Search Documents

By M. McPherson, P. Mousset-Jones, G. Danko

Calculation of the sensible heat transfer between the rock surface and the flowing air in an underground airway is still fraught with problems. There are only a few results available in the literature for the calculation of the convection in tunnels with naturally rough surfaces. Some of them are purely empirical, while others use a theoretical approach, based on the analogy between heat and momentum transfer, expressing the heat transfer coefficient as a function of the friction factor. A review and evaluation of these results are presented. The heat transfer equations obtained using the different assumptions, vary over a wide range, so that experimental results are needed to determine the formulae and constants applicable to mine airways. In situ measurements of the "physical" and "technical" heat transfer coefficient carried out in deep mines are described. The statistical distribution of the convective heat transfer coefficient on rough surfaces, as well as the regression between the Nusselt and Reynolds numbers in the turbulent flow region, are presented. Radiative heat transfer between the surface and the moist air flowing in a duct of relatively large hydraulic diameter has been taken into account during evaluation. The results will be a definite refinement of those calculations presently used in mine climate simulation models.

Jan 1, 1987

By C. Flores, R. Y. Wan, M. C. Fuerstenau, T. S. Jordan

Most oxidized manganiferous silver ores contain manganese associated with silver and are not amenable to conventional silver extraction methods, including direct standard cyanidation techniques. However, it is known that dissolution of the manganese might yield a suitable material from which silver can be recovered by conventional methods. In the segregation process, which involves heating the ore with a small quantity of salt and with a source of reducing agent to 680°C - 800°C, the silver is volatilized, migrates and is reduced to metallic silver particles. Conventional cyanide leaching is applied to the resulting calcine. Laboratory investigations have been conducted on a manganiferous silver ore analyzing 0.02 % Cu, 0.09 % Pb, 0.33 % Zn, 12.55 % Mn and 187 g/ton Ag to study the influence of roasting temperature and time, quantity of salt and quantity of coke on silver extraction by the application of segregation roasting followed by cyanidation. Cyanide leaching tests were carried out at room temperature on the segregated calcines produced by using an alkaline cyanide solution containing 2.0 lb/ton of NaCN at pH 11 for 72 hours. The results indicated that 97.8 % of silver extraction can be attained at 850°C, with 2.0 % salt, 1.0 % Coke and 30 minutes of roasting time.

Jan 1, 1993

By S. G. Hardcastle, Akbar Sheikh

In Canadian underground uranium mines, bacterial leaching is being increasingly applied to low-grade ore reserves. At Denison Mines Limited uranium operations, old stopes are used as leaching vessels; these contain a leaching muck pile brought down by drilling and blasting from the back which contained a low-grade reef. The bacteria used require atmospheric oxygen to oxidize the pyritic ore. A study was initiated to evaluate the ventilation, including oxygen supply, specifically, of flood leaching stopes during their rest period. The method of ventilation investigated was a single ended compressed air system which feeds airlines laid under the muckpile and carried through the inlet pressure bulkhead. The air delivery system was tested for post- blast integrity with a sulphur hexafluoride, SF6, tracer gas technique. This was injected into the intake compressed air line and collected at the stope's borehole exhaust in grab-sampling bags. The samples were analyzed with a laboratory gas chromatograph and results provided information on the stope's airflow, average residence time, overall clearance time, volume of the airpath and the airflow distribution. The borehole exhaust was monitored by anemometer and psychrometer and indicated that the psychrometric conditions in the stope were independent of the area's ambient climate. Evaluation of the exhaust's standard gaseous composition showed the oxygen consumption of the bacteria to be independent of the investigated flow range. Field derived results are compared with computer models, theoretical predictions and laboratory investigations.

Jan 1, 1987

By D. F. Symonds

INTRODUCTION Dense medium processes have been used to separate coal and ores for over a hundred years. In fact Sir Henry Bessemer first patented a process in 1858. In recent years, their importance relative to other gravity dependent processes has increased. This is particularly true in the coal industry where over 60% of all preparation plants operating in 1984 in North America (1) contained either dense medium vessel or cyclone circuits. In addition, the stringent product quality demands of the consumer, together with increases in mining costs, dictate that the cleaning circuits be both predictable and efficient. Dense medium systems are the most predictable and efficient of all gravity- dependent processes. The majority of the text of this chapter will be concerned with dense medium applications as they relate to the coal industry. However, the techniques and calculation procedures can be applied, in general, to all non-coal minerals (such as diamonds, marginal iron and lead-zinc ores and gravel) which take advantage of a difference in specific gravity between the saleable product and the reject. The object in dense medium cleaning is to produce a liquid whose effective specific gravity is between that of the concentrate and the reject. In which case the lighter product will float to the surface and the heavier product will sink to the bottom. Unfortunately, this simple process becomes complicated by the following practical necessities: (a) collecting and removing the float and sink products from the medium without disturbing the free settling effects; (b) maintaining and controlling the specific gravity of the medium; (c) separating and reclaiming the medium once the products have left the separating vessel; and (d) separating finer sized particles which take longer to fall through the dense, and often viscous, medium. As a result of the last issue (item d) two main types of dense medium separators have evolved: dense medium vessels and dense medium cyclones. Dense medium vessels are essentially large baths through which the dense medium flows at a relatively slow velocity. The lighter products float to the surface and are carried out of the vessel by the medium flow. The heavier products sink to the bottom of the vessel and are physically transported out either by means of a conveyor (usually a chain conveyor) or a rotating, lifting arrangement (Figure 1). They generally

Jan 1, 1986

By W. Jacobi, K. Eisfeld

The primary objective of dosimetric modelling for the inhalation of radon daughters is the evaluation of the dose distribution and of the mean dose to sensitive cells or target tissues in the respiratory tract which are assumed to be responsible for the initiation of lung cancer. The results of such dosimetric models are influencing the practice of radiation protection in a twofold manner: Firstly, they enable us to identify appropriate operational quantities for air monitoring and for the surveillance of individual exposures to radon daughters. Secondly, they can be used to derive secondary and operational limits for these radionuclides from the basic dose limits. The dose to target tissues in the lung from inhaled radon daughters depends on various physical and biological parameters: The unattached fraction of daughter atoms, the AMAD of the carrier aerosol for attached atoms, the geometry of the respiratory airways, the breathing conditions, the parameters for the retention and translocation of daughter atoms in the different lung regions, and the location of the target cells or target tissues, respectively. Therefore, dosimetric modelling for radon daughters has to include a sensitivity analysis showing the influence of these parameters. To meet these objectives we have recently described in a comprehensive report an improved dosimetric model for the inhalation of 222Rn, 22ORn and their short lived daughters (Jacobi and Eisfeld, 1980). In the following this model is shortly described and the main results are summarized. DOSIMETRIC MODEL [Model Structure]. For the geometry of the bronchial airways the model A of Weibel (1963) was used. Each bronchial generation i (i =0.1 .... 16) was considered as a separate compartment i, for which the following transfer pathways for radon daughter atoms were taken into account (see fig. 1): (1) the uptake by deposition (deposition probability wi); (2) the translocation by ciliary clearance (rate constant [A]i); (3) the transfer to blood by diffusion through the bronchial epithelium (rate constant [A]b). To distinguish between attached (Index a) and free (index f) daughter atoms each bronchial generation was divided in two subcompartments (i.a and if) with a transfer rate constant [a]s (ia- if) characterizing the desorption or dissolution rate of attached atoms in the mucus fluid. Thus for daughter atoms primarily deposited in attached form the transfer to blood is a twostep process with the rate constants [a]s and [A]b which were assumed to be independent of the generation number i. [Deposition]. The deposition probabilities wi in each bronchial generation were calculated on the basis of the laminar diffusion model of Gormley et al. (1949); however the deposition in the upper airways was corrected for turbulent air flow, taking into account the results of our deposition experiments (Martin et al., 1972). Figure 2 shows the resulting deposition probabilities per unit surface area of the bronchial generations for nose breathing at a rate of 20 1/min. The values for attached daughter atoms refer to an AMAD of 0.2 - 0.3 µm ([O]g =3) for the carrier aerosol; the deposition values for free atoms were derived with a diffusion coefficient of 0.05 cm2/s, assuming a prefiltration of 50% in the naseopharyngeal region.

Jan 1, 1981

By Richard A. Thomas, Liming Yuan, James H. Rowland III, DAVOOD BAHRAMI

To reduce the number of injuries resulting from fires on mobile, diesel-powered mine equipment, it is crucial to promptly suppress a fire once it is detected. The focus of this research was to determine the effectiveness of fire suppression agents. Large-scale tests were conducted using five different fire suppression systems based on: dry chemical, wet chemical, dual agent (dry and wet chemical), carbon dioxide, and water mist. Suppression nozzles were placed around the diesel engine where diesel fuel, engine motor oil, and hydraulic circulating oil spray fires were ignited. The results of this study can help mining companies and manufacturers by providing scientifically based data on the capabilities of the different fire suppression systems.

Feb 1, 2024

By Ken Pill, Jennifer Nyman, Liz Moran, Keaton Belli, Chelsea Bokman

The Moab Uranium Mill Tailings Remedial Action (UMTRA) Project Site (Site) is a former uranium-ore processing facility near Moab, Utah, where production ended in 1984. The United States Department of Energy Office of Environmental Management (DOE-EM) is responsible for remediating the site to meet 40 Code of Federal Regulations (CFR) 192 standards promulgated by the United States Environmental Protection Agency under the authority of the Nuclear Regulatory Commission (NRC). Tailings from the former mill were stored in an unlined impoundment (tailings pile), totaling 16 million tons of waste material. Surface cleanup has been ongoing since 2009 and consists of removal and transport of tailings via rail to an off-site disposal facility in Crescent Junction, Utah, with an estimated completion date around 2029. Gravity-driven migration of tailings fluids and recharge through the tailings pile and former on-site ore storage areas in the northeastern part of the site led to contamination of site soil and groundwater. The primary contaminant of concern is ammonia, which was present in fluids used in the milling process (DOE 2003). Uranium is a contaminant of potential concern. An interim groundwater remedy is currently in place that utilizes a system of extraction and injection wells to limit discharge of contaminated groundwater into the nearby Colorado River. Exceedance of surface water standards for ammonia are a principal concern due to potential endangered species fish habitat areas along the Colorado River adjacent to the Site. When necessary, surface water diversion is used to lower surface water ammonia concentrations when suitable habitats develop for endangered young-of-year fish. Once surface cleanup concludes and the tailings pile is removed, a formal groundwater remedy must be selected and documented in a Groundwater Compliance Action Plan (GCAP). Under Title 1 of the Uranium Mill Tailings Radiation Control Act, natural flushing (i.e., monitored natural attenuation), may be selected as the groundwater remedy if it can be demonstrated that the remedy will achieve groundwater standards within 100 years. The 40 CFR 192 groundwater standard for uranium is 44 micrograms per liter (μg/L), and the target groundwater concentration of ammonia based on adverse effects on local fish species is 3 milligrams per liter (mg/L). A collaboration with Geosyntec Consultants, Inc. (Geosyntec), the Moab UMTRA Project team, the DOE Office of Legacy Management, the DOE-EM, and the Network of National Laboratories for Environmental Management and Stewardship was held in 2022 with the goal to generate actionable recommendations to develop a GCAP for the Site. The primary recommendation was development of a groundwater fate and transport model to predict the remedial timeframe under various groundwater remedies. This paper presents the results of soil and groundwater sampling, geochemical modelling, and laboratory column and batch reactor testing that will be used to parameterize a numerical model for estimating the remedial timeframe under various scenarios, including natural flushing.

Feb 1, 2025

By David A. Hedderly-Smith

Sealaska Corporation, the Alaska Native Regional Corporation of Southeastern Alaska, was organized under the laws of the state of Alaska pursuant to the federal Alaska Native Claims Settlement Act of 1971. Large areas of Sealaska's 630,000-acre (250,000 hectare [ha]) fee subsurface holdings are underlain by carbonate, and while much of this material is assumed to be common variety limestone and lesser dolomite, at least two areas in the Silurian Heceta Limestone contain high-quality limestone at tidewater. This limestone has many potential commercial uses. On northern Prince of Wales Island, about 90 miles (144 km) north-northwest of Ketchikan, resource development at Sealaska's Calder deposit has established a reserve of 13 mil- lion short tons (st) (12 million metric tonnes [mt]) of carbon- ate rock containing an average of greater than 98 percent CaC03, approximately 0.5 percent MgO, less than 0.5 per- cent Si02, and approximately 0.15 percent Fe203, with insolubles averaging less than 0.5 percent and an average Hunter Brightness of 92.07 for the -150 mesh grind (with a bright- ness cutoff of 90). The deposit is open at depth and to the south. Ultimate reserves will likely be several times those currently established. In 1998, Sealaska began mining the Calder deposit, with about 100,000 st (90,000 mt) produced, and also completed a marine terminal one half-mile (800 m) from the deposit. The terminal can load ships up to 680 feet (200 m) in length at a rate of 2,000 st (1,800 mt) per hour. 0 m) in length at a rate of 2,000 st (1,800 mt) per hour. On Dall Island at Breezy Bay, about 60 miles (100 km) southwest of Ketchikan, Sealaska has identified a limestone reserve in excess of 150 million st (135 million mt) that (based on 18 surface samples distributed evenly over about a section of land) contains about 98 percent CaC03, and less than 0.5 percent MgO, 0.5 percent Si02, and 0.15 percent Fe203. Brightness of the Breezy Bay carbonate is considerably less than at Calder. Five samples of brighter material from Breezy Bay returned brightness analyses in the high 80s and low 90s; average brightness is probably below the mid- 80s. Sealaska has also identified a deposit containing more than 19 million st (17 million mt) of similar rock near View Cove, a few miles south of Breezy Bay.

Jan 1, 2001

By A. Chattopadhyay, J. Res

High-level electrical energy can be suitably converted to shock waves of stress that, in turn, may be used for disintegrating hard rocks. This development, known as the electrohydrodynamic method, is very safe and highly economical compared to other methods of rock breaking. This paper deals mainly with development of the equipment and some details of the experimental work carried out with different rocks and concrete block.

Jan 1, 1988

By R. H. Lambeth

Disposal of mine tailings in "waters of the United States" is presently prohibited even though case studies indicate that the practice may be environmentally viable. To simulate disposal in the natural environment, nine containers of tailings and sediment were instrumented and placed on the ocean floor near Juneau, AK as were ninety-six biosample containers. Pore water concentrations of five metals were determined, and biota populations were characterized for both materials. After 500 days of exposure there were no statistical macro scale differences between tailings and sediment biota populations or Cu, Pb, and Zn pore water concentrations. Tailings released slightly more Fe than sediment, but sediment released significantly more Mn than tailings. Disposal of mine tailings in marine waters may be environmentally safe.

Jan 1, 1998

By Chen Ziming, A. Burkert, A. L. Mular

A mechanism has been proposed for autogenous grinding that involves three distinct types of breakage: self impact breakage, media breakage and abrasion. Based on this analysis a mathematical model and an autogenous grinding simulator have been developed. Using pilot plant data fitted to the model, the simulator was tested and employed to examine both the scale-up problem and the effect of feed size distribution on performance.

Jan 1, 1995

By J. S. Murty

In this paper, a report is given of studies undertaken in a laboratory rod mill to obtain the optimum conditions for the desired particle size distribution for long-distance transportation of coal through slurry pipelines.

Jan 1, 1987

Mining at Hudson Bay Mining & Smelting's (H. B. M. & S.) Snow Lake Division is now in the mature stage of the mines lives. These base metal copper-zinc mines have been operating for over 30 years. Stopes had small pillars called "crown pillars", left between them. These pillars range up to 100 meters long by 40 meters wide and 15 meters thick. H. B. M. & S. has been successful in removing these pillars through the use of cable slings, electric scoops, longhole mining and diesel LHD equipment. The different shapes and sizes of these pillars has meant that many innovative techniques have been tried in order to find acceptable economic mining methods. An overview of the different methods will be outlined.

Jan 1, 1992

By John E. Urosek, Timonthy R. Watkins

Room and pillar mining accounts for approximately 73 percent of the active gobs used in the United States in 1993. The Mine Safety and Health Administration conducted field investigations on six different types of bleeder systems used to ventilate areas mined by room and pillar methods. This paper discusses investigations that were conducted at mines using four of these systems.

Jan 1, 1995

By Stavros A. Argyropoulos

The strides that have been made in recent years in applying Artificial Intelligence to pyrometallurgy, are reviewed. The computer reproduction of the way in which a human being reasons and calls on past experience and stored knowledge when faced with problem will be extremely helpful in pyrometallurgy. It is expected that Artificial Intelligence will be applied in all areas of human endeavor. Areas of pyrometallurgy that are most promising for expansion into A1 in the near future are presented.

Jan 1, 1990

By J. G. Wargo

In situ leaching of disseminate gold deposits has been studied from a theoretical perspective to outline the operating environment for the process. Rock permeability and the relationship of permeability to the site of gold particle deposition are key factors in predicting the efficiency of in situ leaching. Permeability measurements, however, have rarely been made during gold exploration, so that secondary geologic features of the deposit must be used. This paper examines some of the geologic characteristics of disseminated gold deposits and comments on the problems and possibilities of in situ leaching of gold.

Jan 1, 1987

By P. Petropoulakis

Computer technology in the mining activities of our company has been applied in the last decade. In this presentation the experience gained by applying this computer technology in mining spescific applications are reported. Attention is given to the problems phased out and to the methodology used for software selection, centralized and decentralized development, data processing personnel and end users training and support. The paper concludes with a report of the first results obtained and a look at the future developments of the system.

Jan 1, 1989

By Roman Pyrih, Jim V. Rouse

Because cyanide is a naturally-occurring chemical, geochemical and biogeochemical mechanisms exist to retard or attenuate the movement of cyanide and its compounds in the subsurface and to degrade such compounds into low-hazard reaction products. The attenuation capacity of subsurface earth materials can be measured, predicted, and enhanced by simple and inexpensive procedures. The paper describes methods of testing the geochemical and biogeochemical attenuation capacity of the subsurface and offers general suggestions for methods of enhancing such capacity. It also presents examples of data which documents such attenuation.

Jan 1, 1991

By S. Behl, S. Mathur

It was previously reported that dolomite samples from different locations showed varying flocculation behavior with poly(ethylene oxide) (PEO). In this study, a Florida dolomite sample was examined, and it was determined that palygorskite associated with dolomite was responsible for its flocculation with PEO. A detailed characterization of dolomite samples from different locations was made by electrokinetic, XRD and FT-IR analyses, and the relevance of these characteristics to flocculation with PEO is discussed.

Jan 1, 1996

By R. L. Urie, L. Burdzinski

Non-operational mine facilities are subject to placement on the EPA's National Priority List (Superfund). Once a mine site is undergoing investigation and/or remediation, MSHA regulations for health and safety may no longer be applicable. This paper addresses the changes in the applicable and relevant standards that apply to health and safety and public health related to site contaminants. The implementation of health and safety plans, and the development of public health risk assessments are described. Examples are presented from Superfund activities at the Eagle Mine, near Minturn, Colorado; the Anaconda Smelter near Mill Creek, Montana; California Gulch near Leadville, Colorado; and Bunker Hill, Idaho.

Jan 1, 1991