Search Documents

By J-C. Lv, S. Zhao, F-L. Zhang, T. Yan

"To eliminate nozzle clogging during continuous casting of ship plate steel and reduce the calcium addition required, the composition of CaO-MgOAl2O3 inclusions in the liquid phase region must be controlled. Thermodynamic calculations using FactSage show that when the balanced Al content is 0.03 mass %, aCa in the liquid steel is 1–10 ppm, and aMg is 0.01–0.3 ppm; and when the balanced Al content is 0.06 mass %, aCa in the liquid steel is 1–30 ppm, and aMg is 0.05–0.9 ppm. The CaO-Al2O3-CaS inclusions can be controlled in the liquid region below 1600°C at aCa values of 5 ppm, 15 ppm, and 30 ppm, and the balanced Al content should be controlled in the range of 0.001–0.050, 0.005–0.250, and 0.010–0.50 mass %, respectively. Based on theoretical analysis, the refining slag composition should be controlled to 45–53 mass % CaO, 30–37 mass % Al2O3, 6–12 mass % SiO2, and 6–8 mass % MgO. Optimization of the slag system and steel composition can reduce, or even eliminate, the requirement for calcium treatment. The total oxygen content in the slab can be controlled to 15–21 ppm, with typical micro-inclusions ??10 ??m in size, with compositions in the CaO-Al2O3-MgO and CaO-Al2O3-CaS systems. Introduction With the rapid growth in steel output in China and the changes in the macroeconomic environment, competition in the steel industry has become more intense. The technology for economical cleaning of high-grade steel is important for improving product quality and reducing production costs. However, the functions of refining equipment have not been fully taken into consideration, and the combination of refining methods has not been optimized completely. These problems have become a bottleneck, restricting modern steel enterprises from developing an economic clean steel production process. Ship plate steel produced by the converter long process has been selected as the example in this study. The composition of the steel is shown in Table I. This steel is a high-strength low-alloy steel for rolling media and heavy plates, mainly used for ocean-going vessels and other steel structures. The carbon content in the steel is far from the peritectic point, and the crack sensitivity of the slab surface is weak, so impurities and gas content are strictly limited. Therefore, the process route BOF (basic oxygen furnace) – LF (ladle furnace) – CC (continuous casting) needs to be studied."

Jan 1, 2018

By B. Orgilbayar, B. Unursaikhan, S. Sukhbat, Ts. Zagarzusem, D. Baasanjav, L. Jargalsaikhan, E. Otgonjargal, N. Sugir-Erdene, Ts. Soyolmaa

This study has investigated the efficacy of the gravity beneficiation method based on gravitation and centrifugal forces for manganese ore. Powdered samples of manganese ores from the Unagad deposit in Mongolia were analysed for their element and mineralogical composition using ICP-MS and X-ray powder diffraction (XRD). The analysis presented the mineralogical compositions of the ores as hydro goethite, manganese minerals and magnetite, gangue minerals as quartz, albite, orthoclase and microcline of manganese ore. Manganese minerals are white in colour and have micro-veinlet, fine grained-aggregates associated with gangue minerals. The most important manganese minerals are hausmannite, pyrolusite, rhodochrosite, and manganosite. The composite of feed containing 17.31 % Mn and 36.3 % SiO2 was processed in a shaking table. In the experiment, a concentrate assaying 41.37% Mn was obtained from this composite with 65% recovery. In another experiment, f80=0.074 mm particle size ore was used in the MGS concentration test. A concentrate containing 38.34 % Mn with 75.2% recovery was produced in this experiment. The results showed that it is possible to obtain concentrate through gravity processing of manganese ore, which is an economically beneficial process for producing a product of a standard requirement. Keywords: Manganese ore, gravity separator, centrifuge, shaking table 1. Introduction

Jan 1, 2020

By N. Tatalias, P. Ilunga, M. Lampi, J. Edwards, K. Valkama, M. Nicolle, D. Samal

"Developing a greenfield mining project is a complex exercise: doing so in an increasingly volatile, uncertain, and ambiguous global economy adds significantly to this complexity. In the context of an elevated cobalt price, this paper outlines the metallurgical and process development of the Mutoshi copper–cobalt project for copper cathode and cobalt hydroxide production in the Democratic Republic of Congo. Chemaf has a long production history on the Copperbelt, a region widely perceived to be tough to operate in. This history stretches back to 2001, during which time the company has developed two copper–cobalt processing facilities. The experience gained in the development and operation of these two facilities has been used extensively in the Mutoshi copper–cobalt project. The metallurgical test work, process design, and project delivery approach are presented. Additionally, the decisions taken to minimize risk and maximize upside to the project are discussed. IntroductionChemaf (Chemicals of Africa), a mining company located in Katanga province of the Democratic Republic of Congo (DRC), has been operating since 2001 with two major copper– cobalt processing facilities: the Usoke and Etoile plants. In 2016, Chemaf acquired the Mutoshi mine, which belonged to Gecamines and had been explored by Anvil Mining since 2004 under a joint venture with Gecamines. Chemaf appointed African Mining Consultants Ltd (AMC) to undertake a preliminary economical assessment, then develop a JORCcompliant Mineral Resource estimate and finally a full life-of mine feasibility study. Both a Mineral Reserve and Mineral Resource were developed and the final life-of-mine feasibility study is to be published shortly. A metallurgical test work programme was initiated and carried out by Chemaf’s research and development laboratory with assistance from the Chemaf process team. After completion of the initial test work, Chemaf developed a process design criteria document for a 20 kt/a copper cathode and 8 kt/a cobalt in hydroxide production plant, followed by a flow sheet and supporting METSIM mass balance. As the drilling progressed, the plant design capacity was revised to 16 kt/a cobalt production. The life of the mine at this production rate is over 40 years."

Nov 1, 2018

By J. Levin

Bond's Standard Work Index (SWi) indicates the grindability of an ore, and his Operating Work Index (OWI) indicates the performance of a grinding mil or circuit. The comparison of the two indices offers a measure of the efficiency of the grinding operation. Mil (or circuit) performance, particularly on the Witwatersrand, is often indicated by the index kilowatt -hours per tonne of minus 75 µm material produced (kWh/t minus 75µm or OE75)' The paper shows that a standard kWh/t minus 75 µm index (SE75) can be obtained from the standard Bond grindability test (which provides the SWi), and asks whether the two E75 indices can be used in the various ways in which the two Work Indices are used. For the answer, the paper presents averaged values for the standard grindability indices of the gold ores of the Witwatersrand, averaged values for the performance of grinding mils operating on those ores, and the results of laboratory grinding tests on a composite of several Witwatersrand ores. The particle-size indicator for the calculation of the Wi indices, the am size, is constant in its relation to the largest particles present, whereas the percentage minus 75 µm, the indicator of size for the E75 index, varies with the degree of grinding in its relation to the size of the largest particles. Because of this difference, the standard Work Index increases as the grind becomes finer, whereas the standard kWh/t minus 75 µ value decreases. The Wi and E75 indices nevertheless serve similar purposes when applied to moderately fine grinding-finer than 70 per cent minus 75 µm. Open circuit laboratory grinding tests revealed three stages in the grinding process, and credible values for the open circuit Work Index were obtained only from the second stage. The conversion of the open circuit Work Indices to the equivalent of close circuit indices by the application of Bonds open circuit inefficiency factor (a constant for grinds indicated by the d80 size) was of limited success; however, the development of a conversion factor related to particle-size should not be difficult. Initially difficulty was experienced in the calculation of the 0E75 indices from the results of the laboratory tests, but it was eventually considered that a constant value of the index derived from the results would be close to the true open-circuit index. The open-circuit grinding test could there fore be a convenient method for the detection of differences in the grindability of ores.

Jan 1, 1992

By H. A. D. Kirsten

Mining-induced seismicity is usually evaluated in terms of continuum elastic analyses, and is quantified in terms of energy release rate as state parameter and excess shear stress along particular features on which failure may be induced. Although both of these quantities are representative measures of potential seismic activity, elastic analyses do not enable the associated stresses and displacements in the rock in which failure occurs to be evaluated reliably. The paper compares the effect of depth, span, support stf1Jhess, field stress ratio, and discontinuity strength on mining induced seismicity determined from elastic analyses and from analyses in which discontinuities in the rock are allowed to fall. It is, accordingly, shown that the incidence and magnitudes of potential seismic events and the net excess shear as representative state parameter cannot be determined reliably from elastic analyses that do not account for the failure of ubiquitous discontinuities. The magnitudes of seismic events in rock in which ubiquitous discontinuities are allowed to fail are very considerably overestimated in elastic analyses. The extent of the seismic source region and the associated seismicity do not increase with depth, which, together with the improved containment of the concomitant rockburst damage by backfill is reassuring for mining at greater depth in future. For conventional support, the magnitude of potential seismicity increases for an increase in span in elastic rock, but remains unaffected in non-elastic rock. For backfill, the magnitude of potential sesmicity decreases substantially in elastic and non-elastic rock for an increase in span. Increases infield stress ratio very significantly reduce potential seismicity irrespective if the type if analysis, but effect the distribution if potential seismic events very differently in elastic and non-elastic rock.

Jan 1, 1994

By N. Coulson, P. Ledwaba

"The University of the Witwatersrand presents an accredited four-course training programme for community relations practitioners (CRPs). Between May 2013 and October 2014 six courses were facilitated for 145 participants, of whom 82% were from sub-Saharan Africa, 62% worked in mining, and 58% worked directly with communities. Thematic analysis of the comments of course participants collected during course exercises found that there were a set of coherent drivers for resilient companycommunity relationships, but that the restrainers to resilient relationships were often context-specific and dominated by politics. CRPs reported facing as many difficulties in the internal company environment as in the external environment. These findings for CRPs in Africa resonate with those worldwide.InroductionMuch has changed in how the extractive industry responds to social and community issues. There has been a growing prioritization of community-related issues within the extractive industry globally (Kemp, 2010; Tatar, n.d.). According to Kemp (2010) this can be attributed partly to escalating pressure from local-level stakeholders to push mining companies to take greater responsibility for the social, economic, and environmental impacts of mining. Securing and maintaining the social licence to operate is ranked fourth in terms of the top risks facing the mining and metals industry in 2016, up one place from 2015 (Ernst & Young, 2016).Conflicts between local communities and large-scale mining companies arise because of the social, environmental, and economic impacts of mining. Worldwide, large-scale mining companies have a poor reputation amongst communities, including those in Africa (Gilberthorpe and Banks, 2012; Kemp and Owen, 2013a; van Wyk, n.d.). For mining companies, conflicts for whatever reason, result in loss of productivity, lost opportunities, lost time, and adverse impacts on reputation (International Council on Mining and Metals, 2015). Conflicts also have a significant financial impact on mining operations (Franks et al., 2014). Davis and Franks (2014), estimated that US$10 000–50 000 is lost each day when a project is delayed during the exploration phase, and about US$20 million per week when in operation. Today these costs could be expected to be higher due to increasing input costs."

Jan 1, 2017

By Y. P. Shoupletsov

ABSTRACT. A retrospective analysis of some geomechanical classifications for rock masses is presented. It is shown that estimates of rock mass strength according to geomechanical classifications developed, e.g., for construction of tunnels and for ore mines can differ very much. Development of specifically oriented classifications for rock masses with certain geomechanical properties is required. ZUSAMMENFASSUNG. Es wurde eine retrospektive Analyse einiger geomechanoschen Klassifikationen von Gesteinsmassiven durchgefuhrt. Es idt aufgezeigt worden, dass die Bes-timmung der Festigkeit des Massivs nach geomechanischen Klassifikationen, die z.B. fur den Bau von Tunnelen und fur Erzbergwerke entwickelt wurden, sich um etliche Male unterscheiden kann. Es ist eine Entwicklung von spezialisierten Klassifikationen fur Gesteinsmassive mit bestimmten geomechanischen Eigenschaften erforderlich. RESUME. Il a ete fait l’analyse retrospective de certaines classifications geomecaniques des massifs de roche. Il a ete montre que les estimations de solidite du massif suivant les classifications geomecaniques etudiees, par exemple, pour la construction des tunnels et pour les puits de minerai peuvent differer en quelques fois. Il est donc necessaire d’etudier les classifications specialisees pour les massifs aux proprietes geomecaniques particulieres.

Jan 1, 2003

By Ralph H. Nafziger

This paper reviews the major deposits of lower-grade chromite in the world, and a wide variety of methods used for the recovery of chromium from them. Gangue materials in more coarsely sized ores can be separated by gravity means, whereas flotation techniques are required for finer-grained materials. However, unless there is considerable Iron In the ores, physical means cannot increase the Cr/Fe ratios. Chemical techniques such as hydrometallurgical methods, chlorination, roasting and leaching, and smelting are required for this purpose. A greater understanding of the physical properties of chromites and the chemical reactions that take place in the recovery operations is required before. the recoveries from lower-grade chromites can be maximized. More efficient recovery operations can be realized If It can be shown definitively that the reduction of chromites occurs via either a gas-solld or solid-solid mechanism, for example. The effects of specific impurities on the chromite reduction reactions need to be better understood, as do reagent and pH control in the flotation of chromite.

Jan 1, 1982

By P. Sebola, S. Rasmeni, K. Seripe, D. Chetty

"South Africa’s Northern Cape Province hosts semi-precious and gemstone occurrences that are sporadically mined on a small scale by local communities. Tiger’s eye, a gemstone known for its chatoyancy properties, is found in important deposits located near the town of Prieska, where is it intermittently mined. Challenges faced by small-scale and informal mining include mining without proper permits, risky mining practice in dangerous terrain, and illegal export of raw material without concerted effort at domestic beneficiation. As part of a study aimed at job creation and social upliftment in the region, tiger’s eye deposits in the Prieska area were assessed to assist small-scale miners to understand tiger’s eye grades and their distribution. This will allow not only more efficient and safer mining of these deposits, but also beneficiation of the raw product into tumbled stones, cabochons, jewellery, and other small artefacts for sale. A hub established in Prieska by Mintek trains locals in the beneficiation of tiger’s eye. Supply to the hub must make use of a consistent grading system, which is discussed in this paper. Together with proper mine licensing, such an approach will develop mining and beneficiation skills, and create and sustain employment for the local community. IntroductionTiger’s eye is a semi-precious stone known for its chatoyancy property, which is caused by parallel, silicified asbestos fibres that impart a silky lustre to specimens. Deposits of tiger’s eye in the surrounds of the town of Prieska, Northern Cape Province, formed the focus of a study aimed at small-scale mining and beneficiation of this commodity. The Prieska tiger’s eye deposits are located along the N10 route to Upington (Figure 1). Tiger’s eye is unevenly distributed and occurs as lenses of various sizes, interbedded in gently folded metasedimentary rocks of mostly banded iron formation (BIF). The tiger’s eye occurrence in the Northern Cape Province, especially in the Prieska area, has not been extensively researched. There is thus limited information available in the public domain. The lack of knowledge on tiger’s eye distribution has resulted in local small-scale miners adopting a trial-and-error method of mining. Basic geological mapping and field evaluation of the deposit, coupled with professional judgement, are important aspects of any small-scale mining operation and can contribute significantly to the formulation of various acceptable and equally viable mining methods and practices."

Jan 1, 2016

By R. W. O. Kersten

This paper describes the method used at Agnes Gold Mine in the calculation of pillar strengths, which involves a back-analysis type of approach. The results obtained there are comparable with those obtained by accepted formulae for pillar strength. It was found that a stress level of 70 MPa for the width of combined pillars (Le. crown and sill pillars) causes failure of the reef drives as well as the tops and bottoms of the stope side walls. As shrinkage stoping to depths of more than 650 m would result in very low percentage extractions, alternative methods of stoping will have to be investigated for these depths.

Jan 1, 1984

By J Taguta, B. McFadzean, P. E. Ngoepe, M. G. Mulaudzi

Computational modelling methods and isothermal titration calorimetry (ITC) were employed to investigate the interaction of a pyrite surface with thiol collectors. Modelling work was conducted in the presence and absence of water. Microcalorimetry was employed to investigate the resultant energy of interaction pyrite as a result of mineral-collector interactions. Sodium ethyl xanthate (SEX), diethyldithiocarbamate (DTC) and diethyl dithiophosphate (DTP) were investigated in this study. The results showed that the calculated surface energies and morphologies for FeS2 showed that (100) and (111) are the most stable surfaces. The morphology also indicated the appearance of the (100) and (111) surface facets and no presence of others. The calculated adsorption energies between thiol collectors and the pyrite surface were always more exothermic than the experimentally determined ones. When comparing different ligand types with the same alkyl chain length, the heat of adsorption of diethyl-DTC was greater than that of ethyl xanthate and diethyl-DTP for pyrite. Experimentally, the diethyl DTP barely adsorbed onto the pyrite surface and this may be due to a different mechanism of action. In computational calculations, water adsorption was found to reduce the reactivity of the Fe atom for the interaction with thiol collectors, and bring the adsorption energies closer to the magnitude of the experimental values. Keywords: Computational modelling, microcalorimetry, experimental and thiol collectors, adsorption energies

Jan 1, 2020

By C. A. Young, J. L. Bowden

"Cyclic voltammetry experiments were conducted on copper and chalcopyrite (CuFeS2) in the absence and presence of ethyl xanthate, and compared to mass-balanced EH–pH diagrams. The results for copper duplicate those found in the literature and confirm xanthate chemisorption. However, the, results indicate that chalcopyrite oxidizes to chalcocite (Cu2S) and only afterwards is chemisorption observed due to small currents appearing with xanthate. This phenomenon suggests that the mineral's hydrophobicity is induced by more than dixanthogen and copper xanthate. Hydrophobicity was found to be pH-dependent over a range of alkaline conditions (pH 7–11) at narrow potentials (0 to –200 mV). An EH–pH diagram for chalcopyrite with xanthate is presented to illustrate the conditions under which chalcopyrite would be hydrophobic and thereby more thoroughly explain the results in the literature. IntroductionSulphide minerals are generally concentrated from ores by froth flotation, a physiochemical process that induces separation based on differences in hydrophobicity. In this process, a gas is bubbled into a slurry and the minerals that are hydrophobic (water-repelling) adhere to the bubbles and float to the surface while the hydrophilic (water-loving) minerals remain in the slurry. With sulphide minerals, the hydrophobicity is generally established in two ways. The first is by the addition of a collector, which is a heteropolar molecule with a reactive inorganic head group and an inert organic tail. Typically, the head group bonds with the sulphide mineral surface by adsorbtion either chemically (chemisorption) or physically (physisorption) or by complexing with atoms that solubilize somewhat at the surface (surface precipitation). These interactions leave the organic tail protruding from the mineral surface, thereby inducing hydrophobicity. The second method is by oxidation of the mineral surface to form a layer that is metal-deficient/sulphide-rich or comprised of elemental sulphur. Because the layer mimics naturally hydrophobic sulphur, this enables ‘collectorless’ flotation. Furthermore, this oxidation phenomenon adds an electrochemical dimension to the understanding of sulphide mineral flotation."

Jan 1, 2016

By R. J. Gordon, N. J. Keys, N. F. Peverett

Photometric sorting of ore on a South African gold mine by N. J. KEYS. B.E. Met. (Queensland) (Visitor). R. J. GORDON. (Visitor). And N. F. PEVERETT. B.Sc. (Eng.) (Wits) (Fellow) This paper concerns the development and application of a high-throughput, multi-stream photometric sorting machine developed for the South African gold mines. It is now believed that this sorter and its progeny may be found suitable for a large proportion of all possible sorting applications. A laser-light source and sensitive photomultiplier are employed in a scanning system to detect light reflected from the surfaces of rocks passing through the sorting zone. Electronic circuitry then analyses the photomultiplier signal, which represents the varying intensity of the reflected light, and produces control signals to actuate the appropriate valves of an array of air-blast rejection devices to remove from the feed certain particles selected by the analysing process. Typical throughput per machine ranges from 50 t/h for a minus 60mm plus 30mm feed to 200 t/h for minus 150mm plus 70mm material.

Jan 9, 1974

By J. Petersen, H. Naderi, H. Zare, M. H. Nikzad, M. Karimi

In the copper electrorefining process, the dissolution of anodes is significantly reduced or even stopped when the passivation phenomenon occurs. The results of this phenomenon are increasing energy consumption, residual formatting, and voltage levels in the cell. In this study, the electrochemical behaviour of blister copper in the presence of sodium persulfate (PDS) was studied. The electrochemical methods of LPR, Tafel, and Electrochemical Impedance Spectroscopy (EIS) were used. The results showed that the addition of sodium persulfate activates the electrode surface and increases the open circuit potential. In the presence of PDS, the polarisation resistance of the electrode shows an increasing or decreasing tendency, based on the PDS concentration. This tendency is probably due to the formation of surface layers (such as slime layer or copper sulfate) and dissolution of this layer at various concentrations of PDS. The lowest polarisation resistance of 1.8 ohms and the highest corrosion current of 60.6×10-3 and 36.6×10-3 A/cm2 from LPR and Tafel techniques respectively were obtained at the concentration of 40 g/l PDS. Based on the results of potentiodynamic and electrochemical impedance spectroscopy tests, the addition of sodium persulfate to the solution reduces the corrosion resistance, therefore the passivation time of the blister copper anode increases. Keywords: Blister copper, electrorefining, sodium persulfate, anodic passivation

Jan 1, 2020

Proceedings of the Ninth International Symposium on Techniques for Decision-Making in the Mineral Industry, Montreal, June 1970. The Ninth International Symposium on Techniques for Decision-Making in the Mineral Industry was sponsored by The Canadian Institute of Mining and Metallurgy, McGill University and Ecole Poly technique. The programme included 71 papers on various topics, as follows: Market Analysis and Logistics Planning; Quantification of Geological Variables; Blending; Capital Investment Decisions; Mining; Financial and Economic Analysis; Search for Mineral Deposits; Market Forecasting and Strategies; Operations Research in Process Modelling; Ore Reserve Estimation; Management Information Systems; Optimization and Control of Mineral Processes. In addition to general sessions, a special feature of the Symposium was Executives' Day, which was held to provide top and middle management with a broad understanding of the usefulness of decision-making techniques and their role in the mining organization. Panel Discussions and two keynote speakers provided a review, in non-technical terms, of the areas in which decision-making techniques have proven valuable. The present volume contains 65 papers submitted for publication, along with a complete account of the Executives' Day discussion. It is broadly divided according to the above subject headings. Approximately 550 pages, illustrated. Price: $15.00; $12.00 to students, plus 50 cents for handling costs. Order now from CIM headquarters: Canadian Institute of Mining and Metallurgy, 906-1117 Ste. Catherine St. W. Montreal 110, Quebec.

By L. A. Vermeulen, D. D. Howat

The use of pebbles as the medium in the grinding of quartz gravel in a laboratory mil provided experimental data that were used to quantify the relationships between the feed rate of ore to the mil, the fineness of grind of the product, and the wear rate and consumption of the grinding medium. Fineness of grind is expressed as the inverse of the harmonic mean size, a quantity that is calculated from data obtained by sieve analyses. The commonly used criterion for fineness of grind (the percentage of material smaller than 75 µm in the mil product) is shown to corelate approximately linearly with the inverse of the harmonic mean size. An increase in the feed rate was found to cause the harmonic mean size of the product to increase linearly, Le. the relationship previously found for metalic grinding media is applicable to al grinding media, irespective of shape or composition. Simple expressions for the consumption and wear rate of pebbles are derived from the experimental data, and are shown to be functions of the feed rate. The expression for wear rate is a monotonicaly increasing function, while that for consumption is a hyperbolicaly decreasing function of the feed rate. In contrast, a linear relationship was found between the rate of wear of the grinding medium and the rate production of fines. The expressions that were previously developed in relation to the use of metalic grinding media are shown to be equally applicable to pebble milling.

Jan 1, 1988

By L. Cong, C. Liu, N. Zhang, W. Cao, C. Zhou, X. Fan

"The modes of occurrence of arsenic and the effects of low-intensity leaching-flotation on arsenic removal from coal slime from the Tanggongta Plant, Inner Mongolia, China were investigated. The coal slime was examined using hydride generation inductively coupled plasma optical emission spectrometry and X-ray diffraction to obtain the content of elements and the major minerals. The modes of occurrence of arsenic in minerals were determined using selective leaching, float-and-sink analysis, and polarized light microscopy. The results indicate that pyrite is the dominant carrier of arsenic in the coal slime, which predominantly exists in association with clay. Significant proportion of the arsenic is removed by a low-intensity leaching-flotation process, consistent with the data from selective leaching and flotation of gangue. The results show that low intensity leaching-alkali washing-flotation is more efficient than direct flotation and low-intensity leaching-flotation.IntroductionUnderstanding the occurrence of arsenic in coal and its removal is significant in optimizing coal utilization, because arsenic in the environment is viewed as a potentially toxic trace element (Finkelman, Belkin, and Zhang, 1999; Hall, 2002; Smith et al., 1992; Smedley et al., 2003; Zheng et al., 1999). Many studies on the modes of occurrence and concentration trends of arsenic in different coal and washing products have been performed (Diehl, Goldhaber, and Hatch, 2004; Kolker et al., 2000; Quick and Irons, 2002; Wang et al., 2006; Fan et al., 2016). Trace elements are usually preferentially associated with certain minerals and the form that these minerals take will influence the efficiency of removal during cleaning (Quick and Irons, 2002). Arsenic is mainly associated with minerals such as pyrite, carbonate, and silicate (Demir et al., 1998; Diehl, Goldhaber, and Hatch, 2004; Zhou et al., 2014). The existence of organically bound arsenic was also confirmed using X-ray absorption (Kolker et al., 2000). However, inorganic arsenic is the principal source of pollution because of its leachability and high concentration compared with organic arsenic (Fujino et al., 2004; Gao, Lu, and Wang, 2010; Jiang et al., 2008; Kolker et al., 2000)."

Jan 1, 2017

By K. Kabezya

A study on slag dispersion in a model of bottom-blown bath smelting converter was undertaken at room temperature. The aim was to investigate the behaviour of the dispersed slag phase at various operating conditions with very high gas flow rates in low slag volume (10%) systems. For simulation purposes water, paraffin-oil, and air were used to represent the bulk steel, molten slag, and gases respectively in a one-fifth cold model of the commercial 100 t Creusot-Loire-Uddeholm (CLU) converter used in the manufacture of stainless steel in South Africa. Dimensional analysis was done to correlate mathematically the dispersed phase holdup with the operating conditions and the modified Froude number. The overall expression of the holdup revealed that the dispersed slag phase decreased with the vertical distance from the original interface between the liquid phases. The dispersed phase also decreased with the radial distance in the water plume zone toward the sidewall. The holdup was apparently much higher on the side of the reactor where there were no tuyeres. The modified Froude number ensured the correlation between the model and the prototype.

Jan 1, 2014

"This study examines the problems faced by open pit mine superintendents who make choices about how to direct their materials, either to the waste dump or to the mill. The paper explores the effects of introducing a 10% sampling error and a 0.9-times to 1.1-times sampling bias on positively skewed distributions for precious and base metals, negatively skewed distributions in the case of bulk commodities, and normal distributions as is the case for coal deposits. Parent distributions for each commodity were created on a 25 x 25 m grid using transformations of gold, iron ore, and coal data-sets, spatially based on a nonconditional Gaussian simulation. Ordinary kriging of grades for the three commodities into a 10 x 10 m grid provided the reference case against which the distributions with the sampling error and sampling bias for the commodities were compared. Imposing cut-off grades on the actual-versus-estimated scatterplots of the three commodities allowed the distributions to be classified into components of waste, dilution, ore, and lost ore. Ordinary kriging of values for each deposit type acted as the reference data-set against which the effects and influence of 10% sampling error and 0.9-times to 1.1-times sampling bias are measured in each deposit type. Indications are that the influence of error and bias is not as significant in gold deposits as it is in iron ore and coal deposits, where the introduction of small amounts of error and bias can severely affect the deposit value.IntroductionThe effects of poor sampling and the financial implications for mining companies, traders in mineral assets, and sellers of metal as dore or commodities is documented in a number of studies, the most notable of which is that by Carasco (2004). He examined the financial impact of poor sampling practices in the Chilean copper industry and found that finacial losses due to poor sampling amounted to hundreds of millions of dollars over the life of a mining operation. Holmes (2004) examined the effects of correct sampling and measurement as the foundations of metallurgical balances, and found that revenues from the sales of large iron ore shipments may be profoundly affected by poor sampling practices. In South Africa the way in which sampling of in situ gold-bearing reefs affects the mine call factor has been an ongoing study since the disparity between the estimation of gold in the reef and the actual gold bullion produced was noted by early investigators such as Beringer (1938), Jackson (1946), Sichel (1947), Harrison (1952), and a number of others."

Jan 1, 2017

By N. Naude, W. P. Roux

Fine particle beneficiation plays an ever-increasing role in mineral processing plants and it seems that technology can’t keep up with the challenges involved in the treating of these fines. The REFLUX™ classifier has proven itself able to treat high tonnages of fine material, especially in the coal industry. There are various fine ore applications that can benefit from such a process, yet laboratory and pilot-scale tests on many of these ores show poor efficiencies and recoveries. A better understanding of the design, operation and mechanisms of the REFLUX™ classifier is required to determine if and how it fits into these applications. The mechanisms in gravity separators are very complex due to the complex hydrodynamics, and the REFLUX™ classifier is no exception. The mechanisms of these systems are usually described through theoretical single particle-models that are hard to verify through analysing the feeds and products of these processes. To verify these models the movement of individual particles must be measured, which is not an easy task. In this paper the separation mechanisms in the incline channels of the REFLUX™ classifier were investigated with high-speed videography. A small lab scale model of the incline channel was constructed for this purpose. It was possible to capture and track the trajectories of particles under certain conditions and match these trajectories with theoretical models. The resuspension of particles, clustering and streaking was also observed and captured. Keywords: REFLUX™ classifier, particle trajectory, beneficiation, high-speed videography

Jan 1, 2020