Search Documents

By G. W. Reimers

Exothermic oxidation reactions of sulfide minerals can produce self-heating situations in underground mines. If the self-heating is unchecked and the resulting heat is not sufficiently dissipated, the result can be spontaneous combustion fires. This U.S. Bureau of Mines report describes laboratory tests conducted to measure the reactivity of pyrite following treatment with additives to counter its self-heating tendencies. Thermal gravimetric analysis (TGA) and isothermal oxidation procedures were used to obtain information on pyrite ignition and the behavior of pyrite during low-temperature oxidation to ferrous sulfate. The determination of treatment effectiveness was evaluated by adding 5 wt pct of the compound to the pyrite before milling. The resulting samples were then heated in moistened air and after 24 h, the amount of pyrite oxidation determined. Results of these tests indicated that several phosphate compounds reduced the oxidation of pyrite to sulfate to about 50 pct or less compared with the oxidation of untreated sample at 200° C. Cupric sulfate reduced oxidation to about 20 pet untreated sample at 200° C. Sodium, calcium, and potassium chloride reduced pyrite oxidation to levels of approximately 15 pct or less of the untreated sample. Using only 1 pct of sodium or calcium chloride was effective in slowing pyrite oxidation to less than 20 pct of the untreated sample.

Jan 1, 2010

By M. M. Barr

Rapid expansion of the titanium-metal industry focused attention upon ilmenite as a possible substitute for the more expensive and less abundant rutile in producing titanium tetrachloride. Most of the rutile available for this use is imported. Preliminary studies were undertaken to determine the chlorination characteristics of high-titanium slags produced by electric-arc furnace smelting of alluvial Idaho ilmenite at the Federal Bureau of Mines Northwest Electrodevelopment Experiment Station, Albany, Oreg. Low silicon, calcium, and aluminum contents of the slags enhanced their potential value for chlorination.

Jan 1, 1958

By H. J. Lechtenberg

This Bureau of Mines report investigates solvent injection as a means of increasing oil production from low-gravity oilfields; thus, wells in two California oilfields that produce from reservoirs having low-gravity oil were injected with highly aromatic solvents to increase their oil recovery. The wells were either allowed to soak or the solvent was circulated for a period of time. In some of the wells, the solvent was followed by a slug of water. The post-stimulation production rate was considerably higher than the prestimulation rate of the wells. Wells in which the solvent was not followed by water showed an immediate increase in oil production, and essentially all of the solvent was recovered. The wells in which solvent was followed by water essentially showed a delay in the increase in oil production, thus indicating a temporary water block. The results show that the production rate is usually increased by the injection of solvent, and the method may prevent early abandonment of marginal producers. Cumulative post-stimulation oil production indicates that cyclic solvent injection treatment can be an economic success.

Jan 1, 1974

By H. C. Ko

Calorimetric determinations of low-temperature heat capacities and the standard enthalpy of formation were made by the Bureau of Mines for aluminum sulfide, A12S3. The standard entropy (S°), enthalpy of formation (?Hf°), and calculated Gibbs energy of formation (?Gf°) at 298.15 K are 27.93±0.05 call deg-mole, -155.6±0.9 kcal/mole, and -153.0±1.0 kcal/mole, respectively.

Jan 1, 1976

By Wing G. Agnew, Paul L. Russell

"INTRODUCTION During the past few years, the development of millisecond-delay electric blasting caps has made possible a more flexible control over timing the firing of individual charges in blasting, The use of these caps has proved especially productive in quarry blasting and in numerous construction operations, but their use in underground mining is developing more slowly, although in some cases, as the solution to a difficult breaking problem, they have been well-received. When used in metal-mine drifts, the general objection is that the broken rock is thrown too far. In nearly all cases, however, use of millisecond-delay caps results in better fragmentation of the rock and a lower powder consumption per ton of rock broken.Prom 1949 to 1952, several series of experiments were conducted at the Mount Weather, Va., Experimental mine in conjunction with driving a 6- by 10-toot ventilation raise. 3/4/ The raise-round experiments in this 238-foot shaft, using millisecond-delay electric blasting caps in various drill-round patterns, are the subject of this report.SUMMARY AND CONCLUSIONSAll rounds discussed in this report were drilled in the hard rock (epidosite and greenstone) of the ventilation raise at Mount Weather Experimental mine (figs. 1 and 2). The drill-round patterns varied from 28- to 32 holes and from a V-cut design to one having no cut boles at all. With the exception of the first two rounds, all blasting was done with millisecond-delay electric blasting caps. In all rounds 60-percent ammonia gelatin dynamite was used and holes were stemmed with two cartridges of sand stemming."

Apr 1, 1953

By Raymond M. Kacmar

This paper describes the Bureau of Mines research program on the reliability of computerized mine-monitoring systems. The basic concepts of computerized monitoring are introduced along with its advantages and limitations. Current Bureau projects covering mine-monitoring systems are described, and some of the major areas of concern that should be addressed by future projects are outlined.

Jan 1, 1982

By C. W. Smith

The Bureau of Mines conducted physical and chemical beneficiation studies on three samples of waste investment casting molds to devise a method to liberate and recover zircon. Rod mill grinding, autogenous attrition grinding, and caustic leaching were liberation methods inves-tigated. Flotation, gravity separation, and caustic leaching and sizing were recovery methods investigated. Flotation techniques produced con-centrates containing up to 74.2 pct zircon with a zircon recovery of 53.4 pct. Gravity concentration produced concentrates containing up to 98.6 pct zircon; however, recovery of the zircon was only 57 pct. Caustic leaching and sizing produced concentrates containing up to 98 pct zircon with attendant recoveries of 81 pct.

Jan 1, 1985

By Rose L. Ballard

This chapter summarizes data on crude nonfuel mineral production for the United States, its island possessions, and the Commonwealth of Puerto Rico. Included also are tables that show the principal nonfuel mineral commodities exported from and imported into the United States, and that compare world and U.S. mineral production. The detailed data from which these tables were derived are contained in the individual commodity chapters of volume I and in the State chapters of volume II of this edition of the Minerals Yearbook. Although crude mineral production may be measured at any of several stages of extraction and processing, the stage of measurement used in this chapter is what is normally termed "mine output." It usually refers to minerals or ores in the form in which they are first extracted from the ground, but customarily includes the output from auxiliary processing at or near the mines. Because of inadequacies in the statistics available, some series deviate from the foregoing definition. For gold, silver, copper, lead, zinc, and tin, the quantities are recorded on a mine basis (as the recoverable content of ore sold or treated). However, the values assigned to these quantities are based on the average selling price of refined metal, not the mine value. Mercury is measured as recovered metal and valued at the average New York price for the metal.

Jan 1, 1981

By Steven J. Page

Responding to the increasing concern for dust control in metal and nonmetal mining, the Bureau of Mines investigated typical dust reduction efficiencies of wet bar cutter machines as they are presently being used in salt mines. Wet bar techniques have previously been used in coal mines, achieving dust reduction efficiencies ranging from 11 to 60 pct. Two different wet bar techniques, namely, the front spray and the water trickle, have been studied as they are currently being used in two salt mines. Preliminary results show that the dust reduction efficiencies have a large variation (0 to 66 pct), as is the case for wet bars used in coal. However, whereas wet bars in coal required 3 to 4 gpm water consumption, wet bars in salt obtained similar efficiencies with only 0.1 to 0.4 gpm. The most reliable data obtained during this study show that the front spray system consistently performs at efficiencies between 41 and 66 pct, with an average of 54 pct. The results indicate that, although wet bar cutter techniques in salt mines are a relatively simple and inexpensive means of dust control with a minimum of water consumption, further investigation should be performed to fully evaluate and optimize wet bar cutter dust reduction efficiencies.

Jan 1, 1980

By Warren D. Longwill

All known resources within the four proposed RARE II additions to the Yolla Bolly-Middle Eel Wilderness in northwestern California occur in the Gig Butte-Shinbone study area (fig. 1). No mineral resources are Figure 1.--NEAR HERE. known in the East Fork, Murphy blade, or Wilderness Contiguous units. About 2,400 tons (2,177 t) of subeconomic manganese resources averaging 9.5 percent manganese have been estimated at the Blue Jay Mine in the Big Butte-Shinbone unit. In addition about 9,700 tons (8,793 t) of subeconomic chromium-nickel-cobalt resources in thin laterite soil at the Grubstake Prospect contain about 1.27 percent chromium oxide, 0.45 percent nickel, and 0.03 percent cobalt. Adjacent Ultramafic rock outcrops have pods averaging 2.5 percent chromium oxide (Cr203); one pod contains about 40 tons (36 t) of indicated subeconomic resources.

Jan 1, 1981

By J. K. Whyatt

Researchers at the U.S. Bureau of Mines have been exploring recent advances in the use of strain-softening constitutive laws that approximate shear fracturing. The purpose of these tests is to investigate shear-fracture-related rock bursts in hard-rock mines. The capabilities and remaining problems in the use of strain-softening laws in finite-element, distinct-element, and finite-difference methods are reviewed. Performance of the finite-difference implementation of strain softening is compared to classic experimental results and observations of rock mass behavior in the Coeur d'Alene Mining District of northern Idaho. The results show promise for developing methods to identify the general location and orientation of shear fractures and their sequence of occurrence, but such methods cannot be relied upon to quantify post-fracture loads or displacements accurately. Uncertainty over the amount of energy consumed by failing rock and the dependency of energy consumption on model mesh definition prevent direct application of the results to analyses of rock bursts.

Jan 1, 2010

By Michael Hamilton

Mineral resources have been identified at two properties in the Ten takes RARE II area (table 1). Commodities consist of copper and silver. The deposits, in the northwest part of the study area, are hydrothermal and associated with fissure veins that developed along northwest-striking faults within the Precambrian Purcell Lava. In addition to the identified resources, there is high potential for additional copper-silver resources at these properties and moderate potential for copper-silver-lead-zinc-bariun resources at five others (table 2) in the portion of the study area that is underlain by the Purcell. There is no evidence that significant mineralization occurred in strata above or below the Purcell.

Jan 1, 1983

By Aner W. Erickson

Magnetite iron deposits on Tolstoi Mountain were examined as part of the investigations by the Bureau of Mines of iron and copper ores on Prince of Wales Island. The Tolstoi Mountain project was a part of a program for investigating mineral deposits in Alaska, under the general supervision of R. S. Sanford, acting branch chief.

Jan 1, 1948

By Dorsey A. Lyon

"The ceramic industry of the United States has a total yearly manufactured product of nearly half a billion dollars, despite large foreign importation.After careful investigation of the industry by the Bureau of Mines, it is the belief of those in charge that the usefulness of the industry can be greatly enlarged and the importations greatly lessened through the development of processes that will lead to a greater and better development of the ceramic resources of the United States. This will result in a greater industry with more men employed than ever before, and perhaps a world's supremacy in ceramic trade matters.Investigations in behalf of the ceramic industry are being made at the Bureau of Mines experiment ceramic station at Columbus, Ohio, under the supervision of R. T. Stall, superintendent, who reports a number of instances of practical, beneficial cooperation between the industry and the station during the last fiscal year.Graphite to Crucibles:Prior to 1914, practically all graphite crucibles manufactured in the United States were made from Ceylon graphite bonded with German Klingenberg clay. It was the general belief among graphite crucible manufacturers and users that good crucibles could not be made from American bond clays and graphites.Graphite crucibles were essential for melting certain alloys and special steels urgently needed for the manufacture of war materials. The demand for such metals was so great that it created an unprecedented demand for graphite crucibles.After the European war began no Klingenberg clay could be shipped out of Germany. However, it was fortunate for the cyucibly makers that they had large stocks of Klingenberg clay on hand. When the stock of Klingenberg clay became exhausted, it was necessary for the credible makers to turn their attention to American clays. There were no data or other information available to guide the crucible makers in the selection of good bond clays for their crucibles. It was necessary for them to select their clays more or less by ""guess"", which resulted in the period of service or life of graphite crucibles being shortened 15 to as much as 60 per cent."

Feb 1, 1921

By Gwendolyn D. Hood

The Bureau of Mines investigated techniques for dewatering slurries from talc-processing operations to improve water reclamation and pro-duce dewatered solids suitable for disposal. Various flocculating reagents were evaluated, and a nonionic polyacrylamide was found to be most effective in a specialized flocculation dewatering technique. The flocculation dewatering method was applied in laboratory batch tests and in continuous tests using a static screen, a belt-roller device, and a clarifier-thickener laboratory unit. In continuous tests using the unit, wastes of 3.5 pct solids were dewatered to 56.9 pct solids using 0.03 Ib of flocculant per ton of dry solids treated.

Jan 1, 1983

By Floyd D. Everett

The Cougar Spar property is in southwestern Beaver County, Utah, approximately 35 miles by road northwest of Lund, a station on the mainline of the Union Pacific Railroad (fig. 1). Original fluorspar discoveries on the property were made a. short time before 1941. During 1941 lessees produced approximately 600 tons of ores averaging 40 percent CaF2. Bureau of Mines engineers examined the property in 1942 and recommended development. Work was begun in December 1942 and completed in October 1943. The area was mapped by members of the Federal Geological Survey during the project period. Development included surface trenching; drifting, and crosscutting, a short distance below the outcrop. The surface work comprised a total of 440 linear feet of bulldozer and hand trenches. A total of 550 feet of workings was driven on the 100-foot level. Samples were taken for assay from the trench exposures and from the underground workings as work progressed. Pocks in the area of the Cougar Spar property are igneous and consist mainly of fine-grained tuff and quartz monzonite porphyry. The fluorspar mineralization occurs in a northwest fault zone.

Jan 1, 1951

By D. W. Frommer, M. M. Fine

"INTRODUCTION Laboratory mineral-dressing investigations covered by this report show that ores from Montgomery County, Ark., and Morgan County, Mo., are potential sources of barite and zinc. Fine grinding and froth flotation yielded drilling-grade barite from the former and chemical-grade barite and zinc concentrates from the latter.Samples from these deposits were subjected to a laboratory investigation to develop an economic and feasible treatment. The Arkansas ore, submitted by the Husky Refining Co., consisted of an intimate mixture of the economic mineral and quartz. Fine grinding and fatty acid flotation were utilized to effect a good recovery of a drilling-grade product. The other was a zinc-barite ore submitted by the Rocky Ford Mining Co., Stover, Mo. There was no problem in the recovery of zinc (most of which occurred as sphalerite), but the recovery of barite by flotation was complicated by the presence of gangue carbonates. Ultimately, an excellent recovery of barite was achieved with a relatively new type of flotation promoter, petroleum sulfonate.In recent years, barite has become one of the major industrial minerals as an essential ingredient in heavy drilling fluids, pigments, and chemicals. New sources of this important commodity are always interesting; thus, it is the purpose of this report to present information that may permit commercial exploitation of two deposits not in production."

May 1, 1952

By N. B. Greninger

The U.S. Bureau of Mines conducted explosion tests on various full-scale cementitious bulkheads used in abandoned mine areas to evaluate the ability of the bulkheads to withstand gas explosion over-pressures of 20 psig. Tests were performed on 120-ft2 solid-concrete-block seals of varying thicknesses and designs. Of the seven solid-concrete-block seals tested, only the standard-type seal, having a 16-in thickness, keyed at the floor and ribs, all joints mortared, wedged at the roof, and a center pilaster, maintained its integrity when subjected to a 20-psig pressure wave. After being subjected to repeated explosions, the standard seal only showed a small hairline crack and had an air leakage of 87 ft3/min at a pressure differential of 1 in H2O. Tests were performed on cementitious foam seals of varying thicknesses and compressive strengths. Explosion tests have shown that 200-psi strength, 4-and 8-ft-thick seals can withstand a 20-psig pressure wave. At a pressure differential of 1 in H20, no air leakage was detected through the 200-psi, 8-ft-thick foam seal.

Jan 1, 2010

By Graham W. Mark

A chemical method of analysis for beryllium was developed recently in Bureau of Mines laboratories. In this method, quinalizarin (1-2-5-8 tetrahydroxyanthraquinone) in N/4 NaOH is used as a colorimetric titration reagent. This solution has a reddish-purple color, whereas the solution containing equivalent amounts of beryllium and the dye is rather blue. In the titration procedure, standard quinalizarin solution is added to the unknown beryllium sample and to two standard beryllium samples of different but known concentrations. Then adjustments in concentrations of BeO in the two known and of quinalizarin in all three are made until the red-violet shade of the unknown is halfway between that of the two knowns. The amount of BeO in the unknown is calculated from the known BeO content of the solutions between which it lies. It is extremely difficult to distinguish the slight differences in shade of these solutions without the use of a proper light filter, especially when the concentration is over 0.1 mg. of BeO, so a study was made of the transmission characteristics of quinalizarin in N/4 NaOH and of the corresponding beryllium complex to determine what filter would give the most contrast.

Jan 1, 1950

By V. A. Nieberlein

This paper presents the results of research undertaken to recover titanium and columbium by low-temperature chlorination of low-grade columbium-bearing ilmenite concentrates, and to simultaneously remove chlorinated impurities from the volatile chlorides without resort to distillation. Coke-reduced ilmenite was chlorinated at 400° to 500° C., and the resulting TiC14 was free of most impurities before condensation. A heated purification column was used wherein various packing materials reacted chemically or physically with the impurities which passed through them in the vapor phase. A nearly water-white TiC14 product was obtained directly. The principal impurities in the titanium tetrachloride were: 0.02 percent Fe, 0.01 percent V, 0.05 percent A1, 0.04 percent Si, and 0.07 percent Cb. This is a less pure product than commercial TiC14. Most of the columbium was recovered as crude CbC15, requiring further refining.

Jan 1, 1960