Search Documents

By Michael W. Oakland

Weidlinger Associates was retained to evaluate the foundations supporting ten oil storage tanks at a tank farm on the east coast. The tanks were constructed over the site of a landfill which was underlain by deep organic deposits. The tanks were typically 48 ft. in height and ranged in diameter from 60 to 150 ft. The tanks were supported on both wood and steel pipe piles. After more than 35 years of service, an inspection found that up to 25 percent of the piles had separated from the mat foundation. The operations at the facility were temporarily stopped pending further investigation. Weidlinger developed comprehensive finite element models of the foundations for each tank and used random generators to conduct Monte Carlo simulations the range of scenarios of detached support conditions since it was not possible to survey all the piles below the tanks. To confirm the modeled performance and verify stability, each tank was also load tested using water with electronic instrumentation installed by Geo-Instruments. The instrumentation provided real time, web based monitoring during testing in areas which would otherwise be inaccessible during loading. Through inspection, complex modeling and sophisticated load testing, Weidlinger and Geo-Instruments were able to show that all but one of the tanks could safely be put back into service. This paper details the analysis, Monte Carlo simulations and instrumentation and load testing performed for this unique project.

Jan 1, 2009

By G. W. Plant

This paper describes the design philosophy and construction details of piles between 25m and 32m deep to support 160m high and 110m base diameter cooling rowers for a major power station. It is sited on deep expansive soil where a vast plantation of Eucalypts had been felled. The depressed water table is expected to rise, leading to swell of the soil and uplift forces on the piles. These forces, combined with the complex loading from the cooling towers, led to design tensile loads up to 20MN (2 000 tons) per pile. When competent stable material was present hand excavated underreams 3m in diameter were constructed for the piles sup-porting the shells. However, in some areas it was not possible to form an effective underream and an innovative solution was sought. This comprised unstressed dowels in the underlying sandstone which were formed by percussion drilling through void formers cast into the piles.

Jan 1, 2010

By Ed Kase

Cross-hole sonic logging (CSL) has become the universal standard, nondestructive testing (NDT) method used in evaluating the integrity of foundation structures to maintain quality assurance and quality control (QA/QC) of transportation facilities and infrastructures. Tomography, based on three-dimensional cross-hole sonic logging data processing technology, offers an improvement over the techniques currently used to characterize the interior structure of drilled shafts. The underlying concept for seismic tomography is based on the principle that acoustic waves propagate at different velocities through different types of material or the same material with different physical properties. Three-dimensional velocity tomographic images provide greater detail of the interior structure, making defects easier to classify with respect to size and location within the foundation structure. By accurately classifying these defects, an engineer has the information necessary to accurately assess whether these structures meet the applicable design requirements, allowing them to repair or replace inadequate foundation structures. The end result is that the foundation structures will meet the safety and service life requirements for their project. This paper will present applications of seismic tomography, illustrating how seismic imaging can provide accurate information regarding the integrity of foundation structures.

Jan 1, 2003

By C. O. Riggs

Geotechnical exploration in North America, in particular, exploration for deep foundations analyses, is currently and generally performed following the most basic sampling and insitu testing methods and techniques. Some would surely say that the state-of-practice severely lags the state-of-the-art. Probably more than 90% of all deep foundations, both driven piles and drilled piers, installed in North America are initially analyzed and designed, i. e. geotechnically, on the basis of either the soil penetration resistance obtained by performing the "Standard Penetration Test" (SPT), or from laboratory shear tests performed on samples obtained using 76-mm (3-in.) nominal diameter, thin wall, "Shelby tube" samplers. The use of design data obtained with other exploration methods and devices, such as bore hole pressure meters, flat plate dilatometers, even cone penetrometers, occur on the fringes of practice and often in conjunction with the use of the two simpler methods of analysis. This basic approach probably represents an attempt of the profession to use, as much as possible, common, easily understood and easily communicated procedures in all geologic environments. The characteristics of drill rigs with the required drilling and samplng tools vary somewhat from region to region in North America according to the physiography of the area of use, the types of exploration data required on a day-to-day basis, the philosophy of the engineers and geologists that use the exploration data and the financial resources of the drill rig owner. The physical capability of the exploration drill rig used on a project can have a significant effect on the quality of samples or insitu tests. The physical configuration and the quality of the drill and the drilling, sampling and testing tools not only provide the mechanical capability to obtain data but affect the attitude of the field exploration crew and the quality of work. This complete presentation is taken, for the most part, from a book in preparation for publication: "Geotechnical Exploration and Site Characterization" by C. Riggs, A. Hatheway and N. Schmidt. The book is scheduled for completion during 1987.

Jan 1, 2010

By Rajasekar Subbian, Jessica Oudhof

In the Netherlands pile foundation design is done using CPTs in accordance with EC7 national annexure. The capacity per tip level is calculated for every CPT followed by zonation to find the tip level per zone. The correlation factors are used to take into account the variability in ground across the zone and they depend upon the number CPTs within the zone. The CPTs and pile tip levels selection for zoning is an iterative process that can demand significant manual effort to produce an economical pile plan. This often leads to the use of conservative correlation factors in order to accelerate the design process. Thus, it has been automated in a tool with CPTs, pile location and loads, and capacities as input. The tool has also been employed in two case studies and the results are compared to the current design practise.

May 1, 2022

By Dalia. R. Mohamed, Hisham H. Hafez, Marawan M. Shahien

"Construction activities in major projects that involve deep excavations necessitate the use of vertical walls surrounding the construction site to play an important role as earth retention system. The walls are usually partially penetrating impervious walls which can increase the efficiency of the ground water control system that usually consists of number of partially penetrating wells. The analysis and design of such system requires 3D numerical simulation. The aim of this study is to develop simplified semi-empirical approach to analyze and design such system. The analyzed model is a single well in a square site that is surrounded by impervious walls along the perimeter of the site in an unconfined aquifer. The results of the parametric analysis are presented in this paper aiming to assess and understand the factors that influence dewatering in terms of ground water or drawdown profile surrounding the well. The parametric analysis is carried out using the 3D finite difference software. The parametric analysis comprises with more than 550 cases calculated. The study involved the parameters; well penetration depth, impervious wall penetration depth, size of the construction pit, coefficient of permeability, well yield and well location or distance between well center to impervious wall edge.IntroductionThe presence of groundwater in a site may have impact on the construction processes involved during the course of project construction, especially those projects that involve deep excavations. Deep excavations, especially in urban areas, require the construction of supported walls all around the site perimeter to ensure the stability of the excavation. In most of cases, the constructed walls are relatively impervious. Depending on the ground and site conditions, the walls are not penetrating all the way down through to the bottom of the aquifer and thus the walls are partially penetrating walls. The presence of ground water necessitates the lowering of the groundwater to levels below the bottom of the excavation to ensure working in dry. This paper focuses on groundwater control systems that consist of deep wells inside square areas enclosed by impervious walls partially penetrating unconfined aquifers. The wells are partially penetrating the aquifer, as well. There are many factors or parameters that are related to the configurations of the components of the system that may influence the drawdown of a well in such groundwater control system. This paper is a part of a comprehensive study that aims to development of a simple method for estimating the drawdown of dewatering system of the described configuration. In order to achieve such a major goal, a 3D finite difference model is developed for the problem in hand. A comprehensive parametric analysis was then carried out to investigate the influence of all the parameters on the drawdown of a deep well in such groundwater control system. This paper describes the problem, the model, the parametric analysis including the involved parameters. The paper, then, demonstrate the results of the analysis showing the influence of the studied parameters on the drawdown of a single well."

Jan 1, 2016

By George Moses K, Mahendran K

Grouting is performed in rock masses in order to increase its strength properties and also to reduce the seepage. In the design of underground structures such as tunnels or caverns located in weak rock masses, grouting plays an essential role. Grouting is a complex process demanding high degree of skill and knowledge in understanding of grout flow and requirements for certain geological conditions. This paper discusses the design process for grouting in rock masses adopted for a cavern project and the practical difficulties faced during the execution at site. The design parameters of grouting includes the injection pressure, grout material properties and stopping criteria. The paper also discusses the various tests performed at site to evaluate the efficacy of the grouting process which was initially defined based on the design and previous experiences. The final grouting scheme suiting to the present geological condition is arrived based on the test results. The practical difficulties faced during the execution and the measures taken to overcome these are discussed in detail. This work shows the importance of state of art in the development of a grouting process based on geological and hydrogeological conditions prevailing at site and can be helpful in grouting design for weak rock masses.

Nov 1, 2022

By Beim Jorge, Piscsalko George

"Verifying the quality of cast-in-place foundation applications, particularly those cast under slurry, is of course important, due to its great dependency on the methodology employed and on the practices of the site personnel. Due to the techniques used to install these elements, it is usually not possible to inspect the hole prior to grout or concrete placement, but there are several Non Destructive Test (NDT) methods available to assess the integrity of the completed foundation elements. This paper will compare several NDT methods with the Thermal Integrity Profiling (TIP) method for verifying the integrity in Continuous Flight Auger (CFA) piles and Bored Piles. The Thermal Integrity Profiling method will be described and some examples will be presented where TIP testing was used to confirm the structural integrity of CFA piles and Bored Piles.IntroductionThere are several Non Destructive Test (NDT) methods available for integrity testing of foundation elements. Each of those methods has advantages and disadvantages (White et al, 2008). Some methods test the integrity based on the reflections of a stress-wave generated by low or high-strain impact, while others require tubes to be installed prior to concrete pouring, and test the integrity between those tubes, or within a small proximity of them. The former methods (especially the low-strain) are faster and more cost-effective, but are not able to detect the quadrant where the damage is located. The latter methods are able to determine the quadrant, but do not test the region outside of the reinforcing cage, that is, they are not able to determine the concrete cover. The Thermal Integrity Profiling (TIP) NDT method overcomes the limitations of these other NDT methods.Overview of Shaft Integrity MethodsUntil now, the most widely used methods to test the integrity of Bored and CFA piles were the low-strain pile integrity testing and the cross-hole ultra-sonic testing. The low-strain method for integrity testing (PIT) involves attaching an accelerometer usually to the pile top (using a putty or wax) and striking the pile surface with a handheld hammer, which causes a compressive wave to enter the pile. This wave is totally reflected when it reaches the end of the pile or a major defect, and is partially reflected when it encounters any change in crosssection, or a change in the resistance or density of the pile material. These reflections arrive at the top at a time determined by the distance and wave speed, and causes a noticeable change in the signal detected by the accelerometer. The acceleration signal is normally converted to velocity by simple integration, and sometimes the force applied by the hammer is also measured. The velocity (and force) signals can be processed by the pulse-echo method (in the time domain) or by the transient response method (in the frequency domain)."

Jan 1, 2015

By Seiji Mizutani, Hirofumi Taguchi, Makoto Yoshida, Hidenori Takahashi, Naotoshi Shinkawa, Kazuo Konishi, Yoshiyuki Morikawa, Masaya Kawata

"The lattice-shaped cement treatment method has been used to improve the seismic performance of liquefied sandy soil in Japan. The efficacy of the method has been confirmed by the huge earthquake in Japan. In the present study, a new method to improve sandy ground by using the lattice-shaped cement treatment method is proposed as a liquefaction countermeasure. It is the floating-type and lattice-shaped cement treatment method, where cement treated soil is not fixed to an un-liquefiable stratum. In this method, a fixed-type structure such as treated soil should be formed at the side of the floating-type treated soil to reduce its lateral displacement. In the study, one-dimensional dynamic response analyses were firstly conducted to confirm the mechanism of the new method. Secondly, a series of centrifuge model tests were performed to demonstrate the effect in a proto-type scale's stress condition. The analyses and model tests confirmed the effect of liquefaction countermeasure of the new method.INTRODUCTIONLiquefaction induced by an earthquake generates sand boiling and ground settlement. Other problems have also been reported, including a decrease in bearing capacity and an increase in the horizontal earth pressure against retaining walls. To prevent these problems caused by liquefaction of the ground, various countermeasures have been proposed, such as cement deep mixing and high-pressure jet mixing methods. These methods have the big advantage of being applicable to ground that contains soil with a fine-grain fraction. Furthermore, the unnecessary displacement caused by the construction can be reduced. In Japan, a lattice-shaped cement-treatment method has frequently been used at many construction sites to prevent liquefaction, where cement-treated piles are intersected to form a lattice, as shown in Fig. 1. The lattice-shaped walls can reduce the shear stress generated by an earthquake, restricting the liquefaction at that location. However, the construction cost of the cement treatment is relatively high compared to other methods such as the sand compaction pile (SCP) method, and needs to be reduced. Therefore, decreasing the total volume of the cement treatment is necessary to reduce the construction cost."

Jan 1, 2015

By Jack Hayes

The design and construction of deep foundations involve many uncertainties. For the designer there are uncertainties regarding soil and ground water variability, regarding sampling and lab testing, regarding analytical techniques and regarding construction technique. The latter being the uncertainty over which the engineer has least control and which may have the greatest impact on capacity. Foundations with a high design factor of uncertainty can be very costly. Foundations designed with a high factor of uncertainty may have a low factor of safety, which can be even more costly.

Jan 1, 2000

By Sam X. Yao

In construction of drilled shafts under water, placing concrete in the shafts is technically demanding and involves complex construction logistics. Past construction experience has demonstrated that high quality concrete can be placed in drilled shafts under water with a proper concrete mix and proper placement techniques. However, a significant number of failures have occurred which have resulted in excessive cost overruns and delays. These problems may have occurred because proper underwater concrete construction techniques have not been widely disseminated within the industry. This is a technical area where competent design and sound construction planning can achieve a significant reduction in both risk and cost. This paper will discuss some key technical issues in the concrete mix design, concrete production and placement for the drilled shaft construction. The paper also describes two lesson-learned case histories from drilled shaft construction projects.

Jan 1, 2013

By E. W. Raabe

The paper discusses the increasing role of specialist grouting techniques to form water seals or cut-offs for deep basement construction. Raabe and Toth discuss the various grouting methods available for sealing applications and then concentrate on the use of Soilcrete Jet Grouting, a system particularly well suited to ground water control. The Soilcrete processes, suitable soil types and quality control methods are fully described, particularly with regard to the formation of cut-off walls and sealing slabs to prevent the progress of ground water or leachates. The authors have included case histories detailing their experience on designing and installing Soilcrete seals for various projects in West Germany. These include an underground rail project in Dortmund and a discharge structure for the Alz Canal at Burghausen.

Jan 1, 1989

By K. E. Darnell

Drilled pier foundations have long been a favored foundation type for heavily loaded structures. Drilled piers derive their load-bearing capacity from end-bearing, and/or sidewall friction. This type of foundation is used in many geologic settings, including those areas underlain by hard carbonate rock, such as limestones and dolomites. When properly designed and constructed, drilled piers provide high load-carrying capacity in both compression and uplift. However, carbonate rock is often subject to intense differential weathering resulting in the formation of an irregular bedrock surface, sinkholes and caves; consequently, the investigation for, and the design of, drilled pier foundations is often complex. Further, the construction may be difficult and costly. This paper discusses geotechnical investigative procedures which can be employed to develop foundation design criteria and reduce the frequency of changed conditions. Finally, state-of-the-art construction practices and quality control techniques are discussed.

Jan 1, 2010

By Les R. Chernauskas

Driven pipe piles are commonly used for near and offshore structures due to their omni-directional bending resistance, large surface area, and ease of installation. However, these piles typically cannot be driven deep enough to develop significant and sustained uplift capacity, and in some cases do not generate enough end-bearing resistance before being overstressed during driving. When driven closed-ended, their relatively light weight to cross-sectional ratio, and when driven open-ended their tendency to prematurely plug, are some installation short comings. Spin Fin® piles are traditional pipe piles fitted with flat, steel plates (?fins?) attached at a slight angle over the lower few feet of the pipe. Their design development dates back several decades for projects associated with harsh, limited weather window, offshore Alaskan oil field work. These projects required a pile type that could generate high and sustained capacity in both compression and tension, at relatively shallow depth. During pile driving, a relatively short, high capacity pile translates into more rapid installations with smaller and more efficient equipment. In this type of environment, where pile capacities are large, cyclic loading is typical, and relatively high pile movement is tolerable, the Spin Fin® pile is a superior solution. This paper describes the experience of using Spin Fin® piles on several recently completed Massachusetts Steam Ship Authority projects.

Jan 1, 2011

By Dan Brown

Deep foundation contracting for transportation projects in the United States has typically followed the design-bid-build model in which contractors bid on a specific work product according to relatively inflexible prescriptive specifications. With continuous flight auger piling and the many types of proprietary drilled displacement auger piling, there appear to be advantages to contracting this work according to a different model. This paper provides a discussion of the use of a performance specification for this work in which the contractor has greater freedom to choose the most appropriate foundation system and also greater responsibility for the performance of the completed foundation. With public agencies subject to open bidding, this type of contractual arrangement presents opportunities to encourage innovation. There are also challenges for implementation in public works projects, notably the selection of qualified contractors and the verification of performance requirements on production foundations.

Jan 1, 2006

By Adam Pickles, Duncan Nicholson, Richard E. Prust, Hoe C. Yeow

"Moorhouse is founded on what at the time of construction were the deepest base grouted piles ever installed in London, specifically designed to accommodate settlement from the proposed development of Crossrail. This paper describes design and construction issues associated with this project with special emphasis on the construction aspects of installing these piles in a heavily congested site in Central London.INTRODUCTIONConstruction of the deepest base grouted bored piles in a congested site in Central London in 2002 posed a number of design and construction problems. To add to the complication, the new structure's footprint is within the safeguarded zone of the proposed new cross London rail link, Crossrail. Therefore the piles were required to be designed to allow for the effects of construction of the proposed Crossrail's tunnels and a new station at Moorgate. The design and construction issues associated with this project are described in this paper and methods used to address such issues are presented.MOORHOUSE DEVELOPMENTThe new nineteen storey high Moorhouse building was commissioned by Moor House Limited Partnership and will form another new Central London landmark building by the British architect Foster and Partners. Two of the four facades feature complex geometry to fulfill the city's planning requirements. The building is a steel frame structure stabilised by a reinforced concrete core. Floor plates span between the core and the perimeter with two rows of internal columns.The complex geometry of the superstructure requires a diagonal ""bandolier"" to transfer floor loads to certain perimeter columns. Another salient feature of the superstructure is the ribs that are provided to act as sloping columns to carry the loads down to the foundations."

Jan 1, 2005

By William H. Walton, Clyde N. Baker Jr., Darren S. Diehm

"A 51-story concrete core and steel frame commercial office tower was recently constructed on the site of the former US Gypsum building in downtown Chicago, Illinois, USA The structure foundation reused several caissons from the demolished US Gypsum building supplemented with new belled caissons bearing on silty clay hardpan. Extensive in-situ pressuremeter testing was performed during the geotechnical investigation to determine allowable bearing capacity and better estimate building settlements. Problems during foundation construction along the south side of the building frame required remediation of two caissons. One caisson was supplemented with micropiles, while the second caisson was abandoned and replaced with a straight-shaft rock socketed caisson. To determine the effectiveness of the repairs, the building foundation settlements were monitored during construction.IntroductionIn 2001, The John Buck Company began development of a new office tower at the southeast corner of West Monroe Street and South Wacker Drive in Chicago, Illinois. The site was formerly occupied by the 18-story US Gypsum (USG) building. Mr. Clyde N. Baker, Jr. (Senior Principal at STS Consultants, Ltd .) served as the foundation engineer for USG which was completed in 1962. The building was founded on a forest of belled caissons bearing at elevation -56 Chicago City Datum (CCD). For reference, the ground surface at Upper Wacker Drive is approximately elevation +20 CCD. The bearing material was a hard silty clay, locally described as Chicago Hardpan. The foundation caissons were designed using an allowable bearing pressure of 16 ksf (766 kPa). In 1996, the USG superstructure was razed, and the three-level basement was converted to an underground parking ramp.South Wacker DevelopmentThe 51-story high-rise building was completed in 2005 with a structural height of 681 feet (208 m), and an internal space of more than 1,000,000 square feet (93 ,000 square meter). The typical floor size is 27, 700 square feet (2, 570 square meter). Renderings of the building are provided in Figures 1 and 2. The largest single tenant is the accounting firm of Deloitte & Touche, which occupies roughly 45% of the building space with over 3,000 employees."

Jan 1, 2005

By Georg Breitsprecher

The technique of Stabilising Columns (product names are for example "Stabilisierungssaulen" (STS) or "Coplan Stabilisierungs-verfahren" (CSV)) is gradually becoming well accepted for ground improvement. The installation, dimensioning and quality control are standardized by DGGT (German Association for Geotechnique), working committee 2.8, of which until now only part one exists for dry columns. This paper describes the installation and testing of stabilising columns for a ground improvement project. To achieve comparable results in testing both ready mixed concrete and dry binder had been used for production.

Jan 1, 2006

By Tracy Brettmann, Shailendra Endley, Jason Leary, Shashank Valluru

"Augered Cast-in-Place (ACIP) piles have long been used for deep foundation support in sands due to their high capacity and speed of installation. Very little information exists on the effects on capacity if the auger needs to be withdrawn from the hole prior to grouting. This condition can occur due to various reasons including grout plug ups, equipment issues, and grout supply delivery problems. It can become a major problem for the project team if this happens during production because the capacity of that pile is then in question, potentially resulting in re-design, installation of replacement piles and/or schedule delays. This paper compares the results of two high capacity test piles installed into a dense sand where one test pile was installed by first completely withdrawing the auger from the hole after drilling to the pile tip depth and the other test pile was installed utilizing conventional industry standard methods. Identical load tests were then performed on both piles to compare the effects of the two different installation procedures. The load test results were surprisingly similar in this case although the grout take required for the test pile installed in the pre-drilled hole was significantly higher to produce a similar grout return depth.IntroductionAugered Cast-in-Place (ACIP) piles are used extensively along the Texas Gulf Coast due to their combination of high capacity and speed of installation resulting in one of the most cost effective deep foundation systems relative to other options. Soil conditions in this region typically consist of alternating layers of sand and clay in the upper several hundred feet. ACIP piles are routinely installed to depths of over 100-ft to achieve the required capacity depending on the site specific soil conditions and therefore typically extend through and tip into sand layers. Occasionally, due to various reasons like equipment issues and plug-ups, the auger is withdrawn from the hole without grouting. Significant sand in the soil profile could lead to questions about the effect of the auger withdrawal on the pile capacity and load deflection relationship.This paper summarizes the results of two identical pile load tests performed on adjacent piles of the same length with the main difference being one was installed using the standard installation procedure and the other was installed by first completely withdrawing the auger from the hole after drilling to the pile tip depth. The load test results were then evaluated using load transfer analyses to estimate the effect of the withdrawal of the auger on the load-deflection characteristics and capacity."

Jan 1, 2017

By Florian König

It is well known that the bearing capacity and stiffness of displacement piles may increase significantly with time, a phenomenon usually referred to as set-up. In cohesive soils the set-up is commonly explained by consolidation processes in which the dissipation of the excess pore pressures around the pile leads to an increase in effective radial stresses. Recent case histories show that set-up may also occur in sand over a period which exceeds by far the consolidation process. Therefore, other effects apart from the dissipation of excess pore pressures must contribute to this long-term set-up effect. This paper presents the results of a series of multiple pile load tests on prefabricated concrete piles which capture the effect of pile set-up empirically. The main characteristics of the set-up trend are shown with respect to soil type, pile dimensions and distribution over the pile length. Possible reasons for pile set-up like consolidation and stress relaxation after the end of driving are examined using a finite element model which simulates the pile installation process.

Jan 1, 2006