Search Documents

By R. D. Cook, J. L. Johnson

"Measuring mud bed level in a sedimentation device is an important control variable. Methods used to date for this purpose have had limited success providing continuous, consistent measurements at a reasonable price. This paper describes a new instrument for detecting the mud bed / liquor interface as well as bed density profiles. The state of the bed is measured directly with sensors located in the thickener. Data from bench-scale and full-scale tests show that the bed level is well defined and easily detected. In addition, full-scale testing revealed unprecedented information about thickener beds. Variation in bed density gave new insight into thickener bed dynamics, providing design and control opportunities never before possible. This novel instrument can significantly improve thickener control by providing reliable and consistent bed level measurements. It is also capable of measuring bed density profiles that can potentially identify significant operating problems early enough to take corrective action before experiencing costly shut downs. INTRODUCTION Numerous studies and papers have been devoted to the subject of thickener design and operation to achieve specified throughput and discharge densities. Mathematical models have been developed that present methods for sizing thickeners and predicting performance under varying process conditions. The compression effect of deeper beds on dewatering performance is a recognized phenomenon (Wilhelm and Naide 1981). This is one variable of many that are inter-related and influence thickener performance. For example in the steady-state, continuous operation of a thickener, if the solids feed rate increases and the bed level remains the same, the underflow discharge rate must increase with the result of solids concentration being lower. The interactions of these parameters are at the heart of thickener models. One such model (Burger and Narvaez 2007), predicts solids concentration profiles increasing downward and discontinuities between settling zones. This model uses sediment height (bed level) as a parameter that influences capacity calculations to achieve the specified solids concentration of the underflow. Knowing the bed depth is critical to maintaining stable thickener operation. Implicit in these modeling strategies are some basic assumptions such as homogeneous distribution of solids in the different settling zones, plug flow of solids through the settling zones and steady state operation of the thickener. The accuracy of these assumptions has not been verified because there has been little visibility inside the bed of full size operating thickeners. Testing of the instrument presented in this paper demonstrates that it provides a degree of visibility of the dynamics in a thickener not previously possible and indicates that the basic assumptions of the modeling strategies may not be completely accurate."

Jan 1, 2015

By Phillip J. Maddex

Transportation is a major part of yours in the industrial minerals industry. Whereas federal income taxes merely take 50 per cent of your firms profits, transportation cost may take 50 per cent of the gross realization - selling price plus transportation - on your product, f. o. b. customers plant.

Jan 1, 1969

By I. J. Dowdeswell

Perspective Man is a model maker. Throughout recorded history man has-used models both to provide insights into the workings of the processes which surround him and as a step towards the eventual control of those processes. These models have covered the field from extremely large systems (solar and celestial. models) to infinitesimally small systems (sub-atomic .and atomic models). Models have been developed for social systems, ecological systems, biological systems and economic systems: all fields of human endeavour contain the fruits of this restless model-making. The Role of Models Since the evidence of mans' industry in formulating models is so abundant, it is worthwhile stating some of the reasons. Based on the simple definition that "a model is a convenient and useful representation of some facet of the 'real' world", then a model provides a means for: 1. Understanding the thing being studied. 2. Communicating that understanding to others. 3. Manipulating the thing being modelled. The common denominator implicit in these reasons is that- improved control is the. objective off all modelling or simulation work. Improved control shows itself either directly by the development of devices which perform the control functions or indirectly by improvement in the decision making process itself. For example, in a process plant, a suitable model of part of the process could lead either to the use of automatic control devices such as set-point controllers or to the implementation of instructions (pre-defined decisions) which permit the operator to better control the process. Typical process control systems use both of these since fully automatic control is restricted to processes where the required information can be effectively measured.

Jan 1, 1972

This paper reports on the behavior of mercury and its compounds during the thiosulfate leaching and recovery of gold. Thiosulfate solutions are shown to dissolve Hg0 and Hg2Cl2 to a similar extent as cyanide, but the leaching of HgS is significantly slower in thiosulfate solutions compared to cyanide. Hence, the use of thiosulfate may be an option for treating ores containing high levels of cinnabar, especially since the legislation concerning the discharge or sale of mercury is becoming more restrictive. The deportment of mercury during gold thiosulfate loading and recovery using a strongly basic anion-exchange resin was also studied. Although the mercury thiosulfate complex loads on the resin, the adsorption is weaker than for gold, with an equilibrium constant between gold and mercury of 51. Resin loaded with gold, mercury and copper was pre-eluted with thiosulfate (to remove copper) and eluted with a chloride and sulfite eluant. The majority of the mercury is eluted by the eluant and, hence, its deportment closely follows gold and the eluate would need to be treated to remove either mercury dur-ing or prior to gold electrowinning.

Jan 1, 2010

By H. S. Puttanna

Bound water plays an important role in the processing and utilization of numerous materials and mineral processing systems. The fundamental nature of this near surface bound (vicinal) water is yet to be understood in its complete detail. The objective of this paper is to use dielectric measurements to characterize the bound water near hydrophobic and hydrophilic oxide surfaces. It is anticipated that a combination of dielectric property measurements and characteristic relaxation times will allow for more effective analysis of the interfacial water.

Jan 1, 1992

By H. A. Oliveira, A. Azevedo

Physical and chemical characterization and solid/liquid separation of turbid waters from a river affected by an iron tailing rupture disaster (Gualaxo do Norte River, Brazil) were studied at bench scale. Parameters such as turbidity, pH, surface tension, electrical conductivity, total suspended solids (TSS), particle size distribution (micro- and nanoparticles), and zeta potential were analyzed from samples collected at three different river depths. The results in all samples showed the presence of micro- and nanoparticles, ranging in diameters from 100 nm to 200 μm. Best results for flocculation and settling were obtained at pH 7.5, through an innovative combination of eco-friendly reagents: (i) ferric hydroxide precipitates (10 mg L−1 Fe3+) to sweep (enmesh) the dispersed solids and (ii) gelatinized starch (5 mg L−1 ) to form large flocs. The results showed removals between 90 and 100% of total suspended solids (micro- and nanoparticles), resulting in clear water with residual turbidity < 7 NTU. It is believed that this innovative alternative has a high potential for flocculating and treating the turbid water at Gualaxo do Norte River, assisting the water treatment stations.

By T. Hollingsworth

The Boddington Gold Mine, located near Perth in Western Australia, has recently completed the construction of a new process plant. An overland conveyor system was installed to convey the ore from the primary crusher to the process plant. This paper will discuss the overland conveyor?s mechanical design including dynamic analysis and the selection of primary mechanical and electrical components.

Jan 1, 2010

By T. Leftwich, G. Faison, K. Pavlich, R. Borden, S. Pavlou

Recent regulatory and policy initiatives under the Resource Conservation and Recovery Act (RCRA), and the Comprehensive Environmental Response Compensation and Liability Act (CERCLA), will have a significant effect in risk reduction requirements for the mining and minerals processing industry. For example, Congress is considering regulating 20 special wastes from the processing of ore and minerals through RCRA Subtitle D and TSCA. The performance of risk analyses and environmental planning at mining projects is often driven by Federal and state regulatory standards. Recent regulatory and policy initiatives by the Environmental Protection Agency under the Resource Conservation and Recovery Act (RCRA), and the Comprehensive Environmental Response Compensation and Liability Act (CERCLA), will have a significant effect on environmental planning and risk reduction programs for mining and minerals processing. Regulatory programs implemented under other Federal laws including the Safe Drinking Water Act, Clean Water Act, and Clean Air Act will also impact industry practices. This paper provides: 1) a brief overview of mining waste and mining waste management, and 2) a description of these regulatory initiatives and a discussion on the impacts of new requirements on environmental and risk reduction programs in the mining industry.

Jan 1, 1992

Due to the relatively remote location of the St. Anthony Mine, the high cost of transportation and milling, plus the low grade nature of the deposit, the United Nuclear Corporation began investigating methods of mechanical upgrading approximately eighteen moths ago. This investigation culminated in the installation of Model 17 and Model 18 ore sorting machines. The machines are marketed in the United States and Canada by Ore Sorters of Canada (Ltd.). The installation of this advanced technology will enable United Nuclear Corporation to fully realize the residual potential of St. Anthony.

Jan 1, 1979

By D. E. Ranta, John G. Stone

One of the steps in an ore reserve estimate is customarily a rigorous calculation of the in situ grade of the orebody itself. The result of this calculation is usually reduced by some purely arbitrary factor to force the calculation to agree with the observed grade of ore actually mined. The failure of the calculation to realistically depict the grade of ore actually extracted is in many instances not the result of either an incorrect calculation procedure or of sloppy mining practice, but is a direct consequence of unsuspected irregularities in the contact between the orebody and the surrounding wall rock. A pattern of holes spaced at 1.5-3.Om foot intervals, drilled as part of a pre-development program, will often reveal that a presumed "regular&apos; ore/waste contact is, in fact, so highly irregular that it will be next to impossible to separate ore from waste during mining. In such an instance, &apos;fingers&apos; of waste projecting into the mining block will substitute for equal volumes of ore left outside the mining limits. As a result, the grade of material actually mined will be less than the grade envisioned for the orebody. The volume of waste substituting for ore in the mining block is about 0.4X, where X = the average error in projecting the ore/waste contact between alternate holes in the test pattern, and is expressed in units of volume per unit of area of the contact surface.

Jan 1, 1992

By R. Bhaskar

The advantages of recirculation of air in underground mines have been well recognized, and several papers have been written on the subject. Issues of concern to the various segments of the mining industry relate to the health and safety of workers, specifically, methane and respirable dust build-up in the air, high humidity and temperature at the work face. This paper presents a survey of various studies pertaining to recirculation as a prelude to the experimental and quantitative studies performed by the authors. Experiments were performed at a trona mine on the transportation and deposition of dust along the return airways, for three different velocities. Modeling studies were performed using dust deposition models. The model predicted data were compared with experimental data in order to lay the foundation for the development of advanced predictor models for recirculation in trona mines. Two models for dust deposition were analyzed. The model predicted data are in divergence from the experimental data, indicating the need to develop better models.

Jan 1, 1992

By A. Anani, K. Awuah-Offei

"Accounting for changing duty cycles in equipment matching maximizes equipment utilization and productivity. The objective of this study is to investigate if the optimal number of shuttle cars for a particular panel width is optimal in different segments of the panel. In this study, discrete event simulation (DES) is used to determine the optimal number of cars that maximizes productivity in each segment. Data from a real-life mine is used to validate the model. The study shows that the optimal number of cars for the entire panel may not be optimal for some of the defined segments. INTRODUCTION Fleet optimization is important for efficient mine management. Deploying the optimal fleet minimizes the capital and operating expenditure for particular operating conditions and production targets. In an operating mine, with an already existing fleet, deploying the optimal fleet maximizes productivity or minimizes production cost with the available resources. Hence, a lot of research has focused on how to determine the optimal fleet size for a mining operation, given particular operating conditions. Mine managers and engineers have successfully used discrete event simulation (DES) to determine the optimal fleet size in mines (Michalakopoulos, Roumpos, Galetakis, & Panagiotou, 2015; Awuah-Offei, Osei, & Askari-Nasab, 2011; Ben-Awuah, Kalantari, Pourrahimian, & Askari-Nasab, 2010; Govinda Raj, Vardhan, & Rao, 2009; Yuriy & Vayenas, 2008; Kwame Awuah-Offei, Temeng, & Al-Hassan, 2003). In most cases, the published work on this topic involves determining the number of hauling units to be matched to a loading unit. Many of these examples involve truck-shovel optimization. There are, however, some underground mining examples. For instance, we recently concluded work that involves fleet optimization in underground room and pillar (R&P) coal mining (Awuah-Offei & Anani, 2015). Generally, when DES is used in fleet optimization it involves three steps: (1) Build a valid model of the mining system capable of predicting the required outputs with varying fleet composition; (2) Design and conduct experiments that vary the fleet composition across all feasible options; and (3) Determine the optimal fleet based on the results of the simulation experiments. A major decision in the first step is which outputs should be modeled. Some examples in the literature include productivity, unit cost, loader utilization, queue length, and hauler waiting times (Awuah-Offei et al., 2011; Govinda Raj et al., 2009; Kwame Awuah-Offei et al., 2003). Often, more than one of these outputs are simulated and considered as the objective function of the optimization."

Jan 1, 2016

By Martin Valeri

The operation described in-this paper will be confined to the Nemacolin Mine of The Buckeye Coal company, Nemacolin, Pennsylvania.&apos; This mine is-located on the Monongahela River approximately sixty miles south of Pittsburgh. The mining is in the Pittsburgh seam that has an average thickness of 88 to 90 inches. The current practice is to mine approximately 80 inches, leaving 8 to 10 inches of roof coal. All of the coal produced is used solely for by-product coking by the parent Youngstown Sheet & Tube Company, Youngstown, Ohio. Eight to ten inches of top coal are left by the miners to prevent air slacking of the draw slate. In addition, this top coal which will float at the washing gravity has a very high ash and sulphur content, and when mined, seriously affects the quality of the clean coal product.

Jan 1, 1961

By R. W. M. Lai

The study of flotation kinetics was first reported by Garcia-Zuniga1 in 1935. Since then, literature on the subject has grown with the time. 2-19 Although there is an abundance of flotation kinet¬ics models available in the literature to describe flo¬tation systems, they are mostly of academic interest and are seldom applicable for use in the industrial environment. Several reasons contribute to the wide gap in the industrial -application of the academic models. These include: 1) the lack of generality in the model, e.g., the model is limited to certain size ranges; 14 2) the academic models involve complicated mathematics; 5,6,10,11 3) confusion about the order of the flo¬tation rate, e.g., several authors proposed a first order rate model, 1,15,16 whereas the others propagated a second order rate model: 2,17,18,194) the use of an unrealistic rigid value, such as the use of a maximum recovery of 100%, 5,8,19 which is unrealistic in industrial operations; and 5) the use of graphs that confuse the reader rather than interpret information. 2,3,10 This paper intends to introduce a simple and easy to understand empirical flotation kinetics model along with a way of presenting the model in an informative graphical form, which should stimulate the interest of other practical engineers to become concerned with practical application within the mineral industry.

Jan 1, 1982

By V. W. Smith

For the past 50 years, the primary crushing of stone at the Dolase Bros. Co. Richards Spur Quarry. 13 miles north of Lawton, Oklahoma, has been accomplished by a Traylor 42-inch gyratory crusher. The production capacity of the primary system, consisting of a feeder, grizzly, and the gyratory crusher, was approximately 2100 tons per hour. Shot-down scone was hauled from the working face about one mile to the feeder by a fleet of Caterpillar Model 773&apos;s and WABCO 60- and 65-ton trucks. In order to maintain production, nine to ten trucks and four Caterpillar Model 992 front-end loaders were required to be operational at all times.

Jan 1, 1986

By Mark S. Stagg, Michael J. Nutting, Douglas R. Barlet

Single-row bench blasts at a reduced scale in the field were used to study the effects of delay time on fragmentation. Nine shots with a spacing of 21 in. and a burden of 15 in. (S/B = 1.4) and nine shots with a spacing of 30 in. and a burden of 15 in. (S/B = 2.0) were completely screened to determine particle size distributions. Delay intervals between holes ranged from 0 to 45 msec, corresponding to effective delay intervals ranging from 0 to 36 msec per foot of burden. Each shot was instrumented with strain and pressure gages to measure in situ blast dynamics and to evaluate interactions between blastholes. Finer overall fragmentation was produced for shots with delay intervals between 1 and 17 msec per foot of burden. Only for shots within this optimum delay range was it observed that the strains induced by stress waves constructively interacted with strains induced by gas pres- sure from an earlier detonated hole. Coarsest fragmentation resulted at delay intervals less than 1 msec/ft, where stress waves from each hole were observed to interact destructively, and at delay intervals greater than 24 msec/ft, where no inter- action between holes was observed, indicating a condition that can be considered as the firing of single hole shots independently.

Jan 1, 1986

By V. B. Achanti

Laboratory studies were carried out at West Virginia University to investigate the rock fragmentation mechanism by continuous miners using an automated rotary cutting simulator. The primary factors influencing the: fragmentation process were found to be: bit spacing, bit geometry, depth of cut, and cutting drum rotational speed. This paper presents the influence of these parameters in achieving optimum energy consumption and minimizing dust generation during rock fragmentation process. Three bits were used simultaneously on Indiana limestone while the bit tip angle was varied from 60° to 90°. Bit spacing was varied from 2.54 cm (1 in.) to 5.08 cm (2 in.) while the cutting process was assessed for varying cutting depths. Respirable dust generated during the course of the experiments was analyzed utilizing cascade impactors. Assessment of these parameters has led to a better understanding of the cutting mechanism by continuous miners in terms of energy consumption and dust generation.

Jan 1, 1997

By Carl D. Broadbent

The goal of slope mechanics is to achieve efficient and safe pit slopes. In the case of ultimate mine slopes the objective is to minimize the stripping ratio by steepening the slopes to their maximum stable limit. On the other hand, the inclination of working slopes is normally established by operating space requirements and the function of slope mechanics should be the continuous surveillance of slope conditions to assure long-term stability and to provide timely warning of impending slides so that corrective measures may be incorporated in production planning. In 1956 Kennecott instituted a program to provide the resources necessary to develop and maintain a slope mechanics capability, including technical knowledge, engineers, and instruments. Although the goal has not been fully achieved, very significant progress has been made. Other papers (3, 4, 7, 8, & 12) have described the purposes and detailed results of the most recent study carried out at the Kimbley Pit. The study has provided valuable experience and has given the industry a three dimensional picture of the stability variables that influence a mine slope. The study has better defined those areas which require further investigation and has indicated those design and analytical techniques which can be used with confidence. In effect, the study has paved the way for the next step; that of refining the design process and applying it for profit.

Jan 1, 1968

By L. F. McHugh

Molybdenum conversion operations discussed in this paper encompass all major operations commercially used to upgrade molybdenite concentrates to various refined products. More emphasis is placed on discussion of key pyrometallurgical unit operations. These operations conducted at Metec include roasting, sublimation, and hydrogen reduction

Jan 1, 1986

By Carl Hansen

Sonora Mining Corporation (SMC) operates the 6,000 tonne per day Jamestown open pit gold mine in the Mother Lode district of California. The mine has been in operation since January, 1987, and has produced approximately 7,800 kilograms of gold since start-up. The property consists of five ore bodies lying along a five kilometer stretch of the famous Mother Lode vein system. At present, only the Harvard ore body is being mined. The Harvard pit is centered around a historic underground mine of the same name that was operated from 1896 to 1916. The present ore body averages 2.5 grams gold per tonne as free milling gold and auriferous pyrite. The project consists of the open pit mine and concentrator complex in Tuolumne County, California, and a carbon-in-pulp leach plant located near Yerington, Nevada.

Jan 1, 1990