Search Documents

By A. Sandberg, M. Nzotta, Du Sichen, N. N. Tripathi, K. Beskow

The present study was carried out to investigate the impact of slag refractory lining reactions on the formation of inclusions during ladle treatment of steel. The experiments were conducted on an industrial scale in the ladle at Uddeholm Tooling AB in Hagfors, Sweden. The inclusion chemistry and population during ladle treatment were studied along with the composition of the ladle glaze, taken from the ladle lining. The inclusions in the steel were classified into four groups according to the Swedish standard SS 111116. SEM/EDS analyses were carried out to identify the phases present in both the inclusions and the ladle glaze. The number of inclusions in the steel before deoxidation was found to increase with the ladle age, i.e. the number of times the ladle had been in use. A similar increase was also found after vacuum degassing and before casting. A great portion of inclusions before casting was found to be supplied by ladle glaze. This observation was further confirmed and explained by thermodynamic analysis. The present results show that ladle glaze is a major source of inclusions in the ladle at Uddeholm Tooling. Keywords: Slag/ refractory/ lining?reactions, ladle glaze, inclusions, inclusion chemistry, ladle treatment

Jan 1, 2004

By H. Sekimoto, T. Matsuoka, K. Yasuhara, M. Ota, S. Akutagawa

A magnetic anisotropy sensor is used for nondestructive measurement of stress on surfaces of a ferromagnetic material, such as steel. The sensor is built on the principle of the magneto-strictive effect in which changes in magnetic permeability due to deformation of the material is measured in a nondestructive manner, which then can be translated into the absolute values of stresses existing on the surface. This technique was applied to measure stresses of H-beams used in tunnels. The results show that this method could be one of the promising technologies for non-destructive stress measurement for safe construction of underground structures. Une sonde magnétique anisotropique est utilisée pour des mesures non-destructives de stress sur la surface d' unmétal ferromagnétique, comme l'acier. La sonde est construite sur le principe de l'effet magnéto-strictif dans lequel les changements dans la perméabilité magnétique due à la déformation du metal est mesurée avec une manière non-destructive, qui peut être alors traduite en valeurs absolues des stress existants à la surface. Cette technique a été appliquée pour la mesure de stress des poutres en H utilisées dans les tunnels. Les résultats montrent que cette méthode peut être l'une des technologies promet tantes concernant les mesures non-destructives de stress pour des constructions sûres de strcutures souterraines. Ein magnetischer Anisotropie-Sensor wird für die zerstörungsfreie Messung von Spannungen an Oberflächenvon ferromagnetischen Materialien wie z.B. Stahl verwendet. Der Sensor kann Änderungen in der magnetischen Durchlässigkeit auf Grund von Verformungen des Materials erkennen, die dann in Absolutwerte der Spannungen an der Oberfläche umgerechnet werden können. Die Methode wurde auf Messung von Spannungenvon H-Balken in Tunnels angewendet. Ergebnisse zeigen, dass dies eine vielversprechende Methode für diezerstörungefreie Messung im Tiefbau ist.

Jan 1, 2003

By T. Lindstad, S. Gaal, S. Hansen, S. Prytz

The SINTEF SiO-reactivity test, developed by Tuset and Raaness in the 1970?s, is a recognised method of characterising the ?reactivity? of carbonaceous reactants, used in the ferrosilicon and silicon metal industries. Recently, the test has been updated, which has resulted in the development of an extended and improved SINTEF SiO reactivity test. This has included updating the test reactor, control system, data-logging, handling and preparation of carbonaceous materials to be tested and measurement procedure. The scientific basis has been re-assessed, resulting in a new interpretation of the test results. The repeatability of the test has improved significantly, especially through system automation. In the ?old? test, the kinetics of the reaction: SiO(g) + 2C(s) = SiC(s) + CO(g) for a specific carbonaceous material was characterised solely by the ?R10? parameter, the volume of SiO(g) which passes un-reacted through the coke-bed as the concentration of CO in the outlet gas decreases from 18 to 10%. As both the kinetics and obtainable conversion of SiO to SiC for a reductant is of importance to the ferroalloy producer, the new SINTEF SiO reactivity test ranks carbon materials both according to degree of conversion and reaction rate. From research carried out on the test in the past couple of years at SINTEF and NTNU, it has also become clear that some of the reactions taking place in the test reactor are more complex than previously assumed. As an example, it was previously assumed that the condensation reaction of SiO gas in the condensation chamber of the test reactor can be described as: 2 SiO(g) = Si(l,s) + SiO2(s). However, it has been established that the side-reaction: CO(g) + 2Si(l) = SiC(s) + SiO(g) causes approximately 10% of the total volume of CO to react to SiC and SiO2 in the condensation chamber. This means that some back-reaction i.e., the reverse SiO-generator reaction 3SiO(g) + CO(g) = 2SiO2 + SiC also takes place in the condensation chamber. In the new SINTEF test, the %CO versus time curves are therefore corrected in order to describe the effect of the reaction between SiO(g) and C(s) studied i.e., SiO(g) + 2C(s) = SiC(s) + CO(g). A correction-formula for this purpose is presented.

Jan 1, 2007

By J. Kerr

The first stage of the development of a new modified 201-type low nickel austenitic stainless steel is described in this paper. The alloy is intended for use as a structural alloy, and so requires a yield strength >400MPa as well as acceptable weldability and toughness. The low nickel content will give a lower material cost in comparison to more conventional austenitic grades, and the processing route is required to be similar to that of Type 304 to keep the processing cost low. The base alloy was designed using empirical methods developed for stainless steel, and the properties of the base alloy were verified using a range of small-scale melts. The base alloy had a 0.2% proof strength of ~320-400MPa, and so it is planned to use V additions of ~0.15% to bring about precipitation strengthening in the hot rolled condition, so raising the alloy?s proof strength above the 400MPa minimum.

Jan 1, 2004

By W. Bryszewski

As a result of strategic analysis in respect of the needs for air quality management a new advanced and holistic approach to air quality management process was introduced in the North West Province (NWP) of South Africa. The process is based on the principle of co-operative management. It involves both active participation of all Interested and Affected Parties (I&AP) and the holistic approach to solving problems with the underlying principles of shared ownership and sustainable development. The process consists of the followings phases: ? Industrial process quantification ? Quantification of impacts ? Formulation of the required control measures ? Definitions of certificate conditions ? Implementation of an adequate compliance management system at company level ? Ongoing co-operative air quality and system management with the strategic objective of continuous improvements The system has been successfully introduced in the North Province and proved to be an effective management tool and aids assurance of sustained environmental ability to cope with the pressure of industrial developments. The benefits and effectiveness are discussed using Hernic Ferrochrome as an example. Hernic Ferrochrome is one of the first companies, which successfully implemented this system.

Jan 1, 2004

By B. J. Kloppers, J. V. Z. Visser, C. J. Horn

"The long-term plan (LTP) in a mineral resource company is defined by the quality of the mineral resource and represents the result of a series of trade-offs to fulfil internal organizational as well as external business and legislative requirements, ensuring ultimate delivery on the defined organizational strategy.The LTP should as a whole align to a coherent and well-defined organizational strategy, working towards a clearly defined objective while still allowing a tactical response to short-term requirements of the organization. The ability to respond tactically to changes in environment, like the unprecedented five-month strike in 2014 on the platinum belt following the 2012 Marikana incident, is a measure of the flexibility of the plan given the agreed strategy.This paper describes the Lonmin process of linking company strategy with long-term planning, tactical planning, and the execution of the plan through an annual planning cycle to maximize organizational flexibility. This flexibility enables mining companies to respond to the many internal and external forces that impact on both strategy formulation and delivery of results that meet shareholder expectations."

Jan 1, 2015

Gravity-driven rock falls account for a large proportion of all fatalities and injuries in underground mines. Potentially unstable blocks of rock are found in the hanging wall of excavations, which may be delineated by natural joints or stress fractures. These blocks, referred to as keyblocks, will fail if their weight exceeds the support capacity or if they are located between support units. This paper describes a computer program which simulates blocks in the hanging wall of an excavation based on measured properties of fractures and joints. Keyblocks are identified and placed at random locations in a predefined excavation. The keyblocks are tested against the support to determine whether they fail the support, drop out between the support or are stable. By repeating the procedure several thousand times, statistics of the probability of failure of the keyblocks are obtained. This approach allows the relative hazard associated with different types of support or excavation orientations to be obtained. It is concluded that a probabilistic approach is suitable for the evaluation of supports effectiveness in situations where large numbers of discontinuities or stress fractures are exposed in excavations.

Jan 1, 1998

By A. Kapito

The formation of bainite in steel is dependent on the size of the casting, the heat treatment, and the alloying elements. It is difficult to obtain a fully bainitic microstructure in steels during heat treatment because of its close proximity to the martensite (a?) reaction. The ferrite (a) and pearlite reactions in steels are also rapid and shield the bainite reaction. Alloying elements therefore need to be added to separate the bainite reaction. Boron (B) and molybdenum (Mo) are key elements added to bainitic steels because of their ability to retard the a reaction. Other elements used in the production of bainitic steels are silicon (Si), chromium (Cr), manganese (Mn), and titanium (Ti). In this paper we investigate the effect of alloying elements on the bainite reaction through the use of dilatometry. Dilatometry is a technique that determines phase transformations in the steel and through which continuous cooling transformation (CCT) curves can then be developed. Some initial results are presented of an ongoing study on the development of bainitic steels for railway wheel applications.

Jan 1, 2013

By C. D. K. Gauert

High-pressure waterjet technology is proposed as an alternative tool for selective underground mining of high-grade ore sections in stratiform orebodies showing a preferred ?bottom? or ?top? enrichment such as the Witwatersrand reefs and the Bushveld Complex platiniferous reefs. This technique, utilizing known mining technology together with more advanced machinery and additives as used in industrial and cleaning applications, may lead to an increased life-of-mine (LOM) for mining operations. A series of experiments was successfully carried out in a laboratory on Witwatersrand quartzite material, indicating acceptable cutting performance. Mining volumes by selectively cutting of reef portions are considered to be comparable to traditional drilling and blasting. Economic advantages of waterjet mining include energy savings due to the lower quantity of gangue rock to be hoisted to surface, as well as savings by a decrease in the usage of blasting materials. Capital expenditure of waterjet cutting, if applied on a broad scale, could be lower in the long term than that of conventional drilling and blasting methods. Mining by the application of high-pressure waterjet technology could become a competitive ?green technology? improving the economics and safety of labour-intensive mining operations. This paper suggests that waterjet cutting at an industrial scale can become a routine hard-rock mining technique in the future. Keywords waterjet cutting, high pressure, mechanized narrow reef mining, abrasive agents, costs, selective mining.

Jan 1, 2013

By A. N. Clay

In recent times, there has been criticism of the minerals industry over the lack of quantifiable boundaries between inferred, indicated, and Measured resources. A recent initiative through the United Nations aims to try to converge the mineral resource classification systems. Since the oil and gas industry uses a probabilistic approach to defining reserve boundaries, it is appropriate to introduce a similar statistical methodology for minerals. The Venmyn Variance Tower has been developed based upon traditional statistics to utilize historical and ongoing information in order to quantify variance of geological and chemical parameters and the boundaries and logic for quantitative mineral resource classification. It is proposed that a less than 50% variance from the mean of all sample parameters is required to achieve the classification threshold to define an inferred Resource whereas between 20-10% is needed for an indicated Resource and less than 10% variance from the mean is needed to declare a Measured Resource. These limits are similar to those used by the oil and gas industry, and it is suggested that these thresholds be adopted as an industry standard to ensure consistent quantitative reporting. While this process is intended to use statistics of an orebody to provide quantifiable and defendable boundaries, it cannot be carried out unless the geology of the mineral deposit is understood and the borehole samples can be categorized into appropriate populations for which the statistics are valid. This means that competent geologists are always required to work with and understand the implications of the Variance Tower results. This paper is intended to form the basis of a series of publications that establish a process to take mineral projects along a quantifiable and logical development path. Hence, no specific field example of the practical application of this process is given here.

Jan 1, 2012

By J. A. Bakken, G. Sævarsdóttir, H. Pálsson, M. Þ. Jónsson

The role of the electric arc in the consumption of electrodes in submerged arc furnaces has long been debated. The hostile environment in the furnace does not make direct measurement feasible, so simulation has been used to evaluate the arcs contribution to the erosion. Magnetofluiddynamic (MFD) electric arc simulations and a cathode / anode sub-model developed in order to provide boundary condition to the arc model have been used for this purpose. The cathode / anode sub-model provides current distributions and cathode / anode fall voltages for the arc and temperature distribution for the electrode surface, which is paramount to the erosion rate which in turn is calculated from the Clausius Clapeyron equation and the Hertz Knudsen formula for the vapour transport. In the case of high-current industrial AC arcs, arc currents are typically ~100 kA, phase voltages ~100 V and total furnace power ~10 ? 60 MW. The results show that although enormous amounts of material is evaporated, much of it recondenses on the surface. Furthermore the results show that the arc erosion increases strongly with the arc current. If a single arc is present its contribution to erosion is close to the actual total erosion in the furnace. Results from this analysis indicate that there are possibly more than one arc present in the crater, in which case less than 40% of the total erosion would be due to the arc, the rest is chemical erosion.

Jan 1, 2007

By G. van Aswegen

Seismic monitoring became commonplace in the deep South African gold mines in the early 1990’s. The discipline has, to a large extent, developed beyond the ‘research’ stage, and a ‘Guide to Seismic Monitoring in Mines’ has been accepted by the Department of Minerals and Energy1. Although ongoing research is a requirement for the achievement of all the objectives of seismic monitoring in mines, sufficient knowledge exists to apply seismic monitoring for routine seismic hazard assessment as an aid to risk management. The design and management of seismic monitoring systems can be tested against requirements spelled out in the ‘Guide’. Assuming the seismic monitoring system performs as per requirement, the best practice for routine seismic hazard assessment in mines includes • Long term seismic hazard assessment: through back analysis of seismic data and correlation with numerical modelling output, reasonable tests for planned mine designs are possible. • Medium term seismic hazard assessment: o Spatial analysis through contouring of seismic strain related parameters, with superimposed contours or event plots of stress related parameters allow the delineation of potential instabilities in space. o Quantitative and statistical analyses of seismicity in smaller spatial units (usually encompassing production sites) allow the comparative seismic hazard rating of different areas/sites so that rock engineering input and risk management can be optimised • Short term seismic hazard assessment relies mainly on time history analyses of particular seismicity parameters. The temporal patterns are controlled by a combination of temporal and parameter filters, the optimisation of which determines the success rate.

Jan 1, 2003

By Willem C. A. van Niekerk, David A. Baldwin, Nardus Potgieter, Willie A. Gericke

Authorities that regulate environmental issues pertaining to industrial wastes in South Africa regard landfill disposal as the only effective environmental management option for slag and other inorganic by-products from the ferro-alloy industry. Metallurgical slags are widely utilised in civil engineering and construction applications in other countries in the world and in line with the overall philosophy of conserving mineral and other natural resources, these materials should be assessed for the possibility of resource recovery, recycling, reclamation, direct re-use or alternative uses. This presentation describes a risk-based approach for the assessment of by-products from the ferro-alloy industry for alternative use. Once a by-product from an industrial process has been identified for alternative use, its intended use would be defined, but it will not be possible to control its actual use or misuse in society, nor will it be possible to control its fate during the application life cycle. In the interest of protection of human health and the environment, potential risks associated with the handling and uses of a material throughout its life cycle therefore have to be quantified. The assessment has to include both human health and ecological risks and must cover the entire life cycle of a product, from its production up to its end-of-life disposal. The presentation introduces the concept of tiered risk assessment and demonstrates how this applies in the overall assessment of by-products from metallurgical industry sector for safe use in society.

Jan 1, 2007

By J. H. Van Reenen, H. Thiele, C. Bergman

For some time spirals have been the process equipment chosen to recover metal in the size range 0.15 to 3mm from ferrochrome and silico/ferro manganese slags. Recoveries of metal obtained using spirals are usually about 70%. Spirals are also difficult to control. By combining a novel gate on the Apic pneumatic fines jig with the recently developed Apic classifier, metal recoveries of 76% and grades of over 90% have been obtained for FeCr and SiMn slags in the size range 0.15 to 3 mm. The paper compares classifier operating performance and costs with those spirals for FeCr and SiMn metal recovery from slags. The classifier technology can also be applied to chromite and iron ores and coal fines.

Jan 1, 2004

By I. A. Mwamba

Plain and alloyed titanium aluminides of composition Ti-47.5 at.% Al were prepared by melting commercial-purity titanium and aluminium with additions of 1 at.% precious metal. The as-cast alloys were subjected to potentiodynamic scans in 5, 15, and 25 wt% HCl aqueous solutions at room temperature and compared for their abilities to spontaneously passivate. Addition of precious metals resulted in a general improvement of corrosion resistance by increasing the open circuit potential to more noble values. Addition of 1 at.% gold or silver to titanium aluminide did not significantly increase the corrosion potential (Ecorr) above that of the plain titanium aluminide alloy, indicating that gold and silver are not sufficient cathodic modifiers to improve the corrosion resistance of titanium aluminide in all the solutions tested. However, platinum, palladium, and iridium additions shifted the corrosion potentials to the position of the passive region of plain TiAl for all solution concentrations. This indicated that TiAl alloyed with these platinum group metals would passivate spontaneously by cathodic modification. TiAl alloyed with palladium performed the best in 5 wt% HCl solution with the most positive corrosion potential. In 15 wt% HCl solution, alloys with platinum exhibited the most positive corrosion potentials, while alloying with iridium or palladium revealed more negative corrosion potentials. Thus, palladium alloying led to the best cathodic modification of titanium aluminide in low-concentration HCl solution, whereas platinum and iridium alloying additions resulted in the best cathodic modification of titanium aluminide in high-concentration HCl solutions.

Jan 1, 2013

By M. Stephton, L. A. Cornish, R. Süss, N. B. Maledi, J. H. Potgieter, L. Chown

In today?s gas turbines, the emphasis is on saving energy and reducing the amounts of pollutants emitted. This can be attained only by designing alloys with higher melting points and the capability to retain mechanical integrity at increased temperatures. The development of nickel-based superalloys (NBSAs) has reached its limit, as the alloys are operating at critical temperatures close to their melting points. Further increase in the operating temperatures will result in dissolution of the strengthening phases and even melting. Recent trends are towards developing materials that are adequately strong but have much higher melting points and corrosion resistance than the NBSAs that are currently in use. Studies conducted on Pt alloys with similar structure to the NBSAs have presented mechanical results that are promising. This has led to further development of these alloys as a replacement for NBSAs. The operations of gas turbines are usually limited by hot corrosion, which could lead to catastrophic failures. Increased temperatures have an adverse effect on the corrosion of the alloys by making the environment more aggressive. Hence, during a material selection process, the corrosion behaviour of any selected material for a highly specialized application such as gas turbines needs to be assessed. Generally, coatings are applied to combat degradation by salt deposits, hence coated and uncoated NBSAs were selected as benchmark alloys. Corrosion mechanisms and kinetic studies of the Pt alloys were conducted. High temperature hot corrosion (HTHC) tests were conducted at 950°C for540 hours. Analysis of the corrosion products was conducted using a Raman spectrometer, scanning electron microscope with energy dispersive X-ray spectroscopy (EDS) optical microscopy, and X-ray diffraction study of the phases that formed. Both coated and uncoated NBSAs failed under the test conditions. Samples were covered with a porous non-adherent greenish layer which is characteristic of NiO. Pt alloys displayed superior corrosion properties compared with the benchmark alloys.

Jan 1, 2006

By Donald Leroux, Simon Gariépy, Luc Lachance

"Quantitative information about the quality of metal balance results is often overlooked when making important plant production planning decisions. Not only is this common omission made in a context where many measurements taken in and around mineral processing plants carry significant errors, but it also conflicts with the AMIRA P754 Code of Practice for Metal Accounting. The fact that metal balances are typically published without any indication of data quality may give the wrong impression that the measurements are unquestionably accurate. While it is true that statistical data reconciliation can improve the confidence intervals of redundant variables, there is no data processing technique that brings them down to zero at a finite cost. In this paper, we review the entire data flow, starting from field instruments to metal accounting-based decision-making to show how measurement errors are transmuted into business risks associated with production planning. Necessary conditions for first exposing then quantifying such business risks are stated. Pitfalls to be avoided are also discussed. Finally, a simplified risk assessment and management procedure which considers the quality of metal balance results are applied to a polymetallic mineral processing plant. INTRODUCTION Each and every mineral processing plant has production reporting obligations. In this paper, we are concerned with metal accounting reports (Morrison, 2008) where saleable metal flows and inventories are estimated and published. These metal accounting reports are delivered to a variety of stakeholders who use them for internal management purposes (day-to-day plant production planning, plant operation optimisation, capital spending, etc.) as well as for external management (royalty settlements, tolling agreements, etc.). Hence, there should be no doubt that spotless metal accounting is instrumental to high-quality corporate governance (Gaylard et al., 2014) of mining and metallurgical companies. To this extent, one would have expected industry-endorsed standards to have emerged a long time ago. However, the lack of an accepted set of standard procedures for metallurgical accounting was explicitly recognized as an industry-wide problem only in August 2001 during an SAIMM workshop held in Cape Town, South Africa. Discussions that followed this workshop led to the initiation of the AMIRA Project P754, “Metal Accounting and Reconciliation”, in 2003."

Jan 1, 2015

By B. Larsen, S. Z. Nascimento, K. Fidje, J. P. M. Amaro, H. Gran

Safe and good operation of Søderberg electrodes is dependent upon high quality electrode paste coupled with correct electrode operating procedures. Good electrode performance depends further on proper melting and densification of the electrode paste. The melted paste should form a dense and viscous layer that prevents gasses from the baking process to move upwards. Both paste cylinders/blocks and briquettes can be used, but the procedures may differ between the various types of paste products. For briquette columns the formation of the important viscous layer is obtained through melting and densification of the briquettes. By basic rheological studies of electrode paste and by laboratory tests of briquette beds at isothermal conditions we have achieved a better understanding of the melting process. The effects of temperature gradients, pressure and friction between the briquettes and the electrode casing have also been evaluated qualitatively in pilot scale experiment and in industrial scale tests. The paper shows that melting and densification starts at a considerable lower temperature than the pitch softening temperature. It is concluded that the formation of a briquette electrode column depends on parameters as temperature, briquette column pressure and the friction. Operating conditions influencing the above parameters should be defined and established for each specific furnace operation. Such factors are e.g., charging and slipping procedures, column heating and electrical conditions.

Jan 1, 2004

By F. S. A. de Frey

The author would like to refer to his contribution to the paper `Design of pillar systems in South Africa' by Ozbay et al. 1. The authors agreed `wholeheartedly that further research, together with carefully planned field trials, in pursuit of this potentially highly rewarding concept' of the small span small pillar method is warranted. On 30 September 2010 the author went underground at the Kroondal Chrome Mine to observe how the concept of smaller spans was being applied. He was pleasantly surprised to find that the typical coal mine bord and pillar sytem was being used very successfully. Although the deepest mining was taking place at a depth of only 450 metres, Kroondal would be an ideal mine to do further research together with carefully planned field trials. At Crown Mines Gold Mine, where the author worked, he was informed that the first recorded rockburst took place at a depth of 635 metres below surface. The depth of the platinum and chrome mines is increasing, with the risk of an excalation in injuries and fatalities due to 'backbreaks' and siesmic activity. The rock engineer at Kroondal was not aware of backbreaks occuring on the mine. It is important that the rock engineers of the base mineral and gold mines get together and give more serious attention to the host rock environment in which the pillars are situated.

Jan 1, 2011

By M. Hooman, W. M. Marx, R. C. W. Webber-Youngman

This paper discusses a study that investigated different underground bulk air heat exchanger (>100 m3/s) design criteria. A literature review found that no single document exists covering all design criteria for different heat exchangers, and therefore the need was identified to generate a guideline with decision analyser steps to arrive at a technical specification. The study investigated the factors influencing heat exchanger designs (spray chambers, towers, and indirect-contact heat exchangers) and the technical requirements for each. The decision analysers can be used to generate optimized, user-friendly fit-for-purpose designs for bulk air heat exchangers (air cooler and heat rejection). The study was tested against a constructed air cooler and heat rejection unit at a copper mine1. It was concluded that the decision analysers were used successfully. This tool (decision analysers) can be used by engineers for the efficient and cost-effectively design of heat exchangers.

Jan 1, 2015