Search Documents

By A. Tosun

Muckpile fragmentation formed by blasting depends on the specific charge factor, the discontinuities in the rock mass, and the rock strength. Determination of the discontinuity characteristics and rock strength is a long and difficult process. These two parameters are directly associated with the rock drilling speed. Therefore, it is the drilling speed of the machine used for the blast-hole, rather than the blasthole discontinuity characteristics and rock strength parameters, that is used in the prediction of muckpile fragmentation before blasting. Primarily, it has been suggested that the muckpile fragmentation values can be correctly determined by establishing correlations between the efficiency of the loader and muck pile fragmentation, since fragmentation is directly correlated with the former parameter. Subsequently, a correlation predicting the drilling speed of the drill machine was developed according to the discontinuity characteristics of the blasting surface and the rock strength. Finally, a correlation was developed predicting muckpile fragmentation according to the specific charge factor and the drilling speed of the drill machine The data was obtained by conducting blasting tests in two different limestone quarries.

Nov 30, 2022

By Sylvie Poirier

Researchers at Natural Resources Canada (NRCan) CANMET Mining and Mineral Sciences Laboratories (CANMET-MMSL) and Mining Technologies International (MTI) have designed and built a hybrid diesel-electric mining loader that is the first of its kind to be developed for underground mines. Diesel equipment is popular because of its mobility and most mining operations are reluctant to replace it with tethered electrical equipment despite the obvious elimination of diesel contaminants and significantly lower heat generation (? 35% of an equivalent diesel). However, a diesel-electric vehicle, being currently evaluated by CANMET-MMSL, could be beneficial. In this unit, a constant load diesel generator feeds batteries which, in turn, powers electrical motors that drive the equipment. In a hybrid diesel-electric unit, the constant load diesel generator can be optimized for minimal emissions and hence lower dilution air requirements. This paper will present the project status and the anticipated benefits for mining operations through the application of this technology.

Jan 1, 2008

By D. B. Swanepoel

Hulamin Rolled Products (Ltd) developed a high Mn and Si containing alloy, EN 4017 as a scrap consuming alloy from the waste generated in producing their range of clad products for brazing of inter alia automotive heat exchangers. The multifaceted composition of this alloy (Al -1.2 wt% Si -1.1 wt% Mn -0.2 wt% Mg-0.26 wt% Cu) suggested that it might display some degree of strengthening via precipitate formation of the Mg2 Si-types. The aging isotherms constructed showed that EN 4017 with 0.19% Mg reached a lower peak strength (YS~210 MPa and UTS~260 MPa)compared to the EN 4017 material with 0.43% Mg (YS~270 MPa and UTS~325 MPa). The higher Mg variant of EN 4017 was comparable with the age-hardenable reference alloy EN 6061. Selected area electron diffraction (SAED) studies proved that the microstructure of age hardened EN 4017 contained a combination of ß', ß" and U2 phase after being aged at 175ºC for 65 h. The general microstructure contained precipitate free zones as well as grain boundary Si films, although these did not lead to significant embrittlement. The role of Mn dispersoids in the fracture mechanism of 4017 is also discussed. The article will compare the behaviour of EN 4017 with that EN6061. Keywords: Age-hardening, dispersoids, magnesium silicide, precipitate free zones

Jan 1, 2009

By L. Robles-Stefoni

"Multiple-point simulation (MPS) methods have been developed over the last decade as a means of reproducing complex geological patterns while generating stochastic simulations. Some geological spatial configurations are complex, such as the spatial geometries and patterns of diamondbearing kimberlite pipes and their internal facies controlling diamond quality and distribution.Two MPS methods were tested for modelling the geology of a diamond pipe located at the Ekati mine, NT, Canada. These are the single normal equation simulation algorithm SNESIM, which captures different patterns from a training image (TI), and the filter simulation algorithm FILTERSIM, which classifies the patterns founded on the TI. Both methods were tested in the stochastic simulation of a four-category geology model: crater, diatreme, xenoliths, and host rock. Soft information about the location of host rock was also used. The validation of the simulation results shows a reasonable reproduction of the geometry and data proportions for all geological units considered; the validation of spatial statistics, however, shows that although simulated realizations from both methods reasonably reproduce the fourth-order spatial statistics of the TI, they do not reproduce well the same spatial statistics of the available data (when this differs from the TI). An interesting observation is that SNESIM better imitated the shape of the pipe, while FILTERSIM yielded a better reproduction of the xenolith bodies. IntroductionThe simulation of geological units poses several technical problems that challenge the capabilities of available geostatistical simulation approaches and their ability to deal with spatial complexity of categorical variables. The spatial geometry of diamondbearing pipes and their internal facies controlling diamond distributions are a specific and well-known difficult modelling problem. The geometry of a kimberlite pipe is typically like an inverted cone (Figure 1); the wider part is known as the crater and is located near the surface, and the narrower, deeper part is known as the diatreme. Xenolith bodies can also be found inside the pipe. A very important contribution to the geological modelling of the contours of the pipe is the measure of uncertainty about the location of the contact between the kimberlite pipe and the host rock."

Jan 1, 2016

By A. Nhasengo

Paper written on project work carried out in partial fulfilment of B. sc. Eng (Mining Engineering) The purpose of this investigation was to assess the mining strategy for steep reefs at Mine A mine in 2005 and 2006. Reefs steeper than 35° were discovered when production commenced at the mine. At that time reefs steeper than 35° were not popular in South African tabular gold mines, therefore new techniques of mining them had to be developed. The underhand mining method was chosen for this purpose. The project was about assessing ventilation, support costs, local support cycles, adherence to the mine?s support standards, mine planning and efficiencies of the underhand mining method. The project work was covered by doing a literature research for underhand mining methods and performing a literature review of the mining methods, support methods, ventilation standards at Mine A. Underground visits were conducted at Mine A mine for data collection, and Mine B was visited to obtain information on support costs and efficiencies. During the investigation it was realized that the underhand mining method was an appropriate method for mining steep reefs; however, there were some challenges related to ventilation and support installation. Efficiencies could be realized with the underhand mining method and planning and scheduling were not different from breast mining.

Jan 1, 2007

The first annual student prizegiving function of the South African Institute of Mining and Metallurgy was held in the Dorothy Susskind Auditorium, University of the Witwatersrand, on Thursday, 26th May, 1977. The address (see opposite page) was given by Dr M. G. Atmore, a director of Anglo American Corporation and Vice-President of the Institute.

Jan 1, 1977

By X. H. Li, Q. Zhang, X. Fei

Bauxite residue known as red mud (RM) is a by-product produced in massive quantities during alumina production by the Bayer process with a utilisation rate of less than 5%. A large amount of RM accumulated and produced continuously has had a seriously adverse impact on the surrounding ecological environment. The application of RM in building materials is considered to be the most effective and thorough way to make RM harmless and recycle resources for the reason that adding RM to concrete as a mineral admixture could not only consume a lot of RM, but also save cement and other energy-consuming industrial products. In this paper, the adaptability to cement and aggregate of RM was studied. The results showed that the compressive strength and flexural strength of concrete using ordinary Portland cement, slag Portland cement or fly ash Portland cement as cementing material showed different trends with the increase of the amount of RM. The influence rules of RM on the compressive strength of Portland cement, slag Portland cement and fly ash Portland cement concrete were similar, whether for silicate aggregate or carbonate aggregate. RM has a negative correlation to the flexural strength of silicate aggregate-ordinary Portland cement concrete, but a positive correlation to silicate aggregate-slag Portland cement, silicate aggregate-fly ash Portland Cement. RM promoted the formation of calcium carbonate crystals and inhibited the formation of ettringite and calcium hydroxide crystals in the matrix while ordinary Portland cement, Portland cement and fly ash Portland cement were used as cementing materials. This study provided support for the use of RM in concrete, the reduction of solid waste storage, and the saving of high energy consumption cement as well. Keywords: Red mud, cement, aggregate, adaptability, mechanical properties, mineral composition

Jan 1, 2020

By A. W. Cramb

A three-day symposium on the production of clean steel organized by The South African Institute of Mining and Metallurgy, was held in September 1995 at Vanderbijlpark. It was attended by 151 delegates, who represented the whole of the steel industry in South Africa: Iscor Works, Saldanha Steel, Columbus Stainless, Highveld Steel & Vanadium, Iscor Research & Development, University of Pretoria, and Technikon Witwatersrand, as well as the users of steel products were represented. Professor Allan Cramb held the delegates attention with well-presented research and practical information. He obtained excellent interaction with the delegates by responding in depth to the questions put to him during the Symposium. In summary, he emphasized the following aspects of the elimination of defects during the processing of steel in continuously cast materials.

Jan 1, 1996

By E. C. de Beer

"SynopsisA number of important areas in nuclear fuel cycle, at both the front end and back end, offer ideal opportunities for the application of non-destructive evaluation techniques. These techniques do not only provide opportunities for non-invasive testing of e.g. irradiated materials, but also play an important role in the development of new materials in the nuclear sector. The advantage of penetrating radiation used as probe in the investigation and testing of nuclear materials makes X-ray and neutron radiography (2D) and tomography (3D) suitable for various applications in the total nuclear fuel cycle. The unique and different interaction modes of the two radiation probes with materials provide several opportunities. Their complementary nature and non-destructive character makes them most suitable for nuclear material analyses, analytical method development, and the evaluation of the performance of existing nuclear material compositions. This article gives an overview of the X-ray and neutron radiography/tomography applications in the field of nuclear material testing, and highlights a few of the success stories. Several selected areas of application in the nuclear fuel cycle are discussed to illustrate the complementary nature of these techniques as applied to nuclear materials.IntroductionDuring the development of new materials for the nuclear industry, materials testing and characterization are of the outmost importance to maintain safety standards and reliability. No compromise on safety in the workplace in any area within the total nuclear fuel cycle can be tolerated, and therefore most in-situ material characterization and testing is conducted by certified and qualified personnel schooled in destructive and non-destructive testing (DT and NDT) methods. Certification and qualification in NDT can be obtained through many training centres in South Africa in accordance with European, American, and other international standards (SGS, n.d.; SAIW, n.d.; African NTD Centre, n.d.)."

Jan 1, 2015

By W. Newcomen, G. Dick

"Effective management and mitigation of pit slope instability in open pit mines begins with a comprehensive slope monitoring programme. The ability to differentiate between non-critical pit wall movements due to rebound or relaxation of the excavated slopes and movements that may be indicative of slope failure is important for maintaining a safe working environment and maximizing production. Slope failure prediction methods using velocity, acceleration, and strain criteria have been introduced and put into practice over the past few decades. Forty-eight slope failures with surface monitoring data are presented and assessed using the strain-based failure prediction approach, with consideration of the quality of the rock mass and the potential failure mechanism. The results indicate that the strain-based approach can be used to provide general guidance regarding strain thresholds for pit walls for a variety of failure modes in diverse geological environments. The advantages and potential drawbacks of the strain-based and other slope failure prediction methods are discussed. The importance of implementing a pit slope monitoring and performance evaluation system early in mine development is also emphasized. IntroductionThe successful prediction of the Manefay Slide pit slope failure at Bingham Canyon at 9:30 am on 10 April 2013 (Engineering and Mining Journal, 2014) highlighted the importance of having a comprehensive slope monitoring system that provides an accurate prediction of the time of failure of an open pit slope. Using most of the geotechnical monitoring tools available, the time of the failure was predicted within hours and equipment and personnel were evacuated from the pit well in advance of the failure. From a time to slope failure perspective, the monitoring system in place was a success.There are two general groups interested in monitoring pit walls, with slightly different objectives in mind when the monitoring system is being set up. There are those at the mine site that have to implement the pit slope design, monitoring protocols, and the action response plans, and there are those designing the slopes (often consultants) who regularly visit the mine but may not be responsible for the day-to-day activities. was a success.There are two general groups interested in monitoring pit walls, with slightly different objectives in mind when the monitoring system is being set up. There are those at the mine site that have to implement the pit slope design, monitoring protocols, and the action response plans, and there are those designing the slopes (often consultants) who regularly visit the mine but may not be responsible for the day-to-day activities."

Jan 1, 2016

By S. Marx

More than twenty years ago Sasol, ISCOR, and some parastatals played a major role in ensuring that South Africa had sufficient technical skills. When the economy became tight and business and government were pressurized to decrease costs, the first budgets that were reduced were the training budgets. It seemed to be too expensive and too time-consuming to train apprentices. According to Stacey2, this is a major strategic issue facing the mining industry in South Africa. Two factors added to the shortage of skills challenge: ? Skills erosion and job losses ? Artisans ? currently the economy produces 5 000 but the need is 12 500 ? Level of mechanization in South Africa less than 10 per cent ? Average age of operators and artisans is 50 ? Greater awareness of occupational health effects of hand-held drilling. ? Workplace challenges ? The impact of HIV/AIDS and other employee wellness issues ? Changes and challenges in workplace environment i.e. the mining industry.

Jan 1, 2012

By X. J. Lyu, Q. Liu, M. J. Lian, X. Q. Cao, X. F. You, B. O. Erdenekhuyag, H. Y. Zang

The slag-tailings based artificial reef concrete (ARC) is made of CaO-CaSO4 activated granulated blast furnace slag (GBFS) as cementitious material and deslimed gold ore tailings as aggregate. In order to investigate the potential application of the material as ARC, the strength development, hydration characteristics and application performance were investigated under different preparation conditions. Results indicated that using seawater as the mixing water can effectively promote the hydration of slag and generate a large amount of hydration products such as ettringite, CSH gel, hydrotalcite and Friedel ’s salt in the early curing period and so render the material with good early compressive strength. Seawater curing can also accelerate the hydration reaction in the early stage of hydration. The hydration reaction of slag and the compressive strength of ARC can be effectively promoted by increasing the specific surface area of slag. The 28-day compressive strength of the slag-tailings based ARC prepared with 30-50% CaO-CaSO4 activated slag and 50-70% tailings can reach to 19.88-42.87 MPa. Also, the material has a low surface pH value, good resistance to chloride ion penetration, and sulfate corrosion. Keywords: Artificial reef concrete, granulated blast furnace slag, deslimed gold ore tailings, compressive strength, hydration characteristics

Jan 1, 2020

By A. N. Brown

The Hendrik van der Bijl Memorial Lecture is arranged annually under the auspices of the Pretoria Engineers Liaison Committee. This is a multidisciplinary Committee with representatives from eleven societies and associations, and serves the interests of engineers resident in the Pretoria area. Coal preparation The Japanese Organizing Committee of the 11th International Coal Preparation Congress is now busy making the necessary arrangements for the Congress, which is to be held in Tokyo from 22nd to 26th October, 1990.

Jan 1, 1989

INTRODUCTION This paper was originally presented at the Platinum Adding Value Conference, held at Sun City from the 4th to 6th October 2004. Narrow reef mining may not be applicable to the base metal operations in Zambia, however, it is considered that the methodology used is equally appropriate to the development of technology and mining methods in mining environments other than narrow reef mining. The purpose of this paper is to explore the integration of technology and stoping systems. For the last hundred years the South African narrow reef mining industry has battled to control working costs in a labour intensive industry. It is only through the application of appropriate technology that change will occur. Stoping systems, because it is the stoping method and methodology that is at the heart of the mining system. Introduce a different technology that results in a more efficient stoping system and the mining system will look after itself. The technology applied to stoping in narrow reef mining, over the last 100 years, can be categorised as follows: ? The introduction of pneumatic rockdrills early this century. The cumbersome rig mounted units being replaced by smaller, lighter, hand held units that were then made easier to use with the addition of an air leg. (The so called Swedish method of mining.) As late as the early 1970s some drilling was still being carried out without the assistance of an air leg. ? Scraper winches to replace gravity and shovels to move rock both in the face and the gullies were first introduced in the late 1920s. ? Hydraulic props installed close to the face and capable of applying force against the hangingwall as well as yielding in a controlled manner under dynamic load arrived in the 1960s. In many instances these have now been replaced by yielding elongates fitted with water hydraulic tensioning devices. ? Some people argue that the introduction of tungsten carbide inserts, to improve drilling, was equally important.

Jan 1, 2005

By M. Splaine, W. Davison, D. C. Atkinson

"Since 1964, Nchanga Consolidated Copper Mines, Ltd., has been developing and using production scheduling methods for optimizing its metallurgical operations in the short term (up to one year). Medium-range metallurgical planning has been possible only by successive evaluations of a single-year L.P. A modified version of Rosenbrock's direct search technique has now been developed to allow multi-year optimization of both mining and metallurgy for medium-range planning. The modifications to the search technique have produced a marked increase in computational efffciency for this heavily constrained problem in many variables and the system is a usable planning tool, given a reasonably powerful computer. The plans are 'optimum' in the sense that they yield the maximum present value of the operations.Each of the resulting five-yearly mine plans forms the basis for further detailed metallurgical evaluation by the established production scheduling system."

Jan 1, 2014

By G. C. Thompson

'Increased underground extraction of coal' was the theme selected for the 1981 mining vacation school, which was held at the University of the Witwatersrand in January and February. The response of the industry to the invitation to register was so good that three separate schools of one week each were arranged between 26th January and 13th February. In terms of the total number of delegates, some 225 actually attending, the school can be described as the most successful ever organized by the Institute.

Jan 1, 1981

By A. F. van der Merwe, R-D. Taylor, M. Jacobs, F. H. Conradie

Total bound moisture (TBM) is a typical quality indicator of industrial-grade gypsum. This gypsum is comprised of three distinct phases, namely anhydrite, dihydrate, and hemihydrate, of which only the latter is of much industrial use. TBM analysis is a lengthy laboratory procedure, and an artificial neural network (ANN) TBM inference measurement is proposed as a fast and online alternative. An ANN inference model for gypsum TBM based on plant data was developed. The inputs to the network were primarily focused on the plant's calciner, and different network topologies, data divisions, and transfer functions were investigated. Furthermore, the applicability of the TBM value as a quality indicator was investigated based on a gypsum phase analysis. A strong correlation between TBM and the gypsum hemihydrate and anhydrite content was found, validating the plant target TBM of 5.8% as a quality indicator. A network topology consisting of one hidden layer with logarithmic-sigmoid (logsig) and pure linear (purelin) transfer functions showed the best performance (R > 90%).

Oct 3, 2023

By Z. Zhang, J. Niu, H. Wang, Y. Xu, J. Shi

Tribo-electrostatic separation is a promising method for effectively utiliing low-grade magnesite resources by removing quartz and improving the grade of magnesite. To determine the chargeto- mass ratios of pure magnesite and quartz, a triboelectric measurement system was employed, and a laboratory tribo-electrostatic separation system was used to separate low-grade magnesite. The results showed that the maximum difference in charge-to-mass ratio between pure magnesite and quartz particles was observed after friction with polyvinyl chloride. The grade and recovery of magnesite increased with temperature and initially increased with increasing voltage, feed rate, and air flowrate before gradually decreasing. The optimal conditions resulted in a concentrate with 46.91% MgO content and 77.36% recovery, while the quartz content decreased from 7.02% to 1.95%. These experimental results demonstrate the effectiveness and potential of tribo-electrostatic separation in removing quartz and upgrading magnesite.

Apr 14, 2024

1. Book reviews Dislocations and properties of real materials, edited by M.H. Loretto. London, The Institute of Metals, 1985. 392 pp. Reviewer: F.R.N. Nabarro Au &Ag heap and dump leaching practice, edited by J.B. Hiskey. AIME, 1984. 162 pp. $20 (member), $15 (student member), $30 (non-member) plus $3.50 for postage and handling. (Order from SME Books, Caller no. D, Littleton, CO 80127, U.S.A.). Reviewer: R.A. Snodgrass The cost and availability of Colombian coal, by Eric D. Jamieson, with the assistance of Kathleen Jamieson. London, lEA Coal Research (14/15 Lower Grosvenor Place, London SWl W OEX). £50 (in member countries), £100 (in non-member countries). Reviewer: W.C. Mather Extraction Metallurgy '85. London, The Institution of Mining and Metallurgy, 1985. £42. Reviewer: R.A. Snodgrass 2. Recent publications Mining annual review 1985. London, Mining Journal, Jun. 1985. 600 pp. £26.50 (surface), £39.50 (air). High heat production (HHP) granites, hydrothermal circulation and ore genesis. London, The Institution of Mining and Metallurgy, 1985. 593 pp. £27 (members), £30 (non-members). Potential mineral resources of Egypt. 144 pp. US$10. Available from Bendix Field Engineering Corporation-MPGAP, Box 1237, Grand Junction, CO 81502, U.S.A. 3. Mintek reports Report M212 South African costs of equipment for the metallurgical industry (1984). Report M213 The response of as-rolled 3CR12 steel to heat treatment. Report M214 A computer programme for use in the development of multi-element X-ray-fluorescence methods of analysis. Report M221 Commodity profiles for selected metals. Report MIO7D Upgrading of alaskite rock to feldspathic sand. (First issued Jun. 1983; reissued Nov. 1985). IMM awards Given below are details of the trust funds to which applications are invited for grants, etc., payable in 1986. Application forms, which must be returned to the Secretary before 17th March, 1986, are available on request. Applicants should note that, in general, preference will be given to members of the Institution.

Jan 1, 1986

On behalf of the Council and staff of The South African Institute of Mining and Metallurgy, it is my privilege to wish all members and subscribers a very Happy Christmas and a Prosperous New Year.

Jan 1, 1988