Search Documents

As part of its research on advanced mining technology, the U.S. Bureau of Mines emphasizes studies on in situ leach mining. This research enables the Bureau to develop technical information that can allow mining companies to adopt in situ leach mining methods. Research results should help to remove the technical and economic barriers currently hindering the development of commercial in situ leach mining operations. This report contains papers summarizing results of Bureau research on various aspects of in situ leach mining. A featured topic is the cooperative field experiment of the Bureau and Santa Cruz Joint Venture in a copper deposit near Casa Grande, AZ. Discussions in-clude an overview of the entire project, cost modeling, environmental permitting, laboratory core-leaching experiments, petrographic studies, and an evaluation of the geologic structure in the region. In addition, papers describe hydrologic modeling and geophysical studies of solution flow during leaching. Preliminary geochemical modeling studies are also summarized. A final paper describes a nonionic chemical additive with potential for significantly reducing the high costs of drilling in in situ leach mining.

Jan 1, 1989

Provide improved permanent stoppings designed specifically for use in mines with large cross-sectional entries. Approach The large entry sizes in many mines, such as oil shale, salt, and limestone, make the conventional stopping construction techniques used in smaller opening mines unacceptable. The Bureau of Mines and Colorado Mining Association jointly sponsored a contract to design and test new or modified stopping concepts for these mines. The most promising concepts were then tested in an oil-shale mine having 30-foot-high by 55-foot-wide mine entry openings. All stopping designs tested were evaluated in terms of cost, air tightness, and resistance to blast damage.

Jan 1, 1987

By Choon Kooi Quan

Water availability is essential for mining and minerals processing. To provide government and industry with recent data for water use planning and management, the Bureau of Mines canvassed a number of U.S. producers of nonfuel minerals to determine their water use in 1984. Data were analyzed and compared with previously published data in order to examine historical trends in water utilization in the nonfuel minerals industry and to estimate water requirements in the year 2000. Total water use in the domestic nonfuel minerals industry during 1984 was estimated at 2,267 billion gal, of which 571 billion gal was new water and 1,696 billion gal recirculated water. The largest users of water were the phosphate rock, iron ore, copper, sand and gravel, and crushed stone industries, together accounting for almost 90% of total used. More than one-half of all water was used in Florida, Michigan, and Minnesota. In the year 2000, total water use will amount to an estimated 2,679 billion gal, of which 810 billion gal will be new water and 1,869 billion gal recirculated water. Most of this water would be used in producing the foregoing suite of minerals,

Jan 1, 1988

As part of the overall development of a borehole mining system -develop backfilling techniques to reduce possible damage to the environment caused by either the cavities or the piles of sand tailings that result from in-borehole hydraulic mining. (Borehole mining is described in technology News No. 56.) Approach Water filled cavities at the bottom of boreholes are rapidly and economically backfilled by jetting a sand-tailings slurry underwater. How It Works The Bureau of Mines borehole mining system creates a cavity having a horizontal diameter of more than 50 feet. (See photograph). This cavity can be backfilled with much of the sand previously mined. The sand tailings or similar backfill material is dumped by a front end loader into a slurry mixing tank at the rate of about one ton every three minutes. Enough water is added to give a thick, but pumpable slurry. The slurry is pumped down the borehole through a string of 4-inch pipe to the cavity. After passing through a right elbow at the end of the pipe, the slurry is ejected through a nozzle. The resulting slurry jet emplaces the backfill at the outer wall of the cavity. To obtain an even distribution of fill in the cavity, the nozzle is slowly rotated. The nozzle and pipe assembly is supported from a turntable on the surface. See diagram.

Jan 1, 1981

By Thomas C. Denton

In 1965 Africa maintained its position as a region of the world essential to advanced non-Communist nations for supply of vital metals and minerals. The position stemmed from the fact that Africa produced in large quantity a number of key minerals of which either or both resources and production capacity elsewhere did not approach the needs of the free world. The Republic of South Africa alone contributed more than three quarters of the gold mined in the entire non-Communist world besides an estimated 60 percent of metals of the platinum group and the entire new supply of amosite asbestos, and Africa as a whole was nearly the non-Communist world's only source of gem and industrial diamond. Africa also accounted for 83 percent of non-Communist world cobalt production. Besides these massive contributions, Africa in 1965 provided 50 percent or more of the new supply from non-Communist countries of the following mineral commodities: Lithium minerals, corundum, manganese ore: and chromite, and over 20 percent of new supply from non-Communist countries of columbium-tantalum concentrates, antimony, beryl, vanadium, phosphate rock, and copper. Africa also accounted for 18 percent of the non-Communist world's output of uranium, 14 percent of its tin, 11 percent of its lead, 9 percent of its zinc, and 8.9 percent of its crude oil output. With respect to chromite, at yearend Africa's reserves of the mineral were far larger than those of all other non-Communist regions combined. This probably also held true for manganese ore. In the case of crude oil, the fact that Africa's share of non-Communist world output was 1.6 percentage points greater than in 1964 was significant, particularly inasmuch as the output rate was continuing to increase at yearend.

Jan 1, 1967

By Nicholas G. Theofilos

The only mining activity in Belize during 1976 involved the production of construction aggregates, which were used domestically. A comprehensive ordinance regulating mineral prospecting and mining was proposed during the year. Under the ordinance, which would supersede all grants and titles, ownership and control of all minerals except petroleum would be vested in the Government. Exxon Corp. entered into an agreement with three oil companies to achieve a majority interest in nine oil prospecting leases covering 1 million acres, mostly offshore Belize. The agreement was with Weatherford International Inc. which had 30% interest in the leases, Ajax Petroleum Co. with 40% interest, and Canadian Superior Oil Ltd, with 24% interest. A new entity, Esso Ventures Inc., was established to be responsible for conducting extensive geophysical operations and drilling an exploratory well offshore Belize.

Jan 1, 1980

By James R. Cosby

This report describes work performed for the Bureau of Mines to evaluate available portable instruments for their effectiveness in detecting and locating damaged metallic shields in Types SHD and SHC cables. A second phase of the program is also covered wherein several instruments of a type which show promise are purchased for modification and testing to verify their performance.

Jan 1, 1980

More gold is being produced now than ever before in recorded history. All over the world huge quantities of ore are being mined and processed, thanks to historically high prices for gold and the use of processing techniques demonstrated as cost efficient in the last 20 years. Over the past 10-15 years prices for many other metals have been depressed, and gold has accounted for a significant proportion of worldwide exploration and development expenditures(l)1. The revenues generated from gold mining are providing greater return on investment, more jobs, and more tax revenues to national governments than ever before. Emerging nations are using the gold industry as a springboard for development; developed nations are continuing to fuel their economies with gold industry revenues; and China and countries of the former Soviet Union are using the gold industry to generate foreign exchange, modernize their mining industries, and take the first tentative steps toward private sector participation in their economies.

Jan 1, 1994

By John C. Machisak

DATA ON INJURY experience at quarries and related plants of the United States are presented in this publication under the following general sections: A) General injury experience: Tables 1-4: Contain current data on number of injuries, injury-frequency rates, work location, accident agency, degree of injury, and related employment data. (B) Injury experience at different kinds of quarries: Tables 5-6: Current data on number of injuries, injury-frequency rates, work location, accident agency, degree of injury, and related employment data. (C) Injury experience by States: Tables 7-19: Current data on the number of injuries, injury-frequency rates, accident agency, degree of injury, and related employment data. (D) Selected injury data: Tables 20-30: Current data on various selected factors of operating conditions at different kinds of quarries, including employment size-groups, length of shifts, comparative severity of injuries, and injury data and related employment experience at dimension-stone and crushed and broken stone quarries, and underground quarries. (E) Mining methods and historical injury experience: Tables 31-32; Employment data and injury experience in the quarrying industries of the United States, by mining method and work location, 1953-58; and historical injury experience and employment data in the quarrying industry, 1911-58.

Jan 1, 1962

By A. B. Hooker, L. C. IlsLey

"Observation of the use of trailing cables in ""mines shows that the chief limiting factor in the life of the cables and their safe use is the smashing or crushing of the cables in service, together with the effects of consequent splicing.Trailing cables are crushed when run over by cars, mining machines; and locomotives or when hit by falls of roof. Crushing damages the insulation and may cause failure at once or in later use. Failure may be either by short circuit between the conductors or by grounding to the track. The failure of a live cable causes electric arcs capable of igniting explosive mixtures of methane and air. Every cable failure in a gassy or dusty mine is, therefore, a real or potential hazard.Some mine operators do not allow the splicing of trailing cables for use in gassy mines, bet require that a damaged cable be immediately replaced and if repaired that it be used only in nongassy mines. Other operators allow the making of temporary splices to permit completion of the shift but require that such splices be remade and vulcanized before the cable is used again.Still other operators allow the continued use of temporary splices, which in general means that a cable is used until the splices give trouble in reeling, or overheat, or pull apart. Then the spliced sections are either cut out or the whole cable is replaced.Splices often determine the useful life of a cable. A splice poorly made may pull apart ueder mechanical strain and cause arcing that burn* the surrounding cable or ignites as or coal-dust. If it has lower conductivity a splice is the first part of the cable to heat; it may become so hot under load that it will burn apart and damage other parts of the cable, or, if it be a soldered splice, the solder may melt and allow parting of the cable. A poorly made splice often has insufficient insulation which may alloy short-circuiting between conductors or permit external contacts capable of giving an electric shock to one handling the cable. The splice is sometimes bulky from too much insulation and takes up too much room on the reel, causing uneven reeling; also by catching on the spooling device the oversized splice may receive expressive pulls and wear. Splicing is therefore a very important factor in the use of trailing cables."

Mar 1, 1932

By Nikolaos Polysos, Holger Witthaus

INTRODUCTION The classification system for German coal mining is the result of approximately 100 years of experience in roadway development and longwall mining. It is also based on different research projects covered by national and European research programs. Over the past 30 years, more then 600,000 m of road-ways have been driven and employed for mining activities. To properly describe the German rock mass classification system, therefore, it is useful to take a look at the main geomechanical preferences and common support systems. The decision about the most effective development technique and support system is based on a synthesis of rock mass classification and geomechanical analysis. The properties of surrounding rock, the in situ stress, and the influence of mining activities in several seams at each German mine must be considered for the evaluation of the expected deformation of the roadway. The mine layout, the requirements of ventilation and fire prevention, as well as the need to maintain emergency escape routes for the miners, require that the gate roads remain usable after the passage of the longwall face in most cases. Moreover, the gate roads must be maintained despite the high stresses that are applied during longwall retreat mining. Therefore, gate road design must address a broad spectrum of potential deformation environments. In the past, when gate roads were supported solely with yielding steel arches, lithologic descriptions of the surrounding strata conditions were adequate for the dimensioning of support and the prediction of the roadway deformation. The current conditions of multiple-seam mining at depths of up to 1,700 m require combined support systems, including pattern bolting and backfilled steel arches. Rock bolt support is used for development, after which (typically 50–100 m outby the face) the steel arches are installed and backfilled with building material (concrete) in order to achieve an optimized development rate. The rock mass classification system described below was developed especially for the conditions of German hard-coal mining. It includes the stress distribution caused by multiseam workings (including crossing goaf edges of former longwalls), as well as in situ stresses due to greatdepth and the presence of tectonic faults. It is based on the evaluation of four parameters: • Geotechnical analysis of drill cores • Geotechnical observation of the development face • Geotechnical classification of tectonic structures (faults) • Standard classification derived from geotechnical assessment and evaluation of stress conditions (using numerical modeling for stress calculation) ROCK STRENGTH One of the most important input parameters for describing strata conditions is the strength of the rock. The German classification system is based on a description of lithotypes. This method has been used successfully since the 1950s and is based mainly on the uniaxial compressive strength (UCS) of the material. An evaluation of the rock strength observed in a survey of approximately 82,500 samples of rock core yielded the results shown in Figure 1. The three most common coal measure rock types are mudstone, siltstone, and sandstone. Each shows a specific mean UCS level and a different spread between the minimum and maximum values. Sandstones, in particular, have a wide spectrum of compressive strength, ranging from approximately 40 MPa to greater than 130 MPa, with an average of 85 MPa. The causes of this wide range include different sedimento-logical preconditions, facies, and digenetic processes. [ ]

Jan 5, 2007

By J. E. Tiffany, J. J. McKitterick

"IntroductionThe Bureau of Mines is investigating the fundamental factors in breaking down coal at the face, which govern the production of lump coal in typical mines working, different coal beds. Tiffany and Nelson in 1923-21 conducted tests on methods of blasting and use of different explosives, in a mine working the Pittsburgh bed in Pennsylvania. They determined come of these factors quantitatively, and compared their results with those obtained when the regular mine practice was followed.Results of Previous InvestigationThe tests by Tiffany and Nelson showed that the use of the cartridge of smaller diameter than that used in mine practice, resulted in an increase of 5 per cent in the amount of lump coal passing over a 1-1/4-inch bar screen, with a reduction of 32 per cent by weight in amount of explosive required. On the other hand, they found that on reducing the weight of charge 20 per cent, and using the cartridge of larger diameter, the round would not throw down the coal satisfactorily.Experiments with ""snubbing"" showed a similar improvement in quantity of lump coal, end the coal that was blasted rolled forward into the working place. however, in recent tests at another mine where the coal Lad different physical characteristics, snubbing did not always result in the coal rolling forward, on account of clinging to the ribs, and was not found to be an advantage. Therein the writers of this paper recommend that tests be made before deciding upon the adoption of snubbing in a particular mine."

Aug 1, 1925

By William G. Pariseau

A brief description of a two-dimensional elastic-plastic finite element program intended for mine stability analysis is presented that includes detailed instruction for input data preparation and how to obtain output.

Jan 1, 1978

By H. H. Schrenk, Carlton E. Brown

"The purpose of this paper are (1) to present a broad picture of the recognized methods of measuring the various forms of atmospheric pollution; (2) to evaluate the significance of such measurements; and (3) to suggest suitable methods for obtaining comparative information on the concentration of contaminants in city air.The atmosphere (the gaseous envelope surrounding the earth) consists of a mixture of gases. These gases and their usual proportions are:4/The volume of water vapor in the atmosphere ranges from almost zero (in very cold weather) to about 5 percent arid averages about 1.2 percent.Strictly speaking, any other substance in the atmosphere or an excess of any of the substances mentioned (with the possible exception of water) is a contaminant. Needless to say, there are many contaminants in the atmosphere.In accordance with their physical state, contaminants may be classified as gaseous or particulate, and the latter may be classified as solid or liquid matter. Particulate matter, especially when dispersed in some medium such as air or some other gas, sometimes is referred to as dispersoid, and the complete system of gas and dispersoid is referred to as aerosol.All substances on the earth are potential sources of atmospheric contaminants. Combustible materials (particularly fuel for heating and power), sea water, earth or soil, metals, and animals (including man) are some of the important sources of contaminants.Ordinarily gases are produced by chemical processes, whereas dispersoids are produced by both chemical and physical processes. There are two general dispersoid-producing processes: (1) Condensation, in which molecules join to form larger units or particles, and (2) disintegration, in which large units are reduced to the particulate range (which for the purpose of this article may be considered to be from 100 microns, or 1/254 inch, down to molecular size) by such processes as crushing, grinding, abrading, and atomizing.“Condensoid"" is a convenient term for dispersoids formed by condensation, and ""disintegrasoid"" for those formed by disintegration. Solid condensoids are sometimes called ""fume,"" solid disintegrasoids ""dust,"" liquid condensoids ""fog,"" and liquid disintegrasoids ""mist.""5/"

May 1, 1942

By Kevin Connor

During 1986, the Government continued with efforts to ease the country's almost total reliance on coffee exports for trade revenues by allocating 45% of the Government's budget to commerce and industrial projects. The collapse in coffee prices in 1985 continued to exacerbate the country's growing trade deficit, weakened currency, and dwindling reserves of foreign exchange in 1986. Amoco Burundi Petroleum Corp., a subsidiary of Amoco International Oil Co., continued with plans to drill at least two exploration wells in Lake Tanganyika in 1987. Both offshore and onshore drilling exploration was planned by Amoco Burundi. Any oil or gas finds were expected to have substantial impact on the Burundian economy, as a major portion of the country's trade deficit was directly attributable to petroleum and gas imports.

Jan 1, 1988

By J. E. Murphy

The u.s. Bureau of Mines investigated electrode designs for electrowinning lead metal from a LiCl-KCl-PbCI2 electrolyte at 4500 C. The major objective of this investigation was to decrease the energy requirement for lead electrowinning. Electrolysis was performed in a bench-scale cell using several graphite electrode assemblies. Such parameters as electrode spacing, current density, and chlorine gas removal from the anode were investigated in the bench-scale tests. An optimum electrode assembly, termed the sawtooth design, was scaled up and operated at 3,000 and 4,000 A. The sawtooth electrodes operating at 3,000 A produced lead for 0.66 kW·h/kg. The electrodes were constructed by cutting large triangular grooves in the electrode surfaces. The electrodes were placed together such that the triangular peaks of one electrode projected into the triangular valleys of the other electrode. Chlorine did not build up on the anode with the sawtooth electrodes.

Jan 1, 1991

By David L. Shuck

This report was prepared for the Bureau of Mines to describe the current methods of design, construction, and development of wells for in situ leaching of uranium. The discussion includes the alternatives for well design drilling equipment and fluids, grout formulation and emplacement, well integrity testing and repair, and well development and stimulation. Current practice in these areas was determined through interviews with eight operators of commercial scale in situ facilities and is also discussed. Based on this information plus the authors' experience, recommendations are made regarding well design, construction, and development tor in situ leaching.

Jan 1, 1982

By Ren G. Dong, Kristine M. Krajnak, Dan Welcome

Continual occupational exposure to vibrating hand tools can damage the neural, vascular and other soft tissues of the fingers. Rat tail models have been developed to investigate the biological responses of the tissues to vibration.1-2 However, the biodynamic response of the tail relative to that of the human fingers has not been characterized. The objective of this pilot study was to compare the transmissibilities of rat tails measured via a scanning laser vibrometer to those of human fingers gripping a handle. Methods In Part I of this experiment, four male Sprague Dawley rats (6 weeks old) were exposed to discrete 5g-rms sinusoids of 32, 63, 125, 160, 250, and 500 Hz. The rats were restrained in Broome-style restrainers with their tails constrained without compression to an exposure platform via elastic straps as shown in Figure 1. The platform was attached to a vertically vibrating shaker. The vibration was measured for the array of points shown in Figure 1 using a scanning laser vibrometer (Polytec) and the transmissibility calculated for each point on the tail relative to the reference points on the platform. In Part II, three male human subjects were exposed at the frequencies specified in Part I - with the addition of 1000 Hz - at a magnitude at the ANSI <0.5-hr limit up to 63 Hz, after which the acceleration was held constant at 5g-rms. The subjects gripped an instrumented handle at 20 N as shown in Figure 2. The transmissibility was calculated relative to the reference points on the handle. [ ]

Jan 6, 2006

By Eric G. Kok

Complying with respirable dust standards is presently a critical problem for many longwall faces equipped with double drum shearers. Results are presented of research performed to increase the quantity and optimize the distribution of the water supplied to the shearer drums to control the shearer operator dust exposure. The effect on the total respirable dust produced by the shearer was also examined. During the research effort, a simple and inexpensive manually controlled valve system was designed and implemented on a shearer to distribute the water supplied to the shearer drums. Research showed that increases in water quantities are beneficial but associated pressure increases may induce respirable dust boilover negating potential advantages. Other essential parameters such as location of shearer operator, outside spray orientation and air quantity were considered in the evaluation.

Jan 1, 1986

By Frederick H. Raab

A power-line proximity-warning (PLPW) system must have a high probability of detection (alarm activation at a specific distance), low probability of false alarm, and minimal set-up and maintenance. Tests of electric-field sensors have not demonstrated a dependable alarm distance. Alternative sensing methods such as microwave radar, optical radar, and sonar can meet the requirements by direct measurement of the range from the boom to the power line. Suitable microwave techniques include RF pulse, chirp FM/CW, and baseband pulse. Baseband-pulse radar has adequate range capability and does not require expensive microwave components. The radar cross section of a power-transmission cable is adequate for its detection optical-radar systems based upon LEDs and photodiodes are inexpensive, but can achieve only marginal performance in this application because of their limited modulation bandwidth. Since laser diodes and cryogenically cooled photosensors must be used to achieve the desired range resolution, the cost of an optical-radar system is greater than that of a microwave radar system. Sonar systems are feasible, but are not as precise and cost at least as much as baseband-pulse-radar systems. The performance of both optical-radar and sonar systems is degraded by dirt, necessitating the inclusion of a "windshield wiper.&apos; Baseband radar appears well suited to the PLPW application. The cost of a baseband-pulse radar PLPW system is expected to be comparable to that of an electric-field PLPW system. Development and testing of an experimental model are therefore recommended.

Jan 1, 1982