Search Documents

By T. Aoki, Y. Maeno, R. Kawano, F. Nakahara, Y. Obara, K. Shibata

The mechanical behaviors of fully-grouted long-embedded cablebolts actually used in situ are very non-linear in pull tests and are different from those of short-embedded cablebolts. We have conducted the pull tests of long-embedded cablebolts installed in mockup rock test blocks, which are 4m in the longitudinal length. In order to investigate the mechanical behaviors inside the test block, the axial load distribution along the cablebolt and locations of acoustic emission events were measured during each pull test. It was found that the axial force distributions were quite linear and that the gradients were interpreted as the grout bond strength by taking into consideration the stress balance at the infinitesimal segment of a cablebolt. Les boulons-câbles longs entièrement cimentés qui sont réellement utilisés sur place présentent, au cours des essais de traction, des comportements mécaniques considérablement non linéaires et différents de ceux des boulons-câbles courts. Nous avons mené des essais de traction des boulons-câbles longs installés dans une maquette de fond rocheux servant d’éprouvette d’une longueur longitudinale de 4 m. Afin d’étudier les comportements mécaniques intérieurs de l’éprouvette, la répartition de la force axiale du boulon-câble et l’émission acoustique ont été mesurées durant chaque essai de traction. Il s’est avéré que les répartitions de la force axiale sont sensiblement linéaires et que leurs gradients représentent la résistance d’adhésion en prenant en compte l’équilibre de contraintes à la partie infinitésimale d’un boulon-câble. Das mechanische Verhalten von ganz eingegossenen, lang eingebetteten Kabelbolzen, die vor Ort eingesetzt werden, ist bei Zugprüfungen sehr nichtlinear und anders als das von kurz eingebetteten Kabelbolzen. Es wurden Zugprüfungen mit lang eingebetteten Kabelbolzen durchgeführt, die in Prüfblöcken (Gesteinsattrappen) mit 4 m Länge eingelassen waren. Zur Untersuchung des mechanischen Verhaltens in den Prüfblöcken wurden die Axiallastverteilung entlang des Kabelbolzens sowie das Auftreten von Schallemission im Verlauf jeder Zugprüfung gemessen. Es ergab sich, dass die axiale Kraftverteilung recht linear ist, und die Gradienten wurden unter Berücksichtigung des Kräftegleichgewichts am infinitesimal kleinen Punkt eines Kabelbolzens als Haftfestigkeit interpretiert.

Jan 1, 2003

By C. A. Snyders

The research presented in this paper investigated the practical aspects of the recovery of platinum group metals (PGMs) from a dilute cyanide leach solution containing base metals, in a manner similar to that used for gold extraction in a typical CIP process, and focuses on both the adsorption and elution stages. The carrier-phase extraction of precious metals using activated carbon offers significant advantages over other processes in terms of simplicity, the high pre-concentration factor, rapid phase separation, and relatively low capital and operating costs. As a sorbent, activated carbon is still by far the most important material because of its large surface area, high adsorption capacity, porous structure, negligible environmental toxicity, low cost, and high purity standards. Adsorption tests were conducted on a pregnant alkaline leach solution (0.15 ppm Pt, 0.38 ppm Pd, 0.1 ppm Au) resulting from cyanide extraction performed in column leach tests. The initial adsorption rates of Pt, Pd, and Au were very fast and recoveries of these three metals were approximately 90 per cent after 2 hours, and 100 per cent for Pt, 97.4 per cent for Pd, and 99.9 per cent for Au after 72 hours. The parameters that influence the extraction of PGMs and Au were examined to assess their relative importance during the adsorption process in order to provide the basis for process optimization. The concentration of thiocyanate was not identified as significant factor for PGMs adsorption, while Ni concentration was the most significant extraction process parameter. Base metal cyanide complexes adsorb and compete with the PGM complexes for sites on activated carbon, and while copper adsorption can be minimized by adjusting the residence time, Ni adsorbs at approximately the same rate as the PGMs, influencing the loading capacity and adsorption kinetics of the PGMs. The feasibility of eluting platinum and palladium cyanide complexes from activated carbon using an analogue of the AARL process was investigated. Platinum and palladium elute from activated carbon almost to completion in 4 to 5 bed volumes at 80°C, while the elution of gold at this temperature is slow, with a significant amount of gold still to be eluted after 16 bed volumes. The equilibrium loading of gold is exothermic in nature (Fleming and Nicol, 1984) which will result in an increase in gold elution kinetics with an increase in temperature at similar pre-treatment conditions. A similar result was found for the elution of Pt and Pd. Cyanide pre-treatment was found to have a significant influence on PGM elution. Higher cyanide concentration in the pre-treatment step results in more efficient elution up to a point, and results suggest the possibility of an optimum cyanide concentration, beyond which elution efficiency starts decreasing due to increased ionic strength.

Jan 1, 2013

By D. Pienaar, C. O’Connor, B. McFadzean

Dithiophosphate (DTP) is classically used as a co-collector in sulphide mineral flotation, where xanthate-DTP mixtures have been shown to synergistically improve mineral flotation performance. Notwithstanding the improved recoveries observed, ethyl DTP does not appear to behave as a conventional collector, since it has been shown that it does not adsorb onto certain sulphide mineral surfaces. Recent investigations have nevertheless indicated that when ethyl DTP does not adsorb onto the sulphide mineral surface, the presence of a non-ionic frother can activate a synergistic increase in pulp phase mineral recovery, and bubble-particle attachment probability. A regular solution approach was used to determine the interactions between thiol collectors and non-ionic frothers at the air-water interface. Attractive interactions were observed between longer alkyl chain DTPs and frothers, whereas the activity of xanthates at the air-water interface were too weak to determine if an interaction was occurring. This is the first time that such interactions have been shown for the DTP-frother system and represents an important contribution to our understanding of the role of DTP reagents in the flotation process. Keywords: Collector-frother interaction, dithiophosphate, surfactant synergism

Jan 1, 2020

By J. S. Preston

The properties of some recently developed solvent-extraction reagents for the separation of cobalt and nickel sulphate solutions are reported. New commercial extractants based on alkyl phosphonic and alkyl phosphinic acids are described. These reagents show much improved selectivity for cobalt compared with established extractants. Some novel extractants developed at Mintek for the selective recovery of nickel in the presence of cobalt are also described. These reagents, which are based on mixtures of carboxylic acids and non-chelating oximes, are of interest in that no commercial nickel-selective reagents are currently available. Graphs showing metal loading and stripping, and pH-functionality, are presented. together with details of the metal separations achieved in batch countercurrent- extraction experiments with the various reagents.

Jan 1, 1983

By Z. Botha

Sheryl Sandberg, the COO of Facebook, published a book titled 'Lean In', where she invites women to sit at the table. In summary, to 'sit at the table' entails not only embracing opportunity, but to actively seek out opportunities in leadership positions. Sandberg points out that, unfortunately, apart from institutional obstacles, a woman's own perceived limitations have a negative impact on her leadership ambitions. To create an environment where diversity will flourish, where everyone has a seat at the table and everyone has a voice, safety must be established first. To establish safety within a diverse team, there is power in relationships and connections. This study will first and foremost review theories in literature as to why diversity and inclusion are so important and the value that diversity brings to our industry. The study also recommends a few focus areas for improving diversity and inclusion in the industry.

Sep 1, 2022

By Axel Schulze

HUGO PETERSEN has developed from the traditional firm of the same name that was established in 1906 in Berlin and is an engineering company specialising in general plant engineering now based in Wiesbaden. HUGO PETERSEN has many years wide-ranging experience in process plant engineering, primarily in the field of Sulphuric Acid Processes and Gas Cleaning. Together with its main shareholder, Chemieanlagenbau Chemnitz GmbH (CAC), a company with over 40 years experience in the international plant engineering business, HUGO PETERSEN implements turnkey new plants from initial consultancy right through to commissioning. In addition, HUGO PETERSEN can offer its clients improvements and revamps of existing plant systems. Initial consulting, planning and implementation take place within the context of a lean company organisation with experienced engineers and specialists. In all respects, many years of experience guarantee expertise over a wide range of possible applications For clients from the chemicals and metallurgical industries, as well as those in metals processing, HUGO PETERSEN GmbH?s breadth of experience means not just an efficient introduction to new methods and processes, but also their full implementation. In addition, along with design and construction for individual components, the company?s range of services also covers supply of complete plants, as well as modernisation projects and revamps in line with local conditions and existing quality requirements With own technologies and patents in the field of gas cleaning and sulphuric acid, supplemented by licences and cooperation projects, HUGO PETERSEN ensures expertise over a wide range of applications. With specialists and expert knowledge in these fields of application, HUGO PETERSEN is your partner of choice, supporting you and bringing your acid, and project to a successful conclusion.

Jan 1, 2009

By D. J. Adams, R. G. Gürtunca

In situ measurements and numerical modeling based on elastic theory showed that backfill stresses are considerably higher than originally thought. This has led to a change in understanding of rockmass behaviour. After describing previous work on the behaviour of the rockmass, this paper discusses possible reasons for the high stresses measured in backfil, and identifies the rockmass mechanisms possibly generating these stresses. It is concluded that the joints and the geological stratigraphy can lead to increased elastic convergence, and that the inelastic behaviour of the rockmass is also partly responsible for the increased closure measured in backfill. The use of an in situ modulus is suggested as an interim solution until a new computer model that allows for joints, different layers, and inelastic closures becomes available.

Jan 1, 1991

By M. L. Mahlatji

Mechanical alloying of an equiatomic mixture of crystalline Ti and Pt elemental powders in a high-energy ball mill formed an amorphous alloy by solid-state reactions. Mechanical alloying was carried out in an argon atmosphere at a rotation speed of 1200 r/min and a 20:1 ball-to-powder weight ratio, for time intervals of 4 to 40 hours. At an intermediate stage of mechanical alloying, scanning electron microscopy showed the formation of characteristic layered structures of inhomogeneous composition within the powder particles. X-ray diffraction analysis showed the gradual disappearance of crystalline Bragg peaks and the emergence of broad amorphous maxima as milling progressed. The amorphization process was completed after 8?12 hours. The amorphous state of the product indicated that temperatures during processing did not exceed the crystallization temperature of the alloy.

Jan 1, 2014

By J. D. Austin, D. G. Kringe

Rates of return realized on investments in the gold mines of the newer goldfields outside the Witwatersrand were calculated and analysed over various time intervals and on various bases. It is shown that these rates of return are strongly correlated with changes in the gold price and cannot be equated with the returns that are expected when investments are made, and that the changes in gold price also affect the rates of return on the Johannesburg Stock Exchange as a whole. These correlations are used, together with a limited application of the Capital Asset Pricing Model, to suggest the expected levels of threshold returns in real terms for new mining projects, for projects on existing mines, and for share valuations.

Jan 1, 1980

By J. M. Barnard, M. P. Brandt, L. E. Korwin-Kossakowski, W. H. Smith

Petrographic analyses of coal rank and maceral-group composition are widely used in the characterization of coal. This paper describes the use of an image analyser (IBAS Kontron) for fuly automated measurements of the rank and maceral groups of seam coals. The rank is then derived from reflectance histograms, or 'fingerprints', of coal reflectance distributions (being expressed as the mean random reflectance of vitrinite). The volume proportions of the maceral groups are calculated from the histograms. The results obtained with the IBAS were generally in agreement with those obtained by conventional methods of reflectance measurement and point-count analysis. However, the results were inconsistent for coals with a bimodal character or a wide V-class distribution. The rank of the analysed coals ranged from 0,50 to 1,10 per cent mean random reflectance. The lowest reflectance that can be analysed with the IBAS is 0,4 per cent. The speed, objectiveness, and repeatability of this technique make it exceptionally suitable for use in the quality control of large numbers of samples.

Jan 1, 1990

By A. Santana, J. Jankolovits, G. S. Reyes

The flotation of sulfide ores that contain carbonaceous gangue requires significant operational and chemical intervention to achieve suitable metallurgical outcomes. Carbonaceous gangue dilutes concentrate grades, alters the froth behaviour, reduces operational stability, adsorbs reagents, and reduces value recovery. Carbon management processing strategies like preflotation and depression are often presented as point solutions. Moreover, oversimplified mechanisms of carbon depressants belie their complex and nuanced impact on flotation behaviour. Optimising the flotation of carbonaceous sulfide ores requires a holistic consideration of interactions between the carbon management reagents and the processing strategy, ore mineralogy, flotation behaviour, flowsheet, and all other aspects of the flotation system. Examples are shown where conventional, simplistic mechanisms of carbon depressants fail to explain the observed flotation behaviour. The multifaceted impacts of carbon depressants on froth behaviour, collector performance, and value recovery highlight the need for a holistic approach to carbon management. Keywords: Carbon management, carbonaceous ores, sulfide flotation, carbon depressant

Jan 1, 2020

By S. Purushotham, Y. R. Murthy, M. Narasimha, S. K. Tripathy, M. Kumar

Spiral concentrators are gravity-based separators widely used to beneficiate coal, heavy minerals and beach sand. It consists of a helicoid trough that spirals downward in the helical configuration around an axial column. The particle segregation takes place based on size and density under the influence of gravity as the particles spiral down within the thin water layer. In the last century, most design modifications of this equipment were based on trial and error based lab-scale experimentations and empirical approach. The use of Computational Fluid Dynamics (CFD) has gained interest in the past two decades to understand the underlying flow physics in the spiral concentrators. In this paper, we used CFD to model the fluid flow and investigate the particle segregation inside a conventional LD9 spiral concentrator. Firstly, the Volume of Fluid model was used to resolve the liquid-air interface. The liquid depth and flow field predictions for varying flowrates were validated against the experimental literature data. One-way coupled VOF-LPT model was then used to describe the particle dynamics in the spiral flow field assuming dilute particulate flow. Moderate dense particulate flow (20 vol.%) was then modelled using the Algebraic Slip Mixture (ASM) model. Four particle-phases representing particles of different sizes of dual-density were simulated, and the component particle segregation was analysed. Keywords: Spiral concentrator, two-phase flow, multiphase, discrete phase model, ASM model

Jan 1, 2020

By D. Govender

Theoretical flotation models suggest that there is a positive relationship between bubble-particle collision rates and turbulent kinetic energy dissipation. Fine particle flotation performance is generally enhanced by increased collision frequency and hence higher energy dissipation. Contrarily, increased turbulence in the rotor-stator region is related to higher detachment frequency of the coarser size range. Therefore, the optimal modes of recovery for the ?fine? and ?coarse? size classes appear to be diametrically opposed. Industrial applications have previously confirmed that applying greater power to flotation slurries yields significant improvements in fine particle recovery. However, recovery of the coarser size class favours a different flotation environment. An improvement in the flotation kinetics of the fine and coarse size classes, provided there is no adverse metallurgical influence on the intermediate size ranges, is obviously beneficial to the overall recovery response. Managing the local turbulent kinetic energy dissipation, and hence the power imparted to the slurry, offers the benefit of targeting the particle size ranges exhibiting slower kinetics. FLSmidth recently introduced the practical implementation of this concept. In principle, it decouples flotation regimes where fine and coarse particles exhibit preferentially recovery. In the case of naturally aspirated machines (Wemco®), it is referred to as Hybrid Energy Flotation? and incorporates at least three phases: ? Standard flotation machines (standard energy input, rotor speed (r/min), rotor size/type) at the beginning of the row, where flotation is typically froth-phase limited and operational and set-up parameters have a limited influence on the recovery ? Higher-powered flotation machines (high rotor speed, high-power rotor size/type) at the end of the row to improve fine particle recovery ? Lower-powered flotation machines (low rotor speed, low power rotor size/type) to enhance coarse particle recovery. A CFD-based flotation model is used to highlight the effect of turbulent dissipation energy on attachment and detachment rates. Preferential collection zones for ?fine? and ?coarse? particles are predicted for both forced-air and naturally aspirated machines. The greater predominance of UG2 ore types, coupled with the skewed feed distribution of platinum group metals (PGMs) to the finer size fractions, suggests that PGM flotation circuits are not designed for optimal recovery across the size distribution. The application of the hybrid energy concept to PGM flotation offers a possible shift towards a more efficient flotation circuit solution through a managed distribution of energy.

Jan 1, 2012

By L. Tartibu, S. Assuli, P. Nkul, A. Kabimba, W. Elongo, N. Makhotla, D. F. Verwey, F. G. Ndiitwani, J. Bilali, T. Mukongo

The presence of colloidal silica negatively impacts various hydrometallurgy processes. This paper details the nature of colloidal silica, operational issues caused by colloidal silica, as well as various mitigation measures. MMG Kinsevere observed severe phase-continuity instability, increased crud formation, and reagent consumption, and reduced current efficiency in electrowinning with a deterioration in copper quality. Historical mitigation measures were initially implemented but failed to solve the problem. MMG Kinsevere successfully achieved efficient silica removal without adverse effect on the solvent extraction with the use of DEHSCOFIX® SC12 coagulant. A week into the coagulant trial, silica concentration had dropped from > 1500 mg/L to within 500 mg/L. The solventextraction plant recovered its stability and again operated at maximum capacity. Additionally, improvement was observed on current efficiency and copper cathodes quality with use of the coagulant.

Jan 1, 2023

By P. J. Petit

Financial evaluation is necessary to investigate the viability of implementing and/or utilising new technology in mining projects. It establishes a techno-economic base for decision-making and justifies capital expenditure. This paper aims to present a monetary appraisal of the electric rock drilling system in a typical feasibility project, whose purpose is to increase the production rate. The in situ environment is a platinum orebody, and the stoping operations occur in UG2 reef. The results are a function of production requirements, technical parameters and financial outlay of the drills. The costs involved in implementing and operating electric rock drills are assessed to the current method of drilling, namely the compressed air operation. A comparison of the electric and pneumatic rock drills in terms of financial outlays for drilling and service requirements, peripheral equipping and training is discussed. Other factors that affect the business case are technical advantages, safety and risk management and the environmental objective of the company.

Jan 1, 2006

Jigging is a process of particle stratification in which the particle rearrangement results from an alternate expansion and compaction of a bed of particles by a pulsating fluid flow. The rearrangement results in layers of particles that are arranged by increasing density from top to bottom of the bed. The particles, in addition to the vertically expanded and compacted bed motion, move continuously, horizontally across the supporting screen and helped and influenced by the feed material that is introduced at one end. Following the particle stratification, the particle bed is physically ?cut? at a desired horizontal particle density plane to separate the desired product from the less dense gangue material. The issue of correct pulse characteristics (shape, amplitude and frequency) for the optimal metallurgical stratification of air pulsating jigs has been the subject of much discussion over the years. The accuracy of the dissymmetric stratification depends on the control parameters and the mechanical condition of specific equipment used. This paper will touch on some of the control and mechanical parameters affecting the separation efficiency.

Jan 1, 2010

By H. S. Sichel, Kleingeld

A frequency distribution model plays a fundamental role in ore evaluation, especially for the feasibility study of new deep gold mines. The geological complexity of the reefs being mined at present in the Witwatersrand basin poses some difficulties regarding the modeling of the underlying ore-value distribution. This geological complexity has given rise to a need for more applicable distributional models. This paper places the geology of the Witwatersrand basin in perspective and draws some important conclusions from the genesis of the deposition. In addition to the three-parameter lognormal model, two more-general distributional models are proposed. These are the compound lognormal (CLD) and log-generalized inverse Gaussian (LN-GIG) distributions. A detailed, although preliminary, comparative study of these two more-general models with the three-parameter lognormal model is described, and the efficiencies of the estimates and modeling are analysed. It is found that the broad assumption that gold grades follow a three-parameter lognormal law is not always the case, and the need to test for departures from log normality should be emphasized so as to ensure the use of appropriate models.

Jan 1, 1992

By L. Thomas, D. Muteba, L. I. Nsenga, B. Mbao, G. Longo Banza

Owing to the high ore grades in the African Copperbelt and variable acid consumption, agitated leaching is common practice and is used more widely in Africa than in other regions. Two common challenges for agitated leach–solvent extraction circuits are higher presence of colloidal silica in the pregnant leach solution and elevated levels of total suspended solids. Both can negatively affect the physical and metallurgical performance of the solvent-extraction circuit, and lead to higher processing costs or reduced copper production. Operating in organic continuity is preferred to address such challenges, but is not always possible: additional treatment options may be advantageous. For this reason, Solvay recently introduced ACORGA® CR60LT, a new chemical additive to address these concerns. Continuous addition to the pregnant leach solution improves physical performance without negatively affecting Cu transfer or cathode quality. Results and benefits from commercial utilization of ACORGA® CR60LT at different operations in the Copperbelt are reviewed

Jan 1, 2023

By J. van der Walt, A. Whillier

Reference is made to the approach to mine cooling in which the service water is used as one of the means of distributing refrigeration, and attention is drawn to various engineering disciplines or functions necessary for effective distribution and reticulation of cold water from refrigeration plant. The demand for service water is intermittent, the peak flow-rates being typically two to three times the average flowrate. The refrigeration plant, on the other hand, must preferably be operated steadily throughout the day and night, with the result that a large storage dam for cold water must be incorporated into each system in order to even out the surge in demand for water. These dams should be operated as constant-temperature, variable-volume reservoirs. The conventional cascade system involving dams on each level is not the best for sending water down mines, and schemes are described that avoid the need for such dams. Reference is made to various tests that were carried out, and to several large systems that were installed. Management and organizational problems that could arise as a result of new technological developments in mine cooling are referred to, and cost figures are quoted to indicate the large potential savings, In addition to the improved environmental conditions, that can be achieved through the use of integrated water systems.

Jan 1, 1979

By A. Bain

The use of plastics in the coal mining industry is making slow progress whereas these materials could make a greater contribution to safety, to a reduction of working costs and to the higher productivity of mine workers. Possibly the reluctance to experiment with the new material of our age is due to the low profit margin of coal mining. This note has been prepared to present a brief survey of what has been done in the last few years and to mention some of the investigations the author has made and is making in an attempt to develop more use of plastics in the industry. Some of the plastics used on the mines have taken their place in the industry in the same manner that they are used in everyday life while others have been introduced because there has been a need for them. New uses and applications are being developed and these are the ones that are most interesting. The plastic that is specially developed to give the maximum benefit and not the one that is a modification of some other everyday product is the next development in the field. Many manufacturers are keen to promote such investigation but are not aware of the problems the mines wish to solve and therefore it is only through management itself that this development can be carried out. This note deals with plastic material under three headings: (a) Plastic as the superior material, and briefly describes how plastic has replaced a few major items which are better when made from plastic. (b) Plastics of necessity, being a short summary of how plastics had to be introduced because of laws and conditions making it a necessity. (c) Development of new ideas, being briefly some of the ideas being developed overseas and some of the ideas being tried by the author. Plastic items in common use such as in housing, electric cables, laboratory equipment, awnings, nylon bearings, locomotive brake linings, etc. being well known are not discussed. PLASTIC AS THE SUPERIOR MATERIAL Plastic belting underground Following a fire in a belt road in England resulting in the deaths of many workers, and subsequently a fire accompanied by fatalities in a belt road in a mine in this country, a law was introduced which states that only flameproof belting is to be used underground. This ruling forced the mines to use P.V.A. belting as no other was available. This belting has non-inflammable characteristics that are superior to rubber. Due to the high tension on long-distance belts used today the need for stronger belting material called for something better than cotton and the answer to this was nylon. Nylon also has the ability to withstand dry-rot which reduces the life of a belt very quickly.