Search Documents

By Robert L. Brooks

Blasting liability problems are frequently compounded by a company's inability to effectively communicate with concerned property owners and the lack of adequate complaint documentation. Often, by the time the insurance carrier becomes involved in a blasting claim, the situation has deteriorated to the point that a solution agreeable to both parties is virtually impossible to reach. The insurance carrier, wishing to minimize their lose potential may decide to pay on a somewhat questionable blasting claim rather than be drawn into lengthy civil proceedings that would ultimately end up in front of a jury with little chance for a successful outcome.

Jan 1, 1992

By Kenneth Medearis

There is considerable evidence that more rational damage criteria need to be generated with regard to low-rise structures subjected to blasting vibrations. There is not sufficient basis for specifying a maximum ground particle velocity damage criterion such as 2 inches/second. A peak ground velocity guideline does not currently take into account a number of significant parameters, including the predominant frequencies of the ground motion excitation and the structure being excited. Although a number of states have adopted, or are adopting, maximum particle velocity criteria, such criteria have been ruled inadequate in certain legal decisions affecting blasting operations. The development of more rational damage criteria is thus of significant importance.

Jan 1, 1978

By Fred M. Nicol

"Large volumes of data derived from numerous logs become too cumbersome to beefficiently analyzed. Blasters can use computers to list and hold blast data and greatlyexpand their capabilities."

Jan 1, 1993

By W Russell

This is an account of Cominco's explosives development work spanning 20 years from the introduction of ANFO into underground operations through to the present day where the use of blasting agents and sophisticated detonation systems create improved safety and blasting efficiency.

Jan 1, 1982

By Michael J. Sapko, Eric S. Weiss, Richard W. Watson

As part of the Bureau of Mines research into the hazards associated with the mining and processing of oil shale, experimental mine tests have been conducted to evaluate preferred combinations of explosives and inerting materials to prevent ignition of oil shale dust and mixtures of oil shale dust and methane.

Jan 1, 1989

By Richard L. Ash

A question that frequently arises during litigation concerned with accidents or alleged damages involving blasting is "were the explosives used according to the best known standards"" The question is not confined to only law suits, however, but also everytime poor blasting results occur. Unfortunately, general guidelines that can be used to define what may be considered as proper practice have not been established by any responsible body upon which to base a reliable Judgment; more often than not decisions are made primarily according to personal opinion.

Jan 1, 1975

By Donald H. Matthews

Drilling and blasting is an every day, sometimes routine activity, that is always fraught with catastrophic capabilities. Under the best conditions it is hazardous, time consuming and expensive. Under the worst conditions it may be impossible to perform by any but the most skilled specialists. Under all conditions drilling and/or blasting jobs are relatively difficult and require specialized equipment, materials and skills that are uncommon. This paper reviews some-of the jobs and problems handled by one drilling and blasting specialist to show the many varied types of problems requiring the services of specialists.

Jan 1, 1976

By Kenneth Faroni, Catherine Aimone-Martin, Thomas Gelormino

A blasting improvement program began in 1985 at two traprock quarries in Connecticut to reduce the levels of ground motions and airblast measured at residential structures surrounding the operations. The quarries are situated within town limits, adjacent to a number of historical and other structures. Although blasting vibration amplitudes were found to be far below those that could produce cosmetic defects in structures, they were perceived to be the cause of structural defects observed by homeowners. Based on a comprehensive * review of blasting practices in place during1985, an extensive vibration monitoring program was implemented. The initial study included the instrumentation of selected residential structures to record and analyze strains imposed within structures from quarry blasting, environmental changes, and from daily household activities. A comparison of the results was made with the results reported by the U.S. Bureau of Mines in 1980. The highest strain imposed in drywall from blasting (13 J_I strain) was 12% and 1% of the highest strain levels recorded for normal household activities and temperature changes, respectively. The present philosophy in production blasting is to attempt to keep vibration amplitudes as low as practical by implementing state-of-art blasting control techniques. Currently, blasting seismographs are placed in a circular manner around each quarry, providing production blast vibration records for 360 degrees of coverage at distances of 2500 to 4000 ft. from blasting operations. Seismograph and production blast records are analyzed each year and become part of a Blasting Improvement Plan submitted to the local zoning commission as part of the annual operating permit process. This paper summarizes the results of previous vibration monitoring programs and outlines the modifications made to blasting practices to minimize the levels of ground motions and airblasts. The public relations efforts and standard corporate procedures used by company personnel to address all blast related complaints and alleged damage claims since 1985 are also discussed.

Jan 1, 2000

By Jair Alarcón, Lucas Steffen, Leopoldo Muñoz

Flyrock is one of the most significant hazards associated with blasting in open pit mining, especially for blasting operations near communities. Flyrock can lead to severe injuries, fatalities, and property damage, compromising the license to operate. For this reason, defining exclusion zones is critical to ensure the safety of people and equipment. A very large radius will reduce the risk of flyrock; however, excessive exclusion zones can significantly impact the productivity of the operation and, in some cases, compromise the extraction of ore in critical sectors. Many mine sites use distances derived from pre-established standards, experiences from other mines, or still use simple methods for analysis, like recording blasts with a terrestrial camera and performing deterministic calculations to determine exclusion areas, applying an arbitrarily safety factor for people and equipment. In this paper we present a new approach that allows the calculation of the exclusion zone by measuring critical flyrock parameters with a high degree of accuracy through a new video analytics technology, this data then is used as input to calibrate probabilistic flyrock models to have more robust calculations, allowing optimized and safe exclusion zones. The proposed methodology leverages high-accuracy data and continuous monitoring to dynamically adjust D&B designs and exclusion zones, ensuring maximum safety without unnecessarily restricting operational efficiency. A case study is presented where the application of these new digital technologies allows precise prediction and control of flyrock trajectories, enhancing the accuracy of exclusion zone boundaries. In this case we successfully reduced the exclusion zone radius to 100m, allowing the ore extraction in a critical region close to the community safely. The study shows notable improvements in safety and productivity, including zero flyrock incidents and enhanced protection for nearby communities. The adaptive nature of these digital tools offers scalable solutions for various blasting environments. The paper concludes by recommending the integration of these tools into standard blasting protocols, highlighting the potential for widespread adoption in the industry to mitigate flyrock risks effectively.

Jan 21, 2025

By Natalie Zeleznik, Brian Hawkins, David Bradley, Rachel Gooding, Patrick Wilson, Brian Somes, Kevin Wegman

"To perform a probabilistic risk assessment (PRA), a method of quantifying the risks associated withinfrequent high consequence events, consequence models that generate representative estimates of human health consequences for a wide variety of representative scenarios are commonly used. Criteria that suitable models must possess include: (1) input requirements necessary to generate large volumes ofprobabilistic simulations; (2) the capability to output injuries with the necessary details and resolution;(3) the ability to capture the variety of different scenarios inherent in an assessment; (4) acceptable cost and computational requirements; and (5) sufficient stakeholder buy-in for community acceptance."

Jan 1, 2017

By R Malo, A Yetter

The use of large diameter blastholes for underground mining began approximately twelve years ago and are now routinely employed in a variety of ore types and stope designs. These large boreholes, ranging in size from 4 1/2 inch to 8 inch diameter, were first utilized in the same fashion as in open pit bench drilling. However, a variety of changes quickly followed in order to accommodate the unique conditions encountered while using a blasthole sloping method.

Jan 1, 1984

By Dale Ramsey

Located in the Chestnut Ridge Mountains of Southwestern Pennsylvania, the Casparis mine named for the founder Kenneth Casparis operated from 1916 until the early 1950. producing crushed stone for construction and railroad ballast. The rock was transported by aerial buckets to a railroad tipple nearly 1000’ (304.80 meters) below the mine. The mine property is now owned by the Pennsylvania Game Commission and is located in the Loyalhanna limestone seam with 4 primary entries that are approximately 40’ (12.19 meters) high by 30’ (9.14 meters) wide and extend over 2 miles (3.22 kilometers) into the mountain.

Jan 1, 2006

By C. Breeds, K. Jeremiah, E. Jennings

Washington State has a well developed set of blasting regulations which have been promulgated by the Department of Labor using extensive stakeholder input, not only from citizens but also from manufacturers and representatives of IME, blasters in charge, blasting engineers, blasting companies, local and federal law enforcement agencies, fire officials, and local and state government representatives. WAC 296-52 therefore provides a foundation or platform for developing city ordinances for Washington State cities should a City wish to do so. On the other hand, Oregon’s code is based on OSHA 1926, Subdivision U, Blasting and the Use of Explosives which provides scant direction regarding the modern use of explosives. Reference is also made to ODOT Section 00335 - Blasting Methods and Protection of Excavation Backslopes. This paper examines two separate programs that have been developed by two Cities, one in Washington State and one in Oregon to further regulate blasting inside City limits and discusses why the lack of a regulatory foundation made one approach more difficult than the other. One of the authors was retained by the City of Kennewick, WA to develop their ordinance and has more recently followed and reacted to a pending ordinance for the City of Redmond, Oregon. The paper will compare and contrast the different approaches and comment on the reaction from both Blasters and the public. We also present a case study that involved blasting in an urban area of Oregon to prepare a foundation for a water tank. Controlled Blasting was carried out within 70-ft of residencies and within a community that had expressed reservations regarding blasting even though the work would make a significant contribution to the betterment of the community. Pre-construction surveys of residencies located in a large area surrounding the site were performed and a well-planned blasting program was carried out. Residencies were subject to vibration levels that were monitored using six seismographs that surrounded the site and these units measured vibration levels that were significantly lower than allowed by statute. There were complaints triggered by individuals reactions to blast vibrations which validated commonly held models of human perception but no damage was caused by the Blasting.

Jan 1, 2024

By Lewis L. Oriard

This paper describes the process of developing blasting specifications for 850 miles of new pipe trench running parallel to an existing high-pressure gas pipeline, often with as little as 14 ft to the existing pipeline trench. The primary method of preventing damage to the existing pipeline was the use of fracture (overbreak) control.

Jan 1, 1994

By J. -P. Tshibangu, E. Lefebvre

ABSTRACT : The Tournai’s region in Belgium is characterized by outcrops of limestone that were mined out long ago by different companies for cement and crushed materials. The region is densely populated and the vibrations generated by blasts in the quarries are of big concern. The occurrence of electronic detonators and development of computer sciences brought a new expectation in controlling the vibration level and, hence, carry out bigger blast operations. In this paper we present the results of two experimental blast programs that have been carried out by the Nobel explosive Belgium Company on the Gaurain-Ramecroix quarry to understand the effect of the delay on the vibrations generated in the neighborhood. The first program has been implemented during the early use of electronic caps in Belgium (1996) by performing some unit shots. An attempt to model the effect of the production blasts by the hybrid method (Hinzen 1988) gave promising but poor results compared to infield measurements. A new program (more than ten blasts) has been implemented in 2006 in which the delay and blast firing sequence (i.e. the order in firing adjacent holes in a row) have been changed; a new attempt is made to build unit signals by deconvolution and then try to model production ones. A comparison of the two approaches is made.

Jan 1, 2008

By L D. Lawrence, W B. Sudweeks, J Bailey

Modern era urbanization is presenting at least one category of explosive consumers with a growing concern for ecological and environmental problems associated with their blasting processes. The construction industry is now, more than ever, being closely monitored with regard to its use of high explosives. In particular, contractors excavating the countless thousands of miles of various trench lines required for virtually every major new construction development taking place in America are being more closely scrutinized by local, state, and federal authorities with regard to blasting practices.

Jan 1, 1988

By William Everett, Jack Eloranta

United Taconite is an iron ore mine operated by Cleveland-Cliffs Inc (Cliffs) located near Eveleth, Minnesota. The mine, originally known as Eveleth Taconite Mines, was purchased in December 2003 by Cliffs (70%) and Laiwu Steel (30%). The mine site, known as the Thunderbird Mine, produces taconite ore for delivery by rail to the company’s Fairlane plant, located approximately 10 miles to the south near Forbes, Minnesota. At the plant, the crude ore is ground, concentrated and processed into pellets for steel industry customers. Total pellet production capacity is about 5.4 million long tons (Ltons) per year.

Jan 1, 2006

By Mark S. Stagg, Norman S. Smith, Rolfe E. Otterness, Stephen Rholl

Blast design parameters were studied in an attempt to quantify their relationship to rock fragmentation. The Bureau of Mines conducted a series of 29 reduced-scale shots at the University of Missouri-Rolla's experimental mine with bench size from 40 to 80 inches. Design parameters varied were burden, spacing, explosive diameter and stemming-explosive length. The shots had 3 or 4 blastholes fired at delays of 1-4 ms per foot of burden, based on previous tests that showed hole interaction could improve fragmentation by 12 to 20 percent over single-hole shots or simultaneous firing. All rock, 2000 to 23,000 pounds per shot, was screened and weighed to determine the fragmentation size-weight distribution.

Jan 1, 1991

By Q Liu, P D. Katsabanis

The energy output of crushed AN/FO, crushed AN/FO mixed with Aluminum (5%, 6.4% and 9.4% A1 by mass) and a commercial emulsion explosive has been measured using a detonation calorimeter. The charges had a diameter of 10 mm and were heavily confined by a 11 mm thick copper shell. In order to achieve stable detonation glass microballoons were used in the explosives so that the density of the AN/FO charges would be around 1.1 g/cc. The charges were detonated in vacuum and the detonation products were analyzed using gas chromatography. It was found that energy values were very close to calculated values obtained by ideal detonation codes.

Jan 1, 1993

By Tom Short, Paul Kunze

In this paper, the authors describe major changes in drilling and blasting methods instituted at the Zortman And Landusky Mining Company Properties to maintain the viability of these north central Montana surface mines in the present period of depressed precious metal prices. The authors explain how improved drilling procedures minimized problems due to uneven benches and floors. They also describe changes in explosives loading and delay blasting techniques which improved fragmentation, thus increasing metal recovery from heap leaching. Quantities were increased substantially and a new bulk explosives loading system was placed in service with a special down-the-hole bulk loading truck and storage facilities for bulk ANFO and bulk emulsion. At the same time, drill patterns were expanded by nearly 40%. The authors also describe a new technique of using explosives to selectively cast waste and ore in different directions so as to reduce the cost of separating the ore.

Jan 1, 1986