Search Documents

By R. Karl Zipf

The sudden, violent collapse of large areas of room-and-pillar mines poses a special hazard for miners and mine operators. This type of failure, termed a 'cascading pillar failure' (CPF), occurs when one pillar in a mine layout fails, transferring its load to neighbouring pillars, which causes them to fail, and so forth. Recent examples of this kind of failure in coal, metal and nonmetal mines in the U.S.A. are documented. Mining engineers can limit the danger presented by these failures through improved mine design practices. Whether failure occurs in a slow, non-violent manner or in a rapid, violent manner is governed by the local mine stiffness stability criterion. This stability criterion is used as the basis for three design approaches to control cascading pillar failure in room-and-pillar mines-the containment approach, the prevention approach and the full extraction mining approach. These design approaches are illustrated with practical examples for coal mining at shallow depth. Cascading pillar failure {CPF) in room-and-pillar mines can go by many other names, such as `progressive pillar failure', `massive pillar collapse', 'domino-type failure' or 'pillar run'. In this kind of failure when one pillar collapses the load that it carried transfers rapidly to its neighbours, causing them to fail, and so forth. This failure mechanism can lead to the rapid collapse of very large mine areas. In mild cases only a few tens of pillars might fail; in extreme cases, however, hundreds, even thousands, of pillars can fail. CPF can have catastrophic effects on a mine, and sometimes these effects pose a greater risk to health and safety than the underlying ground-control problem. Usually, the CPF induces a devastating air blast as a consequence of the displacement of air from the collapse area. An air blast can disrupt the ventilation system totally by destroying ventilation stoppings, seals and fan housings. Flying debris can seriously injure or kill mining personnel. The CPF might also fracture a large volume of rock in the pillars and immediate roof and floor. In coal mines and certain other mines this can lead to the sudden release of large quantities of methane gas into the mine atmosphere; a methane explosion might result from the CPF. CPF is at the far end of the spectrum of unstable pillar failure. At the other end are slow `squeezes' that develop over days to weeks and, because of their slow progress, do not pose an immediate danger to mining personnel. There is ample warning time for men and machinery to get out of the way of the failure. In a CPF, however, the failure progresses so rapidly that men and equipment cannot be evacuated in time. Significant seismic energy is released as a consequence of the rapid failure and collapse. CPF should not be confused, however, with coal-mine bumps and rockbursts. In some cases the damage can appear similar, but the underlying mechanics are completely different. As will he shown later, the mechanics of CPF depend on the applied vertical stress and the post-failure, i.e. strain-softening, behaviour of the pillars. In a CPF pillars shed their applied load rapidly and have very little residual strength after failure. The collapse itself may release significant seismic energy, but otherwise the mine is seismically quiet. Alter a CPF the openings in the affected mine workings have usually closed completely. In contrast, coal-mine bumps and rockbursts occur in seismically active mines. Research has shown that coal-mine bumps and rockbursts are seismic events induced by mining that damage underground mine workings. Bumps and bursts are thus a subset of a much larger set of mining-induced seismic events.[ Only some of these seismic events damage mine workings; fortunately, most do not. The mechanisms by which a mining-induced seismic event can lead to a damaging coal-mine bump or rockburst is still a significant research area.2 After a bump or rockhursr the affected mine workings may or may not be completely closed. For example, in the coal-mine bump described by Soler and co-workers2 the mine workings remained open even though the pillars were destroyed during the bump event. Because CPF differs from a coal-mine bump or rockburst, the design approaches to control their occurrence also differ. The design recommendations developed here apply to CPF and not to bump- or burst-prone mines. Cascading pillar failure examples Unfortunately, CPF has occurred in room-and-pillar coal, metal and non-metal mines. The most infamous example is the Coalbrooke colliery in South Africa, where 437 miners perished where [si >1 3at1ttsumsus7car kky vArtMixiL7i nesafr tramwsamn ures] on 21 January, 1960.1 Table I summarizes the mining dimensions of 13 examples of rapid pillar collapse in U.S. coal mines. All occurred during the 1980s and 1990s, and all happened suddenly or without significant warning. Most resulted in air blasts and damage to the ventilation system. Table 2 gives the mining dimensions of six room-and-pillar metal and non-metal mines in the U.S.A. where failure occurred in all probability by the CPF mechanism. The collapse areas can be huge. Fortunately, some of these failures gave advance warning. At the lead-zinc mine slabbing from pillars and roof falls began four weeks prior to the main collapse.3 At the copper mine considerable rock noise and smaller failures preceded the main collapse by five days.5 At the copper-silver mine it is not known if nature provided a warning.6 Evidently, the trona mine collapsed without warning.7,8 Rock noise and other failure warnings preceded the silica mine collapse by three weeks. v The presence or absence of warnings at the salt mint is not known. to Most of these collapses induced a substantial air blast; damage to the ventilation systems was limited, however, to bent airdoors and a few downed stoppings, except at the trona mine where extensive damage to the ventilation system resulted.

By Stephen L. Tillim

Tubular Handles can negatively affect the contents of the carpal tunnel. Years of injuries from grasping handles for tools and machines can cause carpal tunnel syndrome, tendonitis and wrist joint injuries. The can cause inability to use a hand and resulted in the longer absences from work than injuries from falls, accidents or fires.1 Cylindrical, tubular and rectangular handles are rolled flat structures. They place the hand on a rolled flat surface where the ends of the middle and ring fingers overlap the index and small fingers. They are pulled along a series of lines that contact the end joint of the index finger, the middle bones of the middle and ring fingers and the end bone of the small finger. Cylinders are pulled diagonally in the hand toward the carpal tunnel (CT) area. Gripping in this manner tenses asymmetric muscle groups in the forearm. Handles could work better if they do not place pressure on the CT and conform to the natural function or neutral hand position where the hand rests or dangles at the side of the body, the finger tips form a diagonal, the palm and fingers form a cup, the thumb rests between the index and middle fingers and the wrist is mildly extended. However, handles designed for the neutral position are pulled by diagonally oriented fingers into the valley between the thenar and hypothenar muscles where they can compress the median nerve and tendons exiting the CT. Seven principles for handles that do not place pressure on the carpal tunnel and employ optimal hand position are presented. First, handles should align the ends of the fingers parallel to the horizontal crease and not diagonally. Second, handles should extend from the cupped fingers to meet the muscles at the base of the thumb on the radial side of the hand and extend further on the other or ulnar side to meet a portion of the small muscles. Third, handles should have a recess on the proximal side to prevent contacting or placing pressure on the carpal tunnel. Fourth, handle design should be based on hand measurements in a position of function. Fifth, handles should come in sizes. Sixth, handles should be placed on tools to maintain the wrist and elbow in neutral position. The seventh is handles should support the maximum area of the hand and absorb, but not direct, vibration to the carpal tunnel. These principles led to prototypes and patents for handles for gripping, pinching and squeezing2,3,4 . The poster will illustrate and explain the principles Bonsil handles. Research, with existing tools, is needed to substantiate claims made for the Bonsil handle.

Jan 6, 2006

By Richard V. Ageton

"Everyone admits that there are more accidents in metal mines than there should be but there is much difference of opinion as to the causes of accidents, whether avoidable or unavoidable, and the amount of responsibility attaching to the miner and the mine operator, respectively. However, it seems that one of the main reasons why there are so many accidents, is that there is so little general knowledge regarding their causes and costs. Some information regarding the costs and causes of metal-mine accidents is presented in this paper.The data contained were obtained from a study of the complete accident and medical reports of two large metal-mining companies, which carry their own insurance. Path maintain hospitals with competent medical attendants. One of these companies also maintains a very efficient safety bureau, consisting of a safety engineer, with two assistants who work in connection with the medical department, and with the safety committee made up from among the miners themselves.Daring the year of 1920, ""A"" Company employed approximately 900 men, and these men worked more than 270,000 shifts. There were 373 minor and major injuries, among these 900 men, hence assuming that each injured man was hurt cut once, 41 per cent of the men who worked in this mine received some kind of time-losing injury during the year. On account of these injuries the injured men lost 3731 shifts, and thus the time lost due to injuries amounted to approximately 1.4 per cent of the total number of shifts worked,"

Oct 1, 1923

By Mark S. Sanders

The purpose of this work was to develop and field test improved knee protection for underground coal miners working in low seam mines. In a previous phase of this contract (Sanders, 1982), experimental knee pads were developed and field tested. The field test revealed several design deficiencies with the knee pads, and suggestions for improving the design were made. The work summarized in this report, therefore, consists of modifying the design and method of fabrication of the knee pads originally describes by Sanders (1982), and of field testing the improved design. The new prototype was shorter and wider than the original design, and used a neoprene pass-through strap design rather than a cloth strap molded into the pad itself. The new prototype was constructed by slush molding a hollow bladder that was then filled with foam. Initial reactions to the pads in the field test were very positive. However, after two months, the opinions about the new prototype became less positive. They were judged, generally, to be no better or worse than the pads usually worn by the field-test participants. Problems were encountered in the field with respect to durability. Water seeped into the inner cavity of many of the pads and caused the foam to deteriorate. It was concluded that it would not be cost-effective or feasible to significantly improve upon current commercially available knee pad designs.

Jan 1, 1986

By T. F. Morse, R. Lundstrom, A. J. Brammer, D. Peterson, M. Cherniack, T. Nilsson, J. D. Meyer, E. Toppila, G. Neely, N. Warren

HAVIC is a collaboration of investigators from North America, Sweden, and Finland having a scientific mandate from NIOSH, to study the exposure response relationship between vibratory tool exposure and adverse health effects. Five cohorts, the Suomossalmi forest workers cohort, Volvo truck cab workers, Connecticut shipyard workers, and matriculating dental hygiene students and experienced dental hygienists have been under study. In the case of shipyard workers, there was survey and tool exposure data from 1988, although detailed subject testing was only available within the timeframe of the study. The truck cab assembly workforce was an inception cohort that had been followed from 1994 along with age-matched controls. The Finnish forest workers had cumulative health data on a cohort (n=52) that had been studied from 1976. For a subset of these subjects, there was detailed tactometry testing in 1990, 1995, and 2003. Accordingly, there was historical as well as new prospective data for the industrial cohorts. The Suomossalmi cohort was reassembled only for our study, which precluded follow-up evaluation and because of retirement is almost certainly the last time this historic group will be studied. The study features are: • Characterization of the exposure response relationship for hand-arm vibration through a study design, incorporating multiple cohorts, some having existing historical data, • Selection of cohorts to include different types of vibration: oscillatory (forest workers) impact (truck cab workers), high frequency (dental hygienists) and mixed (shipyard workers), • Inclusion of two inception cohorts: dental hygiene students and Swedish truck cab workers, • Methods for multi-site and historical integration A description follows. [ ] Methods The study included surveys, physical evaluation, and a selection of battery of “best tests” (cold challenge plethysmography, multi-frequency tactometry, segmental sensory nerve conduction velocity [SNCV]1,2,3) applied across groups to quantify responses to exposure. Exposure monitoring included exposure characterization through daylong data logging at the individual level. Workers at each site were instrumented with a microcomputer-based Vibration Exposure Monitoring (VEM) system, developed at the Biodynamics Laboratory of UCHC and about the size of a police walkie-talkie, to record user-specific tool-operating times, vibrations, and grip forces throughout all, or a representative part, of their workday. More specifically, data logging methods involved the direct monitoring of work cycles, involving tool operation time and measures of tool vibration, namely the root-mean-square (RMS), root-mean-quad (RMQ), and root-mean-oct (RMO), and grip forces, each calculated per minute. For this study, the questionnaire was homogenized with other vibration studies4,5,6. Cross-translation was directed by the multi-lingual investigators, and then reviewed by the study team. To extend comparability with future international studies, questions were also added from the Vibration Network (VINET) draft questionnaire, the product of a European

Jan 6, 2006

By Lisa Steiner

Almost every process has a predecessor, and studying the predecessor helps to define needs and shortcomings to be addressed in the new design. It also suggests what information is needed by the users in order for them to be able to operate safely and effectively. The end users of a system can provide important feedback to better evaluate the current and proposed designs. When new technology is introduced into a system, mishaps may occur before it is realized that human-system interactions were not considered adequately in the design process. A systematic methodology to evaluate the causes of these injuries and to develop remedial recommendations can enhance safety. This paper illustrates how such an approach was used to assess remote machine operation in underground coal mines. The dynamic work environment of underground mining with its unpredictable geologic anomalies can result in numerous hazards. Many of these hazards, including mine roof collapse, occur near the working face where coal is being extracted. The face area is also where the most intricate interactions of people and equipment occur. For these reasons, a high priority has been placed upon minimizing hazards to the workers at the face. A remote control operation was introduced to provide a safer working distance from these hazards. As the remote control technology began to be widely used for extended cut mining operations, new issues became evident. It was essential to develop mechanisms for mines to evaluate these issues in order to predict and reduce injuries. Mining methods and equipment changes must allow for the ability of workers to adapt to changes in their dynamic mining environment. Consideration should be given to how the worker will use familiar information to make decisions in now unfamiliar situations. There will be both intended and unintended consequences [Merton, 1949]. Designers try to anticipate and eliminate surprises, but it is impossible to eliminate them all. How, then, will the new system affect the tasks to workers which are currently accustomed? As suggested below, this question may be addressed and more of the unintended outcomes predicted with a planned design process which includes strong human factors input to determine interactions and behaviors of participants.

Jan 1, 2005

By Travis Q. Lyday

Ecuador's economy continued to slow in 1982 due, in part, to declining foreign demand for oil, depressed world oil prices, and high international interest rates. Real growth of the gross domestic product (GDP) was estimated to be in the 2% to 3% range, down from the revised 4.3% recorded in 1981 and the 4.5% anticipated officially. In current prices, the GDP in 1982 was estimated at $12.1 billion.2 Inflation abated slightly from that of 1981 to an estimated 13.9% annual rate. The sucre was devalued in May by 32%, the first time in more than a decade, as a result of the pervasive flow of capital abroad. Ecuador's production of petroleum increased an estimated 1.9% in 1982 compared with that of 1981. The consortium of Corporación Estatal Petrolera Ecuatoriana (CEPE), the state oil company holding a 62.5% interest, and Texaco Inc. (37.5%) produced an estimated 98%, or approximately 211,000 barrels per day, of the total from the northern part of El Oriente, the eastern jungle region, where a Texaco-Gulf Oil Corp. partnership discovered oil in 1967. Gulf subsequently sold out to CEPE in 1977 for $117 million, Remaining production was from the Santa Elena Peninsula Fields on the Pacific coast where production has been steadily declining for several years.

Jan 1, 1984

By Robert B. Schluter

The Bureau of Mines investigated separating copper-nickel mattes to recover a copper-rich fraction suitable for processing by conventional copper metallurgical processes and a nickel-rich fraction suitable for processing in a hydrometallurgical nickel circuit. Distribution of cobalt and precious metals between the copper and nickel fractions was also determined. A matte containing a nominal 65 pct Cu, 9 pct Ni, 4 pct Fe, and 20 pct S was separated into a copper fraction that comprised 80 pct of the matte weight and contained 70 pct Cu and <1.5 pct Ni, plus a nickel fraction that contained 40 pct Ni and 30 pct Cu. Recoveries of copper and nickel into their respective fractions were 90 pct and 87 pct. These results were obtained in a laboratory flotation cell at a matte grind of 90 pct minus 500 mesh and a pH of 12.4, using 1.7 pounds DPG (diphenylguanidine) per ton of matte as collector and frother. Magnetic separation was used to remove metallic iron-nickel alloy from the copper fractions. Distribution of cobalt was about 70 pct to the nickel fraction and 30 pct to the copper fraction. Silver reported predominately to the copper fraction, while Au, Pt, and Pd were essentially entirely recovered in the nickel fraction.

Jan 1, 1982

Develop rugged, cost-effective fire protection for hydraulic shovels and backhoes. Approach Automatic fire sensing and suppression systems were designed and built for use on hydraulic shovels and backhoes. How It Works A line-type temperature sensor is mounted in the machine&apos;s engine and hydraulic pump areas to detect the heat from a fire while it is still small and easy to control. Two systems were tested. In one, the inside of the sensor consists of two conductors separated by a ceramic material whose electrical resistance decreases with increases in temperature. When heated to a predetermined temperature) the control circuit responds to the resistance drop. In the second system, the detection element of the sensor is comprised of a thin metal tube containing a hydrogen charged metal hydride wire. The tube is sealed at one end and is connected to a sensitive pressure switch at the other end. When exposed to the heat from a fire, hydrogen gas released from the metal hydride wire actuates the pressure switch.

Jan 1, 1980

Provide reasonably priced, reliable fire protection for blasthole drills. Approach An automatic fire sensing and suppression system using both dry and gaseous chemicals was developed, and is more shock and vibration resistant than similar industrial fire protection systems. How It Works Temperature sensors mounted in the drill&apos;s machinery house, hydraulic room, operator cab, and transformer area detect the heat from a fire, and trigger a sequence of actions. The same fire fighting sequence can be initiated from manual alarm boxes in the cab, hydraulic room, or machinery house. Electrical power to the drill Is immediately cut off, and a horn sounds to warn the drilling crew. After a 40-second, built-in, delay to allow time for drill&apos;s ventilating fan to stop, gaseous and dry chemical fire extinguishing agents are piped to and released in various rooms of the drill. The gaseous extinguishing agent (Halon 1301) is released in the machinery house, hydraulic room, and operator cab where dry chemical clean-up from electrical panels and machinery would be difficult and costly. Dry chemical is piped to the transformer room at the rear of the machine. Location of the principal components of the system are shown in the drawing.

Jan 1, 1979

By Linda L. Chasko, Charles P. Lazzara, Ronald S. (deceased) Conti, William J. Wiehagen

Fire has long been a concern for underground mine workers. A mine fire can occur at any time and can result in a partial or total evacuation of mine personnel and the loss of lives. Fires can grow rapidly. Time is the critical element. Prompt detection, timely and accurate warnings to those potentially affected, and a proficient response by underground miners can have a tremendous impact on the social and economic consequence of a small underground fire. Fire preparedness and response have components of technology and people. These components can work synergistically to reduce the time it takes to bring the system back in balance. This report deals with the preparedness of miners to respond to underground mine fires. It is intended to aid the mining industry in understanding the various roles of emergency responders and the training techniques used to increase their skill levels. The report also presents a technology overview to assist in effective response to mine fires.

Jan 12, 2005

By David K. Ingram

The development of large open surface fractures over mined-out coal longwall panels is the focus of this U.S. Bureau of Mines report. The research concentrates on defining the fractures characteristics and their controlling variables. The investigation was conducted at two mines in south-central West Virginia. All but one of the fractures are subparallel to the trend of the underlying longwall panel. One fracture is perpendicular to the trend of a longwall panel. Overall length of the fractures ranges from 60 to 900 ft. In cross section they are V-shaped, ranging from a couple of inches to 25 ft in width at the surface, but narrowing as they increase in depth. Fracture depth varies from a few inches to over 50 ft into bedrock. A vertical fracture or joint plane was observed in the bedrock at several open zones along the fractures. All of the fractures vary in elevation and do not parallel surface contours. The fractures are aligned with local joint trends, they correlate with longwall development, and they are situated in an increased tensional area over the mined out longwall panels. These observations indicate that the fractures are tensional openings along preexisting joint planes possibly triggered by longwall mining.

Jan 1, 1989

By M. G. Cherniack, A. J. Brammer, D. R. Peterson

Over the past two decades, there have been significant reductions in industrial exposures to hand-arm vibration, especially when specific tools and work processes have been redesigned to incorporate anti-vibration and ergonomic principles. Nevertheless, Hand-Arm Vibration Syndrome (HAVS) remains a significant occupational health problem as disease symptoms continue to occur even when vibration exposure levels believed to incur low risks have been reached2. This inconsistency may be related to the methodology that is typically used to estimate workday vibration exposure levels, involving laboratory and/or very short duration field measurements coupled with estimates of overall eight-hour tool operation times determined from brief observations of tool tasks and/or self-reported surveys. One solution is to use small, commercially-available, personal vibration dosimeters to calculate, record, and display long-duration vector sums and energy equivalents of vibration. However, since these devices are attached to the worker and require tool-mounted accelerometers, they are incompatible with the worker performing normal duties involving putting down or changing tools. In addition, these commercial systems do not allow for the characterization of the transmission of vibration to the hand such as monitoring the mechanical coupling between the hand and the tool handle (e.g., grip forces). O’Boyle and Griffin showed that variations in applied force can alter vibration transmission characteristics by 50% or more indicating that the measurement of grip force is essential for modeling vibration transmissibility and vibration exposures5. In summary, a need exists for the development of a method and device that will more accurately characterize workday-long vibration exposures. Methods A portable, light-weight, Vibration Exposure Monitor (VEM) system was developed to record user-specific tool-operating times, vibrations, and grip forces throughout all, or a representative part, of a workday. It monitors frequency weighted and unweighted accelerations from a palm-mounted uni-axial accelerometer (Model 352C22, PCB Piezotronics, Depew, NY) and calculates exposure levels using the root-mean-square (RMS) and higher power mean values, such as the root-mean-quad (RMQ) and the root-mean-oct (RMO). Grip forces are also monitored using a palm-mounted force sensor (Model 400, Interlink Electronics, Camarillo, CA) from which average grip force levels and exerted grip extrema are calculated. At the core of the VEM system is a commercially available, battery-powered microcomputer (Tattletale, Model 8v2, Onset Computer, Onset, MA) with one megabyte of memory and eight analog channels using 12-bit sampling at a single-channel maximum of 100 kHz. Analog signal processing (i.e., anti-aliasing, with cutoffs at 4 and 1250 Hz, and ISO 5349-13 frequency weighting) is accomplished using custom circuitry that is directly interfaced with the microcomputer. An embedded C-based protocol governs the data collection from each channel

Jan 6, 2006

The following methods should be used to protect miners from the adverse health effects of exposure to respirable coal mine dust and respirable crystalline silica: ? Informing workers about hazards ? Establishing written emergency procedures ? Using engineering controls, work practices, and personal protective equipment (including respiratory protection when dust control equipment is being installed, maintained, or repaired) ? Monitoring exposures ? Conducting medical screening and surveillance ? Encouraging smoking cessation ? Maintaining medical records

Jan 1, 1997

By James E. Mills

Coal, in the process of mining, transportation, and handling and on exposure to the weather, is subject to more or less disintegration. This disintegrated coal is usually called "slack" and amounts often to a considerable percentage of the lump coal produced in the mines. If this slack coal is wasted the loss so occasioned ranges from 5 to 50 per cent, or even more, of the total coal mined. It is therefore clear that the utilization of this waste slack coal becomes a serious economic consideration. When the coal is suitable for the production of coke, the utilization of the slack presents no difficulty, as it is in demand for that purpose. If the coal does not produce good coke, but cakes rather readily, the slack can be used for boiler purposes, as it fuses together more or less quickly, and burns on the furnace grate without great loss. Coal that cakes less readily can be burned on grates of special construc- tion. When so used it is more troublesome to handle, and the waste is greater than when lump coal is used. Consequently the price of much of the slack coal for fuel purposes ranges considerably lower than that of the lump coal from the same mine. The full value of this slack coal as fuel can be realized by first form- ing the coal into a coherent mass or briquet, such briquets, when of good quality, being equal to or of greater value than the original

Jan 1, 1911

By Victor J. Lynch

The Andover-Sulphur Hill mines are 12 miles northeast of Andover and 5 miles southeast of Newton, in Sussex County, N.J. The property is situated on the Lehigh Valley and Hudson River Railroad and half a mile east of U.S. Highway 206. It is connected with the main highway by a hard-surfaced county road. (See fig. 1.) Howard J. Hewitt of Lafayette, N.J., has under lease the Sulphur Hill tract, consisting of 28 acres, and has an option on the Tar Hill tract of 106 acres. The Tar Hill property adjoins the Sulphur Hill on the northeast. (See fig. 2.) The Andover-Sulphur Hill property is owned by the Lenape Corp. of Andover, N.J., while the Tar Hill tract is owned by the Crane Iron Co. of Phillipsburg, N.J. These mines produced iron ore during a period of about 100 years but have not been operated since 1880. Zinc and lead sulfides occur mixed with iron ores in the lower workings of the old mines. A diamond-drilling program was recommended to determine the extent of the sulfide mineralization in depth and also to explore further the iron-ore deposits on the property. The project was started October 6, 1942, and finished November 25, 1942.

Dec 1, 1947

By Michael A. Trevits

Mine fires can be especially perilous because toxic products can quickly spread well beyond the fire zone thereby exposing all underground miners to dangerous and deadly conditions. Since November 1998, there have been six major underground coal mine fires or explosions in the United States (Willow Creek (twice), Sanborn Creek, Loveridge No. 22, West Elk and the Jim Walter Resources No. 5 Mine). In each case, the entire mine or specific areas of the mine had to be sealed due to the build-up of dangerous gases and the fear of uncontrolled spread of the fire. Effective placement of mine seals can deprive a mine fire of oxygen and is often followed by water flooding or injection of inert gas into the affected area. When access to the fire zone is impossible because of safety reasons, airtight mine seals can be constructed, in the area of the fire, remotely from the surface through vertical boreholes. Remotely constructed mine seals are commonly made from cementitious material. Since these mine seals are typically erected blindly, it is difficult to determine if mine roof-to-floor and rib-to-rib closure has been obtained. This paper provides a review of the available materials and technology used to remotely construct mine seals through vertical boreholes.

Jan 1, 2002

By William Wiehagen

This trainer?s guide is designed as a reference manual. The purpose is to offer information and examples to skills trainers to assist them in structuring training for new operators of Walk-Thru roof bolting machines. Trainers can use this manual as a resource for helping trainees learn, understand, and apply knowledge and skills. In this sense, the guide is not prescriptive. It is designed to offer information and trigger ideas on what might be done to accelerate learning to those who are new to the roof-bolting task. On-site trainers can modify this guide to fit their conditions, machines and equipment, and work procedures. They can integrate roof control plans, company policies and procedures, and operators? manuals from the manufacturers of the original equipment into this guide. Every trainee is different and will come to the job with varying levels of relevant knowledge and skills. The trainer?s decisions on where to start, how to organize the on-the-job and classroom training portions, and when and how to offer different aspects of the training will be based on (1) a pretraining assessment of the trainee?s knowledge and skills and (2) the trainer?s experience in conducting skills training. The ?Skill Check? section might be useful for deciding where training should start among miners who have underground experience but limited knowledge of roof-bolting techniques. Every job carries a learning curve and likely has a number of ?teachable moments? where significantly new knowledge and skills can be learned.

Aug 1, 2006

By J. M. Stuve

Calorimetric determinations of the low-temperature heat capacities, standard enthalpy of formation, and high-temperature enthalpies were made of (Na20)4 ?Fe20,(c). The resulting values of entropy (S°), enthalpy of formation (?Hf°), and free energy of formation (?Gf°) at 298.15° K are 104.676 cal/deg mole, -656.2 ±.kcal/mole, and -603.4 A kcal/mole, respectively. Tabulations of Cp°, S°, - (G°-H°298)/T, H°-H°298, ?Hf°, ?Gf°, and log Kf are given to 1,200° K.

Jan 1, 1971

By J. H. East, D. Harrington

Fires in metal mines have resulted in some of the worst disasters in American mining history insofar as loss of life is concerned. One fire caused the death of 163 miners and individual less spectacular fires have cost the lives of scores of workers. Metal mines are often very deep, and the men working on numerous levels far removed from direct communication with the surface. In many instances they cannot be warned quickly of an emergency or a mine fire by telephone or other usual method of communication, or by messenger, flashing lights, gongs, sirens, or whistles. Telephones are not paricularly effective as a means of warning unless placed at all strategic points and with attendants always on duty; though telephones well placed have a definite value in any well-pla.mied emergency procedure in mines of all kinds. Messengers are slow and men working in remote parts of a mine would not receive a warning quickly enough. Most metal mines are not electrically lighted, except at or adjacent to shaft stations and in principal haulageways, and this limits the effectiveness of flashing lights. Electric gongs and sirens or whistles have been tried as warning signals, but the sound is quickly deadened and does not travel upward into the stopes, especially those of an extensive volume. Shutting off the compressed air is by no means satisfactory as a warning, as not infrequently it is stopped accidently, so that it loses its value as an alarm. The introduction of water into compressed air lines is undesirable as a fire warning and necessitates considerable care, especially in deep mines; pressure-reducing valves must be provided to reduce pressure that otherwise would break connections or split the pipe. A quick, effective method of warning miners underground of the existence of an emergency requiring them to leave the mine immediately, such as a fire on the surface or underground, is provided by the introduction of stenches in the compressed-air lines. This method of warning is by no means experimental, inasmuch as it has been used successfully for many years in

Jul 1, 1943