping, whereas leaching in fringe areas that contained less veining was less intense. The ore body was also ringed by the typical high pyrite zone, and this was the anomaly detected by the IP survey. The UN began drilling in the fall of 1966. Eleven holes tested the IP-Cu geochemical high, but none were of commercial interest. The project was returned to the Consejo and was reviewed in the field by G.P. Salas and V.F. Hollister. It was found that the leached capping had not been tested by the past activities, and the Consejo elected to explore that area in 1967. The capping was evaluated by Salas and Hollister and drilling by the Consejo began in 1967. Commercial grade ore intercepts were found in the first hole. The Consejo drilled nine holes, of which eight were commercial. At least 90.7 Mt (100 million tons) of 0.8% copper were indicated by the Consejo in eight holes. The lesson learned in this discovery is that evaluation of leached capping is an important guide to exploration. The general-

Jan 1, 1991

By James I. Mathis

Should an arbitrary reduction factor be applied to laboratory compressive strengths when designing pillars? The answer is, as is the main contention of Peng's article, probably not. Many factors affect the strength of the material remaining in the pillar. On the other hand, outside influences will influence the strength testing results from the lab. This is not the first article, nor the last, to discuss the discrepancy between the two strengths. As was discussed in the article, actual pillar strength is affected by several factors. The two mentioned were: • The scale effect of discontinuities. How large must the pillar be so that the increase in discontinuity count with size will not decrease the strength. • Non-uniform strengths and lithologic units within the pillar. The scale effect of discontinuities is important. What size block must be tested so that the rock mass strength is actually measured? For a highly fractured rock mass, or coal with a high cleat density, this sample may be quite small. Conversely, if an unaltered, moderately jointed, quartz monzonite was examined, the sample block would likely be very large. This is the subject of ongo¬ing research. More to the point, if the tested sample is sufficiently large to model the rock mass strength, then no reductions should be made in the lab strength based on this factor alone. Non-uniform strengths and variations in lithologic units will also affect the pillar strength. I am not an expert in coal mines, having gained my experience in hard rock metal mining. These problems, though, are commonplace. However, strength sampling for pillar strength determination involves sampling material from within the lithologic unit that will form the pillar, not from pieces of material found on the floor. In addition, this sampling should cover the entire range of strengths of the material in the pillar-hard units (such as the partings described by Peng), as well as soft units. Testing results should then be included in the pillar design. Contrary to statements in Peng's article, at least one rock mass rating system (Laubscher, 1990) allows for the compositing of strong and weak units into a design rock mass strength that can be used for pillar design.

Jan 1, 1993

By David Whitehead

My qualification to speak on the globalization of the the mining industry comes from having worked in the industry in Europe, North and South America, Africa and Australasia in positions ranging from exploration geologist to chief executive. For about a third of my career I have lived and worked in the Southern Hemisphere. And for much of the rest of my career I have been involved in or responsible for activities in the Southern Hemisphere. This has given me the opportunity to experience globalization from the sharp end, as it were. This means speaking English with an Australian accent, Spanish with a Chilean accent, French with a West African accent and Dutch with an English accent. My topic is globalization, especially of the mining industry from a Southern Hemisphere perspective and specifically the experience and history of Gencor in that context. First, I will say a little about what globalization means to the southern part of the world: How and why the South differs from the North and how the challenge of globalization affects a south-based company differently than a northern one. I will also detail how Gencor has made significant progress in globalizing through the acquisition of mining assets from Shell. As Fig. 1 shows, I have divided up the world into northern and southern components, rather than hemispheres. The southern world comprises mainly countries that have emerged from the status of economic - if not political - colonies of nations such as England, Spain, Portugal, France, the Netherlands and, surprisingly, Italy and Germany. I have not considered the Indochinese and Arabian peninsulas in my southern world. The emergence of the. former is still in its early stages while the latter is clearly a part of the northern economic system. Large parts of Africa and South America are geometrically in the Northern Hemisphere but economically in the southern world. The reverse is the case for the IndoPersian peninsula. With the distinguished exception of Australia and South Africa, most of these countries nationalized their mining industries and mineral patrimony after attaining political independence. A major element of the globalization of the mining industry is related to the privatization of the mining industry in these countries and to the opening up of their min¬eral patrimony to non-national exploitation. The Southern Hemisphere is the watery part of the world. It is almost three quarters ocean as against a slight preponderance of land in the north. Economically, ocean areas have only a fraction of the productivity of land, except in a few oil-rich areas like the Gulf of Mexico and the North Sea. The consequence is that even on an economically level playing field we would expect the south to generate only about one third of the world's economic product.

Jan 1, 1997

By T. F. Deems

The nature, usage and comparatively rare occurrence of ball clay is described. The importance of these white firing plastic clays in ceramics, particularly in the production of industrial sanitary ware and tiles, is emphasized. The US deposits are briefly discussed. What is known about relevant deposits in Brazil, Argentina, Colombia and Venezuela (the four largest ceramic producers in South America) is also described. The ceramic plants have been sited near the centers of population rather than the plastic clay deposits. At present, extraction is probably concentrated on surface residual deposits and lenses which require minimum investment. Native plastic clays are used exclusively in the tile plants, but in sanitary ware, they are often used as extenders of imported ball clays.

Jan 1, 1997

A panel discussion on carbon-in-pulp processing of gold and silver ores was one of the highlights of the 1981 AIME Annual Meeting in Chicago. The session generated considerable interest and discussion among panelists and the audience. For those unable to attend the panel, the program was recorded and the discussion appears in this two-part report. The panel was co-chaired by Robert S. Shoemaker, vice president of San Francisco Mining Associates, and Laurence D. Hartzog, principal engineer with Bechtel Civil and Minerals Inc., San Francisco, CA. Panel members included: George Potter, consultant, Tucson, AZ; Kenneth B. Hall, metallurgical superintendent, Homestake Mining Co., Lead, SD; and Donald M. Duncan, resident manager, Pinson Mining Co., Winnemucca, NV. There have been several types of carbon-in-pulp adsorption vessels in use, such as the Dorr-type agitator, the simple propeller agitated tank, the Pachuca tank, and, lately, the draft tube-type of agitated tank. Which one of these is best and why? Potter: On the selection of the most appropriate adsorption vessel, there is a considerable difference of opinion that stems largely from the fact that every ore is different. The mesh of grind, the pulp solids, and the apparent viscosity of the pulp as caused by its clay content and chemical conditions all differ. The traditional Dorr agitator with the slow speed center sweep and either peripheral or center column air lifts has worked quite well on the finer grinds of all minus 65 and probably 70-80% minus 200 mesh. Pachuca tanks have also been successful and they may be capable of handling a coarser feed than the traditional Dorr tank. One uranium mill, for example, handles minus 28 mesh sandstone ore in a Pachuca. The most recent development and one that commands consideration is the draft tube agitator in which there is a turbine which closely fits inside a draft tube. Velocity in the tube is carefully calculated to avoid undue shear and thus abrasion of the carbon. The objective in all cases, of course, is to mix the granular carbon, which is typically 6 x 16 mesh, very gently but thoroughly in a slurry with minimum carbon abrasion. I do not know that there is one outstanding choice just yet and I have been unable so far to get information on C-I-P service for ore grinds as coarse as 35 mesh. Duncan: The major advantage of draft tube-type is the ease of startup. At the Pinson plant we installed draft tube-type agitators but it is too early to quote experience with them. We also haven't operated long enough to determine just what our carbon loss is. The advantage, of course, in the draft tube design is that it requires only about one-third the horsepower input of a conventional agitator. If it has no other advantages, it has that. Hall: The type of vessel most suitable for C-I-P adsorption depends on the type of ore treated and the prevailing operating conditions. In most cases, a deep tank with turbine-type mechanical agitator and low speed tip velocities would be satisfactory. Turbine-type impellers give a positive type of agitation which assures optimum ion contact and reduces short circuiting. Thorough aeration is possible with an air sparge properly located. A mechanical agitator can easily be started up after an outage, but it is usually necessary to drain and wash out a Dorr rake-type or Pachuca before restarting. The turbine-type impeller requires more power, but maintenance costs are negligible if rubber covered impellers are used. Carbon losses are minimal. In smaller plants, Pachuca type agitators provide adequate aeration and agitation. Bob Polak, Occidental Minerals (from the floor): Mr. Hall, you favor the mechanical-type agitator with the preface that the proper design is critical. Could you elaborate on this for us? Hall: The most important thing is low tip speed to prevent carbon attrition. I think the impeller should be sized so that you get a good sweeping action toward the bottom of the tank, across its bottom, up the sides, and back to the center. The advantage of the draft tube is that you get a more positive agitation and you probably get improved aeration too. Polak: Do you know of anyone using an upflow mechanical agitator rather than a downflow unit? Hall: I think that Bob Wilson at Custom Equipment has designed one where he has located the sparge directly beneath the impeller. The air bubbles are broken up by the impeller as the slurry passes through it. The slurry flows upward, outward, down the sides, and, again, back to the center of the tank. I don't know that any tanks of this design are in commercial use. Hans Von Michaelis, Randol International (from the floor): A question to any of the panelists on flat bottom versus conical bottom Pachucas. Hall: I would say the conical bottom would be most suitable in most cases. Some plants have experienced problems with flat bottom Pachucas in that they have a tendency to sand in on the sides of the tank so only the center of the tank is active. Duncan: With our draft tube tank we placed an inverted cone in the center of the tank bottom and blanked off the bottom comer around the circumference of the tank to facilitate movement of the pulp. Other than that, as far as conical bottom tanks are concerned, I'm generally opposed to them because of the cost and height differential. Larry Kramer, Kennecott Minerals Co. (from the floor): Mr. Duncan, you mentioned that the draft tube-type could be agitated with about one-third the horse-power applied to a conventional propellor agitated tank. I have trouble trying to pin down that kind of number. Could you give a bit of rationale as to why that mechanism has a lower horsepower requirement? Duncan: I think it has to do with the fact that below the propeller you have straightening vanes. The pulp, which is flowing vertically downward, is turned and flows upward again without any recirculation. You have an inherently less horse-power requirement in that type of tank. The one-third horsepower requirement is a number I obtained from Lightnin, which supplied us with details of the draft tube. There is probably much more recirculation with a conventional impeller type that is wasted motion. Potter: Last week I saw some agitators in South Africa with short draft tubes and actual turbine-type impellers. This plant was handling 200 kt of ore per month. The tanks were flat bottomed, and the agitation appeared to be quite satisfactory.

Jan 8, 1981

By W. M. Pytel

A simplified two-dimensional model to analyze time-dependent load distribution and surface subsidence associated with longwall mining geometries is described. The model is based on the theory of beams resting on inelastic foundations and includes visco-elastic behavior of immediate floor strata, non-linear behavior of coal pillars, elastic behavior of face supports, and visco-elastic behavior of the overburden strata. The relative importance of the different variables affecting the performance of longwall mining geometries from ground control point of view is also analyzed. The model has been validated for field observations from one Illinois longwall mine.

Jan 1, 1986

By Andrew I. Hustrulid

The Internet and World Wide Web create multiple opportunities to advance and change an industry. Scandura Conveyor Belting, a mid-sized manufacturing company supplying the mining industry, has embraced several of these opportunities that add value to the sale and service of the manufactured product. This paper presents a technical overview of available technology and how it is being applied to advance the conveyor belt industry. These technologies are used to provide historic catalog information, interactive troubleshooting, product installation and service instructions, detailed product information, technical calculations for the proper conveyor belt selection, and on-line site surveys and maintenance logs.

Jan 1, 2002

By J. B. Rubinstein, V. J. Badenicov, S. T. Hall

A simulation technique of the flotation process and models for the solution of various problems are developed. A modular model of column flotation is constructed taking into account the kinetic relationship of the process and the hydrodynamic regime in the cell. Based on this, a technique of calculating the column parameters based on laboratory tests is developed (scaling-up), and applied for calcetest results is developed (scaling-up), and applied for calculating the design of commercial-scale columns.

Jan 1, 1996

By Gennaro G. Ph. D Marino

In order to improve handling of subsidence damages the Illinois Mine Subsidence Insurance Fund supported the development of novel cost-effective methods of repair. The research in developing the repairs was directed towards the most common and costly damages that had been observed. As a result repair techniques were designed for structurally cracked foundations in the tension zone; structurally cracked foundations in the compression zone; and damaged or undamaged tilted foundations. When appropriate, the postulated methods would result in: 1. significant cost savings (over conventional procedures); 2. a structural capacity greater than when the foundation was untracked; and 3. an aesthetic appeal. All the postulated repair methodologies were laboratory and/or field tested. The paper will summarize the essentials of each technique developed and the test results.

Jan 1, 1986

By H. T. Mulryan

Talc is used as an essential ingredient in a variety of plastics applications ranging from polyester body patch compounds through polypropylene automotive, appliance and household furniture components to high performance parts made from liquid crystal engineering resins. This paper focuses on polyolefin applications, the three-tier market for talc in polypropylene, the effects of various tales in typical compounds and trends in each market segment. Emphasis is given to emerging markets, examples of which are polypropylene compounds that mimic higher cost resins, and polyethylene films. Customer requirements, for tales for these purposes are discussed.

Jan 1, 1993

By Paul Chamberlin

Management has assorted roles to play, many of which are listed, that may call for consultant input. Consultants also play various roles, and some of these are discussed as well. The relationship between management and the consultant depends mainly on management's preparation for the assignment and on their monitoring during the assignment. Consultant costs are discussed briefly and suggestions for keeping consultant costs under control are given. In addition, some qualities of a good consultant are covered.

Jan 1, 2001

By M. H. Weinecke, B. P. Faulkner

This paper discusses the process for making lightweight aggregate, the waste materials that make good lightweight aggregate, the chemistry of making lightweight aggregate and the commercial prospects for making lightweight aggregate from wastes. Svedala Industries has been making lightweight aggregate (LWA) from waste materials for the last 10 years. Many claylike materials, such as coal fired boiler ash and washings from a granite quarry, can be used alone or with additional waste materials to produce commercially salable LWA.

Jan 1, 2003

By W. H. Su, S. S. Peng

Extensive investigation has been conducted to determine the causes of a series of roof falls occurring in an underground coal mine located in southern West Virginia. Underground observation, along with laboratory testings and finite element analyses, were conducted to search for possible mechanisms for the roof falls. Results of the investigation have led to a better understanding of the mechanisms involved in the roof falls. Necessary modifications of mine layout and roof support plan are proposed for improving safety and profitability at the mine.

Jan 1, 1987

By A. Guan, K. N. Han, J. J. Kellar, D. A. Boyles

Metal ions associated with effluent streams pose an increasing environmental problem for the mineral industry. Various techniques currently in use to combat this problem including bioremediation, chemical precipitation, and ion exchange are reviewed, and their relative advantages and disadvantages discussed. An alternative technique for metal ion removal, adsorption on surface modified alumina substrates is presented. Alumina surfaces were modified by adsorption of organofunctional silanes, and metal ion removal occurs by chelation of the ion by the adsorbed silane molecules. Experimental data is presented for the removal of cupric ions by this method and is compared to cupric ion removal by adsorption on alumina without prior surface modification.

Jan 1, 1994

By Brij M. Moudgil

Lack of understanding the major process parameters and inadequate scale-up factors have led to the belief that fundamental knowledge is not important for successful flotation plant operations. Flotation of simple and easy to process ores may not require a strong fundamental knowledge base for day to day operations. However, as low grade complex ores are mined and process control is integrated into flotation schemes, it is imperative for a plant operator to acquire a strong background in the basics of the flotation process at hand and/or have access to such a knowledge base at short notice. In order to meet the challenges of unexpected changes in the feed, reagent quality, water chemistry, physical, mechanical and hydrodynamic conditions, the flotation plant superintendent/chief metallurgist must have a strong background in the flotation fundamentals.

Jan 1, 1993

By Y. C. Kim, M. Preston, F. Martino

Because of the high cost of obtaining coal washability samples, it has been difficult in the past to obtain washability variograms. As a result, it could not be determined if the geostatistical prediction tool known as kriging can be applied to predict in situ coal washability characteristics. This paper presents the obtained variogram models for the Upper Freeport coal seam in western Pennsylvania. Variogram model parameters are presented for a total of 27 models. They are for four different variables: float- weight, ash, sulfur, and Btu, at seven different specific gravities: 1.275, 1.300, 1.325, 1.400, 1.600, 1.800, and 1.80,Sink. Based on the obtained variogram results, it can be con¬cluded that all attributes of coal washability show definite spatial correlation structures, and, consequently, geostatistics can be used to predict the in situ coal washability characteristics.

Jan 1, 1990

By Djamhur Sule, Husaini

Almost 90 % of phosphate in Indonesia is consumed for natural and manufactured fertilizers, while the rest is used in chemical industries. The consumption of phosphate always increases each year, while Indonesian phosphate production is almost constant at around 75,000 tons annually, except the production in 1988 was 165,000 tons. Due to the limited amount of domestic production, the imported phosphate is increasing each year. Phosphate trading in Indonesia is unique. Some of the domestic production is exported to Taiwan, while phosphate from USA, Morocco, Jordan and Nauru is imported. Indonesian phosphate includes guano phosphate, caving phosphate and small amount of marine phosphate sediment. Problems with Indonesian phosphate include: scattered deposits in difficult locations and a relatively small amount of reserves. Exploitation of phosphate deposits for domestic purpose has a good prospect, mainly because of the rapidly increasing phosphate demand as natural fertilizer or as a raw material for manufacturing fertilizer to support an agricultural sector.

Jan 1, 1993

By Mario E. Rossi

The concept of entropy is classical in thermodynamics and information theory. Its potential use as a measure of the ordering of a spatial system is discussed. Although entropy has been discussed previously in the framework of spatial statistics and for univariate distributions, a bivariate data-based estimator has not until now been defined. Different statistical distributions maximize entropy, depending on the univariate, bivariate, or n-variate constraints applied. For bivariate distributions, with a known mean and known covariance, it can be shown that the distribution that maximizes the entropy of the system is the bivariate gaussian. A nonparametric bivariate entropy estimator is introduced, derived directly from the experimental cumulative frequency distribution. Assuming that this experimental bivariate distribution is representative of the population distribution, then a measure of departure from gaussianity can be introduced as a relative entropy estimator. Practical applications for the entropy estimator are discussed, and an example developed.

Jan 1, 1992