Search Documents

By L. H. Johnson

"INTRODUCTION The Pennsylvania anthracite industry produced 53 million net tons of anthracite during 1945. Fifty-one million tons was prepared for the commercial market (3), 3/ and 2 million tons (consisting of fine sizes) was used for colliery power consumption. Of the number of tons prepared for market, 17 million tons (33 1/3 percent) was prepared by the use of acid mine water treated with lime.Mine water from underground workings is pumped, drained, and stored in huge quantities. The mine-drainage systems in the anthracite region handle over 200 billion gallons of water annually, of which 150 billion gallons is pumped to the surface. More than 69 billion gallons of water is impounded in underground pools (1). Much of this water is employed for breaker use, dust-control installations; hydraulic backfilling, combatting mine fires; and aiding in the transportation of anthracite in gently dipping places where sheet iron is used Roos(4) estimates that 1,100 gallons of mine water is utilized in the preparation of anthracite mined."

Nov 1, 1946

By Frank D. Lamb

Pyrophyllite, a hydrous aluminum silicate (Al2 Si4O10 (OH)2 ) has been mined in North Carolina and marketed without beneficiation for the past 100 years, but recent demands for higher-grade material indicate that an economical concentration method is needed for at least a part of the pyrophyllite production. Past production has depended upon selective mining and hand sorting, which is often unsatisfactory because of the finely disseminated character of the ores. The major impurity in North Carolina pyrophyllite ores is quartz, which accounts for the abrasiveness of the commercial product. Since pyrophyllite is only slightly heavier than quartz, those ores cannot be beneficiated by simple gravity-concentration methods. Some separation can be attained by differential grinding and air classification because of the difference in hardness of the two minerals) but the separation is not sharp. Froth flotation of pyrophyllite from Quartz has never been attempted commercially, but if the demand for high-grade material is sufficient, it would seem that this process offers the most premise of being economically feasible.

Jan 1, 1950

By Alfred E. Schwaneke

A versatile torsion creep tester was instrumented with electromechanical and servomechanical components to operate automatically and unattended, producing digital printed outputs. The apparatus uses an electrical system for applying torsional stresses, and a unique angular transducer as a null detector operating a servocontrolled strain measuring system with the digital readout. The tester is designed to measure the creep in single-crystal or polycrystalline zinc, zinc alloys, magnesium, magnesium alloys, or other metals and alloys. Applied stresses may be varied from zero up to 2,000 psi in the outermost fibers of a 1/8-inch-diameter, 4-inch-long specimen. Strain readings to 0.001 degree, equivalent to a strain of 2.73 X 10-7, may be made automatically from one every 5 seconds to one per month. The apparatus has provisions for programed temperature control and special atmospheres or vacuum operation. A discussion of applications of the system to other mechanical testing apparatus is included.

Jan 1, 1970

By J. M. Stuve

Heat of solution measurements of high-purity neodymium metal and neodymium trichloride (NdCls) in 4.360 molal hydrochloric acid (HCI) were used to determine the standard heat of formation (6EPr) of NdCls? From solution data obtained, the heat of formation of NdCls (c) was computed as -248,970 ±260 cal/mole at 298.150 K.

Jan 1, 1965

By Oliver Bowles, J. E. Crawshow

A line of cordeau detonating fuse was placed in hole No. 2, no electric detonators being used in the hole. After 12 or 13 cases of 40 per cent nitro starch powder had been poured into the hole in loose form, it was found that a space of only 17 ft. remained for stemming. It was decided that space for an additional case of powder might be obtained by tamping the charge. The tamping was done with a heavy plunger, about 3 or 3 inches in diameter and 10 inches long, made of lead with an iron core with an iron eye in the top to which a 3/4 inch rope was attached, and weighing between 30 and 40 pounds. This weight was intended for use in sinking explosive in wet holes, and not for tamping. It is estimated that the tamping had continued at least 10 The quarry superintendent had gone a considerable distance for a box of powder, returned, and reached a point about 10 feet from the hole, minutes.

May 1, 1920

Mining machine cabs were built to comfortably fit 90 percent of adult American males, and have controls that allow fast natural reactions during emergencies. These cabs and controls also fit 40 percent of the adult female population in the United States. The operators are also positioned for good visibility and for protection from roofing and ribbing hazards. Two basic designs were developed, one for seam heights on the order of 4 feet I and the second for seam heights near 8 feet. The sitting position of the largest person within the sample size group (termed a "95th percentile man") determined the basic cab shapes. The size of different parts of the human body and how they work together I established other design features of the cab. Areas of visibility, limits of operator movement, comfortable seating angles, etc., were carefully identified for the largest and the smallest persons within the sample size group. Placement of controls was based on these findings. The controls are designed and placed to allow operation with minimum physical strain and fatigue. See chart on other side of sheet.

Jan 1, 1978

By J. P. Rider

Average production from longwall mining operations in the United States has risen from approximately 800 tons per shift in 1980 to over 4,600 metric tons per shift in 1999. Such a large increase in production has the potential to generate significantly more dust. Previous NIOSH research has shown that, on average, respirable dust levels generated by the shearer accounts for 50% of the airborne dust generated during longwall mining. Ventilating air and water are primary controls being used in an effort to reduce longwall dust levels. Longwall operators are applying more air and water than ever before and have expressed concern over reaching maximum practical limits for these controls. Full-scale laboratory tests are being conducted to evaluate the impact on shearer-generated dust levels for changes in face air velocity, water quantity at the shearer, water spray pressure, spray system design, mining height and cutting direction. Results of this research should identify the most appropriate control levels for various operating conditions. In addition, general recommended dust control practices for longwall mining will be discussed. KEYWORDS Longwall, coal dust

Apr 1, 1975

By J. B. Gayle

Because economic and geographic factors have focused particular attention on the use of anthrafines in blends containing Lower Kittanning coal as the low-volatile component, samples from this particular bed were selected for experimentation whenever practical. Carbonizing tests were carried out in accordance with standard procedures, using the Tuscaloosa and sole-heated ovens. Most of the results are in general agreement with those reported by previous investigators. Specific findings are as follows: (1) The effectiveness of anthrafines in reducing coal expansion is such that even highly expanding, low-volatile coals can be carbonized safely with suitable additions of anthrafines and careful control of charge density. (2) Increases in coke size, resistance to shatter, and apparent specific gravity appear to be characteristic for additions up to approximately 15 percent to a fixed base blend. When anthracite of minus-48-mesh size was used and the proportion of low-volatile coal simultaneously increased, these indexes increased only slightly or remained substantially constant. (3) No increase in breeze formation was noted for additions in amounts up to 15 percent. (4) Abradability of coke was increased by additions of anthracite of No. 5 Buckwheat size, but it either decreased or remained sub¬stantially constant when the inert was ground to pass a 48-mesh screen.

Jan 1, 1956

To cost-effectively reduce noise and vibration in newly manufactured mantrip vehicles. Approach Previous Bureau of Mines research demonstrated that noise controls could be in-stalled on existing mantrip vehicles, thereby substantially lowering noise levels inside the mantrip. Under Bureau sponsorship, a manufacturer of mantrip vehicles agreed to incorporate similar noise controls into a new vehicle during manufacture. Throughout this project, durability, maintainability, and cost were considered to be as important as noise reduction. How It Works The following noise-control features were included in the new mantrip: (a) Suspension Isolation- The suspension components were isolated by inserting elastomeric materials between them and the vehicle frame.

Jan 1, 1982

By C. E. Reistle

[In producing crude oils of paraffin base and of mixed base the producer is often confronted with the problem of preventing and removing paraffin that settles out of oil and accumulates in the well. This paraffin consists of heavy waxes with some sand and asphalt, and varies in. consistency from a soft semifluid wax to hard gummy wax. This problem is by no means a new one as troubles have been encountered with it since the earliest days of the industry. However, with the discovery of the panhandle, Texas, field and other large fields in which extensive troubles have been encountered, the problem has assumed added importance. In new fields the most serious trouble with paraffin is in the flowing wells the paraffin accumulates in the casing and tubing of such wells and unless removed will completely plug the well. This condition also develops in wells which are produced by gas lift, and often presents a serious problem when, this method of producing the oil is used. In older fields paraffin is also deposited on the face of the producing sand that on the walls of the hale or within the interstices of the sand near the hole, and this materially affects the amount of oil that can enter the well.]

Jan 1, 1927

By Roy H. Grau

The National Institute for Occupational Safety and Health (NIOSH) has conducted research to improve the ventilation of large-opening mines whose entries are at least 93m2 (1,000 ft2). The ventilation of large-opening mines is unique compared to other types of mines because (1) it is challenging to keep airflow velocities high enough to effectively remove or dilute airborne contaminants because the entries are so large, (2) large air volumes can be moved through the mines with little static pressure drop, and (3) stoppings that are used to direct ventilation airflows are costly to construct and to maintain. The research results suggest that the ventilation of large-opening mines is improved significantly by incorporating ventilation planning into the mine planning process, using propeller fans to direct airflow, developing new stopping materials and construction methods, and using long pillars to eliminate crosscuts where possible.

Jan 1, 2009

The production of harmful pollutants from coal mines and/or from coal and associated strata has been a recognizable fact in the United States for over two hundred and seventy years. In 1698, Gabriel Thomas observed(l) that the colored water flowing from streams in this country was similar to that which flowed from the coal mines in Wales. Hence, water pollutants such as acid were being produced before any known coal mines were operating in this country. The coal mining industry has contributed to the increase of pollution by exposing large amounts of sulfide materials that enable the reaction of water, oxygen and sulfur containing materials to form acid. A map of the United States coal fields can be seen on Figure 1. The anthracite regions of Pennsylvania, although small when compared to the total reserves, have produced some of the country's major water problems. The map indicates the extent of bituminous reserves of the Appalachian and midwest regions. Also evident are the bituminous, subbituminous and lignite coal reserves in the west which have recently come into greater demand. Acid mine pollution is encountered in numerous states, but the major problem is found in the Ohio, Susquehanna, and Potomac River basins.(2) Most coal beds contain some sulfur which may be in the inorganic, sulfate, or sulfide form, and thus have the potential to produce sulfuric acid. However, much of the strata that overlays the coal beds also contains acid neutralizing materials. Therefore, the amount of acid produced depends upon the amount of both acid and alkali materials that dissolve in the water in any given mine. The common sources of sulfurous material in the seam or surrounding rock are generally called sulfur balls or "nigger heads" by the miners. Sulfur balls that have been observed(3) seem to be equally divided between those containing sulphuritic iron capable of producing sulfuric acid upon oxidation and those that are primarily calcium carbonate. It has been observed in many instances that two types of water, acid and alkaline, are being produced in the same mine. A study of the geological strata and a survey of subsidence, faults and sulfur balls will usually give some indication of why this happens. The reaction of pyrite (FeS2) with oxygen and water to form ferrous sulfate (FeSO4) and sulfuric acid (H2SO4) by a series of complex chemical interactions is well documented but not well understood.(4,5) However, it is well known that the reactions to form the acid cannot occur unless all three constituents are present. Since pyrite is inherent in most coal seams and air is needed to sustain the miner, the most logical answer is to eliminate water infiltration into the mine, or to remove it from the mine before acids can form.

Jan 1, 1970

By Forrest T. Moyer

In conjunction -with the statistical survey of the lime industr-.r in 1939, by the Bureau of Hines, producing companies reported the lime-fuel ratios attained in their plants according to type of kiln and kind of fuel. Each ratio, expressed as the number of pounds of lime burned by a unit quantity of fuel, was weighted according to the tonnage of quicklime pro- . duced at the reporting plant and grouped with similar data from other plants, so that an average ratio for each type of fuel and,kiln could be calculated. By this method the variables trat affect ratios of individual plants are more or less equalized, and the computed average lime-fuel ratios provide a fair measure of kiln and fuel efficiencies during 1939.

May 1, 1941

By J. F. Barkley

The following questions and answers were prepared principally to supply information in answer to general inquiries received by the Bureau from those contemplating the use of propane and butane fuels . Primary or basic information only is covered; this usually gives enough guidance for most inquirers . To those who wish information of the treatise type , the handbook , Butane- Propane Gases , published by the Jenkins Publications , Inc. , 1709 West 8th Street , Los Angeles 14, Calif . , is suggested .

May 1, 1949

Develop technology for preparing thick corrosion-resistant coatings and electroforms of iron-chromium-nickel alloys. Approach To reduce the United States' dependence upon foreign sources for supplies of strategic and critical metals such as chromium, cobalt, and nickel, new technology must be devised to conserve these valuable commodities. One approach being investigated by the Bureau of Mines is the use of a modified-aqueous-electrodeposition method to prepare thick (-25 µm), complex alloy coatings (e.g., stainless steel composition) with properties similar to the commercial alloys. An alloy coating on a low-alloy steel or carbon steel substrate would require significantly less strategic and critical metals than those contained in an equivalent mass of the commercial alloy. Coatings applied to appropriate mandrel materials make possible the preparation of intricately-shaped alloy electroforms (near-net-shape parts). As a result, the loss of valuable metals associated with machining finished products would be minimized.

Jan 1, 1986

By C. L. Brown

Coal has been transported by belt conveyors in mines for many years; however, only since the beginning of the general mechanization period have complete transportation system of this type been employed. Aside from my complete belt-conveyor transportation systems, belt conveyors are frequently used in conjunction with other transportation. Many early installations, for the most part, were made without standards as a guide. As a result, some States have outlined certain requirements based more or less on experience following mine fires. Correlation of these regulations should result in more uniformity in connection with standardization of regulations. The National Electrical manufacturers Association has published standards for mining-belt-conveyor installations2/ that should be helpful to the coal-mining industry generally. Bureau of Mines Schedule 2F3/ requires certain controls for permissible-belt- conveyor drives, and similar requirements are listed in Bureau of Mines bulletin 514.4/ Committees of the American Mining Congress have prepared much valuable information concerning operation of belt conveyors, and a subcommittee on fire-resistant belting has been active. 5/

Jan 1, 1956

By A. B. Hooker, R. A. Kearns

Material used for flame safety lamp gauzes should possess the following qualities: (1) mechanical strength, (2) resistance to corrosion under service con- ditions, (3) a relatively high thermal conductivity, (4) a melting point above the ignition temperature of mine gas. Heretofore, three metals have been used for flame lamp gauzes, namely: steel, brass and copper. While each of these has the requisite qualities to some extent, none of them is an ideal gauze material. Copper gauzes lack mechanical strength, especiall, after they have been heated; brass and copper both have comparatively low melting points so that before the gas ignition is reached the gauze metal is attacked and oxidized under the action of the heat. Steel corrodes readily in damp atmos- pheres and if the lamp stands unused under these conditions for some time, the gauzes become unfit for service. Tests of these three materials have shown that steel offers the highest degree of safety. Manel metal, the natural alloy of nickel and copper, is practically noncor- rodible. Its relting point is approximately the same as that of steel. From time to time it has been suggested that this alloy might be a better gauze material than steel, since gauzes made of Monel metal should have all of the good qualities that steel gauzes possess and, in addition, would not corrode appreciably in ordinary mine atmospheres. One advocate of this use for Monel metal, the International Nickel Co., through their development engineer, Mr. Robert J. McKay, cooperated with the Interior Department, Bureau of ines, to the extent of supplying twelve sets of 30 mesh, Monel-metal gauzes for tests. Those gauzes were made up by the same lamp manufactur- er ho rade the steel gauzes used in the previous investigation. Being made by the same processes as the steel gauzes, these Manel-metal gauzes were needlessly given the same anti-rust coating that is always applied to steel gauzes to prevent any corrosion before the gauzes are used. In previous tests the Bureau of Mines had collected data as to the behavior of steel gauzes. In determining the value of Monel metal as a gauze material, it was planned to obtain similar data with Monel-metal gauzes, and thus make a direct comparison with the steel gauzes. In addition, steel and Monel-metal gauzes

Apr 1, 1923

By N. E. Hanna

To be authorized for use in coal mines, explosives and blasting devices must pass certain safety tests prescribed in schedule 1F,3/ on the basis of extensive practical and theoretical research by the Explosives Testing Station of the Federal Bureau of Mines. An explosive or blasting device that passes these tests is placed on the active permissible list. As this list is constantly revised, it has been the practice of the Bureau of Mines periodically to publish the names of explosives and blasting devices that have been added to the active list, as well as those that have been transferred to the inactive list; changes in brand names also are reported. This circular covers all permissibles including additions, transfers, and changes made between December 31, 1945,4/ and December 31, 1951.

Jan 1, 1952

By Joseph A. Sutton

The prospect of utilizing bacteria in mining and metallurgical processes introduces a new and challenging area of investigation. Elements of bacteriology and metallurgy are discussed in connection with possible areas where biological science might be applied in extractive metallurgy. Bacteria may prove important in the selective separation of metals from ores and metallurgical solutions, the production of sulfur from gypsum or pyrites, and the production of sulfuric acid from elemental sulfur. A series of reports concerning the experimental applications of bacteria on minerals and metallic ores will follow this paper. For several years the Bureau of Mines has been investigating the action of bacteria in the oxidation of sulfide minerals and their potential uses in metallurgical processes. Primary attention has been given to the possible utilization of certain strains of autotrophic bacteria that live in industrial leaching solutions or fractures of mineral outcrops. The purpose of this paper is to acquaint the mining and metallurgical engineer with micro-organisms and some of their possible applications in the field of extractive metallurgy.

Jan 1, 1961

By L. Cheng

This Bureau of Mines report summarizes an investigation of the amount of respirable dust adhering to the surfaces of seven run-of-face broken bituminous coals. The number of respirable-size (0.9 to 10 micrometers) particles adhering to the run-of-face coal ranged from 1011 to 1012 particles per pound of coal and was approximately inversely proportional to the mean lump size of the coal sample, otherwise it did not vary significantly with the coal seam, mining method, or winning machine. Based on these results, about 16 lb of ordinary run-of-face broken coal would have enough respirable-size adhering dust to contaminate 1,000,000 ft3 of air up to the 2 mg/m3 level, if this adhering dust should become airborne. Although brief studies here suggest that a negligible amount of new respirable dust is formed due to fracture of the broken coal during dropping, dislodging of old adhering particles during secondary handling operations is a potentially dangerous source of airborne respirable dust.

Jan 1, 1973