Search Documents

By John T. Aydelotte, Martin J. Gavin

" Oil shale contains little or no oil as such , but it contains an organic material from which oil may be produced by destructive distillation" . This statement , or others conveying the same meaning, appears in many popular and techni cal articles on oil shale . It is based on the belief that the ordinary solvents of petroleum have but little action on the organic substances contained in oil- yielding shales , although on distillation these same shales may yield upwards of 50 gallons of crude shale oil per ton . A 50 - gallon shale thus yields by distillation 18.73 per cent of its weight as oil ( assuming the specific gravity of the oil to be 0.900 ) , although only a relatively small part of this can be recovered by extraction with such solvents as chloroform , carbon tetrachloride , and the like . In the course of certain experiments designed to determine the solubilities of different shales after they had begun to yield oil by distillation , it was found desirable to determine the quantity dissolved from certain unheated shales by various solvents , at or near the boiling points of these solvents . The method used and results obtained are presented below. These experiments were made in connection with the oil - shale investigations being conducted by the U. S. Bureau of Mines , in cooperation with the States of Colorado and Utah .

Jan 1, 1922

By Harry Dobroski, Larry G. Stolarczyk

Theoretical and experimental research sponsored by the U.S. Bureau of Mines shows that medium frequency (MF) electromagnetic (EM) signals propagate great distances in an underground environment such as a tunnel or mine. This propagation is enhanced by different mechanisms associated with the geology, and with the existence of metallic conductors in the entryways. In stratified geologies, a transverse electromagnetic (TEM) mode of signal propagation is possible if a low conducting layer is bounded above and below by higher conducting layers. In general, the difference in conductivities must be at least several orders of magnitude. Such geological waveguide conditions often exist in underground mines. Propagation via the waveguide effect is known as the "seam mode" of propagation. Another mode of propagation, the "tunnel mode," exists in underground entries with electrical conductors such as power cables, metal pipes, and phone lines. A monofilar mode of propagation exists when signals are impressed upon conductors and return via the surrounding rock. A bifilar mode of propagation exists when all signals exist only on local conductors. In a given location there is a combination of monofilar and bifilar modes that make possible an interaction between the conductors and a transmitting device in a tunnel or entryway. Signals can be impressed on or received from local conductors via magnetic dipole antennas (loops) or line couplers.

Roof falls continue to be the greatest single safety hazard faced by underground coal miners. During 1996-99, 44 coal miners lost their lives in rock falls, and nearly 2,400 were injured. In addition, nearly 6,000 noninjury roof collapses were reported. Roof supports are installed to protect the miners, but support system failures contributed to most of these incidents. Reducing the terrible toll taken by ground falls continues to be a major goal of research by the National Institute for Occupational Safety and Health (NIOSH). The purpose of these proceedings is to provide the mining community with a comprehensive survey of coal mine roof supports. Drawing on many years of research undertaken by the NIOSH Pittsburgh and Spokane Research Laboratories, this volume describes what types of support are available, how they work, and when they should be used. The major subjects covered include roof bolts, standing roof supports, cable supports, and longwall shields. Some special topics are also addressed, including an analysis of roof fall accident statistics, techniques for better skin control, material handling considerations, and longwall mining through recovery rooms. This proceedings volume also contains information on several important new technologies, which are described here for the first time: •Guidelines for selecting roof bolt length, pattern, and capacity that were derived from statistical analysis of the roof fall experience at 37 underground mines; •A new design method for longwall tailgate supports; and •A technique for measuring loads developed within cable bolts. The papers in these proceedings were presented at open industry briefings conducted by NIOSH on New Technology for Coal Mine Roof Support. The briefings were held in Norton, VA, Charleston, WV, Evansville, IN, Tuscaloosa, AL, Price, UT, Glenwood Springs, CO, and Washington, PA. The papers were also presented at the Mine Safety and Health Administration (MSHA) Preventative Roof-Rib Outreach Program (PROP) Seminar, which was held at the National Mine Health and Safety Academy near Beckley, WV.

Jan 10, 2000

By Christopher Mark, Anthony T. Iannacchione

Falls of ground continue to be one of the most serious causes of injury to U.S. miners. Of the 256 fatal injuries that occurred in mining between 1996 and 1998, 59 (23%) were caused by falls of ground (Table 23.1). Falls of ground affect some sectors of the mining industry more severely than others. For instance, nearly 40% of the 98 coal mine fatalities between 1996 and 1998 were caused by falls of ground. Underground miners are at much greater risk than surface miners. Nearly half (45 out of 101) of underground mine fatalities were attributed to roof, rib, and face falls, while only 6% of the 155 surface fatalities were caused by falls of highwalls or slopes. The goal of this chapter is to provide guidance to safety professionals tasked with preventing ground fall injuries. This chapter combines an analysis of the Mine Safety and Health Administration's (MS HA) accident and injury data with a survey of industry "best practices" to safeguard miners from ground falls. Ultimately, this approach can help to form the basis of a sound, proactive ground control program for the mining industry. SOURCES OF DATA All the injury data examined in this study were derived from MSHA's fatal investigation reports and the MSHA accident database. Because falls of ground often result in serious injury, MSHA "Fatalgrams" and fatal investigation reports provide a useful snapshot of ground control issues in the mining industry. These reports are available to the public (on the M FHA Web site at www.msha.gov). Fatalgrams, are one-page summaries that are usually published within a month of an accident. They contain very basic information about the accident with a graphic and a short section on relevant best practices. Fatal investigation reports are the official accident investigation reports filed by MSHA personnel. These reports contain general information about the mine, a, description of the accident, physical factors involved in the accident, a conclusion, and enforcement actions, Enforcement actions typically identify citations and discuss violations to the Federal Mining Law. MSHA also maintains comprehensive statistical data on the mining industry's accident and injury record. The law requires that mines file a report on every reportable accident that occurs, containing information on the accident's location, severity, classification, activity, and nature of injury A short narrative is generally included as well. Accident reports can be searched by many of the above fields.

By W. W. Adams

"Fatal accidents at coal mines throughout the United States killed 234 employees during January 1924, according to reports from State mine inspectors to the Bureau of Mines of the Department of the Interior, Included in the number of fatalities are 68 deaths caused by two explosions during the month, one explosion occurring in a mine at Johnson City, Ill., and causing 32 deaths, and the other in a mine at Shanktown, Pa., and causing 36 deaths. The fatality rate for the month was 3.94 per million tons, based on a production of 59,435,000 tons of coals In January 1923 the fatality rate was 3.52, based on 206 deaths and an output of 58,458,000 tons.Bituminous mines in all States reported 202 fatal accidents, the production being 51,170,000 tons., and the fatality rate being 3.92, as compared with 3.28 for January last year, For the anthracite mines in Pennsylvania, the reports covered 32 fatalities, which, on the month's output of 7,955,000 tons, indicated a fatality rate of 4.02 per million tons, as against 4.89 for January 1923.As compared with January 1923, the reports for January of the present year indicated lower fatality rates per million tons for all of the main causes of accidents except explosions. For falls of roof and coal, the fatality rate per million tons declined from 1.85 in January 1923 to 1,68 in January 1924; for haulage accidents the rate declined from 0.62 to 0.42; for explosives, from 0.19 to 0.12; for electricity, from 0.12 to 0.07. The rate for explosions increased from 0.21 to 1,31 per million tons. -- Reports of Investigations, Department of the Interior, Bureau of Mines."

Feb 1, 1924

Crosson and Peters treat the errors that result in miner location due to errors in the overburden earth model used for computing location. A parallel effort by J. Powell of PMSRC is discussed here, where the location method used is that of the Westinghouse location program - "Miner". This location program was tested by Powell by using arrival times generated from the overburden earth model of Table l* rounded to the nearest millisecond. Location computations were then made using 3 geophones at a time. The average location is tabulated for all geophone triplets except when 3 geophones are in line. Geophone arrays were as shown in Tables 2 and 3. The manner in which the test was done is illustrated in Figure 1. I. SUMMARY OF RESULTS The arrival time differences, based on the Table 1 earth model, together with geophone locations based on the array geometries of Tables 2 and 3, were entered into the computer, together with a stated depth of 700 feet and an estimated overburden seismic velocity of 10,000 feet per second. These parameter values were processed by the location program - "Miner". Figure 2 illustrates the interpretation of the plots and data. The tabular data and plots of Table 4 and Figures 3, 4, and 5 illustrate the location error results obtained. These plots indicate that for sources within the array, the errors are considerably less than the measured errors obtained during field tests of the present location system. The possible reasons for this discrepancy are noted in Part Eight (Earth Models).

Jan 1, 1974

Increase the recycling of critical and strategic materials by simplifying the indentification and segregation of scrap. Background Because the United States is dl-most totally dependent on imports of such critical metals as chromium, cobalt and nickel, Bureau of Mines research has been directed towards conserving these metals by increasing the recycling of the complex scrap materials that contain them. Experienced scrap sorters, using the traditional techniques of object recognition, spark tests, chemical spot tests, color, apparent density, and magnetic properties, can adequately sort a wide variety of alloy groups. However, the complex nature of new materials entering the scrap market has made sorting both more difficult and more important. Some new alloys contain so many components that separation by discrete alloys becomes a prerequisite for effective recycling. The Bureau has completed Investigations on two methods for rapidly sorting complex scrap mixtures. One method uses a combination of two low-cost instruments. The other uses a single sorting instrument. Both approaches are reported.

Jan 1, 1986

By R. S. Conti

The US Bureau of Mines (USBM) has developed an inflatable feed-tube seal (IFTS) for high-expansion foam generators. The IFTS is a lightweight, portable, rectangular inflatable bag that can be used by firefighters to rapidly seal large openings, such as those in underground mines, and to simultaneously provide a feed-tube for a high- expansion foam generator. Thus allows fire-fighting foam to freely flow to the fire site and control or extinguish the fire. Studies indicated that a high-expansion foam plug will travel 183 m (600ft) down an entry with a 4.5% rise in elevation, before leakage of foam from around the inflatable partition.

To facilitate compliance with title 30 CFR 75.1001-1(b), which requires testing and calibrating of trolley line automatic circuit interrupting devices at intervals not to exceed six months. Approach Calibration of a circuit breaker ideally implies the passage of the expected fault current through the sensing circuit, and observing a successful circuit interruption at the preset level within a specified time. On trolley lines, the required current may be a few thousand amperes, with maximum duration well exceeding one-tenth of a second. Any method of obtaining this calibration current Involving the trolley wire can contribute to wire sagging and other permanent damage to the haul-age system due to the high energy dissipated during the test. Also, control to assure that exactly the required level and duration of current flow is obtained implies the use of equipment which is simply not available In the ordinary mine. Under a Bureau of Mines contract, a circuit to achieve the necessary calibration pulse was conceived and built. How It Works Two prototype units were fabricated and have been field tested by MSHA technical support engineers in under-ground mines. The equipment consists of an electronics Package 20 x 24 x 8 inches and weighing 93 pounds, including a side-mounted circuit breaker, with a set of 8 foot long detachable, AWG #4/0 leads with plier-type clamps. The total lead assembly weighs 21 pounds.

Jan 1, 1981

By T. N. McVay

The Bureau of Mines has developed a field test for detecting the presence of columbium in a variety of minerals containing the clement. The test consists of fusing the mineral or rock powder with potassium pyrosulfate in a porcelain crucible, digesting the melt with hot dilute hydrochloric acid to release the columbium oxide (Cb205), and subsequently reducing the columbium oxide to a lower oxide by adding tin, which gives a blue color to the contents of the crucible. The method will detect 1 percent of contained columbium oxide (Cb205) in a mineral sample provided no tungsten is present. If a mineral containing appreciable titanium is test,-!d in the same manner, the solution in the crucible becomes violet. In the presence of columbium, titanium at first causes a violet coloration of the solution, which after a few minutes is masked by the stronger blue of the reduced columbium oxide. Although tantalum oxide (Ta205) does not interfere with the columbium test, tungsten gives a blue color that is indistinguishable from the color obtained with columbium. A simple method is available to detect the presence of columbium in the absence of tungsten, but when the presence of tungsten is suspected, the sample must be subjected to somewhat more elaborate chemical tests to determine the presence or absence of columbium. Although these latter tests can be made in the field, several steps are involved that arc best performed in the laboratory with simple equipment.

Jan 1, 1962

To provide a means for rapidly evaluating proposed mine layouts in order to avoid potential hazards while minimizing loss of coal. The Approach: Development of a computer program that will compute many possible mine layouts by changing the mine plan until the arrangement giving minimal hazards with optimum extraction is found. How It Works: The Hazard Evasion Program for Mine Planning, developed by the Bureau's Denver (Colo.) Mining Research Center, tests hundreds of possible solutions to a mining layout, and by sorting out the 10 best (based on the criteria of maximum safety for workers with minimum abandoned coal), limits the number of choices that need to be considered and appraised for applicability to a given mine scheme. The program is applicable for room and pillar or longwall mining, for oil and gas well hazards, and for other hazards that can be described mathematically such as channel sands, potential bad roof areas, faulting, voids, or water pockets.

Jan 1, 1974

By G. H. Schnakenberg

In response to the underground mining industry's growing concern with the exposure of workers to the diesel particulate matter (DPM) component of diesel exhaust, a method was developed to estimate the average workplace concentration of DPM that could be expected from using the new lower DPMemitting engines now being approved by the US Mine Safety and Health Administration (MSHA) when these new engines are equipped with state-of-the-art exhaust-control, technology for filtering and combusting DPM. The resulting estimate uses the MSHA-reported particulate index for these engines, the prevailing rule-of-thumb ventilation rate of 150 cfm/hp and the available diesel-exhaust filter technology that has been shown to be at least 80% effective in reducing tailpipe DPM. In the estimate calculation, every engine used in an underground mine is assumed to be equipped with this control technology. Under the stated reasonable conditions, an average DPM level of 90 µg/m3 (mass) is predicted as technically feasible.

By Carlton E. Brown

In 1935 , Brown and Yant / described a microprojector ( microscopic arrangement for projecting images on a screen ) for use in counting and measuring the size of dust particles in Owens - jet dust - counter and simila dry samples of dust collected from the air . In 1938 Brown and others , described a modification of this microprojector that could be used also in counting dust in impinger samples . Microprojectors of this second type have been set up by many mining companies and others and have been made commercially available . Hamly and Pullen5/ described a modification of this microprojector for use in making rapid comparative estimates on konimeter samples and other determinations . This report contains information on still another modification named the "midget microprojector " because of its small size .

Sep 1, 1944

To provide a simple means for rapidly checking methane concentrations at working faces in coal mines while remaining under permanently supported roof. The Approach: A light telescopic probe, through which a gas sample can be pumped Into a methanometer, has been developed. See Figure 1 [ ] How It Works: The telescopic probe consists of sections of small stainless steel tubing encased in sections of lightweight fiberglass tubing. When fully extended the probe is almost 19 ft. long; fully closed it is approximately 5-1/2 feet long. It can be used In either of these positions as well as at intermediate extensions. An approved methanometer is clamped to the probe by a support bracket.

Jan 1, 1975

By J. W. Paul, A. C. Fieldner

"In cooperation with the New York and New Jersey State Bridge and Tunnel Commissions, the Bureau of Mines has just completed the construction of an experimental tunnel in the Bureau's experimental mine at Bruceton, Pa., near Pittsburgh, Pa. The purpose of this tunnel is to make a final study of the ventilation problems arising in the adequate ventilation of vehicular tunnels for automobiles and trucks, especially the 9000-foot tubes that are being designed. to handle the traffic between New York City and New Jersey under the Hudson River.Chief engineer, Clifford M. Holland, of the Tunnel Commissions has shown that there are three principal problems involved in planning the ventilation of this tunnel, namely - (1) The amount and composition of exhaust gases from motor vehicles; (2) The dilution necessary to render these exhaust gases harmless; (3) Determination of coefficients of airflow and horse-power required in ducts, bends and openings.Composition of automobile exhaust gases.The answer to the first problem was obtained by making road tests on 101 automobiles and trucks at the Pittsburgh experiment station. These machines were taken from service without any previous adjustment so that the composition and amount of the exhaust gas may be taken as representative of actual operating conditions prevailing in the tunnel. A report covering the results of these tests was submitted to the chief engineer of the Tunnel Commissions, on November 1, 1920, and 411 be published in the report of the commissions. Several papers a have also been published in the technical journals summarizing the important results as regards tunnel ventilation and also with reference to gasoline losses in present-day motor car operation due to the general use of unnecessarily rich mixtures"

Oct 1, 1921

By H. Kenneth Sacks

The Bureau of Mines has developed hardware for electromagnetic (EM) detection and location of miners trapped in underground coal mines. This report describes a technique for using the developed equipment for locating uncased boreholes underground. Results of several field and laboratory experiments are described.

Jan 1, 1978

Provide means for rapidly re-establishing ventilation control in metal mines after blasting, for emergency applications, and for routine temporary use. Approach Two quickly-installed, parachute-like stoppings have been developed and tested by the Bureau's Pittsburgh Mining and Safety Research Center. How the Parachute Stopping Works The parachute stopping can be fastened to an existing anchor point, opened, and effectively block the air flow, in less than two minutes. Because the parachute stopping tends to be self-scaling, its performance is generally better than that of conventional fabric stopping. However, the periphery of the parachute stopping must be longer than the periphery of the mine opening, Figure 1 shows the parachute stopping deployed in a mine entry. To reduce leakage during routine use, the cloth at the periphery of the parachute stopping can be adjusted and then anchored at several points as necessary. This extra adjustment can also be done after the initial installation during mine rescue or mine recovery.

Jan 1, 1977

By J. Brad Seymour, Mark K. Larson, Richard L. Rains, Douglas R. Tesarik

For several years, researchers from the Spokane Research Laboratory of the National Institute for Occupational Safety and Health (NIOSH) have been using geotechnical instruments in underground mines to study ground control problems and develop means of reducing accidents and fatalities caused by ground falls. This paper describes many of the different types of instruments, sensors, and data acquisition equipment that have been used for these studies; briefly explains the advantages and disadvantages of various sensor technologies; provides practical recommendations regarding the use of specific instruments and data acquisition systems; and outlines a general approach to the design and implementation of a successful instrumentation plan. A wide variety of instruments are commercially available for measuring deformation, strain, stress, and/or load. If used correctly, these instruments can provide important quantitative information regarding the mining-induced behavior of the host rock, the performance of ground support systems, and the safety and stability of underground workings. Data collected from these instruments can warn mine staff of impending ground control failures or hazardous working conditions, as well as provide valuable information for the design of ground support systems and the configuration and sequencing of mining excavations. We hope that the practical information presented in this paper will encourage a more widespread use of geotechnical instruments in underground mines and lead to reliable measurements that aid the engineering decisions affecting the safety of miners.

Jan 10, 2000

Improve the accuracy of commonly-used mine air velocity measurement techniques. Approach The Bureau of Mines, through a contract with Ketron, Inc., conducted a detailed study to establish appropriate, generalized correction factors for commonly-used air velocity measurement techniques. The techniques used were centerline readings, continuous traverse and split traverse vane anemometer readings, and smoke cloud readings (see Bureau of Mines Bulletion 589 for details on the proper use of these techniques). The various measurement techniques were used at different mine test sites to measure different air velocities. The data collected from the test sites were used in a statistical analysis which determined a generalized correction factor for each measurement technique. The correction factor multiplied by the measured velocity was used to provide the true velocity.

Jan 1, 1984

By R. H. Grau, S. B. Robertson, R. B. Krog, T. P. Mucho

Stone mines represent the highest percentage of operating underground nonmetal mines in the United States. With the introduction of stricter Diesel Particular Matter (DPM) regulations, large-opening underground room-and-pillar stone mine operators are faced with implementing one or more alternative methods to reduce concentration levels including: install and maintain an effective ventilation system; install lower DPM emission diesel engines; the adding of DPM filters. The National Institute for Occupational Safety and Health (NIOSH) is actively researching various aspects of fan and stopping designs in an effort to improve the ventilation of these mines. NIOSH has identified and further developed three alternative ventilation methods for use in large-opening underground mines: split-mine, perimeter, and unit-ventilation. This paper describes the implementation of the three methods with respect to their use in mines of various levels of development.