Search Documents

By G. W. Elger

The Bureau of Mines conducted laboratory and larger scale studies on samples of domestic perovskite and ilmenite ore concentrates to devise a procedure for recovering TiC from these ores. From the concentrates, mixtures of titanium and calcium carbides were produced. The carbides were then ground and reacted with water. This reaction decomposed the CaC2 to acetylene and hydrated lime and simultaneously liberated the TiC. Using a combination of elutriation and gravity-separation techniques to separate the hydrated lime, approximately 93 pct of the titanium was subsequently recovered as purified carbide containing 54 to 70 pct titanium with CaO content as low as 0,6 pct. This combination of techniques can be used to separate more than 90 pct of the CaO from the TiC. Therefore, this carbiding procedure is a viable method for treating titaniferous materials, including perovskite, that contain more than 20 pct CaO. Tests made in a static-bed reactor showed that for the reaction of TiC with elemental chlorine to produce titanium tetrachloride (TiCI4), a temperature of at least 940° F is desirable to achieve a suitable extraction of titanium in a laboratory chlorination reactor. In fluidized-bed tests at 840° F, 98 pct of the titanium contained in TiC was extracted.

Jan 1, 1980

By Tobias W. Goodman, George N. Aul, Joseph Cervik

The Bureau of Mines conducted research to degasify a virgin block of coal in the Beckley Coalbed using long horizontal holes drilled in an array from the bottom of a ventilation air shaft. Eight horizontal holes and an in situ pressure hole were drilled in a radial pattern to depths ranging from 418 to 910 ft (127 to 277 m) and 205 ft (62 m), respectively. The investigation showed the shaft was in a basin saturated with water, which resulted in low gas flows from holes. The in situ pressure at 200 ft (61 m) into the coalbed was 79 psig (544.6 KN/m2). The aver- age gas and water flows for the eight holes were 94,100 ft3/day (2,665 m3/day) and 13 gal/min (49.3 l/min) . After 514 days of degasification, 18.7 million ft3 (0.53 million m3) of gas had been drained. Methane face emissions, which were measured as a section advanced toward the shaft, were reduced about 77 pct, emphasizing the value of drainage by this technique. All holes were grouted before the area around the shaft was mined.

Jan 1, 1982

By S. Don Brown

Between 1987 and 1988, the Bureau of Mines studied the mineral resources of the White River National Forest and part of the Arapaho National Forest to appraise the resources present and to determine the types of deposits, and their location, that could be mined economically if sufficient demand and metal prices existed. The study included a comprehensive literature search and a limited amount of field investigation of minerals and mining activity in and near the Forest. This report summarizes a more comprehensive minerals report on the Forests prepared by the Bureau of Mines and was written for a general audience without a background in geology or related fields. Mineral resource information indicates that in the Gore Range-the area between Tennessee Pass and Gilman may contain large base-and precious-metal deposits, and could be the focus of exploration activity in the near future. The Breckenridge mining district was found to have a moderate to high likelihood for mineral exploration and possible development of gold. Recent exploration and minor development work has occurred in several other areas: Montezuma, Kokomo-Tenmile, and Upper Blue River districts, and portions of the Sawatch Range.

Jan 1, 1990

By E. C. Lane

The motor gasoline that is being marketed in the United States this winter is in general, more volatile than that sold a year ago. This increase in volatility is shown by a lowering of the distillation temperatures, ranging from 2°F. at the average initial boiling point to 5°F. at the average end point. During the past eight and. one half years the Bureau of Mines has made semi-annual surveys of the gasoline marketed in the United States, the survey Just completed being the seventeenth in the series. The cities in which samples have been collected, have been chosen as representative of the more important marketing territories, as it is obviously impracticable to obtain a sample of every gasoline sold in the entire country. Samples were collected in Boston for the first time since 1919. It was believed advisable to include samples from that district in order to give a better balance to the survey for the country as a whole.

Jan 1, 1928

By M. N. Plis

This report describes the initial results of long-range research on bit life conducted by the Bureau of Mines. Three commercial bit designs -a round-nose radial, 60° conical, and 90° conical with tungsten carbide (WC) inserts -and five experimental bits were tested. Four of the experimental bits were radial designs using polycrystalline diamond compact (PDC) inserts. The fifth was a 90° conical with an oversize WC insert. Bits were worn on a high-silica sandstone typical of coal mine roofs. The bits were mounted on a 34-in-diam drum section that provided a bit speed of 565 ft/min. Cutting forces were measured on a modified vertical slotter using a three-axis force dynamometer and recorded on an FM magnetic tape recorder. Changes in cutting forces, bit weight, and airborne dust due to gradual abrasive wear and catastrophic insert failure are presented. Tabulated and graphed data, photographs of the progression of bit wear, and selected qualitative visual and auditory observations of the bits taken throughout the experiment are found in the appendixes. The results show that bit life ranged from approximately 16,000 ft for the WC round-nose radial bit to over 125,000 ft for a PDC round-nose radial. Performance, in terms of bit life, cutting forces, wear rate, frictional sparking, machine vibration, and noise was in general best with the PDC bits, followed by the rotating WC bits, with the nonrotating WC bits (round-nose radial and locked 60° conical) being the worst. The results show variations in the included tip angles of new conical bits have an insignificant influence on bit performance when the effects are averaged over the life of the bit. In addition, new bits were generally found to entrain more primary respirable dust for a given cutting distance than worn-out bits. It is hypothesized that this is due to the difference in frictional behavior between new and worn bits. The results from these tests are being used in the Bureau's cutting system model (CSM).

Jan 1, 1988

By Robert F. Randolph

Research on improving haulage truck safety, started by the U.S. Bureau of Mines, is being continued by its successors. This two-part article reports the orientation of the renewed research efforts, beginning with an update on accident data analysis, the role of multiple causes in these accidents, and the search for practical methods for addressing the most important causes. Fatal haulage accidents most often involve loss of control or collisions caused by a variety of factors. Lost-time injuries most often involve sprains or strains to the back or multiple body areas, which can often be attributed to rough roads and the shocks of loading and unloading. Part II will describe research to reduce these accidents, including improved warning systems, shock isolation for drivers, encouraging seatbelt usage, and general improvements to system and task design.

Jun 1, 1997

By Robert F. Randolph

Research on improving haulage truck safety, started by the U.S. Bureau of Mines, is being continued by its successors. This two-part article reports the orientation of the renewed research efforts, beginning with an update on accident data analysis, the role of multiple causes in these accidents, and the search for practical methods for addressing the most important causes. Fatal haulage accidents most often involve loss of control or collisions caused by a variety of factors. Lost-time injuries most often involve sprains or strains to the back or multiple body areas, which can often be attributed to rough roads and the shocks of loading and unloading. Part II will describe research to reduce these accidents, including improved warning systems, shock isolation for drivers, encouraging seatbelt usage, and general improvements to system and task design.

Jan 1, 1997

By Albert W. Deurbrouck

The performance of four sand cones was evaluated by the Bureau of Mines in three preparation plants that utilized cones in various flow schemes. The cone at plant A was a simple two-product one that provided clean coal and refuse. Plant B had two cones; one cone made a primary separation and the other a secondary separation. The primary cone separated salable coal from heavy rejects. The secondary cone separated a low-ash metallurgical coal and an intermediate-ash product suitable for plant fuel or steam markets. In plant C the sand cone was equipped with a middlings draw Which continually removed an intermediate specific-gravity product below the surface of the cone. The three primary separations of raw coal effected between floats and sinks were excellent. The recovery efficiencies for the plus 1/4-inch material ranged from 99.8 to 97.6 percent, the error areas ranged from 19 to 23 square centimeters, and the probable errors in specific gravity ranged from 0.033 to 0.024. The performance data of the two secondary separations varied from excellent in plant B, where the separation was on a par with the primary separations, to somewhat inferior in plant C, where the secondary separation was effected at the middlings draw.

Jan 1, 1965

By George S. Rice, W. L. EGY, H. P. Greenwald, L. M. JONES

CHAPTER I. INTRODUCTION AND SUMMARY. BY GEORGE S. RICE. PREFATORY STATEMENT. This bulletin describes the second series of coal-dust explosion tests conducted by the Bureau of Mines in the experimental mine near Bruceton, Pa. It covers a period from 1913 to 1918, inclusive, of more or less consecutive testing, during which many important conclusions were drawn regarding the way a coal-dust explosion may originate, the mechanism of an explosion, and the methods of pre- venting explosions and of limiting incipient explosions. The manuscript was prepared in 1918, but its publication had to be put aside during the World War for more pressing publications and it was not until this fiscal year 1922 that funds could be allotted for its printing. Meantime the general facts concerning methods of preventing explosions have been made known to the mining industry, with great advantage, it is believed, as explosions of coal dust in mines in the United States have become infrequent. This fact, however, must not lull the consciousness of mining men to the terrible potential danger that lurks in untreated coal dust. The experiments described in this volume should be of aid to them in planning to keep the ever present coal dust in an innocuous condition. The first series-reported in Bulletin 56, "First Series of Coal-Dust Explosion Tests in the Experimental Mine"-included only pre- liminary tests of the ability to start explosions of coal dust under the conditions in the experimental mine. After this fact had been determined and several violent dust explosions had been demon- strated before large audiences of mining men, the work had to be suspended in order that necessary repairs and extensions might be made in the fall and winter of 1911-12. Although the question of the possibility of coal dust causing explo- sions had been considered for more than a century, and much testing in laboratory apparatus and in small surface galleries had been done, coal-mining men generally did not believe that coal dust was explo- sive and considered that fire damp or gases of unknown composition were responsible for the mine explosions that had cost thousands of lives in the various coal-mining countries during the last century. As coal mines increased in number, size, and depth, explosions became alarming in their frequency. Finally came the Courriéres disaster in northern France, 1906, by which 1,100 lives were lost, and the following year in this country, the Monongah mine explosion, in West Virginia, which killed 361 men, and the Darr explosion, in Pennsylvania, which killed 239 men. These two disasters, both in December, 1907, led Congress to make an appropriation for an in- vestigation of the causes of mine explosions. The funds became available July 1, 1908, and the work was placed under the United States Geological Survey's technologic branch, with the late Dr. Joseph A. Holmes in charge. Before undertaking the investigations Dr. Holmes visited Europe, accompanied by the senior author of this bulletin, to study the methods foreign countries used to prevent mine explosions, to obtain details regarding tests being made in several countries, to procure safer explosives and better safety lamps for use in gaseous and dusty mines, and to study the methods used in coal-dust explo- sion tests in the recently completed galleries at Altofts, England, and Liévin, France, and in the older galleries at Gelsenkirchen, Germany, and Frameries, Belgium. At all of these stations the explosions tests were made in surface galleries. The Austrian gallery at Segengottes, near Brünn, Moravia, visited by the writer in 1911, is an underground gallery, but the testing done in it was limited, dealing with ignition of coal dust rather than with propagation. Although the results obtained in the foreign galleries had indicated that coal dust was explosive, mining men in the respective countries were of the opinion that the dust would not explode under mine con- ditions. This situation led Dr. Holmes to the conclusion that testing must be done in a real mine, to make certain that the conclusion would be reliable and would be accepted by the mining public as decisive.

Jan 1, 1922

By R. T. Sorensen

Bench-scale and continuous testing were performed to adapt the anionic process for flotation of calcium activated silica to the fine-grained hematitic-goethitic jaspers from the Marquette range, Michigan. These ores typically contain about 35 percent Fe and require grinding to about 80 to 100 percent minus 400 mesh to insure an adequate liberation of gangue from the iron oxides. A method for removal of troublesome slime fractions without excessive iron loss, by first dispersing the quartz and then selectively flocculating the iron oxides, was evolved in the laboratory and successfully accommodated to pilot plant practice. The efficiency of the flotation process was improved with respect to both reagent usage and concentrate grade and recovery by using the selective flocculation-desliming technique as a pretreatment. The benefits of the combined desliming-flotation procedure were most evident in pilot plant processing. The best tests on two ores yielded recoveries of about 84 percent in concentrates containing 65.1 percent Fe and 4.8 percent SiO2 and 66.2 percent Fe and 3.9 percent SiO2, respectively. These results are in comparison to recoveries about 10 percent lower than the above to concentrates containing 63.9 percent Fe and 6.6 percent SiO2 in the one instance, and 63.6 percent Fe and 7.2 percent SiO2 in the other, obtained by flotation without the prior desliming treatment.

Jan 1, 1967

By James P. May

Operating mine haulage trucks near the crest of stockpiles and waste dumps is a potentially hazardous practice often resulting in a localized slope failure and a dump point accident. The U.S. Bureau of Mines has developed a computer code (INSLOPE3) based on the kinematic method of limit analysis which determines an admissible truck weight (upper bound value) for varying distances from the slope edge. The program considers the material strength parameters, slope geometry, and inertial forces induced by vehicle braking. The program can be utilized to assist in the determination of safe operating distances for a haulage truck from a slope edge, the development of safe vehicle operating procedures, and the admissible weight for a static concentrated loading near the crest of an otherwise stable slope. This report provides information on the use of INSLOPE3, interpretation of the results for mining applications, and instructions for acquiring a copy of the software.

Jan 1, 1991

By Jr. Watts, B. K. Cantrell, D. H. Carlson, K. L. Rubow

"The use of diesel equipment in underground coal mines is controversial because ""whole diesel exhaust"" is regarded as ""a potential occupational carcinogen"" by the National Institute for Occupational Safety and Health (NIOSH). Threshold limit values (TLVs) are recommended for the gaseous pollutants; CO, CO2, NO, NO2, SO2, and some hydrocarbons emitted in diesel exhaust. There is, however, no TLV recommended for diesel exhaust aerosols (DEA) nor is there a standard method for sampling these aerosols.The University of Minnesota and the Bureau of Mines have collaborated to develop a personal diesel exhaust aerosol sampler (PDEAS) which utilizes size selective, inertial impaction and gravimetric analysis. During the field tests of this sampler, numerous air quality measurements were conducted in underground coal mines using diesel equipment. The objective of this report is to present these data and to assess the impact of diesel face haulage equipment on mine air quality.Air quality data were collected in four underground coal mines using continuous mining methods with diesel haulage equipment. Daily samples were collected at the section intake, haulageway, and on haulage vehicles. Both full-and partial-shift samples were collected using a variety of aerosol instruments, including the PDEAS and the micro-orifice, uniform deposit impactor (MOUDI) which sample the mine aerosol diesel exhaust fraction. Two of the mines were also monitored for the major gaseous constituents found in diesel exhaust CO, CO2, NO, NO2, and SO2. These measurements were made by either collecting bag samples for subsequent gas analysis or by Palmes dosimeters.The concentrations of CO, CO2, NO, NO2, and SO2, were well below regulated levels. The mine average DEA concentration determined by the PDEAS in the haulageway for the three mines surveyed using this instrument was 0.79 mg/m3, with a standard deviation of 0.19 mg/m3. DEA contributed 65% of the respirable aerosol, at this location. These results were the same as the mean DEA concentrations calculated from size distribution measurements obtained using the MOUDI. This was 0.78 mg/m3, with a standard deviation of 0.22 mg/m3."

Mar 1, 1992

By W. P. Haynes, A. J. Youngblood, J. J. Demeter

Synthesis of high - Btu gas , using the Fischer - Tropsch reaction was investigated in a tube - wall reactor of 2 - inch steel . The catalyst was carbonexpanded iron ( CEI ) , formed on the walls of a steel reactor by exposing the reactor to 1H₂ + 100 synthesis gas under certain conditions . Advantages to be gained from successful development of the CEI - coated tube- wall reactor are elimination of catalyst plant and catalyst handling and charging operations , high- temperature operation , and a relatively low- cost , reactor -heat recovery system . In one test ( TW- 8 ) in which the reactor was filled with CEI , the reactor was operated for 1,910 hours before the test was stopped because of excessive pressure drop caused by carbon deposition . The pressure drop was satisfactory for 1,000 hours of operation at an hourly space velocity of 300 , but it increased rapidly at space velocities of 600 and 1,000 . When operated at a space velocity of 300 , with a ratio of 1 to 1 recycle at 534 ° C , a conversion of 72 percent of the 3H + 100 synthesis gas was achieved . The product gas had a heating value of about 610 Btu per cubic foot and could be suitably upgraded to 900 - Btu gas by subsequent use of a nickel catalyst . CEI did not operate effectively as a film catalyst under conditions of generation tried in this study . Generally , operation of the 2 - inch reactor with CEI catalyst was unsatisfactory because of poor reproducibility of the activation step and poor temperature control resulting in high- operating temperatures and eventual plugging of the reactor . Tests using CEI in fixed , packed beds suggest that the most likely application for CEI in producing high - Btu gas would be a moving - bed reactor , where sufficient bed movement and heat removal are provided to prevent plugging .

Jan 1, 1964

By R. Hogg

"The basic population balance models for agglomeration processes are reviewed and procedures are described for extending their applicability to systems with size-dependent rate constants and to the formation and growth of porous agglomerates from rigid, solid particles. Simplified procedures for the further extension of the models to include simultaneous agglomerate growth and breakage arc also described. IntroductionThe association of small particles into clusters or agglomerates is a significant factor in many facets of particle processing. Agglomeration processes are widely used to facilitate handling, storage and utilization of fine powders. Processes such as coagulation or flocculation are used to aid solid-fluid separation in dispersed particulate systems. Agglomeration also occurs as an accompaniment, often unwanted, to other particulate processing operations such as fine grinding, mixing and blending, transport and flow.Reliable agglomeration models are needed for improved understanding of the processes in general and of the complex role of numerous, interacting variables as well as for direct application to the design and control of industrial processes such as flocculation, granulation and pelletization. Ideally, the models should account for the primary forces responsible for agglomerate ·formation and growth, the effects of external forces on process dynamics, the development of agglomerate structure and its role in the process itself, and the effects of concurrent processes such as structure modification (e.g. compaction) and agglomerate breakage or degradation.In its most general form, the process of agglomeration involves taking discrete, independent particles, bringing them into contact with one another, promoting (or allowing) interparticle adhesion to occur and then causing structure rearrangement, usually under the action of external forces. The relative importance of these steps varies with the nature of the particulate system being agglomerated and with the kinds of agglomerates being produced. Coagulation or flocculation of particles dispersed in fluids is generally dominated by the contact and adhesion steps. In the granulation of powders, on the other hand, particles are already in contact so that structure rearrangement is the principal step."

Mar 1, 1992

By W. A. Stickney, J. W. Town

Batch and continuous - circuit flotation , leaching , precipitation , and electrodeposition studies were made by the Bureau of Mines to determine optimum conditions for treatment of complex mercury - antimony sulfide and mercury- arsenic sulfide ores and concentrates . On the Red Devil ore sample over 95 percent of both the mercury and antimony sulfides were recovered in a flotation concentrate containing 35.6 percent mercury and 21.0 percent antimony . By selective flotation a mercury concentrate containing 71.0 percent mercury and 2.9 percent antimony was obtained with a mercury recovery of 90.4 percent . Leaching results show that , with 150 grams per liter of sodium sulfide and 50 grams per liter of sodium hydroxide , 95 to 99 percent of the mercury , antimony , and arsenic sulfides could be extracted from the concentrates treated . Sodium hydroxide reagent consumption was based on the sulfides generated in the dissolution of the sulfide minerals and on the method of metal recovery used . Selective leaching of the antimony and arsenic sulfides with potassium sulfide dissolved more than 95 percent of either of these two sulfides and 0.5 to 5 percent of the mercury sulfide present . Methods for recovering mercury and antimony from solution were electrodeposition of mercury followed by electrodeposition of antimony , aluminum precipitation of both mercury and antimony , or antimony precipitation of mercury followed by antimony electrodeposition . The method used in recovering the mercury depended on the mercury- antimony content of the solution being treated .Batch and continuous - circuit flotation , leaching , precipitation , and electrodeposition studies were made by the Bureau of Mines to determine optimum conditions for treatment of complex mercury - antimony sulfide and mercury- arsenic sulfide ores and concentrates . On the Red Devil ore sample over 95 percent of both the mercury and antimony sulfides were recovered in a flotation concentrate containing 35.6 percent mercury and 21.0 percent antimony . By selective flotation a mercury concentrate containing 71.0 percent mercury and 2.9 percent antimony was obtained with a mercury recovery of 90.4 percent . Leaching results show that , with 150 grams per liter of sodium sulfide and 50 grams per liter of sodium hydroxide , 95 to 99 percent of the mercury , antimony , and arsenic sulfides could be extracted from the concentrates treated . Sodium hydroxide reagent consumption was based on the sulfides generated in the dissolution of the sulfide minerals and on the method of metal recovery used . Selective leaching of the antimony and arsenic sulfides with potassium sulfide dissolved more than 95 percent of either of these two sulfides and 0.5 to 5 percent of the mercury sulfide present . Methods for recovering mercury and antimony from solution were electrodeposition of mercury followed by electrodeposition of antimony , aluminum precipitation of both mercury and antimony , or antimony precipitation of mercury followed by antimony electrodeposition . The method used in recovering the mercury depended on the mercury- antimony content of the solution being treated .

Jan 1, 1964

By C. H. Riggs

This report presents pertinent data on all active water-flooding projects in Washington County, Okla., and describes in detail the operation and production history of five representative floods. The flooding of partly depleted oil-bearing sands to produce petroleum that would not be recovered by other methods is becoming increasingly important to the oil industry. In 1942, two water-flooding projects in Washington County produced 35 barrels of oil daily from 90 developed acres. In March 1951, 4,000 barrels of oil was being produced daily by the injection of 58,000 barrels of water on 19 active projects covering 1,645 acres. Several projects are being extended, and new operations are being initiated. Figure 1 shows the location of the active water-flooding projects in Washington County. The yearly oil production from Washington County increased from 1,076,000 barrels in 1948 to 1,720,000 barrels in 1950, owing principally to the effects of water flooding. To March 1951, permits to flood more than 8,000 acres in Washington County had been granted by the Oklahoma Corporation Commission.

Jan 1, 1951

By Charles K. Rose

The Cebolla Creek titaniferous iron deposits near Powderhorn in southern Gunnison County, Colo., were examined by the Federal Bureau of Mines as part of an overall program to investigate the Nation's titanium and iron resources. The deposits occur around the periphery of the Iron Hill stock, which underlies an area of about 12 square miles. Concentrations of magnetite, ilmenite, and perovskite arc localized along fractures in the pyroxenite stock. Mineralogical studies of composite surface samples collected in 1956 showed that most of the iron is present in ilmenite-bearing magnetite. Perovskite is the chief titanium mineral in the magnetite-rich and augite-rich types, and sphene is the principal titanium mineral in the placer material. The mica-rich rock contains approximately equal amounts of perovskite, ilmenite, and sphene.

Jan 1, 1960

By Kenneth J. Miller

To determine the effectiveness of the many new flocculants available to the coal industry 20 of these reagents were evaluated treating slurry feeds to four refuse thickeners. Settling rates and supernatant liquid clarities were determined for each of the flocculants on the four slurries, and zeta potential measurements of the slurry solids were made. The test results showed that the flocculants provided comparable results when judged categorically as anionic, nonionic, or cattonic. It was also apparent that control of zeta potential insures maximum benefit from a flocculant.

Jan 1, 1968

By Synthia N. McIntosh

The U.S. Bureau of Mines investigated the feasibility of using ammonium carbamate (NH2CO2NH4) leaching to recover manganese from steel plant slag. This investigation showed that treatment of the slag in hydrogen prior to leaching enhanced manganese extraction. Up to 80 pct of the manganese and 50 pct of the iron could be extracted from a silicon steel slag that had been pretreated in hydrogen at 700° C. Two 4-h leaching stages conducted at ambient temperature with a solution containing ammonia and carbon dioxide dissolved manganese and iron as their carbamate complexes. Heating the pregnant solution to 65° to 85° C decomposed the complexes and precipitated the metals as insoluble carbonate salts. Ammonium carbamate leaching of other slags from several steelmaking plants produced lower manganese extractions, which suggests that the method cannot be applied satisfactorily to all steelmaking slags

Jan 1, 2010

By W. C. Smith

This Bureau of Mines report discusses how pull-test data can help establish polyester resin column length criteria for roof bolts in evaporite minerals. The study evaluates the effectiveness of partial to full columns of resin in anchoring 4-ft, No.6, grade 40 rebar roof bolts in potash, salt, trona, gypsum, and borate mine roofs. Pull tests were performed on over 600 roof bolts in 11 evaporite mines. Column lengths ranging from 6 to 48 in (fully grouted) were evaluated for each test site. In general, comparative results among all test sites indicate that pull-out loads in excess of 10 tons (force) were attained with resin-grouted bolts having 13 to 75 pet less than a full column of polyester resin. Ten tons (force) of load-carrying capability compared favorably, in terms of strength, with the calculated yield strength of the rebar used in the tests, which was 8.8 tons (force). The site-specific nature of each test site, due to the unique combinations of geology, mine-induced stresses, and other unknown parameters, prevented the establishment of valid generic column-length criteria. For these reasons, data to evaluate resin-column-length effectiveness are best obtained on a mine-specific basis.

Jan 1, 1987