Search Documents

By Edward F. Divers

A new nonclogging water spray system for continuous-mining machines has been developed under contract with the Bureau of Mines. This paper presents installation and operating guidelines for the system, which consists of improved and easily maintained machine-mounted hardware, including an inline Y-strainer, a hydrocyclone, a backup filter, and two quick-opening valves for flushing particulates from the strainer and hydrocyclone. Underground tests with continuous-mining machines have shown that when properly installed and maintained, the new sys tern virtually eliminates nozzle clogging and thus greatly reduces spray maintenance. The sys tern is relatively inexpensive and has been installed on typical continuous-mining machines for a total cost under $1,000.

Jan 1, 1976

By L. C. IlsLey

In the normal operation of mines, the aggregate effect of many seemingly minor op rations may be very important as respects economy and safety. Anion: these operations is the method employed in coupling and uncoupling mine cars. For economic reasons the equipment in mines has not been protected as well as railroad equipment. It is pertinent that haulage accidents rank second in severity among mine accidents, and that manual coupling of cars has been one of the most frequent causes of such accidents. One study4/ revealed that coupling was responsible for about 20 percent of haulage accidents underground. A review of early conditions on steam railroads, which were responsible for the introduction of safer methods of coupling cars, indicates how conditions in might be improved. THE STORY OF RAILROAD COUPLING As any considerable improvement in mine-car coupling probably will follow lines somewhat similar to those that brought order out of chaos for the railroads, it seems appropriate to review briefly the steps taken to improve railroad coupling from the days of link and pin couplings of various types to the adoption of the standard ?M.C.E? automatic coupler.

Jan 1, 1943

By A. Wahab Khair, Richard D. Begley

"This paper presents results of destructive tests performed on rectangular coal specimen under the influence of two vertical and simultaneous wedge indentation forces. Several wedge designs and spacings were utilized in compression tests. The objective of these experiments was to qualitatively monitor the effect of different wedge designs and spacings on the stress distribution within the coal specimen.Coal samples from the Waynesburg coal seam were cut and trimmed to cubical dimensions of approximately 5 X 10 X 20 cm. These specimen were subjected to parallel compressive forces through two vertically applied wedge indentors. Loading was achieved with a hydraulic hand pump in order to facilitate interferogram construction. The load increments were limited due to the sensitivity of the holographic interferometric technique (holometry) in measuring small displacements; therefore, interferograms were taken only during similar increments in order to allow for a qualitative comparison between different wedge design and spacings. In some cases, interferograms were taken immediately before and after failure of the specimen.Introduction Failure Modes Three distinct modes of failure occur when geologic materials are subjected to wedge indentation forces. As shown in Figure 1, a crushed zone is located immediately adjacent to the indentor while chipping can occur if the fractures initiated in the crushed zone extend upwards to the free surface.. The third failure mode is a zone of intricate frac¬tures located between the crushed zone and the chipping zone. Several experiments have been conducted over the years to better understand crater formation and stress distribution within geologic materials under the influence of an indentor. Generally speaking, crack initiation and propogation observed in these experi¬ments correlate fairly well with wedge indentation theory; however, the nature of the .fractures is greatly influenced by different material properties such as grain size and cleavage planes. In other words, a wide range of behavior has been found in different rocks subjected to wedge penetration. For example, it has been observed that some rocks are merely crushed and indented while others are more prone to cracking and chip formation. Therefore, the development or nondevelopment of chips depends mostly on wedge geometry, rock type and depth of penetration. This work is part of the study associated with opti¬mization of cutting parameters, which is best modeled by using brittle materials and subjecting them to rigid wedge penetration tests."

Jun 1, 1988

By W. G. Bradley

THIS PAPER describing the quarrying, mining, and crushing of gypsum at the Blue Diamond mine, 11 miles from Arden, Nev., on the Union Pacific Railway, is one of a series on gypsum mining being prepared for and published by the Bureau of Mines. These papers are designed to disseminate technical information regarding the methods used. The cost tabulations represent operating expenditures only and not total costs. It is recognized that publication of total production costs might in some instances cause embarrassment to individual producers as well as to the industry as a whole. On the other hand, operating costs are essential to the technical discussion and study of the methods employed. The attention of the reader is specifically called to this differentiation in order that no misunderstanding of the scope of the cost tabulations shall ensue.

Jan 1, 1932

By H. D. Baylor

This paper, describing the operations of the Louisville Cement Co. in quarrying limestone for the manufacture of quicklime, is one of a series being prepared for and published by the United States Bureau of Mines on stone quarries throughout the United States. Those papers are designed to disseminate technical information regarding the methods used. The cost tabulations represent operating only and not total costs. It is recognized that publication of total costs might in many instances cause embarrassment to individual operators as well as to the industry as a whole. On the other hand, operating costs are essential to the technical discussion and study of the methods employed. The attention of the reader is specifically called to this differentiation in order that no misunderstanding of the scope of the cost tabulations shall ensue. ACKNOWLEDGMENTS The author acknowledges the assistance of J. H. Lemmon, plant superintendent, Charles Taylor, plant engineer, and F. H. Compton, chief engineer, of the Louisville Cement Co. in the compilation and preparation of this paper.

Jan 1, 1932

By John C. Machisak

THIS CHAPTER reports employment data and injury experience in the metal, nonmetal, quarrying, sand and gravel, and slag (iron blast furnace) industries of the United States in 1959. Each industry is treated separately, and no attempt has been made to combine data to show an overall total for this group of mineral industries. The slag canvass is included for the first time (data on employment and injuries were not collected before 1958), and, like other canvasses included in this chapter, data are voluntary. Employment and injury experience for all mineral industries can be found in volume III. The employment and injury information in this chapter came from reports submitted to the Bureau of Mines before May 31, 1960; therefore, figures are preliminary and subject to revision. Voluntary reports submitted by operators have contributed substantially to safety promotion since 1911, when the Federal Bureau of Mines started collecting employment and injury facts.

Jan 1, 1960

The performance of two large-capacity ventilation systems was compared through tests conducted in a large dead-end heading at a pilot oil shale mine in Colorado. Sulfur hexafluoride (SF6) tracer gas was used to measure the performance of the two systems: a free-standing jet fan and a reversible fan with rigid duct. The tracer gas was used to simulate the production of mine air pollut-ants, including blasting pollutants, hot diesel emissions, free methane from surrounding strata, and methane desorbing from muck piles. The test room was 55 ft wide, 30 ft high, and 320 ft long. The performance of the two fans was similar, but the jet fan used less power. The tests showed that either system could provide effective ventilation during oil shale mining.

Jan 1, 1986

By James V. Luxner

The airflow and methane distribution patterns developed in an equipment-free entry 6.5 feet high and 12 feet wide, ventilated by line brattice operated blowing to or exhausting from the face, were determined by the Bureau of Mines for varying conditions. Results of these studies show that blowing line brattice systems of face ventilation are more effective than comparable exhaust systems. The face ventilating efficiency of any line brattice system is dependent upon the method of ventilation, the face distance, the tight rib distance, the volume of air delivered to the end of the line brattice, and the volume of methane released at the face. Experimental results indicate that maximum face ventilation efficiency is achieved when the inby terminus of the line brattice is installed 5 feet from the face and at a distance less than one-third the entry width from the nearest rib. Analyses of data are based upon the ability of a face ventilation system to dilute methane in the immediate face area.

Jan 1, 1969

By J. T. McCartney

"INTRODUCTION The surface areas of the finest fractions of a pulverized material are disproportionately larger than their weights. For instance, Pesrott and Kinney 3/ showed that, in a sample of minus 200-mesh coal, particles that are about 2 microns in diameter represent 15 percent of the entire surface area but only 1.5 percent of the total weight. Because the sur- face area is the dominating factor in the behavior of finely divided materials in many practical processes, the role of the finest particles is of great importance. The oxidation and combustion of pulverized coal, both in the dry form and in suspension in oils, and the hydrogenation to fluid hydrocarbons of mixtures of pulverized coal and heavy oil are reactions in which the surface area of the coal particles has considerable influence. This investigation of the size distribution of fine coal particles was conducted with the hope that such processes would thereby be better understood. The results should also be of value in the study of the crushing and fracture of coal."

Sep 1, 1945

By Clete R. Stephan, Mark J. Schultz, William A. Slivensky, Eric S. Weiss, Kenneth W. Jackson

he Pittsburgh Research Center (PRC)~ and the Mine Safety and Health Administration (MSHA) are participating in a research program to evaluate the strength characteristics and air leakage resistance of seals and water trap designs for use in underground coal mines. This program is being conducted at PRC's Lake Lynn Laboratory near Fairchance, Fayette County, PA. Seals designed with a 40-cm-thick polymer (polyurethane) and aggregate core between two dry-stacked (no mortar) concrete block walls (coated on out by sides) withstood a 138-kPa pressure pulse while maintaining acceptable air leakage rates. Similar seal designs utilizing a 97-cm-thick, 91-kg/m7-density, polymer-only core did not survive; however, a 5 1 -cm-thick, 203-kg/mi-density, polymer-only core seal successfully withstood the explosion pressures. Evaluations of cellular concrete seal designs have shown that a two-pour slurry injection technique did not adversely affect the strength of the 1.2-m-thick seals when subjected to a 138-kPa pressure pulse. Two seal designs utilizing low-density cementitious block have also been evaluated with successful results. In addition to seal strength tests, various 15- and 30-cm-diam U-shaped water trap pipes and a water trough design were evaluated under explosion conditions and were shown to be inadequate when evaluated under worst-case conditions. Simple modifications to the various water trap designs were successfu1 in preventing the passage of explosion flame through the trap.

Jan 4, 1996

By Merle L. Bowser

The Bureau of Mines has constructed a miniature oxygen deficiency alarm system using an electrochemical cell as the sensor. Distinct audible signals are produced at either of two preselectable oxygen levels which can be varied from approximately 10 to 20.9 percent oxygen. The high or cautionary range produces a 500-cycle-per-second tone pulsed at about a 1-cycle-per-second rate, whereas the lower or more dangerous oxygen level produces a continuous 500-cycle-per-second tone.

Jan 1, 1968

By W. J. Fene

Ventilation is undoubtedly the greatest single safety factor in the operation of a coal mine. Any condition or occurrence that interrupts the ventilating current or changes its normal course through the mine workings is a distinct hazard and should be considered as such by every coal-mine owner, operator, and worker. The hazard, of course, is much greater in a mine that is emitting gas, as an explosive mixture can accumulate in a very short period if the ventilating current is interrupted. It is common to find one or more entries producing 600 cubic feet or more of methane per hour. If the ventilating current were short-circuited from these entries for 15 minutes, there would be an accumulation of 150 cubic feet of methane, which, when mixed with enough air to dilute it to the lowest explosive point, would make about 3,000 cubic feet of explosive mixture; this gas could be ignited in almost any normally operated mine by a cutting machine or other electrical equipment. The ignition of this quantity of an explosive gas-air mixture can readily cause an explosion of coal dust that would completely wreck the underground workings and possibly some of the surface structures. In fact, the ignition of one-tenth of the above quantity of an explosive mixture of gas and air might readily start an explosion that would, extend through every part of a large mine. The possibility of occurrence of interruptions to the ventilating current has received comparatively little consideration from mine owners, operators, and workers in many parts of the United States. Such a possibility should be considered in connection with every mine that gives off explosive gas, and steps should be taken to prevent it.

Jan 1, 1943

By Gordon E. Fletcher

This Bureau of Mines report outlines the atomic absorption analysis of oilfield brines for barium, calcium, copper, iron, lead lithium, magnesium, manganese, potassium, sodium, strontium, and zinc, using the method of additions. The advantages of using atomic absorption are discussed. The method of additions was chosen to overcome large matrix interferences usually found in brines; techniques of overcoming chemical, ionization, and background interferences are also described. The method was used to analyze several hundred oilfield brines and found to be rapid and reasonably accurate. A solvent extraction method was used to concentrate lead, copper, zinc, and iron in low-level samples.

Jan 1, 1974

By R. Hogg, T. F. Dumm

"Procedures for particle size analysis on respirable dust from coal mines have been evaluated. Using respirable dusts dispersed in a laboratory dust chamber, size distributions measured using cascade impactors have been compared with the results of a variety of laboratory sizing methods performed on samples collected on filters placed side-by-side with the impactors. The laboratory techniques included centrifugal sedimentation, laser diffraction/scattering and automatic particle counting. The general agreement among the various methods was very good, with systematic differences which can be attributed to the different definitions of size used. Simple conversion factors have been obtained which can be used to transform the laboratory data to equivalent aerodynamic sizes.Similar comparisons have been made on samples collected in underground coal mines. Again, the results are in quite good agreement although small discrepancies were observed in· some cases. These have been attributed to some degree of agglomeration in the airborne dust, leading to slightly coarser apparent distributions in the impactor samples INTRODUCTIONA primary goal of mine ventilation is the control of airborne dust, especially in the ""respirable"" size range, typically defined as finer than about 5 to 10 µm. It follows that determination of the amount and characteristics of the respirable dust is an important factor in evaluating the performance of ventilation systems. Particle size information on airborne dust in mines is commonly obtained by in- situ measurements using cascade impactors. However, these tend to be inconvenient for routine data collection and the alternative approach of collecting samples in the mine, on filters for example, and returning them to the laboratory for detailed analysis is very attractive. Questions have often been raised, on the other hand, as to the appropriateness of this approach. How well · do such laboratory methods describe the distribution of aerodynamic diameter of the airborne dust particles in the mine environment? The purpose of the work described in this paper was to evaluate some laboratory sizing methods and to compare the results of such measurements with the size data obtained by the direct, in-situ method."

Jan 1, 1989

By L. E. Dalverny

This Bureau of Mines report describes the deployment, 5-month operation, and lessons gained from a continuous gas monitoring system using sampling-tube bundles at an underground mine fire in West Virginia. Research information gained indicates the utility of relating certain gas concentration ratios to events during fire development, mine reventilation, and mine recovery. In addition to monitoring the quality of remote fly ash seals, the system provided timely warning of dangerous gas concentrations which developed during surface and underground recovery activities. An evaluation of system components is supplemented by recommendations for improvements.

Jan 1, 1975

By Richard Mainiero, James H. Rowland

For many years there have been small scale tests available for evaluating the toxic fumes production by cap-sensitive explosives (DOT Class 1.1), but these could not be used with blasting agents due to the large charge sizes and heavy confinement required for proper detonation. Considering the extensive use of blasting agent in construction and mining, there is a need to determine the quantities of toxic fumes generated by blasting agents. At the International Society of Explosive Engineers Twenty Third Annual Conference on Explosives and Blasting Technique in 1997, the authors reported on a facility for detonating large (4.54 kg), confined blasting agent charges in a controlled volume that had been constructed at the National Institute for Occupational Safety and Health’s Pittsburgh Research Lab’s Experimental Mine. Since 1997, this facility has been used to collect data on toxic fumes produced by the detonation of various ammonium nitrate/fuel oil (ANFO) mixtures and several cap-sensitive explosives. ANFO composition ranging from 1 to 10 percent (pct) fuel oil have been studied. As expected from previous studies, with an increase in fuel oil content the carbon monoxide production increases, while nitric oxide and nitrogen dioxide production decrease. The detonation velocity varies from 3,000 to 4,000 m/sec for the 1to 10 pct range of fuel oil content, suggesting that ANFO mixes with improper fuel oil content may appear to detonate properly, while their fume production differs significantly from optimum. The study also considers such factors as degree of confinement, water contamination, and aluminum content on blasting agent fume production. Results indicate that water contamination of the ANFO has little effect on carbon monoxide production, but causes significant increase in nitric oxide and nitrogen dioxide production. Decreasing confinement from Schedule 80 steel pipe to 0.4-mm thick sheet metal also has little effect on carbon monoxide production, but significantly increases nitric oxide and nitrogen dioxide production. Adding5 and 10 pct aluminum to the ANFO had no clear effect on carbon monoxide, nitric oxide, or nitrogen dioxide production.

By Jr. Schnakenberg

The National Institute for Occupational Safety and Health (NIOSH) has been working with diesel emissions control technology and the underground mining industry for a number of years. Underground isolated zone studies provided the emissions reduction performance of all of the alternative technologies currently available. A NIOSH/MSHA guide is available which provides mines with information and a process for selecting diesel particulate filters (DPF). Recent NIOSH experience suggests that more attention may be needed in managing the issues associated with diesel emissions and their control. The author argues that a holistic approach is needed which involves several key mine operations departments or disciplines by positing that workplace air can be considered as the product of a complex manufacturing process and examining how that process could be managed.

By T. J. Ballard

Corundum is a natural alumina (A120 ) and is next to the diamond in hardness . Except for the gem varieties , it is used principally as an abrasive , chiefly in grinding , dressing , and polishing metals and optical glass . Natural corundum is preferred to artificial abrasives for certain specialized jobs . Most of the corundum ( excluding emery ) mined in the United States came from the Corundum Hill mine in North Carolina and the Laurel Creek mine in Georgia . The Corundum Hill mine provided over half of the domestic production of corundum prior to 1900. Since 1900 , the importation of foreign corundum and the manufacture of artificial abrasives caused the decline of corundum mining in the United States .

Mar 1, 1947

By Claire C. Caruso, John M. Russo, Jennifer M. Schmit, Robert B. Dick, Edward M. Hitchcock

PURPOSE This report provides an integrative review of 52 recently published research reports that examine the associations between long working hours and illnesses, injuries, health behaviors, and performance. The report is restricted to a description of the findings and methods and is not intended as an exhaustive discussion of all important issues related to long working hours. Findings and methods are summarized as reported by the original authors, and the study methods are not critically evaluated for quality. SUMMARY In 16 of 22 studies addressing general health effects, overtime was associated with poorer perceived general health, increased injury rates, more illnesses, or increased mortality. One meta-analysis of long work hours suggested a possible weak relationship with preterm birth. Overtime was associated with unhealthy weight gain in two studies, increased alcohol use in two of three studies, increased smoking in one of two studies, and poorer neuropsychological test performance in one study. Some reports did not support this trend, finding no relationship between long work hours and leisure-time physical activity (two of three studies) and no relationship with drug abuse (one study). A pattern of deteriorating performance on psycho physiological tests as well as injuries while working long hours was observed across study findings, particularly with very long shifts and when 12-hour shifts combined with more than 40 hours of work a week. Four studies that focused on effects during extended shifts reported that the9thto 12th hours of work were associated with feelings of decreased alertness and increased fatigue, lower cognitive function, declines in vigilance on task measures, and increased injuries. Two studies examining physicians who worked very long shifts reported deterioration on various measures of cognitive performance. When 12-hour shifts combined with other work-related demands, a pattern of more adverse findings was detected across studies. Six studies examining 12-hour shifts combined with more than 40 hours of work per week reported increases in health complaints, deterioration in performance, or slower pace of work. Two studies com-paring 8- and 12-hour schedules during day and night shifts reported that 12-hour night shifts were associated with more physical fatigue, smoking, or alcohol use. Two studies examining start times for 12-hour shifts reported that decrements in alertness or more health complaints were associated with early 6:00 a.m. start times. One study examining 12-hour shifts in hot work environments reported a slower pace of work as compared with shorter shifts. Another study examining high workloads during 12-hour shifts showed increased discomfort and deterioration in performance as compared with shorter shifts. More definitive statements about differences between 8-hour and 12-hour shifts are difficult because of the inconsistencies in the types of work schedules examined across studies. Work schedules differed by the time of day (i.e., day, evening, night), fixed versus rotating schedules, speed of rotation, direction of rotation, number of hours worked per week, number of consecutive days worked, number of rest days, and number of weekends off. All of these factors could have interacted with overtime and influenced study results. Also, some studies did not report how many hours participants worked per week or other details about the work shifts, which complicated the assessment of their results. The many

Jan 4, 2004

By A. B. Hooker

All state mining laws require that flame safety lamps be used in gassy mines; the laws of some States require that safety lamps be kept for emergencies at every coal mine, whether gassy or nongassy. The use of the flame safety lamp has been widespread because it is the only defice readily available for detecting both the presence of methane and deficiency of oxygen. This paper reports the results of an investigation by the Electrical Section, in cooperation with the Gas Section, of the Pittsburgh Experiment station relative to the behavior of permissible flame Safety lamps in mine atmospheres deficient in oxygen and the effects of methan5/ on the detection of oxygen deficiency.

Jan 1, 1937