Search Documents

By Ernest Naesgaard

Post-grouted micro-piles were used for the seismic upgrading of the Vancouver International Airport Domestic Terminal Building (DTB). The micro-piles provided vertical resistance to both uplift and compression loads to supplement the existing timber pile foundations ability to resist the earthquake induced forces, and to provide foundation support at locations where the installation of traditional driven piles was difficult. This paper describes the site conditions, design rationale, installation method and quality control testing procedures. Site and Subsurface Conditions Vancouver International Airport is located within the central portion of Sea Island, Richmond, British Columbia (Fig. 1). Sea Island is bordered by branches of the Fraser River on the northeast and south sides and the Strait of Georgia along the west side. The natural grade of the island is part of a large delta that has been built up over several thousand years. The general pattern of sediment deposition has followed the direction of the Fraser River flow from east to west, and has built up soft sediments of about 200 m thickness at Sea Island (Luternauer, et al. 1993, Mathews and Shepard 1962). The original grade in 1962 prior to the existing Airport Terminal Building development was at about geodetic elevation 1.1 m with a grass and topsoil cover.

Jan 1, 2004

By Pirooz Barar

The new Stanley Hall building will house the center for bio-engineering and technology research for the UC Berkeley campus. The structure is located at the northeast part of campus, adjacent to Donner Lab, on the west side of Galey Road, approximately 600 ft. from the Hayward Fault. The building site has a complex geological formation. To the east there are clayey soil shale formations, and to the west there is greywake shattered sandstone. The water table is at 10 ft. below grade. The structure will consist of 6 levels below grade and 8 levels above grade, which calls for an 83 ft. deep excavation on the northeast side. There is an approximately 35 ft. grade differential between the east and west sides of the building. Because of this severe grade differential, as well as high water tables, the lateral forces on the building due to uneven earth pressures would have been 2 times the magnitude of the seismic forces. To mitigate the lateral earth pressures, a permanent Soil Nailed Wall, integrated with the structural system of the building was designed. PB&A, Inc.?s in-house design program ?Winslope? was utilized to design the system and the data obtained from a rigorous monitoring program, were used to calibrate several computer runs using Plaxis program.

Jan 1, 2004

By William F. Loftus

When high capacity diameter pipe piles are driven open-ended into the underlying bedrock, the material gathered inside the pipe often must be excavated to allow concrete to be placed within, in a clean environment. This paper discusses a method of dealing with this ?to be excavated material - the contaminated soil of the Harlem River in New York City, USA.?

Jan 1, 1996

By Haijian Fan

Currently, deep foundation designs for the service limit state are deterministic in nature. The settlements and lateral deflections of deep foundations are calculated by means of numerical techniques whereby the foundation-soil interactions are characterized by discrete load transfer curves such as t-z or p-y curves. The noted deficiency of the deterministic approach is that the uncertainties arising from various sources, such as soil properties and model errors are not considered. To address this deficiency, a performance-based reliability design methodology is developed using Monte Carlo statistical methods. The performance based design criteria are defined in terms of the specified allowable displacement. The input to the numerical solution techniques, including the soil strength parameters, unit weight of the soil are relevant to the generation of the load transfer curves are treated as random field. The well established random field generator algorithm, local averaging subdivision, is used to generate random samples of input, where the mean values, variances, the probability distribution, and correlation structures are required statistical parameters for these random variables. The objective of the performance based reliability design is to determine the optimized foundation dimensions so that the probability of failure is less than the target probability of failure. The probability of failure by the Monte Carlo approach is simply the ratio of the number of unsatisfactory performance to the sample size. A numerical example for laterally loaded drilled shaft is given to illustrate the application of the methodology. The incorporation of the correlation length is shown to be critical for properly accounting for the site soil spatial variability.

Jan 1, 2017

By H. R. Masoumi

This paper presents a numerical model for the prediction of free field vibrations due to vibratory and impact driving. As the focus is on the response in the far field, where deformations are relatively small, a linear elastic constitutive behavior is assumed for the soil. The free field vibrations are calculated by means of a coupled FE-BE model using a subdomain formulation, proposed by Aubry and Clouteau (1992). The model is validated by means of the results of Kaynia and Kausel (1991) for the impedance of a single pile. First, the case of vibratory pile driving is considered, where the contributions of different types of waves are investigated for several penetration depths. The results show that in the near field, the response of the soil is dominated by a vertically polarized shear wave, whereas in the far field, Rayleigh waves dominate the ground vibration and body waves have been importantly attenuated. Second, the case of impact pile driving is considered. A linear wave equation model is used to estimate the impact force during the driving process. Furthermore, it is investigated how the soil stratification influences the ground vibration considering the case of a soft layer on a stiffer half space. The results show that when the penetration depth is smaller than the layer thickness, the layered medium has a small influence. However, when the penetration depth is larger than the layer thickness, these effects become more significant. Finally, the computed ground vibrations are compared with experimental data reported in the literature.

Jan 1, 2006

By Wolfgang G. Brunner

In the far north of Uttar Pradesh Province in the Indian Himalayas, the 280 MW Dhauliganga hydroelectric power plant is under construction by National Hydroelectric Power Corporation (NHPC), a state- owned enterprise, and a joint venture of Kajima Corporation of Tokyo and Daewoo Corporation of Seoul. This project sets out to develop the lower section of the mountain cascade of the Dhauliganga River, a tributary of the Sarda River, with a 311 m gross head. The 1360 km2 mountainous catchment area is bounded in the north- east by the Chinese border and in the south- east by the Nepalese border. The dam project is located in a remote area north of the principal town of Darchula of the upper Sarda valley, which is one of the seismically most active regions of India. The 56 m high rock fill dam, which will be the first of its kind in India, is faced with concrete and has a 1 m thick, at its crown 270 m long and over 70 m deep cut- off wall of plastic concrete below its toe. The cut- off wall, with a total area of 7500 m2, is constructed by a combination of Bauer hydraulic grabs, assisted by chisels and a Bauer BC 40 cutter which enables the overlapping joint system to be installed, guarantees optimum verticality and enables the cut- off to be keyed into the bedrock formation.

Jan 1, 2004

By James P. Hambleton, Sam A. Stanier

A perceived advantage of screw-type foundations is the ability infer aspects of foundation performance from quantities measured or observed during installation, especially the installation torque. A particular concept widely used in practice is to correlate installation torque to ultimate capacity. This notion has proven useful as a field verification technique despite the absence of validated models that relate key variables of interest, such as installation torque, axial (crowd) force, geometrical parameters, and soil strength. This paper considers previous work by the co-authors and collaborators on analytical, numerical, and physical modelling of screw piles to relate the quantities measured or controlled during installation (e.g., installation torque) to the ultimate capacity and soil strength. Attention is given to saturated clay as a particular soil type amenable to simplified analysis. An analytical model for a single-helix pile is considered as a means of directly relating the ultimate capacity and undrained shear strength to the installation torque, crowd force, plate pitch, plate diameter, shaft diameter, installation depth, and surface roughness. The connection between the installation variables and ultimate capacity—and the sensitivity to crowd force in particular, a quantity that is typically not measured during field installations—is also discussed. The theoretical predictions are compared against data obtained from small-scale laboratory experiments that suggest the installation torque relates to the remolded strength of the soil. INTRODUCTION Screw piles are deep foundations that are twisted into the ground through an applied torque. Advantages over driven piles or drilled foundations include the relative silence of the installation, with low ground vibrations, and the possibility of being easily decommissioned by reversing the direction of twisting. Screw piles are now routinely encountered as a flexible, low-cost solution for numerous applications (Figs. 1 and 2), and they are also being considered for applications in offshore energy production due to limitations being imposed with respect to decommissioning and underwater noise. Also known as “screw anchors,” “helical piles”, or “helical anchors,” screw piles consist of helices or helical plate elements attached to a central shaft. Figure 3a shows the components of a single-helix pile and key variables. The diameters of the shaft and helix are denoted by d and D, respectively, and p is the pitch of the helix. Variable H denotes depth of the helical plate, and T and N denote the torque and axial (crowd) force applied during installation. In typical applications, the pile includes multiple helical plates, and the shaft is composed of segments that allow for it to extend to large depths into the soil.

Jan 1, 2019

By Peter Faust

"The south access road to San Francisco’s Golden Gate Bridge, known as Doyle Drive or Presidio Parkway, needs to be replaced. Built in 1936, it is the primary highway and transit linkage through San Francisco between counties to the north and south. The roadway is tucked into the natural contours of the Presidio and the Golden Gate National Recreation Area, one of the nation’s largest urban parks.The old steel truss structure will be replaced by a new concrete cast-in-place bridge. The foundation design of the new bridge is based on drilled mono shafts below each bridge column. Most shafts required large diameter permanent steel casing installed under strict vibration limitations since several historic landmarks are near the project alignment. Malcolm Drilling decided to use the largest oscillator in the world to install the piles.The area occupied by the Presidio is generally hilly, sloping down northwards to San Francisco Bay. In the western half of the project route, two bluffs rise steeply to about 80 ft (25 m). The bluffs are separated by a valley 60 ft (18 m) deep and 1,500 ft (457 m) wide, which is spanned by the old and new bridge. Overburden soils in this valley are made up of artificial fill, slope debris, ravine fill and Colma Formation, a fine to medium-grained sand unit with clay beds. The Bay Muds encountered in the project area are typically soft clayey silts, becoming medium stiff with depth.The basement rocks underlying the overburden belong to the Franciscan Formation, described as shale, sandstone, serpentine and greywacke, it is extremely variable in hardness, fracturing and weathering. The material can vary from very hard to very soft, can be slightly to very intensely fractured and almost not weathered, to totally decomposed within relatively short distances both laterally and vertically. Rock strength can vary from too weak to be tested to serpentine layers with unconfined compressive strength of 15,000 psi (103MPa) or higher. Groundwater levels in the area are typically no more than 10 to 20 ft (3 to 6 m) below the ground surface."

Jan 1, 2012

By Dennis Nottingham

The need for deep compaction of submerged granular soils has led to improvements in this area. In 1971, L.B. Foster Company personnel patented a method of deep compaction using a vibratory pile hammer and pile probe. The technique had some success, but did not produce consistent results and thus found its way to obscurity. Other patents attempted to modify the technique by various probe modifications, but again without measurable improvement from a practical point of view. Solutions to economical deep compaction up to 100 foot depths particularly in saturated granular soils would have a great impact on the construction industry and new bulkhead structures being developed, thus PND was prompted into related research and development. The advent of higher horsepower vibratory hammers, coupled with PND engineers? experiments, observations and measurements, led to an ?H? pile probe design which has produced measured soil density improvements up to 250% using SPT ?N60? values as a measure.

Jan 1, 2013

By G. L. Sivakumar Babu, P. Chaithra

"Raft foundations which are used against differential settlements and for carrying heavy loads can still be subjected to excessive settlements even if it is safe against bearing capacity consideration. Providing additional piles under the raft can reduce such settlements to acceptable values. In addition to settlements, the piles also relieve the raft a part of the total load and thus the bearing capacity of the Combined piled raft foundation (CPRF) is improved. Parametric study of response of piled raft foundation has been conducted and the results have been presented. The study is conducted using finite element based software, PLAXIS 2D. The main objective of the paper is to evaluate the parameters that affect the performance of piled raft for an economical and effective design. It has been shown that piled rafts are an economical solution in foundation design compared to raft foundation, for the soil conditions considered in the paper.1. INTRODUCTIONThe aim during the design and construction process of high-rise building foundations in urban areas is to ensure the lifelong safety and serviceability of the new and existing buildings in the neighborhood. In order to realize this aim in a cost-optimized manner, the combined pile raft foundation (CPRF) was developed (Katzenbach et al., 2005). For the foundation of high rise buildings with good subsoil, the simplest structure considered is a raft. But when the subsoil near the ground surface has low load-bearing capacity, high-rise structures are often rested on piled foundations.A piled raft and pile group serves similar purposes, but there are essential differences between them. A pile group is a set of piles that have a pile cap. The piles would be designed to share the pile load at ultimate state. The pile cap would be designed to link the piles together but the contribution of the pile cap to bearing capacity will not be included in the design. On the other hand, a piled raft is a foundation, wherein piles are provided along with the raft so that the total load acting is shared partly by the raft and partly by piles, rather than being dominated by the piles (as in a pile group). Piled raft foundations utilize pile support for control of settlements with piles providing most of the stiffness at serviceability loads, and the raft element providing additional capacity at ultimate loading (Poulos, et al., 2011). Therefore, piles are included in a foundation for two main design purposes: to provide adequate bearing capacity and to bring down the settlements to an acceptable level."

Jan 1, 2015

By Frank Rausche

The more widespread use of Augered Cast-in-Place (ACIP) Piles has generated increased demand for improved quality control measures. These deep foundation elements are often relatively long and slender and their structural quality depends on the experience of the installers, the adequacy of their drilling and pumping equipment, and of course, the properties of the soil. Since the concrete of ACIP piles is pumped under pressure into the borehole, the piles may achieve a very high unit shaft resistance if conditions are favorable and the piles are well constructed. Three types of methods can help assure that the piles are properly executed. During construction, monitoring the volume of concrete pumped and the pressure applied helps avoid structural defects. After installation, and once the concrete has hardened, the Pulse Echo Method allows for a check of the structural integrity of the shaft. Finally, a load test, performed some time after installation, yields a check of both bearing capacity and structural integrity of an individual pile. Because of their expense and associated construction delays, static load tests are normally done for only a few piles. However, at large construction sites, it may be necessary to perform many load tests either as a planned construction control activity or as a means of spot checking or verifying suspect piles. For smaller sites, however, static load testing may be prohibitively expensive. In such situations, dynamic load testing, originally developed for driven piles, has frequently been employed for drilled shafts and ACIP piles. In the latter case special consideration must be given to the ACIP pile slenderness and their often relatively low concrete design strength, which may not tolerate high dynamic loading stresses even though their unit resistance along the shaft is relatively high. Lately, the dynamic load test has become more feasible with the availability of loading systems that are custom tailored to this particular pile type. These systems produce a low velocity, low stress and high energy impact. Recent developments have also made the instrumentation process simpler: force measurements are now made on the ram rather than on the pile for increased reliability and simplicity. This presentation describes the requirements for successful dynamic load testing of auger cast piles and summarizes results from several projects where the new loading system and newly developed instrumentation was employed. A few cases are presented correlating static load test results with dynamic predictions, calculated by CAPWAP®.

Jan 1, 2001

By Thomas Kennedy, Michael Bennett

"History never repeats itself, but it often rhymes." The old aphorism reflects how the study of the past may, perhaps, be most widely valued when it can be used to improve current and future decision making. The education the authors received as geotechnical graduate students certainly impressed upon them the importance of recognizing that not all wisdom is necessarily new. Much of their graduate coursework involved reading technical papers that had introduced concepts of outstanding historical significance in the field, such as pore pressure coefficients, stress paths, and the stress history and nor- malized soil engineering model. These papers gave the authors both respect for and interest in the historical develop- ment of the field. After graduation, the authors furthered and deepened this interest by continuing to expand their knowledge of the profession through both experience in practice and the review of additional literature.

Jan 1, 2023

By Adrian M. Keller

Borehole televiewers are downhole inspection devices available for high-resolution imaging of a borehole wall following rock coring. Borehole televiewers should be considered by geotechnical engineers and geologists as a supplemental way of investigating rock for deep foundations. The optical televiewer (OTV) produces a digital optical image and the acoustic televiewer (ATV) utilizes reflected acoustic waves to produce images of the borehole walls. These devices can be utilized to examine soft or fractured zones in the rock mass, solution features, open joints or other voids not observable from traditional rock coring techniques. These devices along with computer post-processing can determine the strike and dip of joints, bedding planes, shear surfaces, or other structural features, eliminating the need for expensive oriented cores or manned downhole logging. An acoustic televiewer was utilized in the Fall of 2008 during the investigation phase for the I-70 New Mississippi River Bridge (I-70 MRB) in St. Louis, Missouri. Voids and fractures in the upper portion of the rock were described by prior consultants. Further investigation of these features was necessary to evaluate deep foundation options to support the main towers. Ten borings were drilled from a barge in the river at the two main tower pier locations. An ATV was utilized in each of the ten borings to produce images of the rock mass in the borehole and allow further investigation of the voids. Voids interpreted as solution features were readily identified in the ATV logs in multiple borings and at similar elevations, suggesting connectivity. Measurements of the voids? width, location in the borehole and orientation allowed a more thorough understanding of the potential impact the solution features may have on the planned deep foundations. An extensive grouting program was eliminated based on the ATV results.

Jan 1, 2010

By Peter Smith

One New Change is a landmark retail / commercial development in the City of London. Integral to the structure is the three double storey basement from which the building is serviced. The building construction involved a ?top down? (up down) construction technique to give programme benefits. In addition, the planning authority stipulated that 10% of the energy demand had to be met by Renewable technology. Cementation Skanska has not only delivered the foundation package - comprising secant piling and foundation bearing piles including Cemloc® plunged columns - but, alongside subcontractor Geothermal International, also installed a 1.7MW ground source heating and cooling system using Energy Piles® and open?loop wells to provide the renewable energy. The works were successfully installed and completed within a tight programme, and within the logistical constraints imposed by an inner-city location, concurrent demolition works and multi contractor involvement in the basement construction.

Jan 1, 2010

By Terence P. Holman

Micropiles are employed to retrofit existing foundations, including underpinning prior to future construction operations and resupport of existing structures that have experienced distortion and settlement. This paper presents analyses of the two case histories requiring the use of micropiles in these applications. The first case history involves micropiles used to resupport a settled pump station next to an excavation which had suffered basal failure and ground loss. A compression load test pile experienced plunging failure which, after analysis of the strain-gauge data acquired during the test, was attributable to a greater degree of disturbance to the subsoils beneath the site than anticipated. After construction of the micropiles around the pump chamber a synchronized jacking system was used to lift and right the 320 kip chamber structure, followed by resupporting it on the newly constructed piles. The second case history entails the use of micropiles for direct underpinning support of existing columns prior to a utility tunnel installation within an existing high-bay warehouse structure. The design constraint that most significantly affected the successful completion of this project was the desire to bond the new piles into the existing reinforced concrete foundations. As a result of the coring method through the footing, the ultimate bond stress measured during a pullout test was more than twice that assumed in the design. Monitoring of the underpinned columns during trench excavation indicated that the system performance was acceptable. These case histories reinforce the concept that lower capacity micropiles can provide a rapid means to underpin and retrofit existing structures.

Jan 1, 2007

By Terence P. Holman

Instrumented load testing of high capacity micropiles, followed by detailed analysis and numerical modeling, provided an opportunity for real foundation performance to be incorporated into the design of a complex urban high-rise structure. This paper discusses a design-based load testing program and subsequent analysis for micropiles incorporated into a piled raft foundation beneath a portion of a high-rise residential structure in Brooklyn, New York. Preliminary numerical analysis, performed using the commercial finite element package PLAXIS 3D Foundation, indicated that soil stiffening and transferring heavy core loads to greater depths was required to minimize the total and differential settlements. High capacity micropiles were modeled below the tower core mat to create a piled raft effect, reducing the settlements to acceptable levels. Final design of the foundation and micropiles, and final numerical analysis of the proposed foundation system required an instrumented load testing program to provide the Owner and design team with a level of comfort. The instrumented load test provided data on the evolution of load transfer, including the mobilization of significant tip resistance, frequently ignored in design, and micropile axial stiffness. Final numerical analysis of the foundation system involved refining the PLAXIS model based on the micropile behavior and load transfer mechanism observed during the load test program. The authors believe that the combination of design-based load testing and numerical analysis in this project yielded a more refined foundation system with realistic expectations of performance.

Jan 1, 2007

By Saba Mohan

This study presents results based on the Pile Installation Demonstration Project (PIDP) that was conducted as a part of the East Span San Francisco-Oakland Bay Bridge Seismic Safety Project. For the three full-scale pile installations, two different high-energy hydraulic hammers were selected for the installation. However, these hammers may not have sufficient energy to drive these large diameter piles at their ultimate capacity following long-term set-up. Nevertheless, these hammers were selected because, soil plug behavior, the generation of excess pore pressures and remolding of soil during driving were expected to reduce the shaft and end bearing resistance, and therefore reduce the energy required to drive these piles to design penetration. Data collected during continuous installation driving and after a series of re-strikes at different set-up times ranging from 1 to 33 days were used as input data for CAPWAP. These results were used to estimate the soil resistance along the pile length and at the toe of the pile, and the soil pile set-up behavior. Validity of the procedures used to predict the soil resistance to driving and predicted blow counts were verified with the field observed blow counts and the energy that was delivered to the pile. Based on combined CAPWAP analyses, the soil pile set-up with time was estimated and compared with results of other methods currently available in the literature for predicting the soil pile set-up rate.

Jan 1, 2002

By V. Tang

In this paper, Chinese economic situation are estimated and prospective developments predicted to assist those US firms who have been trying to do business in China, or are considering to pursue the China market.

Jan 1, 2010

By Ana Pereira, Naomi Norris, Donald Bruggers

The city of Christchurch, New Zealand is predominantly founded on alluvial sediments consisting of interbedded layers of loose to medium dense sand, soft to stiff silt and clay mixtures, and pockets of organics. These soil deposits have high liquefaction potential. Following the 2010/2011 Canterbury Earthquake Sequence several ground improvement trials were undertaken within Christchurch to understand the effectiveness of different types of ground improvement in these silty sand geological conditions. This paper presents a discussion of a stone column ground improvement trial undertaken at a Christchurch site with high fines content soils. Stone columns were installed using two types of installation methods and a range of Area Replacement Ratios (ARR) to assess the effectiveness of these ground improvement methods in high fines content soils as well as the influence on the type of installation method. Pre- and post-column installation CPTs, seismic Dilatometer Tests (sDMTs), cross-hole shear wave velocity tests, and plate load tests have been undertaken to assess the effectiveness of the ground improvement. Results of the testing are presented in this paper. INTRODUCTION This paper presents the results of a stone column ground improvement trial undertaken in Christchurch, New Zealand (Fig.1). In 2010 and 2011, four large earthquakes (greater than magnitude 5.9) and thousands of smaller aftershocks occurred in the greater Christchurch region. These events are referred to as the Canterbury Earthquake Sequence (CES). Liquefaction occurred across large portions of the city during the stronger earthquakes, particularly the February 2011 event. Following the CES a large amount of data was collected across the city including the location and volume of sand boils, and the location and magnitude of ground cracks. Additionally, data from thousands of ground investigations have been uploaded into a public database. As a result, there is clear evidence that silt and silty sands liquefy in addition clean sands. The CES and resulting liquefaction motivated a series of studies and trials from different organisations aiming to better understand the available technologies for liquefaction mitigation. The subject of this paper is a ground improvement trial undertaken by a local contractor specialising in deep foundations and ground improvement. They were interested in understanding the effectiveness of stone column ground improvement in high fines content (silty) soils using two different installation techniques, vibratory and non-vibratory. Different arrays and Area Replacement Ratios (ARRs) were used for each of the two methods of columns installation.

Jan 1, 2019

By Masakazu Takano, Koji Suzuki, Naotoshi Shinkawa

"Cement deep mixing (CDM) method successfully applied to a marine construction project in northern Vietnam is reported. The method is classified as wet method, in which cement slurry is injected into the ground. Thickness of clayey deposit subjected to improvement is from 20 m to 28 m, and the total volume of CDM improvement exceeds 460,000 m3. This is the first massive application of CDM method in the region. Three CDM barges, each equipped with four mixing shafts, were brought to the site in order to finish CDM work within a period of seven months. Cement content used in the work was 180 kg/m3 and water-cement ratio of slurry was 100%. Unconfined compression strength of stabilized soil was 1,200 kPa to 1,600 kPa in average with coefficient of variation from 0.3 to 0.4. Statistics analysis of the strength with these values gave percentage of lower strength less than 10%. Trial use of needle penetration test performed to study strength profile of a CDM column is also reported.INTRODUCTIONThe site of Lack Huyen Port Infrastructure Construction Project is located in the sea adjacent to Cat Hai Island, offshore Hai Phong city which is around 100 km east of Hanoi, the capital of Vietnam. Left side of Fig. 1 shows the location of the site. The project contains development of container terminal, dredging of waterway, construction of sand protection dyke to prevent waterway from being buried, and bridge construction to connect the island to the mainland.Joint venture of Penta Ocean Construction and Toa Corporation was awarded Package 6 of the project, in which reclamation of container terminal area, retaining wall construction and terminal road construction were included. Plan of the site is presented in right side of Fig. 1. The site work has been started in June 2013 and is scheduled to finish within 4 years."

Jan 1, 2015