Search Documents

By H. F. Yancey

The Baum-type jig used so widely to clean bituminous coals has not been adopted for anthracite. If proved suitable for anthracite, its use might lower preparation costs in some plants. Cleaning trials on a Pennsylvania anthracite in a laboratory-size Baum-type jig were undertaken by the Bureau of Mines to provide indicative information that would be helpful in determining whether the cost of a full-scale installation would be justified. Clean coal surpassing standard anthracite specifications was obtained in all sizes from Stove through No. 5 Buckwheat. Recovery effi¬ciencies were acceptable down to 3/16-inch size, but there was excessive loss of coal in the finer sizes. Thus the fine refuse produced in a commercial plant might re¬quire retreatment. A comparative cleaning trial in a dense-medium pilot plant provided a recovery efficiency only l percent higher than obtained in jigging.

Jan 1, 1957

Develop a means of determining both the fill level of material in an ore pass or bin and the location of bridging material causing a blockage.

Jan 1, 2000

By Martin Hertzberg

The early and reliable detection of the self-heating of combustible substances in mines is of considerable importance to the mining community. This Bureau of Mines report describes the results of a variety of studies of incipient combustion and its detection. Heated samples of coal, wood, and various polymers were used to evaluate the relative sensitivities of several types of detectors. The laboratory results indicate that submicrometer particulate detection is the most universal and sensitive method. Carbon monoxide detection was as sensitive as submicrometer particulate detection for pyrolyzing coal but was relatively insensitive to pyrolyzing wood or plastics. The conventional type of ionization smoke detector was the least sensitive for coal and of intermediate sensitivity for wood and plastics. Self-heating experiments with Pittsburgh seam coal piles of varying particle sizes gave ignition temperatures of 170° C for 4-to 7-µm dust, which increased monotonically with particle size. The measured heating rates were compared with data from an adiabatic calorimeter to obtain preexponential rate constants. The preexponential rate constants varied linearly with the surface area per unit mass of sample as would be expected for heterogeneous surface oxidation. The propagation behavior of ignition waves and the overall self-heating appears to depend critically on the magnitude of the convective flows induced, which counteract the depletion of oxygen in the void spaces of the pile. Classical theories of thermal ignition require substantial modification to be applied reliably to such cases.

Jan 1, 1977

By Larman J. Heath

Liquid incendiaries were burned within the interstices of several different types of sandstone cores to determine the technical feasibility of increasing sandstone permeability by this method. Fuel-oxidant mixtures were tested in 186 cores; six cores exploded when ignited. In virtually all instances, the explosion completely pulverized the sandstone cores. In addition n those cores damaged by explosions, 24 cores were fractured so severely that permeability tests were impossible. Although combustion gener¬ally increased the permeability, specific mixtures at given pressures were inconsistent in their ignition and burning behavior. Tests indicated that the heat of burning incendiaries significantly increased sandstone permeability. The improved permeability ratios were usually less than 2, but one was 10.3. Permeability alteration by other in situ methods was not as effective as that by flame propagation.

Jan 1, 1971

By M. R. Yenchek

The Bureau of Mines conducted research to determine the relationship between cur-rent load and temperature rises in coal mine trailing cables. Six low-voltage, unshielded, portable power cables were continuously and intermittently loaded with direct current of various magnitudes. Temperature rises within and on the cables were measured with thermocouples, and the data were recorded with a computer. Thermal time constants were calculated, which fixed the periods of the duty-cycle tests. Relationships between average temperature at the conductor-insulation interface and current load were established. The steady-state and intermittent currents that produce a 90° C average conductor-insulation temperature were then determined. Comparisons with Insulated Cable Engineers Association (ICE A) steady-state ratings revealed that 10 to 25 pct more current than recommended ICEA ampacities is required to reach rated insulation temperature. Examination of the maximum intermittent temperatures attained showed that autoignition of coal dust and burn injuries to personnel handling the cable would not be concerns if the temperature at the conductor-insulation interface averaged 90° C.

Jan 1, 1988

By A. B. Needham

This paper, which describes mining practices at a mine in the Cave- in-Rock, Illinois, fluorspar district, is one of a series being prepared by the Bureau of Mines on mining practices, methods, and costs in the various mining districts of the United States. Ore deposits in the southern Illinois-western Kentucky fluorspar dis- trict are of two general types (1) the flat-bedded, lenticular replacement and (2) the relatively narrow, rather steeply dipping fault or fissure filling. This paper describes production methods used and results obtained in mining one of the bedded lenticular ore bodies that are prevalent in the northeast portion of the district near Cave-in-Rock.

Aug 1, 1949

By Joseph W. Martin

The Bureau of Mines investigated the backscattering of low-energy gamma rays as a method for rapidly determining the incombustible content of coal mine dust. In this method, 60-kev gamma rays from americium-24l penetrate the dust and are reflected by elements in the dust to a thin crystal scintillation detector. The number of backscattered gamma rays is proportional to the incombustible content. Tests of 40 dry, mine-dust samples containing 50 to 100 percent inert material show an average error of 2 percent. Calibration of the apparatus is necessary for each rock dust to account for variable composition. Results for samples containing more than 6 percent moisture are subject to error, but the values are lower than values obtained by chemical analysis, and thus fall on the safe side. Development of a small portable meter based on the backscatter principle appears feasible. Such a meter would find application within coal mines to check the effectiveness of rock dusting procedures.

Jan 1, 1968

By A. L. Murray, C. A. Allen

"The Industrial Commission of Utah from a study of the accidents (especially the fatalities) occurring in connection with mining in the State was struck by the large number arising from lack of due care on the part of the employee injured or carelessness on the part of some fellow employee. Figures show that approximately 40% of the deaths are due to carelessness as against only ) 10% or 12% that can be laid to faulty conditions in the mines. With a view to reducing the number of these accidents an intensive campaign of education was inaugurated, conducted jointly by the Industrial Commission of Utah and the United States Bureau of Mines.Through the cooperation of the U. S. Bureau of Mines, Mine Rescue Car No. 11 operating in Utah has been utilized as the means of carrying on the campaign. In making the regular training visits to the mining camps of Utah the crew of car 11 was authorized to include with the courses of instruction in Mine Rescue and First Aid, safety and health rallies, foremen's safety meetings, and appeals carried on through the public schools to stimulate an awaking of personal responsibility of miners and their familiar' in safety and health endeavor. The work was placed under the direct charge of Dr. Murray who has had previous experience in similar work and brought to the campaign helpful enthusiasm. He was assisted by Bruce Johnson, fore¬man miner of Car 11, who had been safety engineer for the U. S. Smelting Company, and R. W. Clark, first aid miner of Car 11. The expense of providing posters, literature, pledge cars, buttons, rental of special educational films and incidental expenses of foremens' meetings has been born by the Industrial Commission.Plan of the Campaign.In planning the campaign the main object was to revive as much as possible, among the workers, a spirit of responsibility for safety. Any considerable reduction of preventable accidents can be accomplished only through the workers themselves who are responsible for such accidents, therefore, the more personal the application could be made to all the workers the greater the accruing results would be."

May 1, 1921

By T. A. Henrie, J. D. Marchant, E. S. Shedd

Cerium metal was electrowon in a fluoride bath from cerous oxide and tapped from the cell during prolonged operation . Electrolyte constituents were CeF , BaF₂ , and LiF. Twenty- seven pounds of metal of 99.8 percent purity were produced at a rate of 3 pounds per hour and tapped from the cell . Principal impurities were molybdenum , aluminum , oxygen , and carbon . The operating parameters , such as electrode geometry , bath compositions , and oxide feed rate , were investigated . Anode reactions were found to be important factors in cell operation . Stable cerous oxide reacted more uniformly at the anode surface than ceric oxide . Electrowinning was conducted in crucible hearths consisting of both frozen electrolyte and molybdenum metal . Both materials proved satisfactory and did not react with the molten cerium . Stable cerous oxide was prepared by carbothermic reduction and used as a feed material . Cell design proved to be an important factor in continuous cell operation . Complementary to the investigations of electrowinning of cerium , the metal was purified by electrorefining in a chloride electrolyte .

Jan 1, 1964

By T. E. Gray

This report describes the preparation characteristics of the significant coalbeds in Harrison County, W. Va. It is one in a series of Federal Bureau of Mines reports planned to determine coals suitable for the production of metallurgical coke, either as mined or after beneficiation. Over 6.5 million tons of coal was produced in Harrison County, W. Va., in 1958, of which over 3.7 million tons was cleaned mechanically in seven preparation plants. All of the coal cleaned was from the Pittsburgh bed. It has been estimated that more than 1,816 million tons of coal remains in the county in beds 12 inches or more thick. The Pittsburgh and Redstone beds were selected by the Bureau for a study based on current production rates and estimated minable reserves. Sample locations were selected following a study of the literature, conferences with mining engineers and mining company officials in the field, and examination of the available sites. Six samples were collected from the Pittsburgh bed, and three samples came from the Redstone bed, Float-and-sink tests of the samples collected from the Pittsburgh and Redstone beds showed that neither coal could be upgraded to a metallurgical fuel under the standards set up for this study, even after intensive preparation. Finer crushing of the samples moderately increased the yields and slightly reduced both the ash and the sulfur contents in the 1.30-specific-gravity float fractions. Finer crushing slightly decreased the yields in the 1.58-specific-gravity float fractions, whereas it reduced the sulfur content 0.11 percent for the Redstone sample and 0.46 for the Pittsburgh sample.

Jan 1, 1961

By Mark R. Pettitt

The results of an extensive research and development program to reduce the noise generated during coal cutting are presented. The characteristics and magnitude of continuous miner coal cutting noise sources are defined. This work consisted of development of a simulated coal ,cam to facilitate above-ground coal cutting tests, noise measurements in a reverberant acoustic chamber during simulated mining operations of a continuous miner (cutting the simulated coal scam), and noise measurements in an underground coal mine during continuous miner operation. In-mine and laboratory test results were in excellent agreement for both A-weighted overall levels as well as A-weighted one-third octave band spectra. Methods to reduce coal cutting noise are presented. These methods take full advantage of the dynamic characteristics of the forces generated during coal cutting. Dynamic cutting force isolation was shown to be a very effective technique. Finally, a continuous miner was equipped with a cutter head that incorporated (among other design factors) cutting force isolation. Successful, lung term, in-mine use of the cutter head demonstrated coal cutting noise at the operator's station of less than 90 dBA and 50% coal, 50% rock cutting of less than 93 dBA.

Jan 1, 1985

By W. H. Emens

[This circular is one of a series dealing with tie development and equip¬ment of small and medium size mines, and with the costs of such work prior to productive operation. The preparation and publication of these papers by the Bureau off Mines has been made possible through the cooperation of various min¬ing and development companies. The bureau of Mines has published a series of circulars dealing with min¬ing methods and costs at a large number of producing nines in the United States, Canada, Mexico, an, other countries. Unit costs of development work, shaft sinking, (rifting, crosscutting, tunneling, and raising are usually much higher in the preliminary development of a property than during its productive life.]

Jan 1, 1933

By R. H. Reist, R. D. Dey, V. Castranova, J. P. Durham, Y. Rojanasakul

"Silicosis is a fibrotic pulmonary disease produced by inhalation of silica-containing dusts (Peters, 1986). Chronic silicosis may develop 20-40 years after initial exposure to crystalline silica, and the disease may progress from a simple to a complicated form. Few symptoms are evident in simple silicosis with pulmonary function being relatively normal. However, chest radiographs reveal small rounded ·opacities in the upper lobes of the lungs. These silicotic nodules consist of collagen arranged in a distinctive circular pattern. As fibrotic changes become more severe, the disease progresses to complicated silicosis (progressive massive fibrosis). Complicated silicosis is associated with shortness of breath and decreases in pulmonary function characteristic ofrestrictive lung disease. Chest x rays reveal numerous large silicotic nodules which may be associated with scar emphysema. Several mechanisms have been proposed to explain the cellular events which result in silica-induced lung damage and fibrosis (Lapp and Castranova, 1993). They include: ( l) direct cytotoxicity of silica, (2) activation of oxidant and enzyme release from alveolar macrophages, (3) recruitment and activation of polymorphonuclear leukocytes, and (4) stimulation of fibroblast proliferation and collagen synthesis.Tetrandrine is a bisbenzylisoquinoline alkaloid derived from the Chinese herb Radix Stephania tetrandra. It has a molecular weight of 622.73 and an empirical formula of C38H420 6N2. The chemical structure of tetrandrine has been published previously by our laboratory (Castranova et al., 1991 a). Its structure is characterized by methoxy groups at C7 and C12 , uncharged nitrogens at N2 and N’2 and two 17-carbon ring members connected by a double oxygen bridge between Ca-C7 and C11-C12. Tetrandrine has been shown to reduce both silica-induced fibrosis and the elevation of lung collagen content in rats (Huang et al .. 1981; Yu et al., 1983; ldel, 1987). Furthermore, tetrandrine has been used as an antifibrotic agent in Chinese clinical trials (Li et al.. 1981 ). Preliminary results suggest that administration of tetrandrine to patients with silicosis results in substantial improvement of symptoms, increases in diffusion capacity, and decreases in the size of shadows on lung x rays."

Nov 1, 1995

By R. K. Koch

The Bureau of Mines produced several series of titanium castings in order to investigate the feasibility of producing commercial-grade titanium castings in bentonite-bonded olivine or zircon sand molds. The use of these molds for titanium casting was investigated as a possible alternative to the industrially used rammed graphite process. Parameters investigated were mold mixtures, mulling, gating, venting, drying, and mold washing. The investigators found that castings with superior ductility and fatigue life, compared with rammed graphite castings, could be made by fume-free pro-cesses in molds bonded by western bentonite, using either olivine or zircon sand. Zircon molds were satisfactory for both light-and heavy-sectioned castings. However, olivine molds were suitable only for light-sectioned castings because the mold-metal reaction became excessive during the pouring of heavy-sectioned castings.

Jan 1, 1981

By Robert E. Wallhagen

The froth foam seal topping system is part of a system for remote sealing of mine passages using flyash transported pnuematically from the surface. Making the final 5 percent of the seal with a foamed-in-place fire retardant polyurethane reduces the required flyash volume by 50 percent and provides a more reliable seal. Foam components are held at the surface under proper conditions of temperature and pressure; then conveyed down the borehole through individual hoses and mixed at the bottom with a static mixer. The polyol component is pre-mixed with fluorocarbon-12 which, when released from system pressure in the mixer, boils and causes the foam to expand. Difficulties in handling this particular foam formulation are offset by a flame spread index well below the 25 level by ASTM E-162 normally required for under-ground applications. Isocyanate, polyol (TDI) and catalyst are conveyed to the downhole package by three separate lines. Five additional lines operate the valving and convey solvent so that the mixer and package lines can be flushed immediately after foaming. The eight-hose bundle is provided in segments of several lengths so that bore-hole depths can be matched. Cast-in-place plastic cylinders hold the bundle together and transfer the weight of the hose through a special quick-release clamp to the crane's wire rope. The downhole package and hose bundle are deployed using a specially designed winch and crane system capable of borehole deployment to 1500 feet.

Jan 1, 1977

By Bernard J. Steblay

Two instruments have been constructed that extend microseismic data collection and processing capability for Bureau of Mines research in rock burst, coal bounce and outburst, and roof fall monitoring. The first instrument is a 13-channel tape-triggering system. This system allows better utilization of instrumentation tape recorders by collecting data digitally, turning the tape on only when valid data are present, and increasing the dynamic range of the recorder by using digital data. A digital-to-analog converter is used to provide analog output of the recorded digital data. The instrument records a much larger time slice of transient events than do current commercial devices. The second instrument is a microseismic energy measurement device. This device uses recent developments In integrated circuits to overcome the dynamic range and accuracy limitations of previous instruments. The analog signal is converted to a digital one, and then high-speed multiplication techniques are used to square the amplitude value in real time and integrate it.

Jan 1, 1983

By Oliver Bowles

Limestone is the most widely used of all racks and is essential to a great many industries, including tae building trades, highway construction, metallurgy, agriculture, end many chemical and manufacturing enterprises. It occurs in some form in every State and is produced in thousands of quarries. Production in 1930 exceeded 134,000,000 tons. It has more numerous and more diversified uses than any other rock. This paper is designed to furnish general information on the various branches of limestone quarrying and their economic importance. Brief reference is made to dimension stone, and a more complete discussion follows of the uses, requisite qualities, quarry methods, grid processes of preparation of crushed and broken limestone. Footnote references serve to guide the reader to more detailed information.

Jan 1, 1933

By Arthur L. Miller

Recent studies suggest that trace metals emitted by internal combustion engines are derived mainly from combustion of lubrication oil. This hypothesis was examined by investigation of the formation of particulate matter emitted from an internal combustion engine in the absence of fuel-derived soot. Emissions from a modified CAT 3304 diesel engine fueled with hydrogen gas were characterized. The role of organic carbon and metals from lubrication oil on particle formation was investigated under selected engine conditions. The engine produced exhaust aerosol with log normal-size distributions and particle concentrations between 105 and 101 cm-3 with geometric mean diameters from 18 to 31 nm. The particles contained organic carbon, little or no elemental carbon, and a much larger percentage of metals than particles from diesel engines. The maximum total carbon emission rate was estimated at 1.08 g h-1, which is much lower than the emission rate of the original diesel engine. There was also evidence that less volatile elements, such as iron, self-nucleated to form nanoparticles, some of which survive the coagulation process.

Jan 1, 2007

By W. S. Landers

This bulletin is a detailed study of low-temperature, entrained-bed carbonization of a Texas lignite. The lignite studied was from the Sandow strip mine and is representative of the Rockdale formation of the Wilcox formational group. Carbonization was conducted in a continuous entrained-bed reactor at several temperatures in the 8801 to 1,52°C F range, and at air-coal ratios it the 0 to 10.30 scf/lb range (moisture- and ash-free basis). Carbonization rates ranged from 97.1 to 410.0 lb/hr (as-received basis), At the higher air-to-coal ratios employed, all or most of the carbonization heat was provided by internal combustion with air in the reactor. At the lower air-to-coal ratios, parts of the heat for carbonization was supplied externally. It was demonstrated that the entrained-bed carbonization of lignite is a complex reaction and that several variables, of which carbonization temperature, air-to-lignite ratio, and the average size of lignite are important, act together to influence both the carbonization yields and the properties of the resultant products, Process variables established by pant tests were used to design the industrial scale carbonizer operated at Rockdale, Texas, by the Texas Power & Light Company as agents for the Aluminum Company of America. Properties of the carbonization product obtained from the industrial scale reactor were essentially the same as those obtained from the pilot plant reactor operated under the same conditions.

Jan 1, 1968

By J. O. Winget

Phosphonic acid and iminodiacetic acid chelating resins were investigated to assess their potential as selective ion exchangers for separating lanthanide elements and yttrium . The affinity of phosphonic acid resin for lanthanides increases with increasing atomic number , and that of iminodiacetic acid resin for lanthanides increases with atomic number to a maximum for element 62 and then declines with atomic number throughout the remainder of the series . Elution sequences of the elements with mineral acid eluants corresponded favorably with equilibrium data , whereas the elution sequence obtained with chelating eluants was proportional to the relative values of the stability constants of the chelating agents with the lanthanides . Separation of lanthanide mixtures into groups of light and heavy elements with iminodiacetic acid resin appears feasible .

Jan 1, 1964