Search Documents

By James S. Browning

The Bureau of Mines conducted laboratory batch and small-scale continuous flotation tests of weathered mica pegmatite ores from Alabama and North Carolina to determine the technical feasibility of recovering commercial-grade mica concentrates. A new anionic-catonic method was developed for recovering mica in the presence of clay slimes. In continuous tests, concentrates containing 98.1 percent mica were obtained from the Alabama pegmatite ore; the North Carolina pegmatite ore concentrates contained 97.2 percent mica. The recoveries were 83.8 and 81.6 percent, respectively.

Jan 1, 1965

By David A. Monaghan

This report describes instrumentation which is part of a system for extinguishing mine fires by pumping material through surface boreholes in order to seal off all underground passageways leading to the fire area. Major instrumentation systems include a closed circuit television probing system and an acoustic seal checking system. The latter consists of a speaker probe, a receiver probe and related signal processing equipment. All probes can be winch-deployed down a 6-inch diameter borehole. The CCTV unit can be rotated 360 degrees in the horizontal plane, and contains sufficient lighting to reliably assay conditions for sealing or rescue within a 200 foot radius. The acoustic seal checker monitors the completion of a seal as it progresses by use of probes lowered through boreholes on either side of the seal.

Jan 1, 1977

By Larry A. Haas

The Bureau of Mines is investigating the use of complex gas mixtures, such as would be produced by coal gasification, for reducing iron oxide pellets. A semiempirical model was developed to predict a priori the reduction rate of an iron oxide pellet in a laboratory tube furnace with simulated coal gases at a total pressure of 1 atm. The model uses partial pressures of H2, CO, CO2, CH4 (methane), water vapor, and a temperature-dependent term to predict the rate of reaction. The reduction rate (weight loss per unit of time) was determined with a thermo-gravimetric apparatus (TGA) in the temperature range of 800° to 1,100° C. The ranking of the reductants, in order of decreasing reducing potential, is H2, CO, and CH4 at temperatures between 800° and 1,000° C; however, CH4 became a better reductant than CO at 1,100° C. Water vapor did not decrease the reduction rate as much as did CO2, Carbon deposition was observed at temperatures below 1,000° C with gas mixtures with high CO and low H2 concentrations. With low-Btu gas at 900° C, over 90 pct of the iron oxide was reduced to iron in less than 3 h. This com-pares with a reduction time of 1.5 h with medium-Btu gas and 1 h with reformed natural gases.

Jan 1, 1985

By R. M. Jimeson

Pressure-drop measurements through beds of granular iron, lathe turnings, steel wool, and parallel-plate assemblies were made at linear velocity and gas-density ranges expected in the Fischer-Tropsch hot gas recycle process.4/ Equations relating pressure drop, linear velocity, gas density, and bed porosity were derived. The results indicate that the exothermic heat of reaction can be removed at a lower cost by using catalyst beds with high porosity. INTRODUCTION The Fischer-Tropsch hot-gas-recycle process requires a catalyst offering low resistance to gas flow as one condition to economic feasibility. Conventional granular or spherical catalysts used during early development of the process in Germany did not meet this requirement. Large pressure drops across these beds made the cost of recirculating the gas excessive. The Federal Bureau of Mines is investigating the process by using novel and unusual catalysts that offer little resistance to gas flow. Pressure-drop measurements across these types of catalyst beds are discussed in this report.

Jan 1, 1959

By John J. Sammarco

Illumination plays a critical role in an underground miner?s safety because miners depend most heavily on visual cues to recognize hazards. Mobile mining machinery, located in the miner?s peripheral field-of-view (±10° to about ±60° off-axis), may pose potential pinning and striking hazards. The main objective of this research was to determine if there were peripheral visual performance improvements for the detection of moving objects when using cool-white light-emitting diode (LED) cap lamps as compared to incandescent (INC) light bulbs commonly used in miner cap lamps. The cap lamp variable of interest is the spectral power distribution (SPD); the illuminances were normalized by a diffusion filter. The second objective was to determine if age is a factor for peripheral visual performance. This is important because the workforce is aging ? the average miner age is about 43 years old. Thirty subjects participated in the study; ten subjects each in the age groups of younger (18 to 25 years), middle (40 to 50 years), and older (50+ years). Visual performance was quantified by the subjects? speed and accuracy of response to detect the rotation of high-contrast (white) circular targets located 3.83 meters (m) away at -20°, 40°, and 50° off-axis. The speed of detection and the number of missed target rotations (accuracy) were measured. The prototype LED cap lamp results were best with a 11% to 15% improvement compared to the INC and LED cap lamps respectively. Age does appear to be a significant factor. For the middle and older age groups?, target movement detection time increased 75% and 60% and the number of missed targets increased 500% and 450% respectively in comparison to the youngest age group. The results also suggest that target location is a significant factor. The subjects? target movement detection time for the 40° and 50° target movements increased 16% and 69% respectively as compared to the -20° target.

Jan 1, 2008

By Laxman S. Sundae

The Bureau of Mines designed, fabricated, and is using an in-seam tester (1ST) for in situ determination of coal cutting forces. This re-port describes the results of field tests conducted in the Pocahontas No. 3 and Upper Freeport seams to obtain peak and mean cutting forces during coal cutting with several bit geometries, including radial and point attack bits currently used on drum-type machines. Comparisons were also made between new and worn bits, and using data obtained from a Bureau-modified chisel bit. The test results show that longwall plough cutting (horizontal cuts) in bony coal bands (shale) requires >3 times the cutting force for the same cuts in a vertical direction. When no bony coal is present, the cutting forces required to make horizontal and vertical cuts are equal. Worn bits require 4 to 5 times more cutting and normal force than new or undamaged bits. Normal force increased drastically for the worn chisel bit. Peak force encountered in making independent cuts was found to be ~3 times higher than that required to make interactive cuts using a spacing-to-depth-of-cut ratio of 2. Both rake and clearance angles were found to have a significant effect on normal and cutting force.

Jan 1, 1986

By W. H. Tomlinson

Although the thoughts and efforts of the great majority of people in many parts of the world are today directed toward killing each other, the purpose of this paper is to discuss means of conserving human life. In a world of turmoil and strife, we find time to discuss and make plans to achieve our objective -prevention of the "sacrifice" of life through avoidable accidents. The word" sacrifice" is used here advisedly, as one meaning of the word given in the 1942 edition of Funk and Wagnalls New Dictionary of the English Language is "the act of giving up some desired or valued object for the sake of *** future good." As everyone agrees that life is man's most priceless possession, one wonders if past sacrifices have been in vain. It appears that life is cheap in America; it is cheap because some of the industrialists are too much concerned with making a profit to devote much time and thought to conserving human life; it is cheap because some labor leaders apparently are interested solely in personal power and prestige; it is cheap because a great many workmen fail or refuse to cooperate energetically with the various organizations interested ill; their safety and welfare; it is of little value because, individually and collectively, we are indifferent to our responsibilities toward our fellow men.

Jan 1, 1944

Objective: To devise a passive means to detect overheating insulators on mine trolley/track haulageways.

Aug 1, 1998

By E. E. Harton

Bureau of Mines Information Circular 7516, Bibliography of Investment and Operating Costs for Chemical and Petroleum Plants, was published in October 1949 to aid in estimating investment and operating costs of processes for manufacturing synthetic liquid fuels. Development of such processes by the Bureau of Mines was authorized by Public Law 290, 78th Congress. This bibliography included references to and abstracts of publications appearing from. 1930 to September 1948 on all processes in general use in the petroleum refining and chemical industries. Bureau of Mines Information Circular 7705, Supplemental Bibliography on Investment and Operating Costs for Chemical and Petroleum Plants, was prepared to cover the area from September 1948 through June 1952.

Jan 1, 1956

By M. L. Wang, S. R. Short, E. M. Daniloff, E. L. Petsonk, D. M. Mannino, G .. R. Wagner

"Background—It has been suggested that health related job selection is a major cause of the healthy worker effect, and may result in inaccurate estimates of health risks of exposures in the working environment. Improved understanding of self selection, including the role of airway hyperresponsiveness, should improve accuracy in estimating occupational risks.Methods—We evaluated symptoms of the respiratory tract, lung function, occupa¬tional and smoking histories, and airway responsiveness from a cross sectional sur¬vey of 478 underground bituminous coal miners and non-mining controls. Workers with abnormal spirometry were excluded from methacholine testing.Results—Methacholine responsiveness (= 15% decline in forced expiratory volume in one second) was associated in both miners and controls with reduced ventilatory lung function and an increased risk of respiratory symptoms. Miners with the longest duration of work at the coal face had a low prevalence of methacholine responsiveness, compared with miners who had never worked at the coal face (12% v 39%, P < 0.01). Throughout their mining careers, miners who responded to methacholine were consistently less likely to have worked in dusty jobs than miners who did not respond to methacholine.Conclusions—These results provide evidence that workers who are employed in dusty jobs are less likely than their unexposed coworkers to show increased non-specific airway responsiveness, pre-sumably as a result of health related job selection. Surveys of workers in which responsiveness data are unavailable may underestimate the effects of dust exposure on respiratory health."

Dec 1, 1996

By Thomas M. Barczak

This U.S. Bureau of Mines (USBM) report evaluates the load supporting characteristics of grout columns used as point supports for mine subsidence abatement. The cone-shaped columns were constructed with sodium silicate and cementitious grout in both wet and dry environments. The scope of work included the testing of seven full-scale grout columns in the USBM&apos;s Mine Roof Simulator from which the load-deformation and failure characteristics were determined. The performances of grout columns are analyzed with respect to (1) the amount of roof contact established during column construction, (2) shape effects produced by the truncated cone geometry, (3) size effects in reference to grout strength and full-scale column capacity, (4) the effect of wet environments on grout strength, (5) the effect of the sodium silicate on the grout strength and full-scale column behavior, and (6) the stiffness of the grout column. Limited tests were also conducted on cylindrical columns constructed in fabric bags. Recommendations for point support construction using sodium silicate technology and the need for additional research to develop improved containment devices for column construction are addressed in the report.

Jan 1, 2010

By P. E. Churchward

Rhenium sources and recovery methods were investigated by the Bureau of Mines to delineate potential resources of the metal. The only significant rhenium resource appears to be about 28,000 lb of rhenium contained in the domestic annual output of approximately 20,000 tons of byproduct molybdenite concentrates from porphyry copper operations. An estimated 70 to 80 pct of this rhenium is potentially recoverable by processing the rhenium-bearing fumes and dusts obtained during conventional roasting of molybdenite concentrate. At 70 pct recovery this would amount to 19,600 lb of rhenium. A more conservative estimate by the Committee on Refractory Metals of the National Research Council (1513 is that 12,000 lb of rhenium metal could be produced annually from current production of molybdenite from porphyry copper operations in the United States. A procedure was developed in the laboratory for recovering rhenium in the form of electrolytic flake by electrowinning the metal from a solvent extraction strip solution. The procedure included (1) water leaching of molybdenite roaster flue dust, (2) selective extraction of rhenium from the leach liquor by contacting it with a kerosine solution of a quaternary amine, (3) stripping of rhenium from the loaded organic solution by a perchloric acid solution, and (4) electrodeposition of rhenium from the loaded strip liquor. Raw material for the studies was flue dust containing 0.48 pct Re, 35 pct Mo, and 23 pct S in sulfide and sulfate form, and small amounts of numerous metallic impurities. Water leaching dissolved 85 pct of the Re and yielded a solution that was 13 in sulfuric acid and contained, 1 g/l Re and 16 g/l Mo. The solvent extraction strip solution that was electrolyzed for rhenium deposition was 1 molar in perchloric acid and 1 molar in ammonium sulfate and contained 13 g/l Re and 0.01 g/l Mo.

Jan 1, 1963

By R. Clark Lantz, Charles Stanley, David E. Hinton

Morphometric examination of lung alterations following exposure to toxic and pathogenic substances is invaluable in detecting subtle changes which might otherwise be overlooked. Results, from evaluation of initial structural alterations, support and guide subsequent nonmorphological techniques and, when coupled appropriately, can lead to a better understanding of the pathogenesis of a disease. Morphometry is a technique which can be used to determine, quantitatively, the site, extent, development, and progression of a disease state. Determination of the extent of tissue and cellular involvement in the response to inhalation of silica has been performed in order to gain a better understanding of the development of fibrosis following inhalation of this toxicant. In addition, since silica has been postulated as one of the important pathogenic minerals in coal mine dust' it is important to understand the lung tissue response to silica prior to evaluating the effects of inhaled coal mine dusts. Male Syrian golden hamsters were placed in Hazelton 1000 inhalation chambers and were exposed to either filtered air (controls, n = 24) or filtered air plus 30 mg!m3 silica (Min-U-Si110,95%ofparticles < 5 um,n =24)for16hours per day, five days per week, for two weeks. Animals were returned to the animal quarters prior to subsequent tissue processing at 1, 4, and 12 weeks following exposure. This schedule was designed to allow time for the development of fibrosis. Lungs were fixed by intratracheal perfusion of ½ strength Karnovsky's fixative at a pressure of 20 cm H20 and tissues were taken for embedment and analysis at the light level. Determination of site, extent, and development of alterations was performed using a multitiered approach. Changes in large structures (airways, blood vessels) was determined prior to evaluation of changes at the septal tissue level. Data will be presented outlining the progression of changes. Results indicate the usefulness of morphometric analysis of lungs following inhalation of toxic substances in quantitatively defining the structural alterations.

Mar 1, 1989

By Paul E. Bennett, James S. Browning, Thomas L. McVay

Continuous 1.0- to 1.5 - ton - per - hour pilot plant flotation tests were made to determine the technical and economic feasibility of recovering beryl from flotation tailing being produced at the spodumene concentrator of the Foote Mineral Company , Kings Mountain , N.C. Best results were obtained when using an acid circuit and amine - type cationic reagents to float a bulk beryl - feldspar concentrate and then selectively floating the beryl away from the feldspar , using a petroleum sulfonate collector . About 77 percent of the beryllium in the pilot plant feed was recovered in a concentrate containing 6.42 percent BeO . The capital cost of an integrated flotation plant capable of treating 500 dry tons of spodumene mill tailing per day for recovery of beryl and feldspar is estimated at $ 210,000 . Indicated direct operating costs for the plant were $ 1.52 per ton of dry spodumene flotation tailing treated . This approximated the value of beryl recovered , but potential profits of about the same magnitude lie in concurrent recovery of marketable spodumene and feldspar byproducts .

Jan 1, 1964

By R. Barany

The heats of formation of seven substances were determined by solution calorimetry. At 298.15° K, the heat of formation of lithium sulfate from lithium, rhombic sulfur, and oxygen was -343.1 ± 0.7 kcal/mole, and the heat of formation of lithium sulfate monohydrate from lithium, rhombic sulfur, oxy-gen, and hydrogen was -414.3 ± 0.7 kcal/mo1e. For the silicates, the heats of formation at 298.15° K from the elements were kaliophilite, -503.8 ± 0.5 kcal/mole; leucite, -721.6 ± 0,8 kcal/mole; eucryptite, -505,2 ± 0.6 kcal/mole; alpha-spodumene, -727.9 ± 0.9 kcal/mole; and beta-spodumene, -721.1 ± 0.9 kcal/mole. The corresponding heats of formation at 298.15° K from the constituent oxides were kaliophilite, -42.7 ± 1.1 kca1/mole; leucite, -42.8 ± 1.1 kcal/mole; eucryptite, -16.1 ± 0.7 kcal/mole; alpha-spodumene, -21.0 ± 0.7 kcal/mo1e; and beta-spodumene, -14.3 ± 0.7 kcal/mo1e.

Jan 1, 1966

By Charles T. Holland

ANALYSIS of 117 occurrences of bumps in coal mines shows that 67.6 percent are associated with pillar-line points.4 Slabbing and splitting pillars, development, and other unfavorable milling practices in abutment areas may be a contributory or the primary cause of bumps. The cure for pillar-line bumps is to recognize areas that can be expected to become highly stressed and to project the mining plan and operations to eliminate such areas insofar as possible. If such areas cannot be eliminated, then the mining plan and operations should be projected to avoid the necessity of disturbing these areas before the stresses have been dissipated.

Jan 1, 1954

By A. E. Raddatz

Previous Bureau of Mines research has shown that tungsten ores containing as little as 40 pct W032-can be processed by a high-temperature molten-salt extraction technique to produce a tungstate-bearing sodium chloride phase with 99 pct W recovery and little impurity contamination. The objective of this work was to demonstrate that the tungstate-bearing sodium chloride phase can be a suitable feed material for preparing am-monium paratungstate (APT) by a modification to the present industrial solvent extraction process. A combined crossflow-count·ercurrent flow solvent extraction technique to extract tungsten is presented. APT produced by this new technique contained 88.6 pct W032-and the following impurities, in percent: Mn02_ 0.0007, Mo02 0.017, P205 <0.010, and Si02 0.012. Implementation of this processing technique would improve tungsten recovery from concentrates and simplify processing operations.

Jan 1, 1988

By W. H. Oppelt

Two exploratory gasification tests of limited duration were made at Dorsten, Germany, with strongly coking Pittsburgh-bed coal in a fixed-bed pressure gasifier. To reduce the coking potential of the Arkwright coal, ash refuse from the gasification of Dorsten (Leopold) coal was added to pre-pare coal-ash mixtures which contained nominal 20 and 30 percent ash. Major adjustments in principal process variables at the beginning of the tests resulted in wide fluctuations in the rate of gas production, gas offtake temperature, and carbon dioxide concentration in the gas. Because a higher steam-to-oxygen ratio was used in the tests than was customarily employed for routine operation, gas production was lower, and steam and oxygen consumption was higher. After operating conditions had been improved, the results of a 12~-hour-long test with addition of sufficient ash refuse to obtain a nominal 30 percent ash concentration indicated that operation is feasible with this coal mixture using a fixed-bed pressure gasifier equipped with a rotating coal distributor and stirrer.

Jan 1, 1966

By J. Douglas Causey

In 1984, at the request of the Bureau of Land Management, the Bureau of Mines studied 29,020 acres of the 43,165-acre Terry Badlands Wilderness Study Area (MT-024-684) in order to evaluate its mineral resources. Within this report, these 29,020 acres are referred to as the study area. Located in Custer and Prairie Counties, MT, the study area is about 2 miles northwest of Terry. The study area is underlain by essentially flat-lying units of the Fort Union Formation of Paleocene age with some Quaternary alluvial deposits in stream valleys. No mines or prospects were found in the study area. Bentonitic clays and lignite coal units were examined and sampled; however, no clay resources or coal reserves were identified. Estimates of coal resources will be reported by the U.S. Geological Survey in a joint U.S. Geological Survey-U.S. Bureau of Mines publication. Gravel along the Yellowstone River, a source of agate for private collectors, could also be used as sand and gravel aggregate although material on the south bank of the river is closer to population centers and road systems. Clinker found in the study area could be a source of road metal, but is not well situated in relationship to areas of use. No geothermal resources have been identified although water suitable for direct heat applications may underlie the study area. All the area is leased for oil and gas exploration.

Jan 1, 1985

By Frank E. Cash

Data on the occident experience of the pebble-phosphate industry in Florida for 1937 and 1938 are combined in this report with statistics for the 7-year period 1930-36, inclusive, which were published in Information Circulars 69174/ and 69685/. The periodic publication of such data enables the pebble-phosphate industry, as well as other industries, to consider relative hazards, compare experience, and thereby help to prevent accidents. ACKNOWLEDGMENTS Accident data ere furnished by the following; operating companies: Amalgamated Phosphate Co., Brewster; American Agricultural Chemical Co., Pierce; Coronet Phosphate Co., Plant City; International Agricultural Corporation, Mulberry; Phosphate Mining Co., Nichols; Southern Phosphate Corporation, Bartow; and Swift & Co. Fertilizer Works, Bartow.

Jan 1, 1940