Search Documents

By Rudolf Greuer, Gerald Jalkanen, Huann-Sheng Chen

A short cut is presented where the average grade above a primary grade cutoff and its associated byproduct grade(s) are estimated by screening the primary and byproduct grades. For the primary variable, choose samples whose grades are above a cutoff of interest. Compute variograms for the subset of the primary variable. Then using this variogram, krige the blocks of interest only using the samples whose grades are above the cutoff. The next step is to screen byproduct grades by choosing byproduct samples whose associated primary grades are above the cutoff of interest. Next compute variograms for this subset of byproduct samples. Then using this variogram, krige the blocks of interest using byproduct sample grades whose associated primary sample grades are above the cutoff of interest. The results are the average grade above a primary cutoff for both the primary and the associated byproduct variables. Using two simulated primary and reference data sets a case study resulted in the screening krigings performing better than the indicator kriging approach in the first case study. A second case study had mixed results with the primary indicator approach performing better than the primary screened approach. The byproduct screened approach performed better than the byproduct indicator approach.

Jan 1, 2002

By P Moser

Within the EU-research project "Blasting Control", jointly operated with partners from France, Italy and Greece, between 1992 and 1995, the Department of Mining Engineering of the Montanuniversity Leoben, Austria took over the task to develop a diagnosis system applicable in underground drifting, in order to identify possible reasons for blast failures or poor blast performance. For that purpose 120 m of 12 m2 test galleries were excavated at two different mine sites. For every blast performed the collar and bottom position of every hole drilled, the charged hole length and the drift and face profile of the round blasted were monitored. These 'geometrical" data were put directly from the measuring devices into SURPAC, the mine planning software chosen for data analysis. Based on the data computed, 3D plots comparing actual and planned data were made visible on the screen or as hard copies. Experience from the introduction of this system into a mining operation showed, that the system developed contributes to an improved understanding of the reasons for blast failures and forms the basis for an improved blast design. The soft- ware package SURPAC was also used to train the miners directly at the mine site in order to improve the quality of their work.

Jan 1, 1996

By Bruce D. McCellan

INTRODUCTION The gathering arm loader was patented by Joseph Joy in 1916. This unique machine motion became the standard of the industry and is used on underground loaders and continuous miners throughout the world. Figs. 1 and 2 show two types of gathering arm loaders. The gathering arm loader is a crawler-mounted ma¬chine primarily used for loading coal in a conventional mining system. Other uses also have been found for this machine in noncoal mines and other industries. MECHANICAL ASSEMBLIES The front or loading end of the machine, commonly called the head, consists of a tapered structural frame, hinged at the rear to the chassis and riding the ground at the front. Two bevel-gear cases are mounted in the head. They are connected by a timing shaft, which also acts as a conveyor drive shaft on most models. An eccentric disk attached to each gear case drives the gathering arms. The rear of the arms are attached to a swivel assembly. The motion derived from this arrange¬ment gathers loose material from the ground directly in front of the machine and loads it into the conveyor. Power for this drive is provided by two electric motors mounted under the gathering head. A speed reducer attached to each motor provides a gathering arm speed of approximately 5.2 rad/s (50 rpm). A torque limiting clutch is provided on each reducer to guard the system against sudden impact loading and continual overloading of the motors. The conveyor consists of an open box section through which a universal-type chain carries the ma¬terial to the rear of the machine, where it is discharged into the haulage vehicle. The chain is driven by a sprocket located on the timing shaft between the two gathering-head bevel-gear cases. On some large loader designs, primarily for noncoal applications, the chain is driven by a separate gear motor at the discharge end of the conveyor. However, the system driven by the timing shaft is used most widely. The conveyor frame is hinged just to the rear of the gathering head. It can be raised or lowered by hydraulic cylinders to the desired discharge height. The conveyor frame also is designed to pivot 0.79 rad (45°) either side of the center, just to the rear of the chassis. This feature increases the maneuverability of the ma¬chine and makes it possible to discharge material into the haulage system when in tight quarters such as when turning a crosscut. This function also is controlled by a hydraulic cylinder. The chassis of the loader consists of two crawler frames and cross members, holding the frames in position. The frames are either welded or cast as¬semblies. Replaceable wear runners are provided on the frames to take the wear generated by the crawler chain. An adjustable take-up idler keeps the crawler chain in proper adjustment for maximum life. The drive system for the crawler chains varies with the manufacturer, but it generally is one of two basic designs. One system provides a traction motor for each side of the machine, coupled to a speed reducer. A spur and bevel-gear train transfers power to the sprocket, which drives the crawler chain. Directional control is achieved by disk-type clutches. The other system also uses a motor for each crawler, coupled to a speed reducer. A roller chain drives the sprocket, which in

Jan 1, 1982

By P. K. Ackerman, F. F. Aplan, G. H. Harris, R. R. Klimpel

Fourteen reagents that are potentially capable of chelating with a metal ion on the surface of the major copper sulfide minerals and pyrite were evaluated for their effectiveness in floating these sulfides. The reagents studied fall into the classes of mercaptobenzole mutations, thiouronium, thionocarbamates, thiourea, imidazole mutations, oximes, hydroxyquinoline and xanthogen formate. The best overall copper sulfide collector was an imidazoline (1-Hydoxyethyl - 2-Heptadecenyl), but it also proved to be an excellent collector for pyrite. Its potency as a pyrite collector can be reduced by structural alteration, but at some loss in its collecting power for the copper sulfides. The effectiveness of many of these potential collectors can be changed by minor alterations to the collector molecule and, to a lesser extent, by pH adjustment. The general order of mineral floatability with these reagents is chalcopyrite = chalcocite > covellite =bornite >> pyrite. The flotation of malachite is generally similar to that of the copper sulfides, indicating the special effectiveness of copper in the crystal lattice for collector attachment.

Jan 1, 2000

By S. N. Groudev

A process for the combined chemico-biological removal of iron present as oxide minerals in different mineral raw materials (quartz sands, kaolins, clays, etc.) was developed. In the process, mineral raw materials are leached at about 90 °C with lixiviant containing microbially produced oxalic and hydrochloric acids. The leaching is carried out in mechanically stirred acid-resistant reactors for periods of from 1 to 6 hours, depending on the iron content and the forms of iron in the raw materials being leached. The iron contents of some sands treated by this method were lowered from levels that were in the range of 0.035% to 0.088% Fe2O3 to less than 0.012% Fe2O3, making them suitable for the preparation of high-quality glass. The iron contents of different kaolins were lowered from levels that were in the range of 0.65% to 1.49% Fe2O3 to levels in the range of 0.44% to 0.75% Fe2O3. As a result, the whiteness was increased from values of 55% to 87% to values of 86% to 92%. The iron content of clay was lowered from 6.25% Fe2O3 to 1.85% Fe2O3, and this increased the “fireproofness" of the clay from 1,670°C to 1,750°C. A similar process was used for the leaching of aluminum from aluminosilicates, mainly clays and kaolins. However, in this case, the microbial fermentation fluid containing citric acid was acidified by means of sulfuric or hydrochloric acid or by means of different mixtures of mineral acids. For enhancing aluminum solubilization, the aluminosilicates were heated before leaching at 600° to 650°C for 1 to 2 hours. Over 90% of the aluminum present in different clays and kaolins were leached within 3 to 6 hours. "Silicate " bacteria related to the species Bacillus circulans were used to leach silicon from low-grade bauxite ores containing aluminosilicates as impurities. The bacterial action was connected with the degradation of the mineral structures (by means of microbial metabolites such as organic acids and exopolysaccharides), as well as with the selective separation of the rich-in-aluminum fine fractions, which were retained by the mucilaginous capsules of the bacteria. The solid residues after treatment were characterized by higher values of alumina and silicon module (A1203: SiO2 ratio), and they were suitable for processing by means of the Bayer process for recovering aluminum. The bending strength and other ceramic properties of kaolins were improved by contact with well-developed cultures of "silicate" bacteria. The improvement was caused mainly by bacterial metabolites (exopolysaccharides) that acted as resins during drying.

Jan 1, 2000

By Michael E. Mcllwain, Lee O. Nelson, Robert D. Rogers, James H. Wolfram

Examination of the economics and environmental consequences associated with phosphate fertilizer production documents the necessity for development of innovative production technologies. Evidence of phosphate ore's susceptibility to microbial alteration indicates that it will be an ideal candidate for industrial-scale bioseparation. There are at least two applications for the biosolu- bilization technology: (1) an industrial-scale bio- process similar to the presently used wet acid process and (2) production of small prills (bio- bead) containing unprocessed rock phosphate and the biological ingredients necessary to promote phosphate solubilization. At the present stage of development, the biobead technology is the preferred application. It is an energy-efficient "green" technology that will dramatically reduce the amount of solid waste and air emissions produced by the phosphate industry.

Jan 1, 1999

By S. Makni, C. Bazin, D. Hodouin

This paper reviews approaches for the real-time estimation of mass flow rates and assays using data from on-stream analyzers and flowmeters in a flotation circuit. Results obtained using one algorithm operating on-line with an industrial flotation circuit are presented.

Jan 1, 1998

By R. J. Sweigard, R. V. Ramani

The effects of postmining land use planning are addressed in this paper. These effects may include savings in reclamation costs and increased value of reclaimed land. However, this may result in greater planning costs and possible delays in production. Therefore, an economic analysis was undertaken in an effort to determine the importance of each potential result and to quantify the overall economic impact of postmining land use planning. A discounted cash flow analysis was performed using a surface mine cost model to analyze the sensitivity of selling price to changes in various postmining land use planning parameters. As a result of this analysis, it was determined that the profitability of a project is most sensitive to delays in production, particularly if the delay occurs after major investments have been made. Many methods have been proposed for evaluating postmining land use alternatives (Sweigard and Ramani, 1981). Both quantitative methods, such as benefit-cost analysis (Brock and Brooks, 1968), and nonquantitative methods have been proposed. The application of one specific analytical method is pursued in this paper.

Jan 1, 1988

By J. V. Calara, J. D. Miller

The sign of the surface potential for complex non-reactive ionic solids cannot be predicted solely from consideration of the hydration energy of gaseous ions which constitute the ionic lattice. Accurate analysis of these systems must involve the hydration energy of surface ions, which requires knowledge of the crystal structure, the identification of cleavage planes, and the calculation of binding energies of surface ions. Surface binding energies for ionic solids can be deter- mined if the Surface Madelung Constant is known. A computational technique was developed for the calculation of Madelung Constants for infinite lattices which gives excellent agreement with the values calculated by other more complicated methods reported in the literature. Extension of this technique permits the calculation of Surface Madelung Constants and binding energies of surface ions, ?Us, for semi-infinite solids. The hydration free energy of gaseous Ions, ?Fh, together with the calculated binding energy of surface ions, ?Us, allows calculation of the hydration energy of surface ions, ?Gh, as for the case of the ionic solid, MX:

Jan 1, 1976

The objective of this study is to classify ore and waste in a selected mine. The support vector machine, was used for the classification purpose, is applied to a zinc ore body in a skarn deposit located in the central region of the Peruvian Andes. The input parameters used for the model are spatial coordinates and the lithological information of the ore body. The input data was divided into training and testing data sets and the performance of the model was tested using the testing data set. The results show that more than 76% of the data could be properly classified by this method. The ore waste maps of the deposit was then developed using SVM model. From the result it was observed that a comparatively very few number of cells classified as ore. The ore is concentrated in small lodes at the middle of the volume of study, and not uniformly distributed throughout the study area. The lithological map of the deposit was also constructed as it was used as an input parameter for the SVM model. The indicator kriging was used for generation of lithological map of the ore body. Key word: Ore waste classification, Support vector machine, Indicator kriging, Confusion matrix.

Jan 1, 2008

By Karel SPIRKO

The one-dimensional mathematical model of unsteady-state heat conduct ion through multilayer (wall and floor of airway consist of several layers of material and rock) and two-surface (dry and wet surfaces) airway wall and airway floor with convective heat and moisture transfer between their surfaces and mine air with time dependent changes of temperature and humidity has been developed on the basis of introduction of acceptable simplifications of description of heat and moisture transfer between rock mass and mine air. The analytical solutions for calculation of the surface temperature of any type of surface of airway wall/floor and for calculation of water vapour pressure near the wet surfaces at given time are obtained by means of the model presented. These solutions are illustrated for the case of general harmonic course of air temperature and humidity. Balance of heat and moisture transfer between surfaces of airway wall and floor and mine air is solved by an iterative method in the partial sections of airway. The temperature and the humidity of mine air on the outlet of each partial section of airway at given time are its resolutions and they are the input data for following partial section. By this way it is possible to solve complicated dynamic changes of mine air temperature and humidity in an air way system by relatively simple mathematical apparat.

Jan 1, 1991

By T. A. P. Sankar, S. Gundiah, Pradip, R. A. Kulkarni

Two modified polyacrylamide flocculants, namely polyacrylamide with glycolic acid functionality (PAMG), and a copolymer of acrylamide with N-acryloyl-[T]- aminobutyric acid (HPVP), were synthesized, characterised and evaluated for selective separation in apatite/quartz and apatite/dolomite/calcite systems, respectively. PAMG flocculant was found selective in the separation of tricalcium phosphate (TCP) from its mixtures with quartz at acidic to neutral pH range. The selectivity deteriorated at alkaline pH. In contrast, polyacrylic acid (PAA) flocculant was found most effective only in the alkaline pH range. HPVP flocculant (even though flocculating all three minerals namely apatite, dolomite and calcite) was observed to be quite selective for the separation of calcite from apatite-dolomite minerals in single mineral tests in the presence of sodium hexametaphosphate dispersant at neutral pH. There was, however, no selectivity observed during tests on synthetic mixtures. This loss in selectivity is attributed to the phenomenon of hetero-flocculation, as reported earlier, for separation in an apatite-dolomite system with polyethylene oxide.

Jan 1, 1993

By J de Cuyper, G. Rinelli, A. M. Marabini, V. Alesse, W. Freyberger

Salicylaldehyde, a chelating agent for tin, has been found to function as a collector for the flotation of cassiterite. Infrared and nuclear magnetic resonance studies clearly show that salicylaldehyde can form a chelate compound in bulk and at the surface. Results are also given for the flotation of a tin ore with this reagent.

Jan 1, 1976

By J. H. Mackey

"Where can I obtain a reclamation bond today?" "Who is writing your bonds?" These questions are common and heard frequently. The fact that the Society of Mining Engineers has determined that two of the five environmental topics reviewed at the 1989 Annual Meeting relate to reclamation bonding indicates to me that those who are involved in the coal industry, no matter what capacity, remain very cognizant of the reclamation bonding dilemma.

Jan 1, 1989

By J. R. Mattern

The engineering geology of the Rio Tinto Borax Boron Mine creates challenges in providing practical slope design recommendations to mine planning engineers. Low strength sedimentary units interbedded with very low strength lakebed clays surround the orebody. Faulting has offset and juxtaposed these units into variably adverse orientations, while groundwater is compartmentalized both vertically and horizontally within fault blocks. A collective program of geologic data collection, geomechanical strength testing, geologic modeling, slope depressurization, confirmation of underground stope locations, and documentation of slope behavior provides vital information for design investigations and sensitivities. Analysis results lead to risk assessments and operational procedures that add value to the business by optimizing slope configurations and minimizing risk.

Jan 1, 2004

By Helen Leung, Colin R. Phillips

The performance of personal alpha dosimeters in mixed radon daughter and thoron daughter atmospheres in Ontario uranium mines is described together with monitoring developments which enable the radon daughter working level to be determined separately. The theoretical bases for continuous and integrated working level measurements based on individual and gross counts are presented in terms of the weighting factor for combining the thoron daughter working level with the radon daughter working level, and in terms of the in-growth time of the air. Implications for the determination of working level in the presence of thoron daughters are discussed.

Jan 1, 1981

By Bonn J. Macy, David A. Gulley, William A. Vogely

INTRODUCTION Some of the most famous and graphic environmental incidents have arisen from mineral extraction, including oil spills, the Reserve Mining asbestos tailings case, Kaiparowitts surface mining and coal combustion, and other environmental causes celebre. The remote location of much of the mining industry to some extent reduces the human health hazards from pollution, but often times the pristine locale in which mining is conducted provides a sharp contrast to the impacting industry. This prompts questions as to what the research literature says about the true costs and benefits of environmental compliance. We survey the state of this knowledge. Where possible, we discuss studies focused on mining and related industries, such as primary metals production. In many cases, how- ever, the studies pertain to the economy as a whole. For present purposes, the mining industry is defined as companies engaged in the production and refinement of minerals, including metals, fuels, and nonmetallics (e.g., phosphate, sand and gravel). There are several stages in mining, with environmental effects occuring at every stage. The exploration stage comprises the period from initial prospecting to the point where the deposit has been located and delineated in sufficient detail to permit development decisions to be made. Geophysical and geochemical surveys, diamond drilling programs, and exploratory stripping and excavation are activities that may be employed during this stage. Some forms of prospecting are relatively benign, al- though even airborne surveys and motor vehicles generate noise pollution. Roads and the passage of vehicles and equipment affect land surfaces and vegetation, and attract heavier backcountry use. Clearings, stream crossings, and borrow pits can lead to increased erosion and sedimentation of streams. Geological survey grids disrupt vegetation and appearance. Moreover, prospecting can involve the excavation and stripping of overburden, resulting in soil and vegetation disruption as well as in- creased sedimentation of streams and lakes. The effects of exploration are often temporary, and frequently less severe than for other activities. Nevertheless, exploration-related impacts vary with the intensity and type of exploration effort, and can be significant. During the development stage of mining, shafts are sunk, pits excavated, buildings erected, and transportation facilities established. Dust, noise, and other socioeconomic and environmental impacts are generated by the relatively large and sudden influx of people, equipment, and activity. Surface disturbance and solid waste are generated by development, and liquid wastes form when mines are dewatered. The extraction phase is associated with a variety of environmental impacts. These impacts may differ for surface and underground mines. In surface mining, surface disturbance is obviously a major consequence. Piles of overburden and waste accumulation mar land surfaces. Wind and water erosion tend to spread the dis-

Jan 1, 1985

By C. H. Bucknam

A suite of ore and waste rock materials was selected for the interlaboratory testing of combustion-infrared ("Leco") methods used to estimate carbonate and sulfide minerals present in test materials. The objective of the study is to develop ASTM standard methods to be used for metallurgical characterization of ore, acid drainage prediction for ore and waste during ore body evaluation, and for ore and waste control during the active mining of ore deposits. The results may be interpreted for classification of the materials according to their carbonate-sulfide or acid-base characteristics based on net carbonate value (NCV). The test materials were processed by x-ray diffraction and x-ray fluorescence (XRD-XRF) at Newmont Metallurgical Services (NMS) to obtain a semiquantitative mineralogical composition. Results of the interlaboratory testing for total carbon-sulfur, pyrolysis loss carbon-sulfur and hydrochloric acid residual carbon¬sulfur are compared with the mineralogical composition to aid in interpretation of the NCV classifications of the samples.

Jan 1, 2002

By P. C. Schutte, A. J. Kielblock

INTRODUCTION Certain activities, such as emergency work and rescue operations, often have to be undertaken in environments where heat loads often exceed limits prescribed for routine work. This is particularly relevant to the South African mining industry where heat stress-induced fatalities are not uncommon during rescue operations. In this regard an excessively hot environment is defined as one where either the dry-bulb temperature exceeds 37,0°C or the wet-bulb temperature exceeds 32,5"C, and it is therefore not surprising that heat stroke mortality escalates rapidly when these limits are exceeded. A review of both local and international standards indicated that the available information on safe exposure times under abnormal heat stress conditions is very limited. Where available, such standards are aimed at the general population, including both sexes, irrespective of age and also the least heat tolerant worker, and not at a medically-screened, all-male population free of grossly heat intolerant individuals, as is the case in the South African mining industry. It is suggested that available norms and limits are too conservative for local application and, therefore, unrealistic. In view of the definite need to protect workers when exposed to abnormally high environmental temperatures, the present study was undertaken to establish a scientifically derived data base. applicable to local conditions, to determine safe exposure times: Any exposure limit, especially in an emergency situation, should be easy to administer, valid and reliable. These aspects, there- fore, form an integral part of this paper. FORMULATION OF HEAT STRESS LIMITS The formulation of heat stress limits was based on the criterion that a heat exposed individual should experience a negligible risk of developing dangerously elevated body temperatures. In order to provide a database for risk assessment, certain physiological responses of heat tolerant men were determined at various combinations of thermal conditions and work rate in a climatic chamber. These physiological responses were analysed statistically in order to predict safe survival and tolerance times as a function of thermal conditions and work rate. EXPERIMENTAL DESIGN A total of 202 randomly selected, medically fit mine workers volunteered for the study on the basis of informed consent. These men were considered to be inherently heat tolerant in as far as they had successfully completed a heat tolerance test (Anon., 1991) or the standard climatic room acclimatisation procedure used on many South African gold mines (Anon., 1989). The subjects were allocated randomly to 14 experimental groups and each group was exposed in a climatic room to one of

Jan 1, 1997

By Kal V. S. Sastry

Modeling and simulation are two major tools available to a mineral process engineer for a consistent and systematic process analysis. The application of these tools to the analysis of specific mineral processing unit operations is well documented in the literature; nevertheless, they are used only to a limited extent in the industry. This is because the fundamental principles of modeling and simulation in the context of mineral processing context are not available. This paper represents the first in a series of papers planned to meet this need. General principles of process modeling and a unified mineral process model development methodology are presented. A simple example of model development using the flotation unit operation is given. A discussion of the practical significance, challenges and opportunities associated with mineral process modeling is included.

Jan 1, 1990