Search Documents

"INTRODUCTION These safety standards for anthracite mines have been prepared for use as a guide for Federal inspectors. They are a revision of ""Tentative Inspection Standards for Anthracite Mines,"" published as Bureau of Mines Information Circular 7282 issued in May 1944 and used as a guide in Federal inspections. No provision made in these safety standards should be construed or operate to nullify any existing State statutes; they are intended to supplement the State statutes in the interest of increased mine safety. Mines are inspected in accordance with the Federal Coal-Mine Inspection and Investigation Act of 1941, Public Law 49, 77th Congress, H. R. 2082. Any unusual hazard noted by an inspector and not covered by these standards will be discussed in the inspection report, and suitable remedial procedure will be recommended.ARTICLE I. - SURFACE STRUCTURESSection 1. Breaker and cleaning plant.Electric switches and controls in breakers and cleaning plants should be enclosed.Where coal is dumped at or near air-intake openings, reasonable provisions should be made to prevent the dust from entering the mine.Section 2. Lamp houseNaphtha or other flammable liquids in lamp houses should be kept in approved containers or other suitable dispensers.Flame safety lamps should be permissible and maintained in permissible condition.Flame safety lamps should be properly cleaned, examined, and assembled by a qualified lamp attendant or other competent person before each period of use. Lamp assembly should again be checked by the person using it immediately before he enters the mine.When not in service, methane indicators, flame safety lamps, and electric cap lamps should be in the custody of competent persons responsible for maintenance and testing."

Feb 1, 1948

By Ulrich Neumann

Mining coal by employing a method called longwall mining is gaining more and more popularity in the United states since it offers many advantages over the conventional deep mining methods. Those advantages are a higher productivity, an almost total extraction of the mineral since no pillars must be left behind for support, and an increase in safety since the personnel are protected by the shield supports and rarely have to work near unsupported, exposed root. However, on some longwalls, the dust levels liberated by various equipment such as belt conveyors, chain conveyors, crushers, longwall shearers, and moving shield supports can exceed the maximum permissible limits and therefore have an adverse effect on productivity. Many attempts have been made over the past years to reduce the dust liberation by changing designs, installing various types of sprays or scrubbers, treating the mine water with wetting agents, or even using foam to catch dust before it becomes airborne. In the year 1984, the Bureau of Mines awarded Eickhoff Corporation a contract to demonstrate a water-jet-assisted cutting system for the multiple purposes of reducing dust levels, improving bit consumption, and increasing material size. During the previous phases of this contract, various trials were conducted aimed to design, build, and test d shearer loader to meet the objective of the contract. In the early stages of the research program, it was expected to see a reduction in the overall power consumption of the machine due to the fact that the high-pressure water jet would pre-cut the mineral in front of the bit. This, in turn, would then reduce the bit wear. Since there is less cutting action performed by the bit, a reduction of the dust liberation and a reduction of product fines was sought.

Jan 1, 1991

By E. C. Lane

"INTRODUCTION The first important discovery of petroleum in New Mexico was near Dayton, Eddy County, where the Brown well was drilled in 1909, and small quantities of oil were produced. In 1911 and 1912 wells were drilled in McKinley County, but commercial production did not begin until the discovery of the Hogback field, San Juan County, in 1922. The discovery well in the Artesia field, Eddy County, drilled in 1923, gave impetus to active drilling in many areas. Since 1924 New Mexico has produced petroleum in commercial quantities and since 1930 the State has joined the ranks of the big produc¬ing States, being sixth or seventh in total production in recent years.Production by years. 1924 to 1940, inclusive, taken from annual figures in Bureau of Mines Minerals Yearbook, are given in table 1. The total production shown is 274,331,000 barrels. Andreas 3/ has published production figures for the year 1940 and a resume of all production to the end of 1940. Data from his report are presented in table 2 for each field sampled. The cumulative production, as given by Andreas, is 270,618,575 barrels."

Aug 1, 1942

By Frederick W. Horton

With large deposits of low-grade molybdenum ore and a latent market for molybdenum, which with development might perhaps equal that for tungsten, the United States has for years made no pro- duction of molybdenum ore worthy of mention. In fact, during the decade previous to 1914, there was no output of molybdenum ore in this country except in 1905, 1906, and 1907, when a few small lots of molybdenite and wulfenite were marketed." To ascertain why this possible source of economic wealth should remain undeveloped, the United States Bureau of Mines undertook an investigation in 1914, with a view of assisting the establishment of a molybdenum industry in this country. A preliminary review of the situation showed the following conditions: Briefly there was a lack of any considerable demand for molyb- denum for the one known use that might consume any large tonnage of it, that is, for the manufacture to certain alloy steels to which molybdenum imparts properties roughly similar to those produced by tungsten. It was at once evident that the market for molybdenum in alloy steels must be developed, or that extensive new uses for the metal must be created, before the demand would be sufficient to war- rant any extensive mining of molybdenum ore. Investigation showed that one of the chief factors in retarding the development of any demand for molybdenum by the alloy-steel trade was that manufacturers who might use, or might investigate the possibilities of using, the metal were kept out of the market by the fear of not being able to obtain steady supplies. On the other hand, those who might be interested in the development of some of the extensive low-grade molybdenite or wulfenite deposits in this country were prevented from doing so by the small visible demand and the fear that any large production would glut the market. Owing to these conditions the mining of molybdenum has in the past been confined almost entirely to small-scale operations on high-grade streaks of molybdenite ore, and the methods of recovery have been limited largely to cobbing and hand picking.

Jan 1, 1916

By R. W. Dougherty

From time to time interest has been evidenced in transporting coal with water in pipe lines. About the year 1895, United States patents broadly covering a method of pumping coal with water through pipelines were granted to W. C. Andrews. His process was used to some extent in pumping anthracite culm and waste back into the worked-out portions of the mines. About 1905, W. T. Donnely was granted patents relating to pumping anthracite silt away from the breakers. From about 1913 until 1924, a British engineer, Gilbert G. Bell, used a short pipeline to convey coal with water from barges on the Thames River to the Hammersmith Electricity Generating Station, London. Minus 5-inch coal was transferred 660 yards through an 8-inch pipe. Some trouble was experienced with fine coal, which tended to plug the line. Bell made several proposals to transport coal by pipeline overland from the Midlands to London, a distance of about 100 miles, but these were never adopted. This survey is concerned mainly with the problems presented by actual pipeline transportation of coal with water. It is assumed that the coal will have been processed to remove most of the abrasive impurities by conventional methods prior to introduction into the line, and that it has been crushed to the required top size. Dewatering at the discharge end of the line is considered part of the conventional cleaning process. There still remain many pump-performance and behavior of water-coal mixture problems that can be solved only by actual performance tests. It is recognized that the distribution of coal to other than very large users is not changed. Large storage areas would be required to supply seasonal markets. Large users, such as power plants and heavy industries, could be supplied by branch lines directly to the point of use, It is also recognized that pipe lines might not be able to carry a full range of sized coal to meet market demands in many areas.

Jan 1, 1951

By J. Douglas Causey

No mines are active in the Hunter Mountain Wilderness Study Area (WSA), and no mineral resources have been identified in the WSA. However, the Monarch Mine has low potential for silver, copper, tungsten, and gold resources in quartz veins; the Shirley Ann Group and Sal Group have moderate and low potential, respectively, for silver, lead, and copper resources in skarn; claims overlying the Eureka Quartzite have low potential for silica resources; and the Tourmaline N1-4 Prospect has low potential for tourmaline resources in quartz monzonite. Copper, lead, silver, tungsten, molybdenum, wollastonite and garnet occur in skarn zones between monzonitic and carbonate units. Silver, tungsten, and copper also occur in quartz veins within monzonite. Known metallic mineral deposits are small, erratic and discontinuous. The J. 0. Mine, adjacent to the northeast corner of the WSA, may contain as much as 26 million tons of subeconomic wollastonite resources. The crest of an open pit to produce that resource would extend into the WSA. No information exists on geothermal potential because no exploration has been done in the area. No occurrences of energy minerals are known within the WSA.

Jan 1, 1983

By Jack Wright

The analysis of water produced with crude petroleum has interested oil producers since inception of the industry. Records of the first analysis of mineralized water produced from an oil-productive formation are obscure, and references to the first use of brine analyses to assist in solving problems of petroleum production are not available in the technical literature. However, many early reports of the Federal Bureau of Mines5-8 and Federal Geological Survey,9-11/ as well as articles in engineer and geological journals12-14/ placed special emphasis on the importance, interpretation, and application of water analyses. One of the earliest applications of water analyses, and still a major one today, is for identification of intrusive waters in oil wells. This may be done by comparing the chemical constituents of a sample of water indigenous to the oil-productive formation with those of samples from upper, water-bearing formations within the same general area. Some earlier investigators recognized the need for Analyzing samples of all waters encountered in drilling operations. Ambrose15/ stated, in part, "In wells being drilled, the engineer should grasp every opportunity to get a true sample of water from each sand. . .," and, "The waters of each oil field are chemically different from those of another field." The validity of the latter observation and the importance of the former one have been borne out by comparing the results of analyses of many samples and noting the differences in relative concentrations of like constituents of waters from the a geological formation in different localities or oil pools.

Jan 1, 1957

By Thomas M. Barczak

The transverse loading requirement for stoppings as specified in the current Code of Federal Regulations is 39 psf. This measure is based on physical testing of a freestanding wall in accordance with ASTM E 72 specifications, where the dominant parameter is the tensile strength of the sealant. A new protocol based on arching has been developed to determine the true transverse load capacity of stoppings. Arching is achieved by the restraint of the stopping against the mine roof and floor, whereby compressive forces are developed within the wall. A laboratory procedure using the NIOSH Mine Roof Simulator (MRS) to simulate rigid-arching of stoppings was developed and verified through full-scale in-mine tests. Using this protocol, a systematic study of the design parameters that affect arching capability in block stoppings was conducted. The study included a theoretical assessment of arching and development of design formulations that can accurately define the transverse load capacity of various stopping constructions under various loading conditions. This approach should lead to a safer mine environment by matching the transverse load capabilities of the stopping design to the requirements in the mine to ensure proper ventilation control is maintained.

Jan 1, 2005

By Peter G. Chamberlain

The surge in gold and silver prices during the 1970's attracted many new mining operators and has rekindled interest among experienced ones. With its low capital investment requirements and fast payout, leaching has attracted many operators--particularly those with small or low- grade deposits. Although in certain situations leaching offers many advantages over conventional mining methods, many operators are uncertain how these relatively new techniques should be implemented. Consequently the Bureau of Mines has prepared this circular to disseminate information on gold and silver leaching practices, techniques, and problem. Engineering data gathered from 26 operations indicate that most ores are leached in heaps following crushing and distribution on pads. Metal values are recovered from cyanide leach solutions using either zinc precipitation or charcoal adsorption. Potential problems that my hamper on block development of a leaching operation are poor percolation characteristics of the ore, calcium salt buildup, low temperatures, and solution losses. An extensive bibliography on gold and silver leaching is appended.

Jan 1, 1984

By Richard D. Miller

This Bureau of Mines publication contains analyses and related source data for 271 natural gas samples from 22 States collected during calendar year 1982. All samples were obtained and analyzed as part of Bureau of Mines investigations of the occurrences of helium in natural gases of countries with free market economies. This survey has been conducted since 1917. The analyses published herein were made by the mass spectrometer and chromatograph. The results of the investigation of the occurrences of helium are published annually to make the information available to the petroleum industry and the general public. Twenty-six publications have presented the results of 13,051 gas analyses vide prior to 1982. The first 3 bulletins (1-3)3 contain analyses and related source data on 5,218 gas samples collected from 1917 through 1960; these bulletins have been supplemented annually by information circulars (4-17, 19-24, 26) containing 7,833 analyses of samples collected since 1960.

Jan 1, 1983

"When a metal-mining company takes out a workmen's compensation insurance policy, it does so to relieve itself of its uncertain and variable financial liability under laps requiring payment to employees for lost-time accidents, there-by passing the liability or to the insuring agency. For this service, or rather for the assumption of the risk, the insuring agency charges the mining company a price, or in insurance parlance, ""a premium"".The insuring agency depends upon a volume and variety of business to average the losses incurred by its individual policy holders, and determines its price to cover losses that are suffered and its cost of doing business.It is generally known that all types of insurance are founded on the theory of probability applied to large groups of risks, Workmen's compensation insurance is no exception, and the average price paid therefor must be based on the frequency and severity of accidents in the particular industry or branch of industry under consideration. The frequency and severity rates are determined by statistics, which, of course, unless standardized, kept carefully and consistently, and analyzed properly, are liable to be inaccurate and misleadingThe importance of large groups in arriving at an average price for insurance service can not be overestimated, For example the writer knows of one small group of some twenty metal-mining companies whose losses during the past two years exceeded their premium charge by 54%. Not a single individual company during the two years kept its losses below the premium rate. For several years the group as a whole has persistently exceeded its premium rate, Such risks are not profitable to the insuring agencies and can only be carried where a large volume of good risks will balance the poor risks, but in order to conform to good insurance ethics the premium rate must be based on averages for the industry as a whole, and kept sufficiently low to induce operators to sell their risks."

May 1, 1924

By N. E. Hanna

To be approved for use in underground coal mines in the United States, explosives and blasting devices must pass certain safety tests prescribed by the Federal Bureau of Mines. These tests are described in Schedule 1-G4/ (explosives) and Schedule 26A5/ (blasting devices). An explosive or blasting device that passes the appropriate tests is placed on the active permissible list. As this list is subject to continuous revision, it has been the practice of the Bureau of Mines to publish periodically the names of explosives and blasting devices that have been added to the active list, as well as those that have been transferred to the inactive list; changes in brand names also are reported. The present circular gives all explosives and blasting devices on the active permissible list as of December 31, 1957, and shows all changes, additions, and transfers in that list between December 31, 1951,6/ and December 31, 1957.

Jan 1, 1958

By J. C. Dumbrille

The following account of wining practices of the Kirkland Late Gold twining Co., (Ltd.), at Kirkland Lake, Ontario, is one of 4 series of papers being prepared by the United States Bureau of Mines on mining practices, methods, sad costs in various districts. The author has prepared this paper with the help and permission of J. B. Tyrrell and W. M. Sixt, the managing director and the mine manager, respectively. This mine is operating at a daily rate of about 150 tons.

Jan 1, 1931

By A. A. Bakewell

This information circular, which describes mining methods and practices at the Baguio Gold Mining Co., Philippine Islands, is one of a series being prepared by the Bureau of Mines on mining methods, practices, and costs. Since January 1952, Baguio Gold Mining Co. has operated its rehabilitated mine and mill in the Baguio district. Postwar labor and supply costs are three or four times prewar costs, whereas ore tenor and tonnage are about the same. Ore reserves remain approximately the same, but deeper and more spreadout operations add to increasing costs. Recently the company has acquired an adjoining property, which may lengthen its life substantially. Costs and general operations are more or less typical of the district, which includes three other active gold mines. Gold ore mined in the district totals approximately 4,300 tons per day.

Jan 1, 1959

"There seems to be some confusion between the terms carbon black and lamp black, although in American lampblack is generally understood to be a soot formed by the smudge process. In this process oil, coal tar, resin or some solid, or carbonaceous substance is burned in an insufficient quantity of air, while on the other hand carbon black is a product resulting from the incomplete combustion of gas and is deposited by actual contact of flame upon a metallic surface.The various carbons, such as gas retort coke, oil retort coke, graphite, carbon black, lampblack, vine black, wood-pulp,black, willow charcoal, and blacks made from refuse material such as leather have different characteristics as to flocculence strength of color, and physical structure. These blacks are made by one of the following methods:(1) Formation by direct contact of a flame upon a depositing surface.(2) Production by combustion of an oil, tar, etc., in an inadequate supply of air; the soot is allowed to slowly settle out on the floors and the walls of the collecting chambers.(3) Carbonization of solids and subsequent reduction to a state of small subdivision.(4) Production by heating carbonaceous vapors or gases to a decomposition temperature by external heating with or without air in the forming chamber. This is usually referred to as cracking or thermal decomposition."

Mar 1, 1920

By Madan M. Singh

The use of fluid jets for industrial purposes has received considerable attention in recent years. The convening of The First International Symposium on Jet Cutting Technology1 in April 1972 devoted solely to this subject probably heralds the coming of age of this new science. It is interesting to note the emphasis in the conference towards the cutting of rocks, minerals, and soils, indicating the attention being devoted to excavation and mining. The use of water streams for mining of minerals is not new. It is well over a century since its first application.2 But its use in coal mining has been somewhat restricted over the years. In the past 30 years the U.S.S.R. has successfully used water for coal extraction, and these techniques have been examined in 15 countries in recent years. In the United States research on various aspects of the method has been conducted for over 15 years,3 but success stories from the Soviet Union,4 JapanS and Canada6 in the last 5 years has spurred greater enthusiasm. IIT Research Institute has done pioneering work in the 7-12 13-15 area of water jetting for rock and coal breakage. It has just completed an experimental study involving mining of coal with a 50,000-psi and 100,000-psi jet in a stripping operation14 under the sponsorhip of the U. S. Bureau of Mines (Contract No. HOll1789). As a complementary program the Bureau initiated a project to design a water-jet coal-mining machine (Contract No. H0133119). IITRI was a successful bidder on this competitive procurement.

Jan 1, 1974

By E. D. Calvert

The Bureau of Mines, in its effort to promote greater utilization of domestically abundant materials, conducted reasearch on an alternate mold material that has commercial potential for titanium investment casting. Using variations of the conventional lost wax molding process, investment shell molds were formed entirely of fused, calcia-stabilized Zr02 and a Zr02-forming binder. Optimization of binder/slurry properties', stucco grain size and dis¬tribution, and curing practices resulted in a structurally sound investment shell that was distortion free and thermally stable. Small titanium castings, weighing up to 10 pounds, were prepared in unheated molds by both static and centrifugal casting techniques. Microstruc¬tural examination of the castings revealed that mold fill and surface quality were enhanced by centrifugal casting, although good results also were obtained from the statically poured molds. Microstructural and electron microprobe examinations showed that excessive, brittle case formation could be avoided by curing the dried shell molds in air for at least 2 hours at 1,400° C. Increasing curing temperature and time above these levels yielded added bene¬fits. Molds fired in vacuum at 1,500° C for 4 hours yielded castings essen¬tially free of case formation. The tensile properties of as-cast test specimens (no surface conditioning performed) id the chemical composition of representative metal samples showed that castings produced were comparable to Grades C-1 and C-2 unalloyed titanium This indicated that no sifnificant degradation of metal properties resulted from mold/metal interaction.

Jan 1, 1981

By J. Douglas Causey

In 1986 and 1987, at the request of the Bureau of Land Management, the U.S. Bureau of Mines studied 73,010 acres of the 76,480-acre Lower Owyhee Canyon Wilderness Study Area (OR-003-110) in order to evaluate its identified mineral resources. The study area is in Malheur County, OR, about 8 miles north of Rome. There are approximately 7.7 million tons of subeconomic zeolite (heulandite and/or clinoptilolite) resources with ammonia ion exchange capacities as high as 1.75 milliequivalents per gram in the Chalk Basin-Lambert Rocks area. The bed is 25 ft thick with less than 100 feet of overburden. This resource probably will not be mined in the foreseeable future.

Jan 1, 1989

By Barton K. Cross

The objectives of this effort were to: 1) Develop and validate start-of-shift operational inspection procedures to be used by operators of mobile, self-propelled equipment used in surface mining operations; 2) Evaluate user acceptance of the developed procedures; and 3) Recommend methods and media for presentation of the developed procedures to the user population. Mobile, self-propelled surface mine equipment requiring start-of-shift inspection was identified. Subsystems amenable to operational inspection were identified. The procedures addressing all safety critical subsystems on each equipment type were then developed and validated. The inspection procedures developed were those that could be performed largely from the operator's station. User acceptance was evaluated during on-site data collection visits to surface mines. Representatives of the user population reviewed the procedures and were then interviewed. Recommendations for the methods and media of presentation to the user population were developed from information obtained in: 1) Review and analysis of instructional technology literature applicable to this area; 2) On-site data collection; and 3) Analysis of the working environment and characteristics of the user population.

Jan 1, 1977

By A. W. Fahrenwald

The art of flotation has developed rapidly. Numerous technical staffs and individual investigators have, by their combined efforts, developed practicable methods of concentrating ores which ten or even five years ago were considered complex and impossible of commercial treatment. Also the work of those who have been engaged in pure research on the fundamentals of flotation has helped greatly to expedite the general development of the process. However, in spite of the highly successful practical operation of the flotation process, results are obtained and things happen that we are unable to explain completely, although much is known about the theory of the process. The rapid stride in flotation concentration, it is noteworthy to point out, is due to the freer exchange of facts and data by the staffs of the larger mining companies and the patent controlling corporations, and by investigators in general. Generally speaking, one may visit any mining plant and by presentation of proper credentials, be shown all that is going on or that is being done.

Jan 1, 1925