Search Documents

By J. W. Rinard

This paper is intended to introduce "non engineers" to one of the more misunderstood pump performance parameters, NPSH (Net Positive Suction Head). This basic presentation and resultant review should provide a practical understanding of NPSH and what its importance is to pump operation and reliability.

Jan 1, 1996

By A. Mukherjee

This paper presents an analytical technique for prediction of the damaged rock zone (DRZ) around a circular drift subjected to an anisotropic stress field (analytical solution exists only for the case of hydrostatic stress field). The method can readily be adapted to micro or personal computers. Stress concentrations around the drift are calculated at the centers of small rock elements, using the analytical solutions for a hole in an infinite plate. Potential failure of a rock element is assumed to be governed by the Coulomb failure criterion. When the failure condition is exceeded for an element, the excess shear stress is transferred to the neighboring elements. Progressive failure is allowed to occur until convergence is obtained. The final configuration of the damaged rock zone so obtained can be used to assess rock support requirements, as well as modified modulus and permeability of the DRZ.

Jan 1, 1988

By Lynn B. Hales, Randy A. Ynchausti

Introduction There continues to be a large economic opportunity associated with improving process performance through advanced process control systems within the minerals industry. The basis for this opportunity lies in the inherently low efficiencies of many of the unit operations found in mineral processing plants as well as the continual variation that is present in the ores being processed. The ageless target of such control systems is improved recoveries and concentrate grades, higher processing rates and lower unit costs. Many plants are enjoying the benefits of modem, well functioning process control systems but few if any have achieved plant-wide optimization in an economical sense. As new process modeling and control technologies, such as neural networks, continue to evolve and develop, the potential for plant- wide optimization is becoming a closer reality. Neural network technology appears to have a significant potential in the general field of process control and control of mineral processing operations. Neural networks are an emerging technology that have been evolving out of the study of biological systems since the early 1940's. The first software simulation of neural computing networks was reported in 1956 by Nathanial Rochester of IBM Research during the first conference on artificial intelligence which was sponsored by the Rockefeller Foundation. Neural Networks Neural networks can be considered to be a class of computer program that perform their problem solving functions based on a rudimentary model of the human brain and how it solves problems. Traditional computer programs and even computers themselves solve problems or process data sequentially and in a deterministic manner. The human brain, on the other hand, processes data and solves problems in a massively parallel fashion. We think of computers normally in terms of having a single processing unit, sometimes a co-processor to assist in certain activities such as mathematical functions or communications, bytes of memory, processing speed and program/data storage size.

Jan 1, 1992

By Paul D. Tomlingson

A new sense of urgency permeates the mining industry concerning maintenance. Mining's continuous process environment demands around-the-clock maintenance support. And profitability conscious mining operations require that production targets be met on time - and economically. These goals require nothing less than an effective maintenance program. In turn, the effectiveness of the maintenance program depends on quality information: easily procured, complete, timely, accurate, and properly used. Information picture is changing Some of the fully integrated, mainframe maintenance information pro¬grams of better days remain. Their upkeep and cost of operation, though, is becoming more difficult to justify. Some operations, faced with production cutbacks a few years ago, downscaled and found they liked it. Now, during an upswing, these operations question the need for the more elaborate, administrative-heavy programs they used to operate. Package programs are not taking their place. Too often, the packages are vague and generic. Some vendors claim that if their offerings work in a hospital complex, they must work in an underground mine. That is not so. Maintenance information in the mining industry is different. The situation has changed There are now smaller, self-contained maintenance groups whose information needs are different. These include an electrical crew in a smelter, an underground mobile equipment shop, or a remote service shop between several distant operating pits. These working environments have changed the character of the information needed as well as the methods for obtaining and using it. Operations-maintenance link In coming back from a downturn, operations people realize that their ability to meet production targets hinges on reliable equipment and avoidance of downtime. They have become familiar with the need to use maintenance services effectively. They also want quality maintenance information. When coupled with the sense of urgency about maintenance, a business-like working environment emerges that has significant new differences in both work control and information. Work control impact Work control has been streamlined to improve communications. Supporting information has been streamlined as well. • Verbal orders are the rule rather than the exception to quickly bring a multi-craft crew to the flotation section or a pit crew to a disabled haulage truck. • Written work requests and work order forms are seldom used, or even needed. Rather, electronic work control logs permit operations to request work, maintenance to acknowledge it, get ready, and do it - quickly, without delay. • Routine servicing is triggered by operating hour accumulation (mobile equipment) or tons of throughput (fixed equipment). Operations is now taking the initiative in delivering mobile equip¬ment to the "bad order line," or switching to a bypass conveyor. Operations wants immediate follow-up reports on equipment condition.

Jan 1, 1989

By Donald A. Dahlstrom

INTRODUCTION Solid-liquid separation is an important and many times a critical step (or steps) in a mineral or coal processing plant. Some examples of typical critical separations are as follows: 1. Operating a seven to eight stage CCD thickening circuit to re¬cover almost all of the caustic and alumina trihydrate values in an alumina plant. This must be accomplished with highly scaling slurries, starting temperatures of over 100°C and operate on a closed circuit system. 2. Making a filter step operate to produce a proper moisture for the balling step so that the pellet furnace can produce a proper product. Bentonite addition must be minimized and a good quality filtrate must be maintained to prevent abrasion of the internal parts of the filter. 3. Operating a closed water system in a coal washing plant so that reclaimed water containing less than one percent suspended solids is produced for reuse to maintain beneficiation ef¬ficiency. Refuse solids must also be thickened so that they can be effectively dewatered to meet state disposal requirements. 4. Recovering phosphoric acid values from a slurry containing gypsum and other gangue solids at an elevated temperature. This must be done while minimizing wash water and maximizing P2O5 re¬covery while simultaneously minimizing scale problems. While solid-liquid separations are important to overall performance in the processing plant flowsheet, it is also a significant factor in plant costs. Capital and operating costs for all the solid-liquid separation steps (includ¬ing water reclamation for reuse) in such plants are probably between 10 and 20%. Energy consumption can also be important in these separations. For example, in the copper concentrator, it is the third largest category in energy consumption, after comminution and flotation. Obviously, solid-liquid separation steps in a plant demand proper atten¬tion in design in order to achieve both optimum performance and cost. Simultaneously, knowledge of funda¬mentals are important to improve results in existing plants.

Jan 1, 1986

By H. P. van Ormer

The objective of this paper and the developed personal computer program is not to identify or try to identify the actual total drilling cost in any Rotary Drilled Blast Bole Program. The ideas put forth here and in the computer program developed are a very accurate way to measure what is often very hard to identify and interpret -The actual direct operating cost of various drilling package combinations including comparing with available blast hole sizes and patterns

Jan 1, 1988

By H. Knorre, A. Griffiths, J. Loroesch

Introduction Hydrogen peroxide is known to the mining industry as a powerful oxidant. able to attack and to destroy cyanide, the most important leaching reagent (Knorre and Griffiths, 1984; Griffiths, 1988; Griffiths, 1988). [ ] The most recent development, however, is the use of H2O2 as an oxidant in the cyanidation of precious metals. This application may appear to be a contradiction to the above mentioned detoxification process. This can, indeed, be the case if certain conditions are not considered carefully. Degussa has developed a new process to enable the application of H2O, in this field without having any detrimental effect on the cyanide. The incentive to seek an oxygen supplier like H2O2 instead of air was the fact that one of the most important conditions for the fast dissolution of gold is the presence of physically dissolved oxygen in the pulp (Kydryk and Kellog, 1954; Warstell, 1987). [ ] Complete gold recovery within a reasonable leaching time may only be achieved if the pulp is saturated with dissolved oxygen. Gold losses in leach operations mainly occur due to the following reasons: In some cases, the saturation of oxygen in the pulp cannot be achieved by aeration due to the difficulty to transfer oxygen from the gaseous into the liquid phase. This happens, for example, in pulps with a high viscosity. In such cases, even violent aeration only results in a low concentration of dissolved oxygen in the pulp. In any case, the starting phase of leaching requires the highest amount of oxygen. Therefore, it is especially important to raise the dissolved oxygen level to saturation in the starting phase. Peroxide assisted leach process (PAL) The intention of the process is to introduce oxygen in a liquid form. As a result of intensive research work, it could be shown that hydrogen peroxide can be used as a source of oxygen in the leaching of gold ores. To avoid side reactions, the following conditions must be applied: Hydrogen peroxide must be diluted before it is added to the pulp. The dosage of H2O, must be properly regulated based on the oxygen level of the pulp. An important part of the continuous O, control is a special oxygen electrode, which resists the extremely abrasive action of the pulp.

Jan 1, 1990

By Huayang Luo, Hui Li, Wei Zhou, Gang Chen, Scott Huang

Abundant beach and offshore resources of gold deposits are demonstrated along the coast of Alaska, and Nome is one of the richest places. Considerable amounts of mineral resources data were collected and stored in geodatabase of ArcGIS. In searching for the best model for the interpretation of the Nome offshore gold placer deposit and accurate estimation of the reserve, the data were processed and visualized using ArcGIS. The gold concentration data collected from the Nome offshore deposit are of characteristics such that: (1) near lognormal distribution of data, (2) high positive skewed distribution, (3) a small number of extreme values dominating the reserve estimation, and (4) apparent anisotropy of the variogram. These characteristics make the development of an interpolation model for the gold deposit a challenging task. In this study, it is determined that five geostatistical methods provided by ArcGIS with visualization capability, i.e., Inverse Distance Weighted (IDW), Ordinary Kriging (OK), Ordinary Kriging with lognormal transformation (OK-log), Simple Kriging (SK) and Indicator Kriging (IK) are suitable candidates for the development of an interpolation model. The five algorithms are evaluated and compared with each other in the study. Cross-validation technique is employed to examine the accuracy of the five approaches. It is determined that the OK and SK algorithms are not suitable for this dataset because of the difficulty of fitting the semivariogram model despite their lower RMSE (Root-mean-square error) and the higher RMSS (Root-mean-square Standardized). The OK-log algorithm does not provide satisfactory prediction either, because it places too much weight on the role of extreme values resulting in overestimation and extremely high RMSE. Reserve estimation of each blocks is conducted using each of the interpolation methods and compared with the reserve calculated using the conventional polygon method. The IWD and IK algorithm seem to provide estimations more agreeable with the conventional polygon method.

Jan 1, 2005

By R. A. Basse, W. D. Diment, A. J. Petrina

INTRODUCTION In 1957, diamond drilling on a magnetic anomaly indicated an extensive zone of copper mineralization on what is now the Craigmont Mines property. By mid¬1958, drilling established a copper ore body. Milling commenced in September 1961 at 4536 t/d (5000 stpd) and by the end of October 1977 the mine had produced 339 662.04 t (374,363.9 st) of copper. At present, two-thirds of the mill feed is derived from underground operations and one-third from low-grade surface stockpiles. Craigmont Mines is situated 209 km (130 air miles) northeast of Vancouver (see Fig. 1), 16 km (10 miles) west of the town of Merritt, a logging, ranching, and mining community of about 7000 people. It is serviced by paved highways, Canadian Pacific Railway, British Columbia Hydro, and Inland Natural Gas Co. Water is pumped from the Nicola River, a distance of 6 km (4 miles) and a lift of 244 m (800 ft). In March 1967, the open pit mining operations at Craigmont Mines reached their economic limit and were suspended. Before this, it had been decided that a sub¬level caving method of underground mining would be used to supply ore to the concentrator after the cessation of open pit production. This chapter describes the fac¬tors influencing the choice of mining method, some of the problems encountered, mining practices, and results. GEOLOGY The ore bodies of upper Triassic age are located in a limy horizon striking east-west, closely paralleling the intrusive Guichon batholith, bounded on the south by rhyolites and on the north by graywackes, and dipping steeply to the south (Figs. 2a, b). The ore bodies are relatively narrow with a maxi¬mum width of 79 m (260 ft), a combined strike length of 853 m (2800 ft), and a vertical extent of 610 m (2000 ft). Chalcopyrite is virtually the only copper mineral, and 20% of the ore zone consists of acid solu¬ble magnetite and hematite. The area has been subjected to considerable faulting and brecciation, which is a major factor in the mining operation. Total geological reserves, at 0.7% Cu cutoff, for the deposit were 22 316 743 t (24,600,000 st) at 1.89% Cu. An additional 5 236 270 t (5,772,000 st) at 0.6% Cu were mined from the open pit. Ground Conditions The waste rocks-graywacke, andesites, and diorite -are relatively incompetent due to the high degree of fracturing and jointing, and all require varying degrees of support. The ore zones are somewhat less fractured; ground support is still required, however, although to a lesser extent than in the country rock. Ground conditions in the main ore body are better than in the smaller, nar¬rower ore bodies. Clayey fault gouge is present in most of the faults; gouge zones may be up to 6 or 9 m (20 or 30 ft) wide. The main ground problems are associated with local weakness rather than pressure. Shape of Ore Bodies (Figs. 2a, b and 3a, b) The main No. 1 ore body is approximately 244 m (800 ft) long and 46 m (150 ft) wide. It extends ver¬tically from the original top of the open pit at 4200 ele¬vation to just below the 3060 level. The No. 2 ore body is approximately 304 m (1000 ft) long, varies from stringer width at the extremities up to 79 m (260 ft) wide, and extends from 3060 level to 2400 level. Both these ore bodies have extensions re¬sulting in additional small irregular bodies. Ore bodies are mostly steep dipping, though part of the Wing ore body, an extension of No. 2 ore body, dips at 0.87 rad (50'). This ore body varies in size, but is approximately 122 m (400 ft) long, 21 m (70 ft) wide, and about 213 m (700 ft) high. No. 1 Limb ore body is a narrow extension of the No. I Main with a vertical extent of 137 m (450 ft), average width of 18 ft (60 ft), a strike length of 152 m (500 ft), and dips steeply at 1.4 rad (80°). No. 1 East is an eastern extension of the No. 1 Main with a vertical extent of 183 m (600 ft), a strike length of 91 m (300 ft), an average width of 30 m (100 ft), and dips at 1.2 to 1.4 rad (70 to 80°). No. 1 South is at the upper west end of the open pit with a vertical extent of 76 m (250 ft), a strike length

Jan 1, 1982

By E. Baliktsis

PPC (Public Power Corporation) operates a new power plant at the South-West part of Crete. Recently the extension of the Power Plant started. ATHENA SA the main contractor of the project assigned to EXORIXI SA the implementation of a blast vibration monitoring program and prevention-evaluation of risks caused by construction blastings inside or very close to the operating part of the power station. The blasting parameters and characteristic elements that had been evaluated, the measures that had been taken and materialized, the overall risk management and the results of the whole program are presented in this paper.

Jan 1, 2006

By Steve Crewdson

High tonnage hoisting of materials by vertical conveyors through deep shafts is a relatively new concept in mining that is proving to be effective. The development of the Pocketlift® belt by Metso Flexowell, located in Moers, Germany, enabled the installation of a deep shaft vertical conveyor in 2002. This application followed years of design and operational experience gained in medium-depth shafts around the world. The design, manufacture, installation and operational experience of an 1,818 tonnes capacity, 273 meters vertical lift, Pocketlift® belt system at the White County Coal Pattiki 2 Mine is the subject of this work

Jan 1, 2004

By J. Kalnejais

Discovered in 1896, the Sons of Gwalia orebody was initially mined by unground methods. Euring the mine's uderground operations workings reached a vertical depth of 1080 metres. The same orebody is now being mined by open cut methods. The present operation mines a broad envelope of mineralisation surrounding old stopes, whereas the original underground operation concentrated on mining high grade parts of the Gwalia Lode System. Underground mining continued up to 1963 when operations ceased due to high operating costs and the low grade of ore mined. In 1984 a new company, Sons of Gwalia NL, commenced open cut operations.

Jan 1, 1989

By George E. Aikens

Prolonged subzero climatic conditions impose some unique engineering problems for the developer and operator of open-pit mines in the Far North. The remoteness of the job site and the extremely cold, long, dark winters severely tax both man and machine in the quest for the Arctic's rich mineral wealth. Undoubtedly the singular most troublesome problem for the engineer is Permafrost which underlies about 201o of the land area of the world and about 85% of the state of Alaska. Permafrost has its impact on building construction and mine excavation, while posing a more pervasive threat to the-delicate ecologic balance within the Arctic wilderness. Yet the difficulties associated with mining up North may not be as overwhelming as has been previously supposed. For example, the lowest temperature recorded at Point Barrow is -560F, whereas Montana has recorded -69.7° F.. There are no specially designed machines for mining and construction in the Arctic, and efficient equipment utilization is maintained through proper operation and servicing techniques. However, neither equipment or people can be assumed to function normally at -40°F. Special techniques in drilling, blasting, and ripping are being used to yield economically competitive ores. Overall, a fundamental understanding of the nature of Permafrost will allow the engineer to deal expeditiously with an Arctic mining venture and at the same time to deal fairly with Arctic environment.

Jan 1, 1972

By G. A. Hope, K. Watling, R. Woods, I. Chandra, I. M. Ritchie

This paper presents two aspects of gold leaching research and development. The first section of the paper covers the development of innovative gold leaching processes. The research in this area has concentrated on the development of new thiosulfate leaching systems which use Fe(III) stabilized by ligands as the oxidant in place of copper(II)+ammonia. The second section will cover the development of innovative techniques such as surface enhanced Raman scattering (SERS) to study the leaching of gold in cyanide solutions. It will be shown that the use of in-situ SERS yields information which cannot be obtained using other methodologies.

Jan 1, 2005

By Gastón Díiaz, Enzo Carranza Meza

El Teniente Mine of Codelco-Chile, located at Los Andes Range of Mountains, 90 kilometers South far from Santiago, the capital city, has been exploited for more than 90 years, with over 1000 million tonnes of copper ore extraction. No doubt, this particular record, has been possible to achieve due to an efficient combination of human and technological efforts in the exploitation of one of the biggest ore deposits of the world. Throughout times, the exploitation has evolved from a mainly manual one to a highly mechanized exploitation. Notwithstanding, different and several geomechanical problems that occurred in one of its areas, increased the risks to personnel that should normally operate large equipments in its working face. This last condition, forced El Teniente mine to design and develop systems and technologies that would allow the use of tele-operated LHD, picking hammers and drilling equipment (jumbos) from a safe zone. Currently, El Teniente Mine is using in its extractive works equipment such as LHD, picking hammers, and drilling Jumbos, that can be manually or teleoperated commanded from a Central Control Room located one kilometer away from the production area. In general, a new technological era has been opened in the mining exploitation at El Teniente: the exploitation era with telecommanded robots.

Jan 1, 1998

By S. K. Kawatra

Outokumpu Electronics has designed a new on-line coal slurry ash analyzer, based on an instrument developed at Michigan Technological University. The primary goal was to build an accurate instrument at the lowest possible cost. The instrument determines ash content from measurements of X-ray backscatter, iron K, fluorescence, and low-energy y-ray absorption. It is capable of measuring the ash content with a standard error of 1.1% ash over an analysis range of 9-21% ash and 7-22% solids. The analyzer was tested on coals from United States, Poland, Great Britain and the USSR.

Jan 1, 1993

By G. Deschenes, P. J. H. Prud'homme

A laboratory study was carried out to evaluate the effect of oxygen and lead nitrate on the recovery of gold by cyanidation of a free milling gold ore, which contains 0.4 % copper as chalcopyrite. Efficient gold extraction is achieved only under specific conditions. The recovery of gold was increased from less than 90% to up to 98% by addition of lead nitrate. In the pre-leaching, the kinetics of oxidation of soluble sulphides are not an accurate indication for the length of the treatment. Even though the consumption of cyanide was reduced due to the inhibition of the dissolution of chalcopyrite by increasing additions of lead nitrate, cyanide consumption had to the held above 1.85 kg/t to maintain good recovery of gold. The continued addition of lead nitrate above 300 git had no impact on the recovery of gold. It was also found that the addition of lead nitrate at the start of cyanidation gave the same performance as when added during pre-leaching. The addition of oxygen increased the recovery of gold by 1.5%. The concentration ofNaCN had to be maintained in the range of700 mg/L because of the high concentration of copper in solution. The recovery of gold dropped significantly when the average NaCN concentration fell below 640 mg/L. Application of the findings of the laboratory study at the industrial scale led to improved plant performance.

Jan 1, 1997

By Odd G. Askilsrud, Steinar Johannessen

New powerplants, tunnels and dams are currently under construction at Meraaker to triple the annual power production of a nearly 100 year old power scheme. A total of 44 km tunnels with cross sections varying from 7 m2 to 32 m2 have been excavated in hard rock formations. Ten kilometers were excavated by a High Performance Tunnel Boring Machine (HP TBM). The remaining tunnels have been completed by the drill and blast method, using modem proven equipment and procedures. This paper gives special attention to the TBM drive and equipment selection, including, planning, site organization and performance.

Jan 1, 1993

By R. H. King, R. E. Cameron

Mine managers need better information to locate new opportunities and then to assess the effect of their decisions. We are developing the Intelligent Decision Support System (IDSS) and its two major modules, the Pattern Recognition System (PRS) and the Knowledge Representation Subsystem (KRS) to automatically provide the information from monitoring system sensors. This paper focuses on the KRS Algorithms that extract key information from lists of time-study type event sequences. Because a static system cannot operate effectively in a dynamic mining environment, we are prototyping an index- based technique that allows the system to adapt itself to this dynamic environment.

Jan 1, 1991

By C. M. Rastle

Resource Technology Associates (RTA) has developed a flocculation-flotation process that increases phosphate recoveries from current operating plants. A major advantage of the process is the ability to float the phosphate from the matrix without a preliminary separation to remove the slimes. A majority of the material that is now discarded in the slime fraction will be recovered in the new process. The process can also be used to recover phosphate material from current slime ponds either as a separate feed or mixed with matrix material. Flotation tails from the process demonstrate improved dewatering characteristics then those seen from conventional float tails.

Jan 1, 1988