Search Documents

By Adrian Moore, Alan Richards, Andrew Brodbeck

Structural blast vibration limits should be based on the strength of the structure, the stress induced by blasting, and a responsible factor of safety. In this paper a methodology that uses direct strain measurements to determine the stress induced by blasting is described

Feb 1, 2020

By Raimo Vuolio

"Over the past 30 years, the Nordic countries have developed similar practices for estimating damage caused by rock blasting vibrations. However, over the last few years the risk of damage has sometimes been estimated by using international values, which have created unnecessary costs, since they are too conservative. This paper gives a proposal for Finnish blast vibration standards and a calculation model for the extent of the zones for building inspection, risk analysis, and vibration measurements. The international conclusion is that particle velocity is the best descriptor for limiting damage potential for structures. Over 900 000 vibration data recordings from 52971 blasts were collected for this paper during 1970-1989. They show that the most practical description is the vertical component of the peak particle velocity. As rock is a nonhomogeneous medium, it is hard to predict the need and scope of risk analyses, building inspection, and vibration measurements. As a large number of blasts were monitored for the recording of the peak particle velocity in several locations in Finland, and the data combined, it is possible to establish safe scaled distances for the calculation of the need and scope of risk analyses, building inspections, and vibration measurements."

Jan 1, 1991

By David Leidel, James Stuart

The 50 ohm resistorized electric detonator is commonly used in the oilfield for initiation of wireline conveyed perforating guns and other downhole explosive tools. This type of electric detonator provides some degree of safety above that of the conventional one ohm electric detonator, since a higher current level is required to initiate the device. In order to obtain the necessary data to develop safe distance tables from RF sources for the 50 ohm electric detonator, laboratory tests were conducted to determine the detonator’s “no-fire” current, AC impedance, and its susceptibility to ESD. The results were surprising as two types of failure modes were observed. The “no-fire’ current levels determined from Langlie “One-Shot” Test Methods were determined for the devices tested providing values for the 0.999 probability “no-fire” power level at a 95% confidence level. This data will serve as the basis for sets of safe distance tables from RF sources that will appear in the forthcoming edition of the Institute of Makers of Explosives Safety Library Publication 20, “Safety Guide for the Prevention of Radio Frequency Radiation Hazards in the Use of Commercial Electric Detonators, (Blasting Caps)”.

Jan 1, 2010

By Jeffrey W. Lin, Jonathan D. Abbott, Patrick R. Bowden, Tyson J. Plitt

Pentolite is a class of high explosives containing trinitrotoluene (TNT) and pentaerythritol tetranitrate (PETN) with PETN content typically ranging from 40 to 60 wt%. Manufacture involves melting TNT, 80 °C, followed by addition of PETN and trace ingredients to form a homogeneous mixture. Once a mix is ready to be poured, several factors can influence the behavior of the finished product including how long the mix has been at temperature and cooling rate. After the manufacturing process has been completed, storage conditions combined with manufacturing conditions may cause physical changes. Two such changes explored were exudation, liquid exuding from solid boosters, and ratchet growth, irreversible volumetric expansion. Exudation is principally caused by excess water in the process. Ratchet growth is a common phenomenon of nitroaromatic compounds such as TNT where time and temperature fluctuations can cause materials to increase volume, simultaneously decreasing density. Although neither phenomenon affects common attributes such as sensitivity, performance, and shelf-life, both can cause issues in storage and handling. In this study pentolite was cast into various forms under different manufacturing conditions and evaluated over several months of controlled storage conditions including ambient, temperature cycling and elevated isothermal. Subjective and objective measurements were made throughout the evaluation period with the aim to determine the preferred storage methodology.

Jan 21, 2025

By R J. Hill

Blasters are well aware of the problems and expense faced when trying to load in wet bore holes; problems of poor coupling and poor density, as well as the expense of higher priced cartridge product. In answer to these problems, I developed a system for dewatering using nozzles with lay -flat plastic liners which I have used successfully over the last few years. I found the system not only gave me better shots than I could have expected in the circumstances, but also dramatically decreased costs. The system has been adopted by two large roading contractors and a quarry operation in Eastern Canada.

Jan 1, 1986

By Jennifer P. Harrell, D. Joseph Hagerty

In many areas of the eastern United States, especially in the Midwest, past mining activities have left large and extensive underground openings. Now, renewed mining is occurring in such areas in surface pits. Also, construction blasting often occurs in rock over such old openings. Within the last fifteen years, some attention has been given to the interaction between surface blasting and underground cavities; concern has been expressed about the possible changes in vibrations transmitted through areas underlain by old mine workings (Siskind, Stachura and Nutting 1987). Previous studies also had indicated that underground openings could influence transmission of surface mine blast vibrations (see, for example, Woodward-Clyde Consultants 1977). The principal concern is that underground openings under surface blasting may intensify low-frequency vibrations. If such intensification occurs, use of available equations to predict peak particle velocities and to design blasting patterns and select blasting parameters could lead to possibly damaging ground shaking.

Jan 1, 2002

By Andrew Ritter, Victor I. Montenyohl, Stephen R. Winzer

Thirty-seven open pit production blasting operations have been monitored using high-speed cameras running between 500 and 7000 frames per second. Analysis of the resulting films reveals irregularities in timing including sequencing errors and crowding (holes firing less than 8 ms apart), confirming results of laboratory testing of ms delay blasting caps (Winzer, 1978). Where blasting parameters are otherwise constant and within recommended guidelines (stemming, spacing, burden, etc.), timing problems dominate the overall performance of the blasting operation. Model tests in layered Homalite 100, designed to simulate joint or bedding planes in rock, indicate the importance of the stress waves generated by the explosive in developing the crack network which is ultimately responsible for the fragmentation seen in the resulting muckpile. These mechanisms are strongly supported by high-speed film studies at Pinesburg, Maryland. Experiments in controlling relief in deep shots (where depth approaches the lateral extent of the bench blasted) using borehole geometry and hybrid initiation systems (electronic timer and pyrotechnic delays) were carried out. The results suggest that the 1 me/ft. of burden guideline developed by Bergmann et aI., 1974 is too short, and that much longer times are necessary to optimize fragmentation and muck digability. Longer times are found to reduce noise, vibration, and flyrock.

Jan 1, 1979

By Carlos Pañura, Michael Geldres, Alejandro Rojas

The vibration waves are produced by the detonation of the explosive charges of each blasthole, analyzing the vibration waves produced by each blasthole, allow us to determine the optimal time between the detonation of each blasthole to reduce the vibrations of the production shot. Once the optimal time is found, it is possible also, to predict the vibration of the production shot (considering times and sequences) using predictive models. The waveform recorded includes information regarding the particle velocity and the dominant frequencies of the vibration.

Feb 1, 2020

By R. Ranjan

Stanstead granite has been investigated with respect to its dynamic compressive strength and its strain-rate dependency. A standard Split-Hopkinson Pressure Bar (SHPB) apparatus has been employed to generate strain rates of up to ~500/s through high-velocity impact. The diameters of the test samples were 19 mm, and tested under impact velocities up to ~20m/s. It is found that even within this limited range of strain rates, the dynamic compressive strength for the granite showed nearly a 100% increase in value compared to those obtained under static loading conditions (e.g. compressive strength of 394 MPa at a strain-rate of 600/s, compared to 215 MPa obtained under static loading). The details of the test are described in terms of incident, reflected and transmitted stress pulses, along with means to achieve stress equilibrium in the test samples under dynamic loading conditions. The advantage and drawback of the use of ‘pulse shaping’ techniques to achieve dynamic stress equilibrium are also detailed.

Jan 1, 2010

By Bill Rose, Alan Foster

This paper will outline blasting as undertaken at the Flour Mill project in the Georgetown area of Washington, D.C. It will discuss the vibration and blasting problems found in blasting in high risk and highly populated areas, and the day to day methods used to minimize damage potential and still maintain adequate fragmentation.

Jan 1, 1979

By W Russell

The Hercudet Non-Electric Delay Blasting Cap System provides a means of achieving greater flexibility in the use of delays, using totally enclosed gas detonation circuits which eliminate the concussive effects of detonating cord trunklines in the confinement of access tunnels beneath pillars of ore. This is an account of one such pillar blast.

Jan 1, 1985

By Chapman Young, William L. Fourney, Richard D. Dick

During 1981 and 1982, an extensive oil shale fragmentation research program was conducted at the Anvil Points Mine near Rifle, Colorado. The primary goals were to investigate factors involved for adequate fragmentation of oil shale and to evaluate the feasibility of using the modified in situ retort (MIS) method for recovery of oil from oil shale.

Jan 1, 1985

By R W. Givens

This paper discusses emulsion performance and characteristics. Also presented are pattern design equations by a weight strength method, a "Q" factor method, and a coupled energy powder factor (CEPF) method. Pattern expansion by replacing ANFO with emulsion is presented along with quality control checks for emulsion products. The predicted performance of the calculated burden and the equivalent powder factor as a function of the emulsion percentage, as determined by the three methods, is compared. Field results indicate that of the three methods the weight strength is the moot conservative, the "Q" is overly optimistic, and the CEPF more accurately predicts the effect of coupling and is more consistent with a variety of emulsion and heavy ANFO products.

Jan 1, 1989

By Richard W. Watson, Julius Roth

The Bureau of Mines has recently completed a contract study of the hazards associated with surface mining.! Part of this effort involved an analysis of surface mining accidents associated with blasting activities. For this purpose, 71 reports of accidents investigated by the Bureau of Mines or the Mining Enforcement and Safety Administration (MESA), covering the period from 1962 to 1976, were collected and analyzed. In addition, blasting accident frequencies for the period 1973-1976 were extracted from the central computer files maintained by the Health and Safety Analysis Center (HSAC) in Denver, Colorado. This paper presents a preview of the findings, which are treated in more detail in the final report.

Jan 1, 1978

By David R. Holberg

In the Kansas City metropolitan area, mineable Bethany Falls Limestone occurs 80 ft below river level under the 700 acre Park College Campus on the north bank of the Missouri River at Parkville. For 20 years prior to this project various firms passed over this opportunity to mine this property for construction aggregate because of uncertain costs, financial risk, and the difficulty of constructing an entry tunnel. This paper describes the drill and blast construction, rock bolting, and shotcrete lining of a 750 ft. long, 15% declining grade, truck tunnel through several Pennsylvanian limestones and shales.

Jan 1, 1997

By T Weaver, R Dick, R Sivakumar, C T. Aimone

A series of small-scale crater tests were performed in concrete and sand in an effort to understand the cratering process in large-scale field blasts. The surface orientation of these tests varied from flat to a 30° slope. In comparison to previous crater experiments in competent oil shale, the crater tests in concrete produced craters similar to those in oil shale after scaling the measurements for differences in the mass of explosives among the experiments. Material strengths and the degree of brittleness had a significant effect on the size and shape of the crater. The small-scale sand tests resulted in some crater features that were similar to large explosive tests in alluvium and soil.

Jan 1, 1986

By C De La Cruz

The use of a thin-film piezoelectric stress gauge to determine the pressure profile in a detonating explosive has been demonstrated. These PVDF gauges have measured, in the borehole, the Chapman-Jouget pressure and the release adiabat of the detonation products for several explosives including ANFO and ANFO/emulsion mixtures. The technique can provide: (1) a direct measure of the blasting stimulus, (2) a sensitive QA tool for the blaster, and (3) a means to examine the magnitude and effects of preshock from adjacent bore holes. The PVDF pressure gauge is self powered, can measure pressure from a few bars to 400 kbars, has high time resolution (0.05 µsec), and is easy and economical to use.

Jan 1, 1997

By R E. Langston, S M. Gazioglu

A preconstruction inventory program was conducted to determine the existing conditions of residential, non-residential and all other structures within 2,000 feet of the blasting limits for a highway excavation site in Asheville, North Carolina. Prior to major production blasting, eleven test blasts were detonated to establish site specific propagation parameters in order to develop contours of maximum allowable explosive charge weights per delay. The method of scaling distance by the square root of charge weight per delay was utilized in developing the contours of allowable charge weights. The charge weight contours were revised during blasting operations as additional vibration data became available. The effects of blast induced vibrations on a nearby water storage reservoir, a nearby vehicular tunnel and other adjacent residential and non-residential structures were observed and monitored over a period of two years of blasting operations.

Jan 1, 1980

It has been common practice for many years to predict and control underwater blasting effects on the basis of certain simplified theories related to the pressures generated by underwater detonations. Unfortunately, two of the most commonly applied concepts in many instances do not provide an accurate modeling of typical field conditions nor the potential for damage. One of these concepts is that the damage potential is related directly to the peak pressure generated by an underwater detonation, without regard to the time history of the pressure pulse. This belief has led to the widespread use of air bubble curtains to reduce peak pressures, without considering the effect that air curtains have on the time history of the pressure pulse. At times, this procedure can be unwise. The other concept is based on the premise that pressure pulses in solids (such as rock) will always be transmitted to nearby water bodies in agreement with the theories of the transmission of plane waves across normal (perpendicular) boundaries. In reality, such conditions are quite rare.

Jan 1, 1985

By Ray Jambakhsh, John Okell, Frank Cook

"In early 1988, an experimental study was carried out at the Inco's McCreedy West Mine inLevack, Ontario. The objective was to develop blasting techniques which would allow themine to maintain production targets and reduce blast induced vibrations and overpressure.Due to its close proximity to the town of Levack (approximately 900 feet), particularconcern was expressed as to the vibration and overpressure resulting from the undergroundblasting operations."

Jan 1, 1993