Search Documents

By E. K. Stanek, P. Kantabutra, R. A. Wolf

This paper summarizes the cause and effect of induced voltages in multiple conductor cables supplying alternating current power to equipment in under- ground coal mines. The investigation of this phenomenon revealed that the electrical energy produced by the resultant electric arcing between the frames of mobile electric face equipment was of a sufficient magnitude to ignite explosive methane-air mixtures. The results of laboratory tests and field tests made between equipment frames during actual operation in numerous coal mines are discussed. Several methods of eliminating or suppressing the induced voltages to nonincendive levels are also described. It is the purpose of this paper to convey to the mining industry a knowledge of this problem and to recommend methods of eliminating or reducing these induced voltages or arcing currents to safe levels.

Jan 1, 1975

By J. E. Zeilinger

This Bureau of Mines report describes the preparation characteristics of three samples collected from the Kidney seam, in the Northern Field of the anthracite region. Removal of the sink 1.70 specific gravity material from the samples collected would result in greatly reduced ash contents at yields in excess of 90 percent. The Kidney seam, in the locations sampled, proved to be a low-ash anthracite containing an unusually high percentage of float 1.45 specific gravity material.

Jan 1, 1970

By Douglas D. Reynolds, Tarek Deeb, Qunli Liu

Landmines are a great threat to military vehicles and their occupants. Mine blasts can completely destroy vehicles and kill all the occupants or disable the vehicle and leave the occupants severely injured. Injuries sustained during a landmine blast come from fragmentation that enters the vehicle through a hull breach, hot gasses expanding through the vehicle, or shock created from the extreme pressure of the blast (Lafrance, L.P. 1998). Mitigating the high acceleration experienced by the occupants during survivable mine blasts is the focus of the research being addressed in this paper. Method The objective of the project reported in this paper was to prove the feasibility that pneumatic seat technologies that employ light-weight, foam-filled, inflatable air bladder seats and seat backs can be used to protect the crews of lightweight combat vehicles against the detrimental and injurious effects of mine blasts. This protection includes reducing the shock energy experienced by seated vehicle crews during mine blast initiation and at vehicle slam-down to below potentially injurious levels. Figure 1 shows a schematic representation of the proposed lightweight, foam-filled, inflatable mine blast attenuating seat. It will consist of specially designed interconnected seat and seat back lightweight, foam-filed, air bladders that are supported by a rigid frame. [ ] Results Air gun tests and finite element analyses were conducted to determine the effectiveness of a light-weight, foam-filled, inflatable air bladder seat shock isolation system in isolating a vehicle occupant from the injurious effects of a mine blast. Figures 2 through 5 show analytical and experimental results associated with a 65.8 kg mass resting on an inflatable air bladder that is exposed to a shock input.

Jan 6, 2006

By I. D. Shah

Thermal decomposition of copper (II) sulfate (CUS04) and copper (II) oxy-sulfate (CuO?CUS04) are important steps in the overall oxidative roasting of covellite (CuS) and chalcocite (Cu2S). Nonisothermal thermogravimetric techniques were used to investigate the decomposition reactions in flowing Na and air. Thermal decomposition of CUS04 and CuO?CUS04 followed "linear" kinetics with an apparent activation energy of 55±2 and 66±3 kcal per mole decomposed, respectively. These apparent activation energies comply with those previously reported when isothermal kinetic techniques were used. The addition of oxygen decreased the rate of decomposition, while small amounts of iron which were admixed with CuO?CUS04 did not have a significant effect. Neither oxygen nor iron had any appreciable effect on the apparent activation energy of the decomposition reaction.

Jan 1, 1972

By Oliver Bowles

"Waste Granite in the Barre, Vermont, District: Waste in the great granite center at Barre, Vermont, consists of three types of material, the rough blocks rejected at the quarries on account of imperfections, the chips or spalls resulting from trimming and dressing at the cutting plants, and the granular and pulverized material from the dust collectors. The waste piles at the quarries of are immense proportions and constitute a serious handicap to quarrying in that they cover up good rock deposits, and are also so large that waste disposal becomes more and more expensive. The problem of utilization of such waste material is a topic of keen interest to all granite producers.Barre is not situated on a water route, and thus transportation costs prohibit the shipment of waste blocks for rip rap or ballast. Crushing plants use a small amount of this material for road construction, but aside from this, the waste is practically valueless.Investigators of waste utilization problems are awaiting with interest further information concerning an enterprise undertaken at Montpelier, Vermont, to utilize crushed granite for the production of brick similar to sand-lime brick. Granules of granite are mixed with lime, moulded, and hardened under steam Pressure, The brick produced are said to be of excellent quality for structural Purposes.There seems to be no logical reason why waste granite could not be utilized for the manufacture of building stone, and paving blocks, for many of the defects which condemn a stone for monumental purposes are not at all detrimental for building or street paving. F or the most part, monumental stone workers are not particularly interested in other branches of the granite in-dustry, and a combination of industries such as that suggested"

Jan 1, 1920

By K. O. Bennington

The thermodynamic properties of pollucite [(Cs0.650Na0.185Rb0.028)(AlSi2) (05.8630H0.137)?0.19H201 were determined by the Bureau of Mines in collaboration with the Argonne National Laboratory. The standard enthalpy of formation determined by hydrofluoric acid calorimetry is ?Hf°298 = -3,098.52 ±3.63 kJ mol-1. The standard enthalpy of formation from the oxides is ?H298 (from oxides) = -209.50 ±2.38 kJ mol-1. Low-temperature heat capacities were determined by adiabatic calorimetry from 5.0 to 306.1 K. The derived standard entropy is S°298 = 207.24 ±0.43 J mol-1k-1. Enthalpy increments above 300 K were measured by copper-block drop calorimetry from 349 to 674 K. Various experimental data were combined with other data from the literature to calculate the Gibbs energies of formation and equilibrium constants of formation over the temperature range of measurements. Standard enthalpies of formation and Gibbs energies of formation are given as functions of temperature. The Gibbs energy of formation is ?Gf°298 = -2,919.9 W mol-1

Jan 1, 1983

By E. O. Binyon

The Blue Metal corundum-andalusite deposit, in the Buckskin Mining district, Douglas County, Nev., was explored by the Bureau of Mines in 1945. The results of that work were presented in Report of Investigations 3895, exploration of the Blue Metal Corundum Property, Douglas County, Nev. published in August 1946. That report also describes the property in detail, giving location, ownership, history, geology, and data on beneficiation tests. Further exploration was carried on in April and Way 1947, the results of which are presented in this report. The work consisted of 175 feet of drift and crosscut, bringing the total to 398 feet of underground working, as shown in figures 1 and 2. The 23-foot drift, which was the last work of the initial project, was extended 99 feet northward along the shear zone, and three crosscuts, spaced at approximately equal intervals along the drift, were driven to country rock on the hanging and foot walls of the zone.

Jan 1, 1948

By James R. Jones

"The General Leasing Law, which provides for the leasing of deposits of coal, oil, oil shale, gas, phosphate, and sodium in public lands, was approved February 25, 1920.One of the outstanding features of this legislation is the fact that it opens for prospecting and exploitation lands and deposits which have been withdrawn from public use, some of them for several years, pending enactment of legislation better fitted to control the mining and utilization of the particular mineral deposits referred to. These lands are not only made available to the public, but they are opened up under a system which defines better than was ever done in the pas the rights which may be acquired under it.The oil operator, for example, under this legislation will know definitely the extent of the rights he has acquired, as well as the legal conditions under which his expensive drilling and other work of exploration are to be conducted. No longer will he be harassed by the possibility that while he is spending his capital in drilling operations in an effort to make a discovery of oil, his legal rights be contested, in which event the superiority of his claim can only be upheld -- if at all -- after long and expensive litigation. By the same token the coal operator will now be free from the embarrassing restrictions of the old coal-land laws respecting the amount of such land which may be purchased by one person.At the same time that these advantages are being enjoyed by the operators, the public will be guarded against wasteful methods of drilling and mining the oil and gas, and coal deposits, and the other mineral substances enumerated in the act, to the end that these products of Nature, which can not be replaced, may be utilized with a minimum of loss."

Mar 1, 1920

By E. R. Cole

A lead smelting process that appears to present minimal pollution problems has been developed at the Bureau of Mines, Rolla Metallurgy Research Center. Ten and 100 g samples of PbS mill concentrates were vaporized at 1,000° to 1,100° C in a furnace with an inert gas atmosphere during a 2-hour period. The PbS vapor was transported by the inert carrier gas to the reduction zone of the furnace where it was reduced at the same temperature with excess hydrogen to metallic lead. Lead of 99.9 pct purity was produced. The H2S formed can be decomposed into elemental sulfur and water vapor by a modified Claus process. Approximately 90 pet of the Cu and 70 pct of the Ag and Zn remain in the residue and are potentially recoverable. More than 98 pct of the lead in the concentrates was extracted.

Jan 1, 1974

By S. J. Anderson

The Bureau of Mines compared three methods of rock cutting using drag cutters under controlled laboratory conditions. The methods tested were the conventional drag cutting method used on continuous miners, the kerf-core method used on some boring machines, and an experimental method called ripper cutting. All three methods were tested in blocks of Indiana and Kasota limestone. The results of this testing showed ripper cutting to be 30 to 40 pct more energy efficient than both the conventional and the kerf-core methods in Kasota limestone and 35 pct more efficient than the kerf-core method in Indiana limestone. The conventional method was, however, 9 pct more energy efficient than the ripper method in Indiana limestone. These results are considered promising, and more tests are planned with the ripper cutting system.

Jan 1, 1987

Reduce dust on long wall faces by using a gob curtain to lower air leakage Into the gob and raise the airflow along the face. Approach A brattice curtain (gob curtain) Is hung between shield #1 and the rib in the headgate entry forcing the ventilating air stream to make the 90° turn and stay on the face side of the shields rather than leaking into the gob. How It Works Air leakage is greatest in the headgate area because the gob behind the first few shields remains open due to the roof bolts in the headgate entry. In addition to the open gob, there is a large gap between shield #1 and the rib. Prevention of air leakage behind the shields is accomplished by the Installation of a curtain between the first shield and the rib extending from the roof to the bottom. The curtain Is advanced with the shield line each pass and is helpful In maintaining a sufficient air quantity along the face. The biggest Improvement due to this curtain is seen in the first 25-30 shields where the Increased air volume lowers dust concentrations through dilution.

Jan 1, 1981

By L. B. Berger, W. P. Yant, R. R. Sayers

"At the request of the Chesapeake & Ohio Railroad Co. a number of tests were made to determine the temperature, humidity, and composition of the atmosphere in certain tunnels of that railroad between Clifton Forge, Va., and Hinton, W. Va. The purpose of these tests was to determine conditions in the cabs of freight locomotives while pulling trains through these tunnels. Tests were made of two types of locomotives, classified by the railroad company as the H-6 and H-7. Both are of the Mallet type, but the H-6 class has one pair of cylinders operating at boiler pressure and the other pair compound, whereas the H-7 operates all four cylinders at boiler pressure, thereby exhausting steam at a higher temperature than the H-6. It was desired to determine the relation between conditions on the H-6 and H-7 engines under comparable conditions of operation. This information supplements previous tests by the Bureau of Mines, discussed in its Reports of Investigations Serial No. 2624, entitled, ""Temperatures in Cabs of Freight Locomotives Passing Through Tunnels of Chesapeake & Ohio Railroad, 11 by s. H. Katz and E. G. Meiter, July, 1924. Three incidental tests of passenger engines were also made."

Feb 1, 1928

By E. C. Lane

The motor gasoline that is being marketed in the United States this winter (1928-29) is slightly more volatile than that gold a year ago. This characteristic is shown by a slight lowering of the distillation temperatures, particularly at the average initial and 20 per cent boiling points. Daring the past mine and a half years the Bureau of Mines has made semi annual surreys of the gasoline marketed in the United States; the Survey just completed is the nineteenth in the series. The 12 cities in which samples have been collected were chosen as representative of the more important marketing territories, as it was obviously impracticable to obtain a sample of every gasoline sold in the entire country.

Jan 1, 1929

By R. Andre, R. L. Grayson, T. Simonyi

"Results from research directed at determining the reason(s) for the ""rank factor"" in correlations between coal workers' pneumoconiosis incidence and coal seam of employment are presented. Using compliance dust samples collected from two longwall panels operating in coal seams of widely different rank, respirable particles were identified by mineral species under manual scanning electron microscope (SEM) energy dispersive x-ray (EDX) analysis and then further characterized by their physical diameter, general shape, and periphery angularity. Size fractional, mineralogical variations are presented.Of primary significance, the percentage of mineral particles from the higher rank coal seam that were uncontaminated by non-stoichiometric elements for a specific mineral species was twice that of those in the lower rank seam. The relationship held for each mineral species, including quartz. This fact may form the basis for the ""rank factor"" known to exist as well as provide a reason for the contradictory role of quartz and other minerals in previous CWP studies.An important subsequent research priority is now focusing on determining the percent¬age of all respirable dust particles that are minerals versus single-phase organic or multi-phase organic-inorganic complexes. This effort will be accomplished usingautomated SEM-EDX. The mineral purity factor will be developed further, but additional emphasis will be focused on determining the extent of inorganic inclusions in organic particles."

Jan 1, 1988

By John C. Edwards

Several experimental programs were conducted at the Pittsburgh Research Center to investigate the level of mine fire detection and alarm capability possible using state-of-the-art technology. These programs involved comparison of the response and alarm time of optical and ionization type smoke sensors to smoldering and flaming coal combustion in a smoke chamber. Coal combustion experiments conducted in the smoke chamber demonstrated that a CO concentration of 5 ppm above ambient corresponded to an optical density of 0.022m1. For the four smoke sensors for which a continuous analog signal was available, a smoke sensor alarm was defined as the average background signal plus ten times the peak-to-peak noise. This alarm criterion resulted in the association of the alarm for three of the four sensors with a smoke optical density of 0.022m-1. and 0.033m-1 for the fourth smoke sensor. The smoke sensors used in the smoke chamber studies were incorporated into large scale diesel fuel fire experiments conducted under normal ventilation conditions in the Safety Research Coal Mine (SRCM) at the Pittsburgh Research Center. These experiments showed that a diffusion mode smoke sensor alarmed earlier than a diffusion mode CO sensor; and, based upon the measurement of the optical transmission at the location of a pump mode ionization type smoke sensor that a pump mode ionization smoke sensor alarmed at an average smoke optical density of 0.021m" for the twelve experiments conducted. A series of 30 and 330 kW diesel fuel fire intensity experiments were conducted under zero airflow conditions in the SRCM. It was determined that :(I) thermal sensors are inadequate at 30 m from a 300 kW fire;(2) a diffusion mode ionization smoke sensor can be more effective for mine fire detection than a diffusion mode CO sensor;(3) recommendations can be made for sensor spacing in a mine entry based upon the measured CO buoyancy induced spread rates along the mine roof and the time for a developing coal fire to ignite a conveyor belt.

By R. V. Ramani, R. Stefanko, G. W. Luxbacher

MINE VENTILATION NETWORK ANALYSIS

Jan 1, 1977

By Louis D. Dornetto

The effects of electric shocks on man are an important factor in the design of power systems and protective devices. The current levels just below let-go and just prior to the onset of ventricular fibrillation must be known and taken into consideration in the design of power systems and protective devices. Isolated (ungrounded) electrical distribution systems are compared with resistance and solidly grounded systems. The advantages and disadvantages of each are discussed and recommendations are made. Transients on coal mine power systems are a problem that, until recently, have been ignored. Transient voltage levels that can be expected on both the high and low side of the load center and the effects of transients on electronic equipment and personnel are covered.

Jan 1, 1975

By C. M. Frost

Crude shale oil produced by gas combustion retorting of Green River oil shale was hydrocracked over a cobalt molybdate catalyst at operating pressures of 500, 1,000, 1,500, and 3,000 psig, an operating temperature of 8900 F, and a liquid hourly space velocity of 1.0. Hydrogen feed rate was maintained at 6,000 scf/bbl. The volume-percent yields of total liquid product were directly proportional to the operating pressure. Weight-percent conversion and volume-percent yields of gasoline were directly proportional to the log of the operating pressure. Catalyst deposit percentages were inversely proportional to the log of the operating pressure. Nitrogen and sulfur removal rates as well as saturation of the liquid products increased as the operating pressure was increased.

Jan 1, 1973

By E. Morrice

Gadolinium, dysprosium, and yttrium are difficult to electrowin as high-purity liquid metals because of their high melting points (>1,300° C). Samarium metal is difficult to prepare directly by electrolysis because the metal reacts with the electrolyte. In this Bureau of Mines study, the rare-earth metal was electrodeposited on a solid manganese, chromium, or iron cathode to form a low-melting alloy. The alloy was then vacuum distilled to separate the rare-earth metal from the ferrous metal. A typical samarium metal product, obtained as the distillate from vacuum distillation of a samarium-iron alloy, contained 150 ppm oxygen, 80 ppm carbon, and 50 ppm iron as impurities, Gadolinium metal, obtained as a residue from the distillation of a gadolinium-chromium alloy, contained 300 ppm oxygen, 200 ppm carbon, and 100 ppm chromium.

Jan 1, 1969

By Dhaval Patel, Kim Witte, Charles Vaught, Michael T. Stephenson, Steve Booth-Butterfield, Cynthia Zuckerman, Brian L. Quick

This longitudinal field study was designed to encourage Appalachian coal miners in West Virginia and Pennsylvania to engage in hearing-protection behaviors. Method: Participants were mailed postcards that featured either a positive, negative, or neutral message on the outside of the postcard and a message encouraging hearing protection behaviors on the inside. The first posttest measurement of the effectiveness of the persuasive messages was conducted about a week after the postcards were mailed. The delayed posttest measurement was conducted six weeks later. Results: Responses from 307 coal miners revealed that the positive or neutral messages generated significantly more self-reported hearing protection behaviors than the negative message. Identical results were obtained in a delayed posttest assessment of miners' self-reported hearing protection behaviors. The positive message was also more effective than either the neutral or negative message in preventing defensive mechanisms from emerging over time. Impact on Industry: Positive and neutral messages were convincingly more than negative messages in facilitating self-reported hearing protection behaviors among coal miners. Similarly, the positive messages kept defensive processes at bay. Keywords: Hearing protection; Hearing loss; Coal miners; Campaign; Messages