Search Documents

By L. R. Burdick

The Smokescope is an instrument recently developed for determining the density of smoke by shade comparison. The instrument is designed so that the smoke is seen adjacent to two shades of gray corresponding to Nos. 2 and 3 on the Ringelmann chart. Data on smoke density are important in the smoke-abatement field. The method that is specified and accepted as standard for smoke-density determination by the majority of city smoke regulations involves comparing the smoke shade with the four shades on the Ringelmann chart as published by the Bureau of Mines.2/ This investigation was made to determine the accuracy and convenience of the Smokescope. It was conducted as a part of the Bureau I s air-pollution work, which includes the study of techniques that will promote smoke abatement. The accuracy of the Smokescope was arbitrarily defined as the difference between the Smokescope determinations and the determinations by the accepted, standard method and was expressed as Smokescope correction. Although the corrections obtained were strictly correct only for the two observers and the Smokescope of the investigation, they indicate what might be expected from any observer who uses a Smokescope with reference shades that duplicate those of the test instrument. The report is devoted largely to the data on Smokescope correction, which were taken from a single stack under controlled smoke conditions. Field work, which was done at various locations with different stacks, is mentioned briefly in connection with the comparison of the convenience of the two methods. The data for estimating Smokescope correction were taken for the three variables that were expected to affect the results, namely, the density of the smoke, the amount of light, and the color of the sky behind the smoke.

Jan 1, 1955

By Donald J. Barnes

Gold was found in samples collected from Pleistocene and Holocene stream and terrace deposits. Approximately 15,000 cu yd (11,400 cu m) of small and discontinuous terrace and stream gravel deposits in the study area are composed of material derived from sedimentary and granitic rocks. The detritus is subangular to subrounded, and poorly sorted, ranging from boulder to sand size. Gold values in samples collected averaged 8.2 cents per cu yd (gold value of $500 per oz). Pan concentrates and rock chip samples collected from reported mineralized zones showed an absence of economic minerals. Stream placer deposits are uneconomic. No potential was observed for metallic or nonmetallic minerals in the La Panza study area. No potential exists for gas, oil, or coal resources.

Jan 1, 1981

By Thomas M. Barczak

This report describes a study that examined load transfer mechanics in longwall shield supports as part of the Bureau of Mines research program to optimize support design and utilization. The objectives of this study were to determine the contribution of the leg cylinders and the caving shield-lemniscate assembly towards full shield vertical and hor-izontal load resistance capability and to determine how the interaction of these members affect overall shield response. Load-displacement characteristics of the leg cylinders and the caving shield-lemniscate assembly, independent of the full shield, were evaluated from controlled displacement tests in the Bureau's mine roof simulator and responses were compared with full shield responses to identify load transfer mechanics. It is concluded from this research that the participation of the caving shield-lemniscate assembly significantly affects the response of the shield support. It is likely that the caving shield-lemniscate assembly is not participating fully in current shield designs because of translational freedom in the numerous pin joints. It is also concluded that the shield will respond differently to different boundary condi-tions resulting from interaction with the strata. This report describes load transfer mechanics of shield supports and the implication of these research findings on shield design and utilization.

Jan 1, 1988

By A. J. Strazisar

The Bureau of Mines conducted a laboratory investigation to study the effectiveness of low-pressure steam and water spray in suppressing respirable dust at the tips of a saw-type cutting wheel. Suppression efficiencies were found to be proportional to the amount of the water or steam applied at the cutter tips. For equivalent water output rates, a maximum efficiency of approximately 80 percent was reached for both steam and water spray. Results from the steam and water spray tests showed an increase in suppression efficiency with an increase in particle size of 1 to 8 micrometers. The data indicate no advantages for using steam as a dust suppressant.

Jan 1, 1972

By L. C. IlsLey

[The service given by a flame safety lame is twofold: It provides a safe light and it gives evidence of the condition of the mine atmosphere relative to the presence of methane and the deficiency of oxygen. Since the development of portable electric mine lamps, flame safety lamps are little used for lighting but their use as detectors is as extensive and important as ever. A flame safety lamp in the hands of a trained user will definitely show methane concentrations as low as 1 percent, which in well below the lower explosive limit of methane and air. However, this does not always suffice, especially when making studies of mine ventilation, where it may be desireable to detect concentrations below 1/2 of 1 percent.]

Jan 1, 1936

By Don Steffa

Drift mining, according to California mining terminology - and it is distinctly a California development - is the blocking out and extraction (breasting) of the auriferous gravels of an ancient buried stream either through tunnels, inclines, or shafts; it is one of the minor divisions of the larger classification known as placer mining. The contribution of each of these divisions and of lode mining to the gross production of gold in California totals as follows:3 [ ] The total amount of gold recovered from the placers of California from 1848, when Marshall discovered the precious metal in the mill race at Coloma, to 1928, was $1,226,515,404. The same period saw a total gold production from all operations of $1,823,562,360.

Jan 1, 1932

By David K. Denton

There are no active mines in the Mt. Eddy RARE II area. Chromite, gold, and stone prospects were examined. The RARE II area contains no identified mineral resources; however, a sample of a 260 ton occurrence contained 38.1 percent chromium oxide (Cr203) at the Ratero Prospect (fig. 1, no. 3), which has low potential for chromium resources. The Johnson Mine (fig. 1, no. 6) produced a small unrecorded amount of chromite during World War IT, but only a low potential exists for chromium resources. A low potential exists for gold resources at the Half Century Prospect (fig. 1, no. 2). At a borrow pit northwest of the study area (fig. 1, no. 1), sheared serpentinite is quarried for road metal; similar rock occurs in the RARE II area, but better material is more readily available elsewhere. Sand and gravel occurrences are too inaccessible and distant from markets to be considered resources. Mineral fuels and geothermal resources were not evaluated during this Bureau of Mines study. There currently are three unpatented lode mining claims in the study area. INTRODUCTION The Mt. Eddy RARE II area is 7 air-mi west of Mt. Shasta City, California, and straddles the Siskiyou-Trinity county line. The roadless area includes 7,200 acres of rugged, glacially carved, ridges and drainages which comprise Mt. Eddy. Elevations vary from 6,000 ft along the North Fork Sacramento River to 9,025 ft at the summit of Mt. Eddy. The area is covered with conifer forest below 8,000 ft elevation.

Jan 1, 1983

By G. W. Reimers

Metastable pyrophoric wüstite (FexO, with x between 0.89 and 0.95) was found to be much easier to grind to colloidal state than were its stable disproportion products magnetite or iron. The grinding of polycrystalline magnetite appears to be complicated by the magnetic flocculation arising from interparticle attraction. This is superimposed on the attraction of a fluctuating electric dipole for a neighboring induced dipole. More than 85 pct of the tumbling time was saved by grinding antiferromagnetic wüstite instead of the ferrimagnetic oxide of iron (Fe304). Disproportionation of colloidal wüstite to the stable ferromagnetic and ferrimagnetic colloidal particles of alpha-iron and magnetite, respectively, was accomplished rapidly at temperatures above 250° C but below 570° C, the eutectoidal stability point of the wüstite phase.

Jan 1, 1972

By K. Kar, M. Gautam, J. T. Jurewicz

The 10-mm Dorr-Oliver cyclone has been widely used as a personal sampler for size selective sampling of particles within the respirable range (Dp < 10 gm). Because of their inertia, the particles are unable to follow the swirling flow (outer vortex) within the cyclone. The particles migrate to the bottom of the cyclone, depending on their size, and get trapped into the inner vortex which leads to an eventual blow-off from the top of the cyclone. By measuring the size distribution of the particles in the free stream and in the collected sample, the aspiration efficiency of the cyclone can be calculated. Velocity difference between the free stream and sampling velocity. Inlet orientation, particle impaction and deposition, particle inertia and free stream turbulence result in the departure of the aspiration efficiency from unity and this, in turn, leads to inlet bias. Although the effect of inlet bias on sampling efficiency has been investigated in past, the results lack detailed information and show only some general trend. In this effort, a systematic, in-depth experimental work on the effect of inlet bias on the sampling efficiency has been undertaken using non-intrusive Laser Doppler Anemometry (LDA), Aerodynamic Particle Sizer (APS) and impactors.

Mar 1, 1992

By G. S. Rice

The recommendations of the Bureau of Mines on rock dusting practices are embodied, except in a few details, in the Recommended American Practice for Rock-Dusting Coal Mines to Prevent Coal-Dust Explosions, approved by the American Engineering Standards Committee. December 30, 1925. It is specified that the dust to be used is of a elm that all will pass through a sieve having 20 meshes per linear inch and that 50 per cent or more will pass through a sieve having 200 meshes per linear inch. Thus the coarsest size of dust and the minimum proportion of fine dust are specified, but the specification does not indicate whether a larger proportion of fine dust would be desirable. There have been advocates of the use of that size of rock dust of which the particles would all approach 200-mesh in fineness. Explosion tests were made in the Experimental mine in the earlier period of testing which indicated that the finer rock dust is somewhat more effective under test conditions, but not sufficiently so to Justify the cost of finer grinding of the dust; also there are some disadvantages of finer dust described hereafter.

Jan 1, 1930

By Liming Yuan

In order to reduce fire hazards caused by spontaneous combustion in longwall gob areas, a computational fluid dynamics (CFD) study is being conducted by National Institute for Occupational Safety and Health (NIOSH) to simulate the spontaneous heating of coal in longwall gob areas. A CFD model was first developed to model the spontaneous heating process in a two longwall panel district using a bleeder ventilation system with a stationary longwall face. The spontaneous heating is modeled as the low-temperature oxidation of coal in the gob using kinetic data obtained from previous laboratory-scale spontaneous combustion studies. Heat generated from coal oxidation is dissipated by convection and conduction, while oxygen and oxidation products are transported by convection and diffusion. CFD simulations were then conducted to model the spontaneous heating in longwall gob area with a bleederless ventilation system. A single longwall panel with a bleederless ventilation system was simulated. The effect of gob permeability on the spontaneous heating was also investigated.

Jan 1, 2009

By A. F. Colombo

The differences in starch demands that occur between ore types subjected to the anionic flotation of calcium-activated gangue and the range of residual starch contents expected to give the best metallurgical response were evaluated on a batch and pilot plant basis. A phenol-sulfuric acid procedure was used to determine the residual starch contents in the iron ore slurries. Three pilot plant campaigns on samples from a group of orebodies located on the Marquette Range, Michigan, showed that in the rougher flotation pulp, a residual carbohydrate range of 25 to 100 ppm, which is equivalent to a 0.5 lb/short ton spread, yielded optimum results. Concentrates assaying at least 65 percent Fe and less than 6.0 percent Si02 and containing more than 80 per-cent of the recoverable iron were obtained. Both batch and continuous research indicated that starch adsorption is calcium modulated and relatively unaffected by the fatty acid additions employed. Residual starch level is not a critical control factor, but the addition must be adjusted to about 25 to 50 ppm residual starch and kept in this range for most effective utilization of the added tapioca flour.

Jan 1, 1972

By LB. Berger

"INTRODUCTION The use of gasoline engines as the motive power for lift trucks, tractors, and other types of mobile equipment operated in enclosed spaces, such as industrial plants and warehouses, may create a hazard because of the carbon monoxide present in the exhaust gases of the engines; gasoline-powered equipment should not be used in mines or tunnels. Because the equipment is mobile, local ventilation usually is impracticable, and general ventilation of the spaces is nec-essary to dilute and remove the carbon monoxide. To estimate the rate of ventilation required in such situations, information is necessary on the concentration of carbon monoxide in the exhaust gas and the rate at which exhaust gas is produced under given operating conditions. The purpose of this paper is to present data that may be used in making estimates of ventilation requirements.COMPOSITION OF GASOLINE-ENGINE EXHAUST GASThe exhaust gas of a gasoline engine consists mainly of carbon dioxide, carbon monoxide, hydrogen, oxygen, and unburned hydrocarbons (usually reported as methane), together with the nitrogen present as a residue from the air sup-plied for combustion. 3/ The exhaust also contains water vapor resulting from combustion of the hydrogen of the fuel. The water-vapor content is not included in exhaust-gas analyses calculated on a ""dry"" basis and is not involved in the estimation of ventilation requirements."

Jun 1, 1947

By Thomas E. Marshall, Patrick A. Kinek, Gerald L. Finfinger

The purpose of this investigation was to evaluate the integrity of the existing shutoff valves and actuators used under high-temperature conditions in the Bureau of Mines&apos; horizontal borehole methane drainage pipe- line system and to determine the potential for improvement in the system. In the field tests, both fire-safe ball valves and standard brass ball valves were initially subjected to a 30-min pan fire without thermal protection. Neither valve could maintain line pressure beyond 11 min in a fire that reached temperatures between 500° and 700° C. Based on the test results, it was concluded that the brass ball valve used in the Bureau&apos;s methane drainage pipeline system can be retrofitted with an inexpensive "fire bag" to substantially increase its integrity under mine fire conditions.

Jan 1, 1986

By Daryl E. Radcliffe

This report describes an instrument system developed by the Bureau of Mines to continuously monitor and record changes in roof displacement during underground mining activity. The instrument consists of a single-wire extensometer coupled to a mechanical-drive chart recorder mounted in an aluminum frame installed in the roof. The unit is small and simple to install and meets safety requirements for use in underground coal mines.

Jan 1, 1977

By A. W. Fahrenwald, W. W. Staley

"In flotation concentration, various machines are employed for agitation and aeration of the ore pulp in the operation of frothing. The power required in the operation of these machines varies considerably with the type and make of machine used. The object of this investigation was to determine the effect of certain physical properties of the pulp particularly viscosity, density, and temperature - upon the power required by certain forms of pulp agitators.The viscosity factor is most involved because it is affected by temperature and by density. Viscosity of liquids and suspensions has been extensively studied and the physics and mathematics of the subject are much enlarged upon in books and in the literature. It is not, however, the intention of this study to become involved in the intricacies of these phases of the subject.The agitation of the various mediums in the experimental work did not last long enough to cause a measurable rise in temperature from the ""beating"" of the medium, hence no cognizance is taken of this factor.No attempt has been made to correlate the data obtained with the impeller with any information regarding centrifugal pumps. The object sought here is quite foreign to the problems of pumping. The impellers used are ""open"" and air is involved.The experiments performed and the data obtained are presented. Only that amount of discussion necessary to make the results understandable is given.Tap water was used in all experiments. A comparison of distilled water and tap water showed no measurable difference. In the experiment in which sodium chloride was needed, the commercial salt as used in fire assaying was taken. The quartz was of the ""bull quartz"" variety, thoroughly washed free of iron oxide."

Jun 1, 1930

By G. L. Oldright, Virgil Miller

"INTRODUCTION The first ten papers of the series on smelting in the lead blast furnace described the operation at the custom smelter of the International Smelting Co., Tooele, Utah, and at the plant of the Bunker Hill Smelting Co., Kellogg, Idaho, which handled a very rich lead concentrate. These previous papers may be considered a picture of the traditional lead smelter treating custom ores and of the smelter that will treat the type of product likely to be made in the future - lead concentrates of an increasingly rich grade.The great plant at Trail is of special interest to those smelting lead products containing much zinc and faced with the necessity of transforming all of their byproducts into commodities which may be sold profitably. The plant is equipped to produce electrolytic zinc, lead, copper, silver, bismuth, and cadmium. Part of the sulphur evolved from treating the ores is converted into sulphuric acid. Complete fertilizers for agricultural purposes are also produced.The smelter of lead ores has long considered that zinc is one of the most difficult ingredients that he has to handle. Even with the gretat improvement in flotation practice today, the residues from electrolytic zinc plants leaching zinc concentrates must still be smelted for their lead content. Of the total gangue material not separated from the lead concentrate sent to the smelter, zinc is still one of the most notable in percentage. The most successful way of coordinating the over-all operations of a concentrator, an electrolytic zinc plant, and a smelter provided with a plant for re-treating the blast-furnace slag for its lead and zinc content must be of interest to many treating complex ores.ACKNOWLEDGMENTThe data in this paper were collected in cooperation with the Consolidated Mining & Smelting Co. of Canada, Limited, and its entire technical staff. Detailed acknowledgments of assistance received are given in the papers from which this one is briefed."

Sep 1, 1934

By E. D. Gardner

The Bureau of nines, in cooperation with the mining companies of the Southwest, is conducting an investigating to ascertain the safest and most economical explosives to use in metal mines, and to ascertain the best methods of blasting under various conditions. A part of this investigation has been a study of drilling and blasting drift rounds in metal mines. This paper covers one phase of work on drift rounds and discusses the methods of loading the individual holes of the rounds. The blasting tests, on which this paper is based, were made at the Copper queen Branch of the Phelps Dodge Corporation at Bisbee, Arizona.

Jan 1, 1927

By A. W. Deurbrouck

This report presents the results of a washability study of 322 coal mine samples showing the sulfur forms and distribution in the coals. The samples were collected from mines which were principally utility coal producers. Generally, the data show the total sulfur content of the coals evaluated could be significantly reduced by some combination of stage crushing and specific gravity separation. However, few coals could be upgraded to a final product containing 1 percent or less total sulfur. The complete washability data are presented for each sample processed. A statistical evaluation is included for the coalbeds from which more than 10 samples were collected and for the geographical coal producing regions. A graphical summation is presented for the coal producing regions and selected coalbeds.

Jan 1, 1972

By Daryl E. Radcliffe

The Bureau of Mines studied the displacement of the roof in a portion of the Bear coal mine near Somerset, Colo, Horizontal-and vertical-displacement gages were installed in a five-entry section during normal room-and-pillar mining procedures. Monitoring of the roof continued until this section was mined out. Displacement measurements in combination with known time lapses between mining and bolting operations indicate that once support is achieved, the length of unsupported time does not appear to affect long-term roof stability in the mine under investigation.

Jan 1, 1978