Search Documents

The Bureau of Mines conducted large-scale laboratory copper ore leaching tests to enable improving copper recovery from large dump-leaching operations. This was done by comparing leaching progress when copper was recovered from recycled leach liquor either by cementation or by solvent extraction. Copper was leached from 7-ton ore samples at room temperature using pH 2 ferric sulfate solutions. With are samples containing 11 percent minus 0.5-inch fines, no marked advantage in using either of the copper recovery methods was evident after 416 days of leaching. With ore containing 32 percent minus 0.5-inch fines, solvent extraction of copper was advantageous in that 60 percent of the copper was extracted after 568 days, whereas only 48 percent of the copper was extracted when cementation was used. Less acid was consumed during leaching when solvent extraction, rather than cementation, was used for copper recovery. Iron, contributed by cementation with scrap iron, plugged the ore bed containing 32 percent fines.

Jan 1, 1981

By W. S. Sanner

Anthracite was used extensively as a fuel in iron metallurgy from 1840 to 1880. In 1874, 226 of the 680 blast furnaces in the United States were operating on anthracite and producing almost one-half of the Nation's pig iron. However, by 1890, railroad expansion, the development of western iron-ore reserves, and the growing use of coke decreased the importance of anthracite as a metallurgical fuel. As a result, the last blast furnace designed exclusively for anthracite use was built in 1891. Because of the increased energy requirements of our expanding national economy, the abnormally high demands during national emergencies, and the proximity of anthracite deposits to eastern steel-producing areas, interest has grown in again using anthracite in iron metallurgy. Estimates of anthracite reserves indicate a 300-yr. supply at a production rate of 30 million tons per year. These large reserves dictate the development of an adequate technology for the use of anthracite by the metallurgical industry.

Jan 1, 1961

This study of underground mine water inflow was initiated by the U. S. Bureau of Mines in March 1980. The objective of this study is to evaluate the hydrologic variables associated with surface water and ground water systems that affect the inflow of ground water into an underground mine. Data collection techniques are reviewed for their applicability for quantifying these hydrologic variables. Innovative techniques are also investigated. Existing analytical and numerical procedures for predicting underground mine water inflow are reviewed and evaluated. Over 300 computer models were reviewed for their applicability to modeling underground mine water inflow. The model UNSAT2 is utilized for modeling inflow to a shaft and tunnel or drift. This model and the techniques developed in this study are applied to two existing mines.

Jan 1, 1982

By R. Ward Stahl

Fire is still a scourge of the mining industry, although many precautionary measures have been and are being taken to reduce the incidence of fires and to combat them. Generally, the success of fire extinguishment is directly proportional to the speed of attack, and the speed of attack in turn is dependent upon the availability of materials and trained personnel. Preparations for firefighting are frequently neglected because they are considered emergency needs and do not contribute directly to coal production. Fire incites panic--a fact often overlooked--but such chaos can be minimized by training people in the use of equipment and procedures. Heat, smoke, and fumes hamper the approach to a fire; however, a relatively new technique of attacking fires with high-expansion foam may well contribute greatly to firefighting. The foam is transported to a fire and used at a considerable distance, thus permitting the firefighters to work more safely.

Jan 1, 1962

Humankind's interest in measurement of human physical strength probably dates to the first humans. At that time, life was truly a struggle in which the fittest survived. To a great extent, fittest meant strongest. Interestingly, current interest in human physical strength in the workplace stems from 1970-1980s vintage research demonstrating that persons with adequate physical strength are less likely to be injured on physically demanding jobs. Survival in many modem workplaces may still be a case of survival of the strongest. There is, however, a flip side to this issue - that persons with limited strength are more likely to be injured on "hard" jobs. To address this problem, we can apply what we know about physical strength to job design. "Hard" jobs can be redesigned to be within the physical strength capability of most people. Since physical strength is important to these jobs, we must find ways to quantify it through testing. This publication concerns human physical strength testing. Its purpose is not to recommend any particular type of testing, but rather to describe the types of testing available and their uses. It is up to each individual user of strength testing to decide which testing technique is most appropriate for his or her particular application. This booklet discusses four types of strength testing: isometric, isoinertial, psychophysical, and isokinetic. Human Strength Before describing the different types of strength measurement, we must define the term "strength" and explain the concept of strength measurement. Strength is defined as the capacity to produce force or torque with voluntary muscle contraction. Maximum strength is defined as the capacity to produce force or torque with a maximum voluntary muscle contraction.(1,2) These definitions include some key words that must be explained. A voluntary muscle contraction is "voluntary." When a person's physical strength is measured, only the effort the person willingly puts forth at the time is measured. Thus, when we test a person's "maximum strength," we are not measuring his or her actual maximum, but some lesser value representing what he or she is comfortable expressing at the time with the existing equipment and environmental conditions. Interestingly, when researchers startled persons being tested (e.g., by setting off a starter's pistol behind them), they have found significant increases in measured strength.(3) It has been hypothesized that the lower strength displayed during normal testing provides a margin of safety against overloading and damaging muscle tissue. The test equipment and the tested person's familiarity with the process also influence the "voluntary" strength output. The interface between the tested person and the test equipment is particularly important. A poorly designed interface induces localized tissue pressures that vary from uncomfortable to painful. In this situation, testers are measuring voluntary discomfort tolerance - not strength. It is important for strength researchers to keep the "voluntary" nature of their data in mind when they are designing their equipment and protocols.

Jan 1, 1998

By Gary Friedline

As a consequence of the Coal Mine Health and Safety Act of 1969(PL91-173), the Bureau of Mines (BOM) entered into a contract with Ocean Energy Inc. (OEI) to develop, fabricate, install, and evaluate a permissible lighting system for use on a longwall coal mining operation. The program schedule is shown in Figure 1.1. The proposed regulations are contained in Appendix A. The initial part of the program involved a survey of existing longwall lighting practices in Germany and England and an evaluation of a variety of lighting components on a mockup of a longwall mining operation that was fabricated under this program. Visits made to German and British mines uncovered major differences in lighting level requirements, permissibility aspects, size, and operating constraints which identified wide disparities and essentially eliminated from further consideration any known imported lighting devices for meeting the higher lighting levels and standards proposed for US coal mines by the Mining Enforcement and Safety Administration (MESA). The longwall mockup provided use¬ful information regarding the amount of illumination required, physical size and shape of lamps, light distribution problems, cable routing, use of connectors, signaling, glare, and other important factors unique to the lighting of low coal longwalls.

Jan 1, 1975

By John C. Machisak

This publication, for the calendar year 1959, contains statistical data on injuries and employment pertinent to metal mines, ore-dressing plants, and primary nonferrous smelters, refineries, and reduction plants. The Bureau of ,Mines is authorized to request data on injuries and employment in the metal-mining industry, and the information, voluntarily submitted by the operators, contributes immeasurably to the promotion of safety in the metal- mining industry. Every effort has been made to make the annual canvass as complete as possible. The data presented are classified according to the hind of ore mined and includes information on copper, iron, lead-zinc, gold-silver lode, placer, uranium- vanadium, and miscellaneous metals. A breakdown of miscellaneous metals by commodity is shown in tables 17 and 18.

Jan 1, 1963

By John C. Machisak

This publication, for the calendar year 1959, contains statistical data on injuries and employment pertinent to metal mines, ore-dressing plants, and primary nonferrous smelters, refineries, and reduction plants. The Bureau of Mines is authorized to request data on injuries and employment in the metal-mining industry, and the information, voluntarily submitted by the operators, contributes immeasurably to the promotion of safety in the metal-mining industry. Every effort has been made to make the annual canvass as complete as possible. The data presented are classified according to the hind of ore mined and includes information on copper, iron, lead-zinc, gold-silver lode, placer, uranium- vanadium, and miscellaneous metals. A breakdown of miscellaneous metals by commodity is shown in tables 17 and 18.

Jan 1, 1963

By H. A. Wright

This report assesses the economic, legal, institutional and technical factors that affect the current and future status of implementation of mine monitoring systems in the United States. It begins with a description of a poll of the Mining Production Research Committee and the Mine Monitoring and Communications Committee of Bituminous Coal Research that was conducted to establish industry monitoring needs and constraints. Existing systems in the United States and foreign countries are then reviewed and compared with the requirements set forth by the industry committees. At the same time, state and federal mining laws are reviewed, and equipment currently available from suppliers of mine monitoring systems and components is discussed. A framework for cost/benefit analysis is established and a series of case examples for various monitoring functions are presented. The total values of the market for mine monitoring systems in 1980 and 1990 are estimated on the basis of industry statistics and system cost estimates.

Jan 1, 1982

By A. C. Fieldner

"Gas hazards may be divided into two principal classes- namely (1) inflammation and explosions; (2) asphyxiation and poisoning. Inflammation and explosion are prevented first by adequate ventilation so that gas sufficient to propagate flame or explosion can not accumulate, and second, by avoiding sources of ignition such as open lights, flames, sparks, electrical arcs, short circuits, or sparks. Ventilation is also the best preventive measure against asphyxiation and poisoning from toxic gases. When men must enter unventilated or poorly ventilated places containing poisonous or asphyxiating gases, suitable gas masks, hose masks, or oxygen breathing apparatus should be worn. As a rule, loss of life and property from gas hazards is due to ignorance of the properties and hazards of various gases commonly used, and consequently a failure to use proper measures for eliminating and meeting these dangers. It is the purpose of this paper to describe briefly the common gases and vapors with respect to the hazards involved in their use and to discuss the necessary precautions and methods for avoiding these dangersLight, heat, and power are prime essentials of our modern industrial civilization. The combustible gases and vapors used for the production of these necessary elements of our existence comprise the largest and most common group of domestic and industrial gas hazards. Almost every individual in his daily life subject to possible danger from asphyxiation, fire, or explosion due to one or more of these gases. For evidence one need only refer to the daily newspaper where headlines such as the following are frequently seen; ""Family asphyxiated by carbon monoxide from gas heater;"" ""Schoolhouse wrecked by gas explosion in basement;"" ""Man killed by automobile exhaust fumes in his garage;"" ""Fireman overcome by smoke fumes in basement ""Woman"".""Boman severely burned by accidental ignition of gasoline used in cleaning gloves;"" and 'in recent Years we often see ""Building wrecked by explosion of still in residential district.""It will be noted that these accidents are due to inflammation, explosion, or asphyxiation. Any combustible gas or vapor, when mixed, with air or oxygen within certain limiting proportions, will explode on ignition. The violence of the explosion varies with respective proportions of air and gas, and with the degree of confinement of the mixture. For example: Mixtures of natural gas and air containing between 4.5 and 12 per cent natural gas will explode, or propagate flame throughout the mixture without the continual presence of the source of ignition that started the inflammation. The table following gives the explosive limits of the common combustible gases and air:"

Jun 1, 1926

By Ren G. Dong, Richard McCormick, Dan E. Welcome

Vibration exposure at workplaces is generally multi-axial. The health effects of vibration exposure also likely depend on the vibration direction. Therefore, there is a wide interest in the simulation of multi-axial vibration in laboratory experiments. Advances in technology have led to the development of a new 3-D test system for studying hand-transmitted vibration exposure and health effects. The purposes of this paper are to introduce the system and to present the results of its preliminary evaluations. Test System As shown in Figure 1, the system is basically composed of three vibration generators, a multi-axis vibration control system, instrumented handle, handle fixture, and shaker-fixture linkages (stingers). [ ] Figure 2 shows the array of three vibration generators (MB Dynamics, Energizer BLACK-500 lbs) and their associated support bases and foundation developed by MB Dynamics (Cleveland, USA), which create the 3-axis simultaneous motion. These electrodynamic exciters are powered by power amplifiers which provide current proportional to the analog drive signal from a controller. The controller (JAGUAR Multi-Input/Multi-Output closed-loop vibration controller) was provided by Spectral Dynamics, San Jose, California, USA). NIOSH-designed instrumented handle was equipped on the system.

Jan 6, 2006

By Peter Swanson, John Rettkowski

As part of a research program to reduce injuries and fatalities in the U.S. mining workforce, NIOSH is investigating the potential use of noncontact vibration measurements to identify hazardous ground fall conditions. In the present study, the effectiveness of remote vibration sources in exciting resonant responses in damaged structures is examined. Initial experiments were performed on a damaged concrete slab in a controlled environment. Vibration response was measured with a laser Doppler vibrometer using both single-point and two-dimensional array recordings. Excitation sources included direct mechanical impacts to remote portions of the slab and a remotely located industrial demolition hammer. Surficial damage was effectively delineated with both sources through visualization of vibration response in spectral bands selected to discriminate wave propagation from large-scale slab resonance effects.

By Stephen C. Tadolini, Gabriel S. Esterhuizen, Anthony T. Iannacchione

A Major Hazard Risk Assessment (MHRA) was developed in Australia after a series of mine disasters in the 1990’s. A MHRA is used to help prevent major hazards, i.e. fire, explosion, wind-blast, outbursts, spontaneous combustion, roof instability and chemical and hazardous substances, from injuring miners. A MHRA is a structured process that identifies the characteristics of major hazards, assesses and ranks the risk they present, and evaluates engineering and administrative controls to mitigate them. These controls typically consists of a broad spectrum of prevention, monitoring, first response, and emergency response techniques and helps to move an operation from a reactive to a proactive approach towards safety. This paper documents a MHRA performed at an underground mine where strata instabilities and fire hazards may threaten the condition of its escapeways. The objective of this MHRA is to 1) identify what hazards could affect the egress through the mine’s escapeways, 2) determine what unwanted events pose the greatest threat for the mine, and 3) recommend a plan to prevent or recover from the potential disruption of egress through the escapeway. The plan provides information on the key existing controls that should be monitored and audited, and makes recommendation of new potential controls to further reduce related risks. By documenting the use of MHRA to this specific ground control issue, this paper provides a framework for others to judge the merits of this approach and to help design and perform these activities.

By C. B. Kenahan

The Bureau of Mines is developing methods for reclaiming the metal and mineral values contained in municipal incinerator residues. This report describes the first phase of the research, in which reliable methods for sampling and analyzing municipal residues were established and the composition and characteristics of the residues were determined. Samples were obtained from a variety of grate-type furnaces and also from a rotary kiln furnace. The samples were processed on a batch basis and separated into their natural categories by a variety of methods including screening, magnetic separation, air separation techniques, and handpicking. The main components of the residues were determined to be metal and metal oxides, glass, and ash.

Jan 1, 1968

By George A. Morgan

Output of minerals was insignificant in 1981 and made a negligible contribution to the gross national product (GNP), estimated at $1.2 billion.2 Agriculture accounted for 40% of CNP and manufacturing accounted for 10%. The chief source of income was indirect taxes levied on traffic through the Port of Cotonou, an entrepôt. Trade statistics for Benin were incomplete and dated. Major trading partners were France and other members of the European Communities. Benin was a member of the West African Monetary Union and as such must coordinate its foreign currency, reserves, interest rate structure, and fund transfer with other member countries. Its currency, the Communauté Financière Africaine franc (CFAF), was fixed to the French franc.

Jan 1, 1983

By R. V. Ramani, J. M. Mutmansky, P. C. Luna, V. A. Marple, Honglin He, B. A. Olson

The development of a sampling instrument for the assessment of an underground coal miner’s exposure to airborne respirable coal mine dust on a continuous and real-time basis has been long identified as essential for timely initiation of control actions. A respirable dust dosimeter (RDD) which operates on the principle of increasing pressure across a filter media with increasing dust mass on the filter has been developed by the National Institute for Occupational Safety and Health. Comparisons of the performance of the RDD with an U.S. approved gravimetric respirable dust sampler (GRD) have shown that the RDD may meet the requirements for measuring miners’ exposures on a cumulative, near real-time basis such as mid-shift and end of shift exposures. Recently, the performances of the RDD and GRD were compared by conducting side-by-side area sampling experiments in a controlled experimental environment in the laboratory and in underground coal mines under normal operating conditions. In this paper, the results from the in-mine study are presented and discussed. The experimental design for the in-mine study included two mines in different coal seams in different geographic coal regions. To ensure a wide range of concentrations, the experiments were conducted in a continuous miner section in Mine 1, and a longwall face in Mine 2. Airborne dust sampling was conducted for four different shifts at each mine. In each shift, two samples of different exposure durations were collected from two different locations. Each sample consisted of the readings of three dosimeters and the exposed filters from the three paired GRD samplers. As a result, a total of 96 comparative samples were obtained, 48 for each mine. The data were analyzed for the precision of the RDD and GRD measurements and for the relationships between the differential pressure of the RDD and the mass of dust on the paired GRD filter. The analyses indicate that, on the average, the RDD and the GRD track the airborne respirable dust concentrations well, exhibiting both a high correlation between the two measurements and a reliable predictive relationship of one from the other. Details of the experimental design, data analyses procedures, results, conclusions and recommendations of the underground experiments are presented in this paper.

By John J. Sammarco

The U.S. Bureau of Labor Statistics reports that the mining industry has the highest average annual fatality rate (31.9 per 100,000 workers) among all major American industry. To address this, a major research program to reduce hazard exposure of miners with computer-assisted mining equipment was initiated by the U.S. Bureau of Mines.1 One application involves the manual process of extracting and hauling coal where operators, in the tight confines of a mine, can be struck or caught by mobile machinery. The approach to remedy this problem uses a guidance system on the haulage equipment so that it follows the machine that extracts coal. This, in essence, involves sensor-based docking of the machines. Sensors that can survive the hostile mine environment of dust, methane gas, and water, play the key role. Computer analysis of the mining machine's movements and empirical machine characterizations were conducted to establish operating requirements and spatial limitations to ensure proper loading of coal into the haulage equipment. These data served in the selection of a sensing system. Various technologies such as scanning laser systems and ultrasonic sensors have frequently been used in other applications but were found unacceptable. However, a near infrared (IR) sensor employing active targets met the requirements. The sensor has a nominal 75° conical field-of-view and a range from 0.1 to 18.0 m. For the single target mode, nominal range accuracy was 4.3% at a distance of 3.56 m. Correction algorithms were generated reducing the error to 0.6%. Airborne dust testing showed less than 0.8% accuracy (worst case) degradation at levels exceeding (by a factor of 7.5) concentrations permitted by Federal law. The sensor can track multiple active targets providing five degrees-of-freedom (DOF) measurements. Using four targets, the nominal range accuracy was 0.4% without correction algorithms. A guidance system for the haulage system to follow the mining machine does not exist commer¬cially. Such a system can reduce fatalities and injuries by current haulage mining equipment, and is a viable alternative to current haulage control.

By Joseph D. Davis

Selection of a suitable coal or coals for the manufacture of coke of desired quality with due consideration of the purpose for which the coke is intended requires careful thought, and often it will pay to go to consider able expense in testing such coals as may be available. In general it will always be possible to obtain a satisfactory coal or blend of coals for the particular purpose in view, but in some places the cost of transportation would be prohibitive. It may then be necessary to consider a coal or coals inferior in grade, rank, or both. At times, in fact, only one inferior coal may be available, when the problem becomes mainly one of selecting equipment and operating conditions best adapted to that coal, keeping in mind that the end product of the plant must compete with the imported product in the market the plant will serve. This applies particularly to new projects for which it is necessary to build a plant and start with a clean slate, so to speak. However, it will pay every coke-plant manager to employ a force to continually test the coals used and the coke produced to make sure that the quality is not changing appreciably. Furthermore, if the supply of coals used becomes exhausted it will be necessary to use other coals. Continual testing is particularly necessary at plants using borderline coals or blends, where slight changes in the composition or in operation of the ovens may render them dangerously expanding. In this connection it should be stated that control in the newer coke plants is considerably easier than for those built a decade or so ago, consequently in the new ovens a given operating program can be maintained more precisely. This point is important, because one of the main requirements of the coke user is uniformity in both physical and chemical characteristics. For example, any appreciable changes in the quality of coke delivered to the blast?-furnace operator will involve changes in operation if the best results are to be obtained. Such changes are expensive usually they take considerable time and involve production of inferior iron.

Jan 1, 1942

By Franklin D. Cooper

The value of nonfuel raw mineral production in the United States for 1977 increased over that of 1976 by 5%, from $16.7 billion to $17.5 billion. Metals declined by 5% from $6.1 billion to $5.8 billion, chiefly because of strikes in the iron ore industry and a depressed copper market. Subsidization of mining industries in some foreign countries accounted in part for the excess of copper and some other metals on world markets. Weak metal markets and continued slowdowns in the world economy were the main reasons of the virtual absence of new mine projects. Increasing domestic governmental involvement affecting mineral industry activities, such as pricing controls, public land withdrawals, and the Surface Mining Control and Reclamation Act, effective August 3, continued to be controversial and to be criticized by various segments of the industry.

Jan 1, 1980

By T. H. Jeffers

The U.S. Bureau of Mines has developed porous beads containing immobilized biological materials for removing metal contaminants from waste waters. The beads, designated as BID-FIX beads, are prepared by blending biomass, such as sphagnum peat moss or algae, into a polymer solution and spraying the mixture into water. Laboratory studies were conducted to determine bead sorption and elution characteristics. Batch and continuous tests demonstrated that BIO-FIX beads sorbed arsenic, cadmium, lead, and other toxic metals from acid mine drainage waters collected from several sites. Selectivity for heavy and toxic metal ions over calcium and magnesium was demonstrated. The beads exhibited excellent metal sorption and handling characteristics in stirred tanks, column contactors, and a low-maintenance passive system. The sorption process was reversible, and metal ions were eluted from the beads using dilute mineral acids. Cyclic tests indicated that the beads continued to extract metal ions after repeated loading-elution cycles.

Jan 1, 1991