Search Documents

By Worthen Bradley

This paper describing the metallurgical practice and costs at the reduction plant of the. Sulphur Bank Syndicate, Clearlake, Calif., is one of a series of papers on the treatment of ores being prepared by the Bureau f Mines. The reduction plant and mine of the Sulphur Bank Syndicate are on the eastern shore of Clear Lake, in Lake County, Calif., 4 miles from the town of Clearlake and 125 miles north of San Francisco.

Jan 1, 1931

By Jack I. Paige

The Bureau of Mines conducted studies to provide data on the room temperature mechanical properties of Ti-6Al-4V alloy cast in waterglass-bonded zircon sand and to determine the effect of hot iso-static pressing (HIP) on these properties. Data on the cast and annealed Ti-6Al-4V alloy were compared with published data for forged and investment-cast Ti-6Al-4V alloy. The average Charpy V-notch impact strength compared favorably with the typical values of 17 ft?lbf for wrought material and 19.2 ft?lbf for investment-cast material. The room temperature mechanical proper-ties of cast and annealed material compared favorably with published values for investment-cast Ti-6Al-4V alloy and exceeded the specifications for (1) titanium and titanium alloy castings, grade C-5 according to ASTM B367-69, and (2) titanium alloy bars and forgings as specified in AMS4928H, except for the AMS4928H minimum requirement for reduction in area (25 pct). The minimum requirements are: tensile strength, 130 ksi; yield strength, 120 ksi (0.2 pct); and elongation, 6 pct. None of the specimens tested met the AMS4928H minimum requirement for reduction in area. The HIP process healed the internal casting porosity in the test specimens, but the fatigue strength was not significantly improved. The fatigue properties of both the cast and cast plus hot isostatically pressed castings were significantly lower than those of wrought products.

Jan 1, 1984

By Stephen C. Tadolini

The Bureau of Mines conducted field investigations in two underground mines to determine the actual loads to which bearing plates were subjected when installed in conjunction with full-column resin-grouted bolts and the roof movements generated by the applied loads. Measured loads indicate that the bearing plate is an integral part of the support system. Vertical displacement gauges installed to monitor roof displacements in the test sites show that the highest degrees of loading occur in conjunction with the largest amounts of movement.

Jan 1, 1986

By Helen E. Edwards

The Bureau of Mines is engaged in a systematic evaluation of the thermodynamic properties of combustion gases. These studies are designed to provide basic thermodynamic information of high accuracy facilitating the theoretical study of flame and combustion phenomena. This report is the third of a series3/ presenting results of the study for particular fuel-oxidant systems. The equilibrium composition of the products of combustion and the adiabatic flame temperatures of specified oxyacetylene systems have been computed.

Jan 1, 1953

By Sabri Ergun

Previous studies of magnetic separation of pyrite from coals have been reviewed critically. Magnetic susceptibilities of United States coals of differing rank have been measured. The effects of crushing, magnetic mixing, drying, weathering, and heat treatment on the enhancement of the magnetism of pyrite have been analyzed. The importance of size distribution of pyrite in the coal and the necessity of crushing to liberate the pyrite has been discussed. It has been found that the inherent susceptibilities of the carbonaceous, mineral-free portions of coals (? -0.5 X 10-6 in cgs units) and of relatively pure pyrite isolated from coals (? -0.3 X 10-6) do not permit efficient separation of pyrite from coal; the average susceptibility of the magnetic fraction of coal must be raised to 3 X 10-6. Friction forces encountered in crushing sedimentary pyrite embedded in coal do not increase its susceptibility. Subsequent weathering or heat treatment below 400° C leads to the formation of iron sulfate and hence increases the effective paramagnetism of pyrite. Ferromagnetic compounds of iron are not formed in significant quantities at temperatures below 400° C. The degree of liberation and apparent susceptibility of pyrite are the most important parameters in its separation. It is concluded that effective beneficiation of coals can be achieved by magnetic separation. A sufficient increase in the susceptibility can be achieved by converting less than 0.1 percent of pyrite into ferromagnetic compounds of iron. Such conversions occur only at temperatures >500° C. An investigation of the dielectric properties of coals and pyrite in the frequency range 0.1 to 60 Mhz indicates that the imaginary dielectric constant of the pyrite is about 100 times larger than that of coal. Exploratory experiments indicate that pyrite can be selectively heated to temperatures above 500° C without appreciable rise in the temperature of coal. It appears that dielectric heating of coals in the Ghz frequency range is the most feasible method of enhancing the paramagnetism of pyrite.

Jan 1, 1968

By E. Morrice

The Bureau of Mines investigated methods for beneficiating platinumgroup metal ores from the Stillwater Complex , Montana , as part of its program to increase the supply of critical and strategic minerals and metals from domestic resources . This report presents results of a 5- day continuous campaign employing a pilot flotation mill to recover sulfide concentrate containing platinum- palladium values from anorthositic ore . A mercaptobenzothiazole - sulfuric acid reagent suite was used . The pilot flotation mill was operated at an average feed rate of 106 lb/ hr of ore . A rougher concentrate containing 8.5 pct of the feed was prepared ; it assayed 1.1 oz /ton Pt and 3.5 oz / ton Pd . Recovery of platinum and palladium were 91 and 87 pct , respectively .

Jan 1, 1965

By Raymond O. Dannenberg

The Bureau of Mines conducted laboratory and full-scale tests to develop a process for improving the flotation characteristics of lime-treated waste water produced by the Kennecott Copper Corp., Magna, UT. Unknown substances in the waste water reduced the flotation efficiency of the metal sulfides. An estimated annual loss of 795,000 lb Cu, 232,000 lb Mo, 5,625 tr oz Ag, and 617 tr oz Au would result from recycling the total flow from the lime treatment plant to the flotation mill in an effort to conserve water and reduce associated expense. The tests indicated that aeration or treatment with activated carbon significantly improved the water quality. The improvements in molybdenum recovery averaged 8 pct for carbon, 11 pet for activated carbon, and 16 pct for combined aeration and activated carbon. The combination of the two processes produced water quality as good as or better than normal feed water.

Jan 1, 2011

By Maurice Deul

A special short-term research project was initiated to develop plant design parameters for treating mine waters to yield an effluent acceptable for discharge into streams and a sludge amenable to effective and economic disposal. Neutralization was investigated to provide simple and direct treatment of ferruginous acid waters using lime; coarse limestone, and limestone followed by lime. Limestone treatment was accomplished using a small cement mixer as a simple reactor to provide abrasive agitation of limestone and mine water. Results from tests with nine mine waters encompassing a wide range of iron and acid concentrations showed that coarse limestone, one of the cheapest neutralizing agents known, is potentially useful for treating mine water discharges. However, process variables must be defined more completely before the practical applications and limitations of the process can be fully established. In all the tests a pH of >7.2 was obtained ultimately with limestone. Reaction time to reduce the iron content below 7 ppm in the water was dependent on the original ferrous iron concentration. For waters with high ferrous iron content, treatment with limestone followed by lime rapidly produced an acceptable treated water, Sludges with good settling and handling characteristics resulted when limestone was used for neutralization either alone or with subsequent treatment. Reaction rates are expressed graphically as pH change and iron depletion curves; characteristic solids settling curves are shown. The temperature dependency of ferrous iron oxidation was verified.

Jan 1, 1967

By S. M. Shelton

Preliminary work in the investigation of electrolytic manganese, as reported J, showed promise for a practical procedure of continuous production. Laboratory work was continued in the direction of process simplification to determine an economically feasible procedure that mould require a minimum of expensive equipment for plant erection and a minimum of regent consumption for operation. Results furnished enough evidence to indicate that modifications of the process could be made leading to simplified procedure and with no sacrifice in operating efficiency. A supply of at least 200 pounds of the metal was desired for alloy research, and it was believed worth Mile to utilize available facilities in a search for difficulties, that were not encountered in the laboratory and that might arise in larger-scale operation. Consequently, an experimental pilot plant was erected. The plant was designed for a capacity of 15 rounds per day of metal and operated under simulated -plant practice.

Jan 1, 1938

By J. T. McCartney

The Bureau of Mines has developed an automated reflectance scanning microscope system, primarily for determination of volume proportions, size distribution, and mode of association of the physical (petrographic) components of coals. The process, which is potentially more rapid and objective and less tedious than a visual microscopic procedure, involves magnetic tape recording of several millions of reflectance readings on micro-meter sized areas of polished coal surface and computer analysis and interpretation of some characteristics of the coal components. The system was tested in a study of pyrite distribution in steam coals. The application was essentially successful, but defects in polished pyrite surface characteristics and problems in adequate sampling prevented completely satisfactory results. Pyrite con-tent and coal-pyrite particle association could be determined nearly as well as by visual microscopy, but size distribution data were less acceptable.

Jan 1, 1969

By E. R. Palowitch

This report stems from a study by the Bureau of Mines of the possibility of reducing coal filter-cake moisture by applying radiant heat directly to the filter cake while under vacuum during the drying phase of the filter cycle. One disk of a 4-foot-diameter vacuum filter was equipped with gas-fired radiant-heat generators and the effect of radiant heating on the moisture content of a variety of filter cakes was studied. The results of this investigation show that this process can best be described as a filter aid capable of increasing the effectiveness of conventional filtration approximately 6 percentage points of moisture. The operating cost of removing water by this method is somewhat lower than the average operating cost of thermal drying and is considerably cheaper when the total cost is considered. Removal of water from coal that has been wet-cleaned is an important part of the overall coal preparation process. Water is a contaminant, and it is foolish to wash coal to reduce its ash content and add inert water in the process. In some instances the removal of water is actually more important than the removal of ash-forming minerals; its weight adds to the cost of transportation, and its evaporation during burning or carbonizing absorbs useful heat. Fine coal that contains more than about 10 percent moisture is notoriously difficult to handle. A problem thus exists for which there are sound practical and economic reasons to seek a solution.

Jan 1, 1961

By A. T. Coumbe

The first national survey covering sales of fuel oil by States and principal uses was made in 1926 by E. B. Swanson of the Bureau of Mines (then under the U. S. Department of Commerce) under a cooperative agreement with the American Petroleum Institute. This annual study, covering the market for fuel oil, was made through 1930 with the financial help of the institute bat has since been continued by the Bureau up to the present time. The scope and coverage of the survey have gradually changed over the years as new uses for fuel oil have been found and new products have come into importance resulting in market expansion. Range oil (No. 1 fuel oil or kerosine) came into use for cooking and space-heating daring the depression era in New England, and it was first reported as a total in the 1931 survey. In 1934 the sales were compiled on a State basis. State totals for distillate fuel oil, Diesel fuel, and residual fuel-oil sales were first shown for 1934 and by principal uses and States in 1937. Kerosine deliveries by States and main uses were also released for the first time in 1937.

Jan 1, 1952

By S. P. Holt, Robert S. Sanford

"INTRODUCTION The wartime demand for iron ore and alloy steel on the west coast revived interest in iron reserves in western United States and Alaska. Magnetite was known to have been the most abundant metallic mineral at some of the old copper mines on Prince of Wales Island. In the summer of 1942, the Bureau of Mines began a program of preliminary investigation followed by core-drilling two magnetite deposits on the island.The Poor Man iron deposit on Kasaan Peninsula, Prince of Wales Island, Southeastern Alaska, was examined in August 1942 by Robert L. Thorne, associate mining engineer of the Bureau of Mines, and John C. Reed and B. N. Goddard, geologists of the Federal Geological Survey in September 1942 the area was mapped geologically and a magnetic survey was made by the Geological Survey. In October and November 1942, a more thorough preliminary examination, which included cleaning out and sampling old adits and trenches, was made by thesenior author, Robert L. Thorne, and Aner W. Erickson, engineers of the Bureau. J. G. Shepherd, a consultant of the Bureau, spent two weeks in March and April 1943 investigating the Poor Man and other deposits on Kasaan Peninsula. Core drilling was completed in June 1943.L. A. Warner, of the Geological Survey, examined all cores and interpreted structural data revealed by the drilling."

Oct 1, 1946

By G. W. Jones, F. E. Scott, R. E. Kennedy

Methylene chloride , dichloromethane CH2C12 , a low - boiling and highly volatile organic chlorinated compound, is used extensively as a refrigerant in air conditioning installations , as an intermediate in organic synthesis , and as a solvent for cellulose acetate and other materials . As its vapors are not inflammable in air at ordinary temperatures , it can be used to advantage where it would be highly dangerous to use ordinarily inflammable solvents . The question has been raised as to its inflammable range in pure oxygen and in air enriched with oxygen . To find the answer to this question, tests were carried out with various mixtures of methylene chloride , oxygen, and nitrogen mixtures . It was found that methylene chloride has wide limits of inflammability in pure oxygen . Additional tests were then made to establish the complete range of inflammability of these gases . The methylene chloride employed in the tests was cbtained from the Eastman Kodak Co. It had a reported boiling range of 40.5 ° to 42.0 ° C. and a density of 1.322 at 20 ° C.

Oct 1, 1943

By Seth C. Scharfer

"As part of the Bureau of Mines effort to provide thermodynamic data for the advancement of mineral technology, the Gibbs energies of formation of MoS2 (molybdenite) and WS2 (tungsten disulfide) were determined with high-temperature galvanic cells employing stabilized Zr02 (zirconia) as the electro¬lyte. In the temperature range from 867 to 1,209 K, potential measurements were obtained for the cellPt, MoS2 , Mo02 , SO2 = 1 atm // Zr02 // 02 = 0.0112 atm, Pt, with the overall cell reactionMoS2(c) + 3 02(g, 0.0112 atm) = Mo02 (c) + 2 S02(g). (1)These results, combined with the best available values for Gibbs energies of formation (?G°f) of Mo02 (molybdenum dioxide) and SO2 (sulfur dioxide) from the literature, give the standard Gibbs energy of formation of MoS2, ?G°f, for the reactionMo(c) + S2(g) = MoS2(c) (2)?G°f = -96.681 + 43.76 x 10-3T±0.538 kcal/mole, (3)where temperature (T) is expressed in Kelvins.Similar measurements in the temperature range from 872 to 1,210 K were obtained for the cellPt, WS2 , W03 , SO2 = 1 atm // Zr02 // 02 = 0.0114 atm, Pt, with the overall cell reactionWS2(c) + 3.5 02(g, 0.0114 atm) = W03 (c)+ 2 S02(g). (4) Combination of these results with the best available data of ?G°f for W03 (tungsten trioxide) and SO2 from the literature gives the Gibbs energy of formation of WS2 in the temperature range from 872 to 1,210 K for the reactionW(c) + S2(g) = WS2 (c)(5)?G°f = -92.429 + 43.88 x 10-3T ± 0.280 kcal/mole. (6)A third-law analysis yields a standard enthalpy (?H°f) for the reaction298Mo(c) + 2 S(rh) = MoS2(c), (7)?H°f = -67.36±0.60 kcal/mole, (8)298where the standard states are pure crystalline MoS2 / and rhombic sulfur."

Jan 1, 1980

By E. J. Lintner

This paper is one of a series being prepared by the United States Bureau of Mines describing clay mining and crushing methods and costs at various operations throughout the United States. These papers are designed to disseminate technical information regarding methods used. The cost tabulations represent local operating expenditures only and not total production costs. It is recognized that publication of total production costs might perhaps, in many instances, cause embarrassment to the individual operator as well as to the industry as a whole. On the other hand, operating costs are essential to the technical discussion and study of the methods employed. The attention of the reader is specifically called to this distinction in order that no misunderstanding of the scope of the cost tabulation shall ensue. The following report deals specifically with the methods employed by the Camp Brothers Company, Mogadore, Summit County, Ohio.

Jan 1, 1936

By J. A. Ruppert

The Bureau of Mines investigated methods of refining iron-contaminated zinc to marketable quality and developed a laboratory-scale process in which aluminum, added as a refining agent, reacted with the iron, forming solid Fe2Al which floated to the surface of the melt. Solids were separated by both filtration and centrifugation, using a unique type of "dipping" centrifuge devised during the work. Typical zinc recovery was 95 percent, and iron content of the metal was lowered from 0.37 to 0.02 percent.

Jan 1, 1967

By James L. Eirls

The objective of this project was to improve a driver's field of view for large trucks used in the mining industry. Rearward viewing was enhanced by improving the rear-view mirror designs. Rear vision was accomplished using a closed circuit television system. Views ahead,, to the right, and downward were obtained with a blind area viewer (BAV). The BAV is a unique combination of fresnel lenses housed in a shielded, environmentally protected enclosure that produces an image of the area in front of and downward 70° and to either side of the BAV 300. The improved visibility devices were evaluated by long-term, in-mine testing. The right Bide mirror (RSM) and BAV provide the greatest improvements for the least cost and are commercially available. Application of the RSM and BAV should achieve a reduction in accident potential and greater vehicle productivity by enlarging and improving the equipment operator's visibility and making priviously blind areas and hazardous situations detectable.

Jan 1, 1982

By Gopala N. Krishnan

The most promising candidate for the recovery of alumina from non-bauxitic sources is the leaching of clay by HCL acid followed by crystallization of aluminum chloride hexahydrate (ACH) by hydrogen chloride sparging. Hydrothermal precipitation of boehmite ( ?-A100H) from aluminum chloride solution will simplify the process, will reduce energy consumption and will eliminate corrosion problems involved in calcination of ACH to obtain alumina. This report summarizes the results of Phase I of a program to study the precipitation of boehmite from AlC13 solutions. The amount of boehmite precipitation from dilute A1C13 solutions (5 wt%) is . negligible below 200°C. Above 200°C the precipitation increases with increasing temperature approaching 40% at 300°C. Addition of HCl acid to the dilute A1C13 solution even in small quantities drastically reduces boehmite precipitation. Solution impurities such as Fe, Ca, Mg, or Na substantially promote the precipitation of boehmite. No precipitation is observed from concentrated A1C13 solution (30wt%) representing the leach liquor.

Jan 1, 1980

By Roy C. Bartholomae

An accurate characterization of the vibration environment and a vibration qualification test derived from it will be a very useful tool for manufacturers of instrumentation for use on underground coal mining equipment. Recognizing this, the Bureau of Mines sponsored a study wherein vibration levels were measured on mining equipment to form a basis for developing the required vibration test. The data base was composed of 160 samples taken at different positions on a variety of underground machinery. The data were analyzed and presented in a format typical of military vibration qualification tests. The form was shown to be virtually identical to the swept sine test envelope specified in MIL-STD-810B for tracked vehicles.

Jan 1, 1982