Search Documents

By C. H. Riggs

This report describes the development, oil recovery, and potentialities of productive formations in the Hall-Gurney field, Russell County, Kans. It is presented as part of a general program to aid and promote increased recovery from petroleum reservoirs. The report is based on studies of well logs, drill cuttings, and oil-and water-production histories of individual wells and leases. The geological interpretations follow closely those in published literature with only slight local modifications. Oil and water analyses, made at a Bureau of Mines research center, were supplemented by many analyses obtained from oil-producing and service companies. The Hall-Gurney field, in south central Russell County, Kans., (fig. 1) was discovered in 1931 but was not developed extensively until 1941. By 1960 the rate of oil production from the field had declined to the extent that many wells were abandoned. In some areas natural productive forces have effected good recovery. However, in other areas inefficient waterflooding, both natural and accidental, has adversely affected recovery potentialities.

Jan 1, 1963

By Glenn A. Shirey

The objective of this contract as to prepare a detailed, readily usable handbook on dust control techniques for longwall mining operations. Information was gathered from available literature, and through contacts with industry and government personnel. The handbook describes those methods of dust control applicable to today's longwall mining systems, and contains sufficient design elements to assist operators with problems in testing or implementing new control procedures. Complete reference lists are presented at the end of each chapter to direct the reader to additional information.

Jan 1, 1985

By J. M. Singer

This study was undertaken to obtain some fundamental information about hazardous mixtures of coal dust and methane (firedamp) likely to occur in mines. Fuel concentration limits for ignition of mixtures of coal dust, methane, and air have been determined by a hot-gas ignition method. The limiting concentration of each of the two fuels was usually less than that corresponding to its lean flammability limit in air. The lean limits of flammability of coal dust vary with the type and size of the dust; in this study coal dust concentrations were less than 80 mg/liter. Ignition jets were turbulent pulses (emerging from a channel of 0.5 cm diam) resulting from explosions of stoichiometric mixtures of methane, oxygen, and nitrogen, Temperatures of the ignition jets were varied by changing the oxygen index (OI) = O2/(02 + Nj2) of the primary methane-oxygen-nitrogen mixture (adiabatic flame temperatures from 2,000° to 3,000° K). The objectives of the study were to establish quantitative relations between concentrations of each fuel at ignition limits of hybrid mixtures and to study the mechanism of ignition of these hybrid mixtures by hot turbulent gases, Empirical equations were fitted to concentrations for four coals, namely) Pittsburgh Seam (sizes A, B, and C), Sewell No.2 Seam, pocahontas No.3 Seam, and anthracite. Equivalences of coal dust to methane were computed from these equations; equivalence being defined as -Ac/Am, where c is the coal dust concentration and m is the methane concentration, each in milligrams per liter of air. It was found that the equivalence increases as the temperature of the hot-gas jet decreases. In general, the equivalence is also an inverse function of volatile content of the coal and a direct function of the particle size, However, volatile con-tent in itself is not a sufficient correlating variable, nor is the specific surface area of the coal dust.

Jan 1, 1967

By Richard N. Spencer

Electric-furnace smelting for simultaneous recovery of zinc spelter and lead bullion from complex lead-zinc sinter was investigated. Reduction of lead and zinc was satisfactory. Condensation of lead and zinc vapor to pyrophoric metal powder in a water-cooled, shock-condensing system produced excellent recoveries. Metal-splash condensation to produce zinc spelter was unsatisfactory. Special smelting experiments differentiated the effects of several smelting parameters on zinc metal recovery. The principal cause for unsatisfactory zinc metal recovery was transfer of iron to the condenser and subsequent degradation of zinc in a mixture composed of lead and an iron-zinc intermetallic compound. Limitations of the process were determined. Slag-resistance open-bath electric smelting of complex lead-zinc sinter is not considered feasible.

Jan 1, 1967

By M. M. Tilman

The Bureau of Mines evaluated corrosion resistance of Split Set friction rock stabilizer mine roof bolts to aid in better prediction of useful service life. Electrochemical corrosion testing was conducted utilizing an automated corrosion measurement system. Natural and/or synthetic mine waters from four uranium and two copper mines were the test media for the two types of high-strength, low-alloy (HSLA) steels from which Split Set stabilizers are manufactured, and for galvanized steel. Tests were conducted with waters of minimum and maximum dissolved oxygen content at in-mine water temperatures. Retrieved Split Set stabilizers were also evaluated for property changes. Galvanized steel was found to be far superior to the unprotected steel in general corrosion resistance; limited tests indicate little ten.dency to pitting, contrary to behavior for the uncoated steel. Copper-bearing HSLA steel was slightly more corrosion resistant than non-copper-bearing HSLA steel. Statistical analyses resulted in development of equations relating dissolved oxygen, chloride, sulfate, and magnesium contents of mine waters to corrosion rates of the two HSLA steels (nongalvanized). An equation was developed that relates corrosion rates of galvanized steel to mine water temperature and dissolved oxygen content. Variable conditions in mine environments make corrosion damage difficult to predict and emphasize the need for corrosion prevention and control.

Jan 1, 1984

By Fredrick L. Johnson

In 1984, at the request of the U.S. Forest Service, the U.5, Bureau of Mines began a study of the 94,370-acre Arc Dome study area (4-667) in order to appraise its mineral resources, The Bureau of Mines mapped and sampled mines, prospects, and mineralized sites in and near the area, The study area is located in the Toiyabe National Forest, about 54 mi north of Tonopah, Nye County, NV, It is estimated that over 500 claims have been staked in the study area since the mid-1800?s. In January 1986, there were 108 active mining claims completely inside and 59 on the boundary. Another 283 active claims were outside the study area but within 1 mi of the boundary, In addition to the large number of claims staked, exploration activity is also reflected by the almost 700 inactive workings that were found during field investigation.

Jan 1, 1989

[~lis is the f'fth in a ~erieG of reports on properties of commercial motor fuels, made in accordance 1,'Vi t:h fl cooperative ae,ree-ment betwGon tho Cooperative Fuel ReRRarch (e.F.R.) Committee and the Bureau of I ines of the Dcpart~ent nf the Interior. The first report gave data on motor r-asolino~ sold during the wintor of 935-36.31 Thi~ report covers 84 brands of ga~oline represented by l,722 samples exclurling the Pacific Coast. T 3)Se J.rom th~. ?~'tcific Coast IV .ro avnrL)f:od b~r tho Pacific Coa!3t tecilnical group "bofore o8ing submi ttcd ruld arc p~.lbl:'shcd GX Gtl~r as they were submi tted. In some areas r~lJort~ . erc roceivod f~om ~ ix to eicht compD.l1ie~ on the same brands of gasoline. whoruar. in other areas only one company reported on a brond. Thut., it CU .. "! be senn that BO .. 0 uf the dnt ;.U'e more rCY>l'c entat vc thM others. The inclusion of r~0rts fro:n several ci tie. w' thin somo of tho di stricts has ir.rpr,)vcd the report by reducinc; tr.e numb~r of brand rcportel by only ono company. ]

Jan 1, 1938

[~lis is the f'fth in a ~erieG of reports on properties of commercial motor fuels, made in accordance 1,'Vi t:h fl cooperative ae,ree-ment betwGon tho Cooperative Fuel ReRRarch (e.F.R.) Committee and the Bureau of I ines of the Dcpart~ent nf the Interior. The first report gave data on motor r-asolino~ sold during the wintor of 935-36.31 Thi~ report covers 84 brands of ga~oline represented by l,722 samples exclurling the Pacific Coast. T 3)Se J.rom th~. ?~'tcific Coast IV .ro avnrL)f:od b~r tho Pacific Coa!3t tecilnical group "bofore o8ing submi ttcd ruld arc p~.lbl:'shcd GX Gtl~r as they were submi tted. In some areas r~lJort~ . erc roceivod f~om ~ ix to eicht compD.l1ie~ on the same brands of gasoline. whoruar. in other areas only one company reported on a brond. Thut., it CU .. "! be senn that BO .. 0 uf the dnt ;.U'e more rCY>l'c entat vc thM others. The inclusion of r~0rts fro:n several ci tie. w' thin somo of tho di stricts has ir.rpr,)vcd the report by reducinc; tr.e numb~r of brand rcportel by only ono company.]

Jan 1, 1938

By William W. Adams

The stone-quarrying industry of the United States, including such related operations as rock crushing, rock dressing, and the manufacture of cement and lime, reported a larger volume of employment in 1934 than in 1933. Reports from the operating companies to the United States Bureau of Mines showed an increase in the number of men employed, number of man-days of employment, and total number of man-hours of labor performed during the year. Moreover, the average worker had a longer period of employment during 1934, the gain amounting to 11 percent over 1933. The increase in employment was accompanied by no increase in accidents for the industry as a whole; in fact, the accident rate for 1934 was a fraction lower than the rate for 1933. In some branches of the industry the frequency of accidents increased, but these increases were more than offset by reductions in rates for other branches. Reports for 1934 were received from 1,403 active plants. The working force averaged 64,331 men for 204 days per man, and the total period of employment for all of the men was 95,258,880 man-hours. Each employee averaged 1,481 hours of work during the year. The total number of hours of labor represented a gain of more than 8 percent, and the average working time per employee showed a gain of 62 hours per man.

Jan 1, 1936

By P. B. Altringer

Searles Lake, CA, contains the largest known domestic tungsten resource. The brines in this near-dry lake bed, located in the Mojave Desert 130 mi northeast of Los Angeles, contain an estimated 135 MMlb of tungsten. However, the low concentration of tungsten (0.080 g/L W03) in the supersaturated brine makes selective tungsten extraction very difficult. Although many brine chemicals are extracted from the lake, tungsten recovery was an elusive goal prior to Bureau of Mines development of an ion-exchange technique. This publication describes the Bureau process. The following subjects are ad-dressed: ? The Searles Lake tungsten resource. ? General problems associated with tungsten recovery. ? Bureau research objectives. ? Synthesis of ion-exchange resins. ? Development of a two-stage ion-exchange tungsten extraction and concentration procedure. ? Product recovery and purification. ? Economic evaluation. Flowsheets for recovering three products (calcium tungstate, sodium tungstate, and tungstic oxide) are presented and evaluated, as well as a summary of the research effort and potential applications.

Jan 1, 1985

By Benjamin W. Haynes

This Bureau of Mines publication comprises a compilation of the state of the science in Pacific Ocean manganese nodule mineralogy and elermental composition. The report is divided into three sections: morphology, mineralogy and elemental composition. The nodule morphology section defines what is considered a nodule for the study, and details the external characteristics and internal structure. Nodule mineralogy is discussed in three sections: manganese minerals, iron oxide minerals, and accessory minerals. The major manganese minerals discussed are todorokite, birnessite, and vernadite. The iron oxide minerals are less well known and include feroxyhyte, goethite, and lepidocrocite. Accessory minerals present include quartz, clays, and other silicates and nonsilicates. A discussion on moisture content is also included. The elemental composition section presents data on 74 elements occurring as cations or anions. Summary data, histograms, and interelement correlation coefficients are presented. The elements are grouped as follows: major and minor elements of potential economic interest (8), other major and minor elements (9), elements of environmental interest (8), rare-earth elements (15), precious-metal-group elements (6), radioactive elements (3), other trace elements (17), and anion-forming elements (8). Cross sectional determinations of Ni, Cu, Zn, Co, Pb, Fe, Ce, and Ba are given for a single nodule to show the general tendency of different growth patterns within a nodule because of different element associations and composition.

Jan 1, 1982

By Arnold O. Tanner

The domestic mining industry continued to be strengthened and revitalized in 1989. The healthy conditions and the industry comeback that began in 1987 continued to spread and became more established for many commodities. Relatively comfortable and stable commodity prices, still found predominantly in the metals sector, reinforced other operational factors in bringing vitality to the mining and mineral processing industries. New streamlined business practices, mine and plant modernizations, and the progressive use of new technologies successfully helped lower operating costs and increase efficiency during the past 5 to 7 years. An element common to these three factors of industry renewal and growth was the ever-increasing infusion of and growing dependence on constantly advancing computer technology applications. This trend of increasing computerization was occurring throughout the mining and mineral processing business while it similarly was in most facets of modern business and culture. Some commodities and companies still struggled to outlive sluggish prices and other unstable market conditions or to modernize their businesses, but increases in productivity and profits were more common. A trend toward increased mechanical excavation in nonsoil materials was beginning to surface as a substitute for standard cyclic mine development techniques, such as drill-and-blast and surface shovel-and-truck routines. More continuous mechanical excavation offered the potential for increased production, fewer people at the working face, better ground control, and generally improved safety. The main limitation was rock hardness. The construction industry had already recognized the benefits of tunnel-boring machines for long underground drives and mechanical planers for pavement removal. The Colorado School of Mines held a short course during the year entitled, "Mechanical Excavation Techniques in Mine Development and Production,'" which was at-tended by nearly 100 engineers from 12 countries. The consensus of attendees was that for the most efficient use of these machines and techniques, new mining plans needed to be developed beyond the simple adaptation of those excavators to existing mine plans.1

Jan 1, 1991

By Bernard Lewis

This report summarizes fundamental research and technical studies conducted by the Explosives and Physical Sciences Division of the Bureau of Mines from July 1, 1949, to June 30, 1950. It is the fourteenth of a series of annual reports whose aim has been to bring to the reader a résumé of the research results that have appeared in published form during each fiscal year under the authorship of members of the staff. These are referred to throughout the report.

Jan 1, 1951

By Seth T. Reese

REPORTS received from operating companies by the Bureau of Mines, United States Department of the Interior, indicated marked progress in the reduction of injuries to employees in the coking industry in 1951 as compared with 1950. The fatality rate (0.14) per million man-hours of exposure declined 33 percent and was the second best performance since statistics on the industry were first collected in 1916. The nonfatal-injury rate (10.94), the best since 1940, declined 8 percent and was bettered only in 8 of the past 36 years. The nonfatal rate is based on all injuries resulting in loss of time for more than the remainder of the day on which the injury occurred. The exposure to hazard, as represented by the number of man-hours of work time during the year, was 7 percent higher than in 1950 and, except for the year 1943, was the highest since 1920. The fatality rate for men employed at beehive-coke ovens decreased 16 percent and the nonfatal-injury rate 23 percent, while the man-hours of work time or exposure increased slightly over 16 percent. The fatality and nonfatal-injury rates at byproduct ovens declined 33 and 2 ½ percent, respectively, while the number of man-hours worked increased 6 percent.

Jan 1, 1954

By James L. Elder

The Bureau of Mines and the Alabama. Power Co. jointly conducted a first experiment in underground gasification of coal at Gorgas, Ala., during the fall and winter of 1946-47. This preliminary experiment showed that it was not difficult to maintain combustion of coal underground, and that coal in place could be completely gasified. It was noted that the high temperature developed by the gasification of coal in place brought about changes in overlying strata that appeared to be favorable to the process. The high temperatures caused the roof rock to become plastic, to expand, and to settle down on the mine floor directly behind the reacting coke face. These results were promising enough to warrant further investigation of the process. It was believed that if this action could be controlled properly with roofs of similar composition, it would tend to force the gas-making fluids underground against the coal faces. Plans for the second experiment were based in part on this favor-able roof action, and the successful operation of the planned initial straightline passages depended on this fact. Gorgas was chosen as the site for the second experiment for the following reasons: A tract of coal land of sufficient size was available and isolated from the main body of coal; the roof rock was similar in composition to that encountered in the first experiment; and the overlying strata were thick enough to eliminate some of the operating difficulties that had been encountered, In addition, power, water, and machine-shop facilities as well as an adequate supply of labor were available in this area, and the friendly cooperation of the Alabama Power Co. further recommended this site for the planned experiment.

Jan 1, 1951

By Sarkis G. Ampian

Published optical microscopic and X- ray diffraction characteristics of the following compounds are critically evaluated and compared with Bureau of Mines data : Tricalcium aluminate , calcium monoa luminate , dodecacalcium heptaluminate , dicalcium silicate , tricalcium silicate , and sodium aluminate . A recommended set of definitive optical and X- ray diffraction characteristics is presented . These values are used to identify products of the lime soda sinter process for production of alumina . Polymorphism of gamma- , beta- , and alpha prime - dicalcium silicate is reexamined , and new data are presented on polymorphism of tricalcium silicate and sodium aluminate by high- temperature X- ray diffractometry . Polymorphism is not observed for tricalcium aluminate , calcium monoaluminate , and dodecacalcium heptaluminate . Bureau of Mines data indicating a stoichiometry of 12Ca0.7A10 for the phase 5Ca0.3A1 0₂ are discussed . A critical review of the literature concerning calcium dia luminate and sodium undecaluminate ( 8 -A10 ) is also included .

Jan 1, 1964

By Lyman Moore

This Bureau of Mines report describes 2nd evaluates iron ore resources in California and Nevada and analyzes the California and Japanese iron ore markets in which these resources will be used. The competitive position of California-Nevada ores, in these markets, was estimated by comparing regional iron ore prices, production costs, and transportation costs with those of foreign suppliers. Resources were determined to be sufficient to produce the equivalent of 585 million tons of 64-percent iron pellets at a price of less than $15 per ton delivered at California ports. Much higher tonnage could be produced at higher prices. Iron ore requirement of the California iron and steel industry will increase to an estimated 15.9 million tons by the year 2000. A study of the iron ore production potential of California-Nevada deposits and of out-of- State sources indicated that this ore requirement can be supplied most economically by California-Nevada ores. Iron ore import requirements of the Japanese iron and steel industry will increase to an estimated 150.0 million tons by the year 2000. A study of price trends in this market indicated that very little California-Nevada iron ore will be sold in Japan after 1973 when existing sales contracts expire. Iron ore-exports might be economically possible if ore could be transported from California to Japan at ballast rates as backhaul on existing petroleum shipping.

Jan 1, 1971

By W. W. Agey

An inexpensive technique that laboratory studies indicated would significantly reduce seepage in irrigation canals was devised and tested through research sponsored by the Bureau of Reclamation and the Missouri River Basin Field Committee. Laboratory tests simulating optimum field conditions determined that easily applied sodium carbonate solutions made test beds of canal lining materials virtually impermeable for long periods. The study comprised alternative laboratory treatments of 3-inch-deep test beds of canal earths with 74 water-soluble chemicals in search of one 01' more that would effectively improve the water barrier characteristics of the component clays. Sodium carbonate, one of the least expensive, was among the most effective. The addition of 0,4 lb of reagent per sq yd greatly reduced the seepage from typical, highly permeable test beds. The reagent penetrated and sealed surface for about a 1.5-inch depth.

Jan 1, 1965

By Constantine C. Popoff

This report reviews and analyzes, by a simple analytical and logical reasoning, the conventional methods of reserve computations of mineral deposits described in various domestic and foreign publications. It brings together, formulates, and evaluates the principles underlying interpretation of exploration data; and ties such principles to the proposed classification of methods. The material is discussed in sufficient detail to allow general application.

Jan 1, 1966

By Stephen M. Jasinski

This report describes the materials flow of mercury in the United States. It examines the mining and production of mercury and the manufacturing, uses, and ultimate disposal of mercury. Materials flowcharts were prepared for 1989 and 1990. An effort was made to include estimates for all major anthropogenic sources including fossil fuel combustion, waste incineration, and nonferrous metal mining operations. Mining and mineral processing released about 100 mt/yr of mercury to the environment in both 1989 and 1990. The combustion o ii fu1s released 175 mt/yr in the same years. The manufacturing, use, and disposal of products containing mercury accounted fix the release of 1,037 mt of mercury in 1989 and 938 mt in 1990. The manufacture of chlorine and caustic soda was a major source of recycled mercury, but it was all reused within the industry. Recovery from all waste products accounted for 36% of reported consumption in 1989 and 42% in 1990. The losses from manufacturing and end use have been declining, whereas mercury emitted from combustion sources has not been strictly regulated and will likely become the largest source of mercury releases to the environment.

Jan 1, 1994