Search Documents

By Todd A. Duex

The Richmond Hill Mine has recently completed a reclamation plan to mitigate Acid Rock Drainage (ARD) which was identified at the toe of the former waste rock pile in 1992. Reclamation activities began in 1994 with the removal of ARD material from the waste rock pile and placement of this material in the former pit. This material was then isolated from the near surface environment by a low permeability capping system designed to minimize water and oxygen flow into the material. The capping system consists of, from bottom to top, six inches of limestone, 18 inches of low permeability clay liner, 4 and one-half feet of thermal barrier/drain layer, and six inches of topsoil. This capping system was completed in 1995. An extensive program is in place to monitor the effectiveness of the reclamation plan, and includes measurements on moisture content movement, temperature, oxygen content, and groundwater impacts. Monitoring has been ongoing since the completion of reclamation. This monitoring plan is demonstrating the success in isolating the material from the near surface environment and minimizing the impacts to the surrounding environment.

Jan 1, 2000

By Mike Irish, Deb Mukhapodhyay

It has been demonstrated by Arrowhead Industrial Water that a proprietary reverse osmosis technology can be used efficiently, effectively, and economically to reduce the levels of cyanide species, heavy metals, and other ions as shown in Figure 1 to allow safe discharge of a permeate solution to the environment. A simultaneous benefit of this process was the cost savings of reduction in quantities of cyanide requiring destruction by hydrogen peroxide and recovery of a concentrated gold and silver value in the concentrate solution.

Jan 1, 1992

By M. H. H. Mahmoud, T. A. El-Barbary, E. A. Abdel Aal, I. A. Ibrahim, A. K. Ismail

Fertilizer-grade phosphoric acid with a P2O5 concentration of 50% should contain less than 1.5% Fe2O3, otherwise, the P2O5 water solubility of the fertilizers prepared from high-iron acids will be low. High-iron Egyptian phosphate concentrates fromAbu-Tartur and Sebaiya- West were leached with sulfuric acid and recycled phosphoric acid to produce 50%-P2O5 phosphoric acids containing 4.0% and 2.7% Fe2O3, respectively. The high iron contents were reduced to the industrially accepted limit of 1.5% Fe2O3 by precipitation with potassium sulfate. The factors affecting the effi¬ciency of the precipitation process, e.g., temperature, time and K2O/Fe2O3 ratio, were systematically studied, and the optimum conditions were achieved. The clarification of the prepared phosphoric acid from iron-containing sludges was also investigated by varying the time and temperature. The utilization of the separated sludges as fertilizer and recovery of P205 by pulping in water were also evaluated.

Jan 1, 2000

By Serkan Saydam, Ercument Yalcin

This paper presents the results of Caldagi Nickel-Cobalt Ore Deposit's, located in Turkey, reserve and ultimate pit limit design analysis. Reserve analysis of any deposit requires two steps. First one is to constitute of block model of the deposit and second step is to generate ultimate pit limit. The block model of the Caldagi ore deposit has been created by means of geostatistics. The reserves of nickel and cobalt in this block model are defined as resource, approximately 12 million tons of nickel and 1 million tons of cobalt with average grades of 0.9% Ni and 0.03% Co, respectively. Ultimate pit limit analysis has been performed by considering economic, technical and legal factors. In this paper, the ultimate pit limits are generated by Lerchs & Grossmann (L&G) algorithm. As a consequence of ultimate pit limit design, total amount of tonnage to be excavated is 1.4 billions of tons, 700 million of which contains ore and 747 million of which is the tonnage of waste.

Jan 1, 2002

By K. Morsy, S. S. Peng

This paper deals with the causes and mechanisms of massive pillar failure in a room-and-pillar mine that employed nine-entry panel system using supersection technique under a cover ranging from 91 to 168 m (300 to 550 ft). Chain pillar squeeze and large roof-to-floor convergence were first observed at the belt transfer point on the very inby side of the main entries. It propagated outby quickly and within 24 hours it had covered an area approximately 1,250 m long by 762 m wide (4,100 x 2,500 ft). The failure was caught and stopped by a solid barrier pillar. Using computer modeling, the study indicated that the massive failure was initiated due to a combination of undersized chain pillars in some panels and weak immediate floor. Also, the study shows that the massive pillar failure expanded to a large area because of no barrier pillars between some panels and between mains and panels. Based on the computer modeling, alternative mine plans have been proposed to avoid such problems.

Jan 1, 2000

By L. A. Puchkov, Mesentsev. V. K., I. O. Temkin

The problem of increasing underground mine ventilation efficiency is still of top priority. The complication of geological conditions with the depth of underground mining processes and reinforcement of requirements to technological and ecological safety are extorting the necessity of solving this complex problem with using of new information technologies. There exist different approaches to the ventilation problem. One of them, which the authors adhere to, is based on the concept of monitoring (under special mining and geological conditions-automatic control) of mining atmosphere and operative re-distribution of underground mining air among consumer , in accordance with the criterion of optimality [ 1.3 1. ] The set of tasks which should be decided in the frame of con- crete ventilation system depends on the peculiarities of deposit, technological schemes and so on. Nevertheless, some ventilation tasks such as: defining of ventilation network parameters; finding of dependence between these parametrs; operative redistribution of air streems, could be interpreted as universal ones. Main aspects of practical solving of different ventilation problems and their classification were investigated and considered in detail before [I ,2 ]. Some years ago we have began our investigations to develope quite simple and effective methods for decision of ventilation tasks on the base of neural network technology. It is well known that ventilation net, formed by various mine workings, is the main component of underground mining ventilation system. In general, network air distribution may be described by some functional F(Q,R,H), where Q- is a vector of air consumptions; H- is a vector of depressions; R- is a vector of airdynamic resistences. (Q,R,H) - are the informative entities , characterising every branch of the net. There exist some fundamental tasks which should be decided during the process of control of mining ventilation: calculating of natural air distribution Q = Q,{R, H,}, or Q = Q2(R, Q?}, where H, - is the maximal depression of the ventilation net, Q, - is the air consumption in the ventilation shaft; identifying of airdynamic resistance for some branches on the base either of air-depression removal or operative monitoring: [ ]

Jan 1, 1996

By J. W. Leonard

Breakage, handling and treatment techniques that result in the placement of greater quantities of coal in fixed volume haulage units such as ships, railroad cars, trucks, mine cars, shuttle cars and scoops can do much to increase productivity by improving bulk density to reduce delivered cost, surprisingly enough, only in steel industry by-product coking has this subject been investigated and applied to practice, where as much as 20% or more productivity has been achieved. Research at UK Mining using popular coal mine loading cycle simulators shows that for typical Central Appalachian mining conditions a 10 to 20 percent gain in bulk density can produce a 15 to 30 percent increase in the loading cycle time of fixed volume shuttle-car/scoop based mining systems.

Jan 1, 1989

By Thomas de Lange

Extensive test work performed on the Coalscan 3500 ash analyzer at the Grootegeluk Coal Mine has led to the successful implementation of on-line ash monitoring to control the quality of coking coal and power station coal. Test work results are given and the advantages of on-line bias compensation discussed. Some details of the quality control systems subsequently implemented are also highlighted. Finally, the economic benefit of on-line ash monitoring based on the Mayer curve is demonstrated.

Jan 1, 1992

By Tim Cleary, Steve Skelhorn

The 9th Line / 16th Ave tunnels are part of a $700 million expansion of the York Durham Sewage System, north of Toronto. The 15 km of tunnels presented many challenges, including glacial and postglacial deposits, at depths up to 55 m. Due to high hydrostatic heads, the Owner specified EPB tunnelling, however, an alternate was proposed utilising rib and lagging tunnels, combined with a de-watering scheme. State of the art technology was utilised with a new Lovat TBM, incorporating PLC control, soft start water-cooled motors and a head designed to tackle the mixed ground expected. The 9th Line tunnels were completed in 2002. Subsequently the second section of tunnel along 16th Avenue has been awarded to the Joint Venture. This paper presents a case history of the soft ground tunnelling, including design elements, tunnel systems and TBM operations.

Jan 1, 2003

By Ian Sheppard, John J. Chen

This paper describes the development of the underground mining methods employed for narrow silver-lead-zinc orebodies at the Isa Lead Mine. Cut-and-fill methods were the chief underground mining methods for the narrow orebodies at the mine over 35 years ago. Benching methods were introduced approximately two decades later, and quickly replacing the cut-and-fill methods. The cut-and-fill methods and the benching methods are briefly reviewed in the paper. The benching methods and technologies have been continually evolving and one of the recent achievements is a multi-lift benching method. The multi-lift benching method is described in detail.

Jan 1, 2001

By Legett Garrett

Texas Utilities Generating Company (TUGCo) surface mines lignite for use as a boiler fuel at mine mouth generation stations. Currently, the annual lignite production requirement of approximately 28 million tons necessitates mining across approximately 1,600 surface acres each year. The mining operations, located in Freestone, Panola, Titus, and Hopkins counties, Texas, have drastically disturbed some 13,000 surface acres to depths of up to 110 feet since initial startup in 1971. The TUGCo mining philosophy, a commitment made prior to initiation of mining operations and prior to any mining regulations, includes a return of mined-out land to private ownership in the most useful state possible. In the areas of TUGCo operations, the local economies are based upon agricultural production. Historic land use surveys have typically shown a trend from row crop production to pastureland for cattle production. During the 1960?s, the percentage of acreage devoted to row crop production approached zero with respect to the total acreage devoted to agriculture. TUGCo reclamation operations have therefore emphasized restoration of land to a state that is favorable to cattle production

Jan 1, 1982

By S. G. Malghan, W. H. Moyer

In reference to the section "Excess pyrite," the author discusses difficulties in separating chalcopyrite from pyrite. A technique does exist, and has been used commercially, for the flotation, separation, and recovery, if desired, of both chalcopyrite and pyrite. The method was described in Mining Engineering, March 1966, "An Improved Flotation Method for Cornwall Sulfides." While it was not used on a porphyry copper ore, it was used on a chalcopyrite- pyrite-containing ore and might well have application. Both sulfides, chalcopyrite and pyrite, were floated simultaneously using xanthate as a collector and MIBC frother to produce a cleaned sulfide product. This concentrate was then thickened and conditioned at high solids with aeration and lime to a pH above 12.0 for a period of 1.5 to 2 hr. A supplemental suppressant, such as cyanide, could be used if necessary to sharpen the subsequent separation; however, it was not required at Cornwall. The conditioned sulfides were floated with two stages of cleaning to produce a high- grade chalcopyrite froth product and a pyrite sink product barren in copper. The separation at Cornwall gave a 28.6% Cu grade chalcopyrite product and a pyrite analyzing 0.06% Cu. A desliming step on the raw ore initially used at Cornwall for a period of time was later discontinued. Advantages to be found in using a strong sulfide collector, such as a xanthate, is the rapid flotation it induces and, generally, an ability to float at a coarser grind. A following regrind circuit could be used to give maximum liberation and produce a clean sulfide concentration. The "differential" separation is concerned primarily with grade and with assuring a barren pyrite for maximum recovery.

Jan 1, 1987

By E. M. Hill, D. E. Walsh, J. T. Hollow, H. K. Lin

Fairbanks Gold Mining, Inc. (FGMI) began blending and processing True North ore at their Fort Knox mill on April 12, 2001.Gold extraction subsequently dropped from 88% to 71% during the last week of April 2001. 25% of the gold values remaining in the leach tailings were gravity recoverable free gold. Significant quantities of stibnite and arsenopyrite were also identified in the tailings. In laboratory bottle roll tests, the gold extraction from a composite of leach circuit feed collected during the same period was 72.6%, when leached at an average NaCN concentration of 0.16 g/kg. The extraction increased to 82.4% and 91.7% with 0.5 g/kg NaCN, and 0.5g/kg NaCN plus 0.075 g/kg Pb(NO3)2, respectively. A passivating layer surrounding liberated gold particles and resulting from sulfide mineral dissolution, likely contributes to reduced gold recovery, which can be substantially increased by the addition of lead nitrate. Lead species remain in the solid residues after leaching and were not mobilized using Meteoric Water Mobility Procedure.

Jan 1, 2003

By Frank E. Dalton

The Metropolitan Sanitary District of Greater Chicago (MSDGC) serves an area of approximately 860 square miles and collects and processes used water from the city of Chicago and 116 surrounding communities. As a public agency, the MSDGC -Serves a population equivalent to 10 million people which is composed of 5.5 million people and an industrial wasteload equivalent to an additional 4-1/2 million people. -Provides 400 miles of intercepting sewers and tunnels ranging in diameter from 12 inches to 24 feet. -Operates 71 miles of navigable waterways and channels conncecting the Atlantic Ocean and the Great Lakes with the Gulf of Mexico and 6,000 miles of inland waterways. -Maintains the largest water reclamation plant in the world. -Processes 1,380,000,000 of used water daily and removes approximately 1,000 dry tons of organic solids each day. -Has spent approximately 700 million dollars in capital improvements to date, and will require expenditures in excess of 3 billion dollars (including over one-half billion dollars in tunnels) to meet existing federal and state water quality standards.

Jan 1, 1974

By John Frostiak

The Campbell gold operation of Placer Dome Inc. produces an arsenopyrite-sulfide concentrate that must be treated by roasting, biooxidation or pressure oxidation to obtain high gold recoveries. Pressure oxidation is a proven process that also meets Ontario's stringent environmental regulations. A comparison of biooxidation and pressure oxidation was completed early in 1990. Placer Dome selected pressure oxidation as the preferred process to replace the roaster. The commercial plant design was based on technology supplied by Sherritt Gordon. In July of 1991, the existing roaster operation was shut down and a new pressure oxidation plant was commissioned. The Campbell Red Lake Mine, in Balmertown in northwestern Ontario, is the first plant in Canada to use Sherritt Gordon's pressure oxidation technology to recover gold from a refractory ore body. A similar process has been used at Sao Bento in Brazil since 1986. The Porgera complex in Papua New Guinea also uses Sherritt's technology. At the Campbell Mine, gold occurs as either free gold or is encapsulated with sulfide minerals, mainly arsenopyrite, pyrite and pyrrhotite. These sulfide species are recovered from the ore by crushing and grinding to 80% -75. µm (200 mesh), followed by flotation. About 40% of the gold in the ore is recovered by gravity separation. The remainder reports to the ground slurry feed to flotation. The flotation concentrate averages about 55 to 60 t/d (60 to 66 stpd). A typical analysis is shown in Table 1. Before the installation of the pressure oxidation plant, the flotation concentrate was treated in a two-stage, fluid bed roasting circuit. Roaster off-gases passed through two parallel sets of cyclones, followed by electrostatic precipitators. Arsenic trioxide was captured in a four-chamber baghouse before the gas was discharged to a stack. The arsenic trioxide was sold or conveyed to an underground storage vault. The roasted calcine was fed to a gravity separation circuit and then subjected to cyanide leaching. Gold was recovered from the filtered leach solution in a Merrill-Crowe zinc precipitation circuit.

Jan 1, 1992

By Norman Haber

The Haber Gold Process (HGP) is a proprietary. hydrometallurgical extraction methodology that was developed in 1983-1984 by Norman Haber and Dr. John Lee of Haber, Inc., a small public company in Towaco, New Jersey specializing in hydrochemical process development for precious metals. It was pilot tested repeatedly in 1985 at our pilot plant in Tombstone, Arizona, with different types of gold bearing mineralization. Both Pincock, Allen and Holt (USA), and PA Technology (Australia) were involved with some of these pilot tests. The ores tested included easily cyanide-extractable oxide type gold ore from Australia, marginal heap-leach type ore from Cripple Creek, USA, and a hematite bearing ore from California. In all cases, extraction time was 6 hours or less yielding 90-99% recoveries of assayed gold values. The HGP operates as a lixivient which parts the gold from the rock matrix, yielding gold in solution in a fully recoverable form. Both precipitation methods, such as zinc participation or Carbon in Leach systems ( or Carbon in Pulp) have been shown to be feasible with this technology for the recovery of gold from the pregnant solution. Both batch vat leaching as well as continuous processing are realistic for use with the HGP. It has also been considered that the HGP might also benefit heap leaching due to several advantageous factors over cyanide. One such consideration is that the HGP can operate effectively with acidic ore types. The use of cyanide with such ores often requires attention to pH and neutralization with lime. This tends to reduce and even clog the permeability of the leach bed.

Jan 1, 1998

By Marco D. Boscardin

During subsidence, the ground surface may settle, change slope, change curvature, go into tension, and/or go into compression. In response to these ground movements, buildings and buried utilities in the subsidence area may settle, tilt, bend, distort, and sustain extension, compression and/or torsion. In order to develop measures to protect existing structures and utilities, or to design new structures and utilities to withstand potential movements in areas of subsidence, it is necessary to understand the interaction between the ground and the building or buried the utility. This paper reviews subsidence-induced ground movements, how these ground movements are transmitted to and accommodated by buildings and buried pipelines, and how these structures may alter ground movements relative to free field subsidence-induced ground movements.

Jan 1, 1986

By Andrew J. Gaber

Beginning in 1961 the Coal Research Bureau of the West Virginia University School of Mines began a program of research to investigate the potential of the magnetic separation process to remove sulfur of the pyritic form from pulverized coal. Using a so-called isodynamic magnetic separator (1) it was demonstrated that significant quantities of pyritic sulfur could be removed from coal. Pulverized coal samples representing several different coal seams were individually screened into sizes in the 48 mesh by 200 mesh (297 to 74 microns) range, and untreated and steam-air treated samples of each were processed by the magnetic separator. The results of the investigations to magnetically remove pyrite from coal were published in two separate reports issued by the Coal Research Bureau (2,3), The isodynamic magnetic separator was designed about 30 years ago for use in geological and mineralogical laboratories (1,4,5) to isolate one or more minerals exhibiting only small differences in their magnetic propertiese Specifically, to accomplish this, the air gap of the unit was designed to provide a nearly constant magnetic gradient both laterally and longitudinally in the separating zone. It is reported that mineral concentrates of 99.5 percent purity can-be produced on closely-sized fractions after several cleanings through the unit. The isodynamic magnetic separator, therefore, was not expected to process coal containing sizes smaller than 200 mesh, or to demonstrate commercial capability to process pulverized coal. The primary purpose of the Coal Research Bureau in using the unit was that of determining if the magnetic process could remove pyrite from coal, and thereby encourage further research directed toward development of acceptable full-scale processing equipment.

Jan 1, 1969

By G. Argyris

A number of important studies, ongoing environment monitoring efforts and mining and road construction projects in the lignite based electrical power production area of Amyntaio ? Ptolemais in North West Greece require an accurate and up to date model of the topography. In recognition of the importance of such a model, a project was initiated by the Laboratory of Mining Information Technology and GIS Applications in the Department of Geotechnology and Environmental Engineering of the Technological Educational Institute of Western Macedonia. A massive surface triangulation model was generated from vector data using an optimized Delaunay based method. Combined with aerial and satellite imagery, the triangulation model provides a complete 3D terrain model of the area characterized by high levels of accuracy, detail and realism. The generated model is easy to modify with new data in order to improve its detail and keep it up to date with ongoing earth moving and development operations in the area.

Jan 1, 2008

By Gail B. Knight

INTRODUCTION In May 1984, The Canadian Pacific Railway awarded to the Joint Venture of Foundation of Canada, Ltd. of Toronto, Atlas Construction Co. of Montreal, and S. A. Healy Co. of Chicago the contract for the construction of 27,000 ft of tunnel starting from the east portal. Selkirk contractors, the Joint Venture of Foundation, Atlas and Healy, which had successfully completed for CPR in 1983 the construction of both portal structures for this tunnel, studied several different alternative proposals before presenting its bid pooling each individual company's technical resources and experiences. (Foundation had just completed in association with other companies a similar tunnel project in British Columbia, and the S. A. Healy Co. could provide its experience of more than 40 miles of tunnels excavated by full face boring machines.) Among the alternatives investigated there was a fully circular tunnel to be excavated by a 30 ft diameter TBM, a full section drill and shoot proposal, and a mixed alternative, the "key hole" proposal, consisting of a TBM driven circular top heading followed by benching to design size. Technical, geological and economical considerations determined the alternative that was eventually proposed to CPR. HISTORICAL NOTES The tunnel construction parallels an existing tunnel through the Selkirk mountains that was excavated in 1885. In order to reduce the grade to 1% on the heavily loaded west bound trains, the new tunnel was at a lower elevation and lengthened to almost 9 miles. GEOTECHNICAL INFORMATION CP Rail site investigations began in 1978. The surface rocks in the tunnel construction area are metamorphosed Cambrian and Pre-Cambrian sediments; the underlying formation contains fine and coarse grained rocks presenting different degrees of metamorphism. The

Jan 1, 1987