Search Documents

Improve the performance of waterjet nozzles used for water-jet-assisted cutting to optimize rock cutting efficiency. Approach The performance of a longwall shearer equipped for water-jet-assisted cutting was evaluated during an earlier study (Tech News No. 277). Waterjet nozzles were used to direct the solid streams of water that impacted the rock near the tip bits. The maximum water pressure that could be delivered to the nozzles was about 6,000 psi. Due to the "break up" of the solid stream of water, some of this pressure was lost before the water reached the rock. The pressure could have been increased by moving the nozzle closer to the bit tip but) moving the nozzle too close increases the possibility of damage to the nozzle. Study Results A test apparatus was built to measure water pressure at the location of water jet impact (see illustration). The target, a tungsten carbide plate with a 0.013 inch diameter orifice, was placed at the location of water jet impact. A pressure transducer, used to monitor impact water pressure, was positioned under the plate. Water pressure at the nozzle was maintained at 6,000 psi. The distance between the nozzle and target was varied from 2 to 5 inches.

Jan 1, 1988

By F. W. Richard

This paper describing the mining practices at the Ground Hog Unit of the Asarco Mining Co., a subsidiary of the American Smelting and Refining Co., is one of a series being prepared by the United States Bureau of Mines on mining methods, practices, and costs in the various mining districts of the United Stated. The Ground Hog mine is at Vanadium in the Central mining district, Grant County, N. Mex., about 1.0 miles east of Silver City and 2 ½ miles southwest of Santa Rita. A branch line of the Atchison, Topeka & Santa Fe Railway connects Vanadium with Deming, about 45 miles southeast.

Jan 1, 1930

By Oliver Bowels

Many inquiries are received by the United States Bureau of Mines for the names of elementary books on geology, mineralogy, methods of identifying minerals, prospecting, and similar subjects. In response to this demand the following brief bibliography has been prepared. As many of the inquiries are received from those who have limited technical knowledge of the subjects involved, the bibliography includes the simpler texts which present the subjects in nontechnical language. Other texts contain glossaries which define the technical terms used. A short note following the title indicates the character of each book, the number of pages, and the price. Thus, elementary mineralogists or geologists, prospectors, mineral collectors, nature students, or travellers may select the texts that best suit their requirements and their capabilities. To supply the needs of more advanced students, quite a number of the standard texts used in schools and colleges are included in a second group. A short list of books on economic geology and mineralogy has also been added.

Jan 1, 1929

By P. A. Surgeon, R. R. Sayers

It is not the purpose of this report to try to describe all the work done during the past year for the improvement of health or the prevention of illness among miners , but to call attention to a few of the more outstanding investigations in which progress has been made . Among these , the investigations on the physiological effects of carbon monoxide , dust and ventilation , and temperature and humidity will be discussed . Carbon Monoxide . During the years 1920 and 1921 , much more work has been done on the various A survey phases of carbon monoxide than has been carried on for a number of years . of carbon monoxide poisoning in the American steel works , metal mines , and coal He conmines was made by Dr. Henry S. Forbes , of the Harvard Medical School . ** cludes from his survey that late after- symptoms following acute severe gassing rarely occur , and that almost always there is evidence of pre - existing pathological conditions when such effects do appear . He further states that he found no evidence of cumulative harmful effects resulting from frequent exposure . Dr. Forbes , Dr. Forbes , assisted by Louise Hompe , made a laboratory investigation in which anesthetized animals were exposed to carbon monoxide , illuminating gas , and benzol *** . The investigators conclude that , under the conditions of their experiments , there is no change in the coagulation time of the blood . It has been stated by many investigators that the blood of those affected by carbon monoxide does not clot as quickly as normal blood . While the investigation referred to above may not cover all the conditions , it is a valuable contribution to the subject as it indicates that the small hemorrhages found in the membranes covering the central nervous system , abdominal organs , etc. , at autopsy of those dying of carbon monoxide poisoning is probably not due to direct toxic action of the gas upon the blood .

Feb 1, 1922

By C. M. Bouton

Although much valuable work has been done in the study of dust explosions, the laboratory technique has not been developed to the point where the many factors involved can be properly controlled, and thus where really fundamental information can be obtained. This paper presents a brief discussion of the difficulties encountered in fundamental work on dust explosions, a description of apparatus intended, to overcome some of them, and an account of some results obtained. FACTORS INVOLVED IN DUST EXPLOSIONS The more important factors pertaining to the dust cloud itself which are known to determine the phenomena of explosions are (1) the kind of dust; (2) its fineness; (3) its concentration in the exploding cloud; and (4) the nature of the interior motions, or turbulence, of the cloud before and during the explosion. These factors are arranged in what seems to be an ascending order of complexity. The kind of dust is the factor most easily subject to control. The fineness of the dust at first sight seems to be a controllable factor, but when it is recalled [that] most explosible dusts are mixtures of particles of continuously varying sizes so small as to pass through the finest woven sieves, and therefore difficult to separate either for purposes of analysis or experiment, the fineness is seen to be a factor difficult to control accurately.

Jan 1, 1929

By John C. Edwards

The Bureau of Mines has developed a time-dependent mathematical model of radiative heating of bulkheads in mines. The model includes both reradiation from the duct (cylindrical) walls and direct radiation from the fire zone. Thermal loss into the wall of the duct and into the bulkhead is included. Both brick and wood bulkheads are considered. It is found that the heating rate of the system scales as the duct length-to-diameter ratio and the flame temperature. In particular, the time required for the irradiated surface of the bulkhead to reach a specified temperature decreases with increasing flame temperature for a fixed length-to-diameter ratio and increases with increasing length-to-diameter ratio for a specified flame temperature. It is also deter-mined that the time, T, for the bulkhead surface temperature to reach a specific value, Tb, for a fixed length-to-diameter ratio less than 4 and for a flame temperature of 1,200 K is approximately linearly dependent on Tb for 500 K < Tb < 700 K, and is nearly exponentially dependent on the length-to-diameter ratio for Tb = 600 and 700 K.

Jan 1, 1979

By Kris Chatrathi, John E. Going, Kenneth L. Cashdollar

Two types of flammability limits have been measured for various dusts in the Fike 1-m3 (1000-L) chamber and in the Pittsburgh Research Laboratory (PRL) 20-L chamber. The first limit is the minimum explosible concentration (MEC), which was measured at several ignition energies. In addition to the three dusts studied previously (bituminous coal, anthracite coal, and gilsonite), this work continues the effort by adding three additional dusts: RoRo93, lycopodium, and iron powder. These materials were chosen to extend the testing to non-coal materials as well as to a metallic dust. The new MEC data corroborate the previous observations that very strong ignitors can overdrive the ignition in the smaller 20-L chamber. Recommendations are given in regard to appropriate ignition energies to be used in the two chambers. The study also considered the other limiting component, oxygen. Limiting oxygen concentration (LOC) testing was performed in the same 20-L and 1-m3 vessels for gilsonite, bituminous coal, RoRo93, and aluminum dusts. The objective was to establish the protocol for testing at different volumes. A limited investigation was made into overdriving in the 20-L vessel. The LOC results tended to show slightly lower results for the smaller test volume. The results indicated that overdriving could occur and that ignition energies of 2.5 kJ in the 20-L vessel would yield comparable results to those in the 1- m3 vessel using 10.0 kJ. The studies also illustrate the importance of dust concentration on LOC determinations.

Develop a training program to help mine workers effectively fight small fires in underground Goal mines. Training would enable miners to make rapid judgments on whether to attempt extinguishment, and how best to use the firefighting equipment on hand. Approach Fire reports were analyzed to define and delineate physical and behavioral variables which affect firefighting activities, and to determine effective procedures for extinguishing small fires. A course was then designed to train miners in such procedures. Finally, the course was reviewed by industry experts and administered to a group of miners to determine needed revisions and to validate the course. How It Works Analysis of fire data showed that six items should be emphasized in teaching proper fire response: 1. Alertness to fire potential. 2. Immediate power cutoff. 3. Internal, external communication. 4. Teamwork in fighting fires. 5. Role of ventilation and position of men inby the fresh air side. 6. Effective use of fire suppressant materials.

Jan 1, 1983

By V. A. Marple, K. L. Rubow, B. A. Olson

"A virtual impactor personal aerosol sampler (VIPAS) bas been developed for use in diesel-equipped mines to collect size-separated samples or diesel exhaust and mine dust particles in the respirable size range. This sampler consists or three stages: a 10-mm cyclone, a 0.8- µm cutpoint virtual impactor and two filter cassettes. The large non-respirable particles are removed in a 10-mm cyclone. The respirable particles from the cyclone pass through a 0.8- µm cutpoint virtual impactor with the particles larger than and smaller than 0.8 JI.ID (mine dust and diesel exhaust particles, respectively) collected on two 37-mm filter cassettes. The sampling How rate is 2 L/min so as to be compatible with the standard respirable dust sampler and personal sampling pumps. INTRODUCTIONThe mining industry has been increasing its use of diesel-powered equipment in underground mines, especially in coal mines. With this increased usage has come an increased concern regarding the health effects associated with inhaling diesel exhaust particles since they are in the respirable particulate size range. A Mine Safety and Health Administration (MSHA) advisory committee directed MSHA to develop a sampling protocol for diesel exhaust particles to assess worker exposure (MSHA, 1988). In addition, the National Institute for Occupational Safety and Health (NIOSH) has recommended that ""whole diesel exhaust be regarded as a potential occupational carcinogen as defined in the Cancer Policy of Occupational Safety and Health Administration"" (NIOSH, 1988).Past work, with cascade impactors in both the laboratory and in underground coal mine studies, has shown that the diesel exhaust particles are primarily in the less than 0.8 µm aerodynamic diameter size range whereas the coal dust particles are primarily greater than 0.8 µm (Marple et al., 1986; Cantrell, 1987; Rubow and Marple, 1988; Rubow et al., 1990a, b; Cantrell and Rubow, 1991). This work has been jointly performed by the University of Minnesota and Bureau of Mines researchers over the last 8 years. Typical particle size distributions for a diesel-equipped coal mine and an all electric coal mine are shown in Figure l. Note that the particles in the < 0.8-µ.m mode are the diesel exhaust particles (seen only in diesel-powered mines) and the particles in the > 0.8-µ.m mode are coal particles (seen in both the electric-powered and diesel-powered coal mines). Chemical mass balance analysis was also performed on these two size fractions to determine the degree of particle cross-contamination in the two modes. This analysis showed less than 10% cross-contamination, i.e., in coal mines Jess than 10% of the diesel exhaust particulate was collected in the coarse fraction and Jess than 10% of the mine dust was collected in the fine fraction (Cantrell, 1987; Rubow et al., 1990a)."

Dec 1, 1996

Control dust generated during mining in salt mines. Approach A machine-mounted exhaust ventilation system which moves with the cutting machine from place to place was developed. The system captures the dust at the face of the heading and exhausts it downstream of the heading in the crosscut. This helps cause fresh air from the crosscut to flow over the machine operator&apos;s position, and aids in keeping the dust cloud close to the face. How It Works The system consists of (1) a circular intake hood with a 10-inch slot extending 250 degrees around the base, bolted to the gearhead; (2) 20-inch-diameter wire-wound flexible ducting to connect the intake hood to the fan (25 ft. is allowed sufficient slack for bar movement); (3) an industrial exhaust fan capable of generating 10,000 cfm with 13 inches water gage pressure at 1435 rpm; and (4) 150 ft. of collapsible 24-inch tubing for the exhaust duct which is de-played and returned In each heading by the cutter operator and/or his helper.

Jan 1, 1983

By R. L. Handy

The goal of this research was to adapt the highly successful rock borehole shear test for use in deep, small-diameter boreholes. Operating somewhat on the principle of a rock bolt, the borehole shear test measures both the expansion pressure and pulling force to give discrete measures of rock shearing strength as a function of the applied normal pressure. A new instrument was designed and built to fit into a 2-3/8 inch diameter hole. Unfortunately the design became so complicated, the operation is nut reliable. This is attributed to constraints of the small hole, and added requirements of an in-hole anchor to push against, and a rotating shear plate cleaner for repeated tests down-hole. A clue to the d: vice complexity is its length, which is over 10 feet. Furthermore it employs concentric cylinders and one hydraulic cylinder bored into the piston of another, or it would be even longer. Meanwhile drilling technology has advanced to greatly reduce costs of drilling 5- or 6-inch diameter holes. The downhole tester therefore should be redesigned and simplified for use in a larger diameter drill hole.

Jan 1, 1982

By J. W. JOYCE

The Geophysical section of the United States Bureau of Mines has received many inquiries regarding the application of geophysical methods to the location of small, buried metallic objects. The object of this paper is fourfold: (1) To sketch as briefly and non- technically as possible the principles underlying the operation of several elec- trical geophysical methods of prospecting applicable to the finding of small, buried metallic objects; (2) to point out the possibilities and limitations of these methods; (3) to present, whenever possible, data showing actual results obtained from their use; and (4) to enumerate and describe methods that lack scientific background or foundation.

Oct 1, 1935

By W. A. Cole

As the mines get older and the active workings get Farther and farther away from the original mine openings, it becomes increasingly difficult and expensive to ventilate most coal-mines properly. At the same time, the avenues of escape for those employed underground have become so extended&apos; as often to make it impossible for them to make their way out of the mine in the event of a fire, mine explosion, or other emergency. Where such Conditions exist, the only satisfactory solution is to make new ventilation and emergency-escape openings near the active mine workings. At most mines this would necessitate sinking shafts, which is often slow and expensive.

Jan 1, 1945

By R. K. Koch

In seeking substitutes for such critical metals as chromium, cobalt, and nickel, the Bureau of Mines investigated techniques for shape-casting titanium in rammed sand molds. Castings were made in olivine, garnet, chromite, and, for comparison, zircon. It was found that commercial-grade castings up to 31 lb (maximum capacity of furnace) could be made in zircon or olivine molds if a zirconia mold wash was used. Castings up to 4 lb could be made in chromite molds, but heavier castings suffered from some mold-metal reaction. Garnet molds were found to be unsatisfactory for castings of all sizes because of gas blows and rough surfaces. In other tests shell castings of acceptable quality were produced in water-glass-bonded zircon and olivine molds up to weights of 8 lb, but chromite molds were unsatisfactory because rough casting surfaces were caused by mold-metal reaction. Unlike the currently used commercial processes, neither the rammed-sand nor the shell-molding processes developed by the Bureau of Mines generate noxious fumes at any step.

Jan 1, 1980

By C. L. Chaney

Investigations were conducted to develop spectrochemical methods capable of determining 0.01 to 100 micrograms of metals in 50 milliliters of solution. The use of gallium hydroxide (Ga(OH)3) as a carrier-precipitant to concentrate metallic ions is described. A porous-cup graphite electrode is used to collect the precipitate. A specially designed plunger permits the electrode assembly to serve as the sample-containing electrode in the subsequent spec-trographic analysis. Analytical curves are presented for antimony, arsenic, beryllium, and zinc. Sensitivities of detection are given for 13 elements. The techniques were applied to identify impurities separated from tungsten, to determine trace impurities in solutions containing high concentrations of magnesium, cobalt, or nickel, and to identify trace impurities in hydrofluoric acid. Laboratory glassware was a serious source of contamination when low levels of zinc were determined.

Jan 1, 1963

By H. H. Schrenk

The safe use of a refrigerant or any substance depends on knowledge of its pertinent properties and conditions of use; therefore some of the properties of refrigerants that are related to life, fire, and explosion hazards are discussed herein. These data serve as a basis for suggested control measures in the use· of refrigerants. The properties of refrigerants may be broadly classified into three main groups: (1) Those important for refrigeration, (2) those significant from the standpoint of confining the refrigerant, and (3) those that become important if the refrigerant escapes from the :machine or container. The first group of properties, such as latent heat of vaporization, specific heat of vapor, specific heat of liquid, etc., is not considered to be directly related to safety and is not discussed here. The second group, those properties important in confining the refrigerants, has particular significance because· it relates to "built-in" safety. This group is emphasized because it is believed the soundest procedure in designing equipment is to give due consideration .to both the health and safety hazards likely to be associated with the equipment. Furthermore, the toxicity, fire, and explosion hazards are controlled as long as the refrigerant is confined. Some properties of this group are (1) stability, (2) corrosiveness, (3) boiling point, (4) pressure developed in the system, (5) warning odor or irritation, and (6) ease of detection. The third group includes such properties as toxicity (of compound and decomposition products), irritating action, and explosibility.

Feb 1, 1942

By Joseph Cervik, Gerald L. Finfinger

The Bureau of Mines conducted an experimental degasification project in Island Creek Coal Co.&apos;s Virginia Pocahontas No. 5 mine. Methane from the over- lying Pocahontas No. 4 coalbed was entering mine workings in the Pocahontas No. 3 coalbed through fractures in the roof rock. Small-diameter (1-5/8-inch) holes were drilled into the overlying coalbed to reduce the gas pressure and intercept methane flows, which were piped to the surface through an under- ground 6-inch-diam steel pipeline. The total methane flow rate from the vertical holes averaged 150,000 ft3/day for the first month. Methane flows into the mine were reduced by 47 pct, thereby demonstrating the effectiveness of this form of degasification in reducing ventilation requirements and providing a safer working environment.

Jan 1, 1979

By D. G. RUNNER

Information Circular 6148R, " Selected Bibliography of Minerals and Their Identification ," was issued in June 1929 , revised in July 1937, and again in October 1938. The popularity of this circular , combined with the desire to make it more comprehensive , has occasioned the preparation of this compilation of references . Where possible , date of publication , publisher, current price , and number of pages are given, although prices are subject to change at intervals . The references are grouped under the following headings : minerals , gems , rocks , geology, geomorphology, engineering geology , prospecting, mining . engineering, microscopy, technical dictionaries , and miscellaneous . For ready reference, the authors ' names are arranged alphabetically under each grouping . This list is not comprehensive, but contains only those references in most common use and which are generally available in public college libraries .

Sep 1, 1949

By Kenneth M. Earl

The purpose of this investigation was to obtain subsurface information on the John Burdette barite-fluorite deposit, Garrard County, Ky. The deposit was intersected in each of five inclined diamond-drill hales aggregating 1,163 feet. All holes were drilled from the hanging wall of the deposit; the inclinations varied from minus 41° to minus 75°. Disseminated metallic sulfides were noted in the drill cores from holes 1, 2, 4, and 5. The deepest drilling was hole 5, which intersected the deposit at approximately 490 feet down dip. Visual inspection of the cores did not indicate mineralization of economic importance; therefore, no chemical analyses were conducted. Condensed logs of diamond-drill cores are included in this report. All drill cores were shipped to the Bureau of Mines core library in Minneapolis, Minn., for future reference,

Jan 1, 1959

By B. J. Scheiner

A ferrous chloride-oxygen leaching system was investigated by the Federal Bureau of Mines to determine its effectiveness for recovering copper and silver from a tetrahedrite concentrate that had been pretreated to remove a majority of the antimony. The pretreated concentrate contained coppers, silver, lead, zinc, antimony, and arsenic. Parameters affecting metal extraction (such as temperature, pressure, amount of ferrous chloride, and initial hydro-gen ion concentration) were studied. Copper extraction of 98 pct was achieved by leaching 4 hours at 40 pounds per square inch gage (psig) and 100° C. Copper was recovered from leach solutions by cementation with iron, and the resulting ferrous chloride was recycled. Leaching the residue with cyanide followed by electrowinning recovered 99.7 pct of the silver. Iron, antimony, arsenic, and sulfur reported to the tailings.

Jan 1, 1978