Search Documents

By Gisele R. Passalacqua, Taylor Malangone, Subhash Mahali

New York City is a busy metropolis with 8 million people. New York has the largest public transportation system with 6 million riders a day throughout the subway system. Keeping this infrastructure in service is vital to the overall economy of the region. Hurricane Sandy proved to have a devastating impact on infrastructure in Metropolitan New York. New York City Transit is on the forefront to provide resiliency and maintain its facilities with the use of flood protection systems. This paper presents flood protection structures utilized at Hammels Wye substation site in Far Rockaway, Queens, New York. The site is in close proximity and surrounded by water. The subsurface conditions consist of loose silts overlain by medium dense glacial sand. The high groundwater level combined with limited access to the site presented challenges. A flood protection system consisting of flood walls was recommended for this site. In certain areas the flood walls consisted of retaining walls supported on micropiles. For other areas, the flood walls consisted of steel sheet piles with jet grout columns to reduce seepage below the walls. The effect of driving sheet piles with vibratory hammers on nearby existing structures is always a concern. Recently, hydraulic hammers with variable moment/frequency are being considered as a mean to reduce vibration effects during driving. In this project, an instrumentation testing program was performed to measure peak particle velocity during sheet pile driving utilizing the variable moment vibratory hammer. Plots of peak particle velocity versus frequency were generated. This paper will present the design aspects of the flood walls and construction challenges during installation. This will prove beneficial to engineers in both design and construction fields.

Sep 8, 2021

By Martin Mcdermott, Kevin Tehansky, Robert Ross, Jeffrey Goodwin

A foundation value engineering redesign is a collaboration between the project owner, original design team, general contractor, foundation contractor and redesign team. Without the acceptance and collaborative effort of all the stakeholders, the redesign process is doomed to failure. For the addition at the Hackensack (New Jersey) University Medical Center (HUMC) we had just such a collaborative effort for the drilled shaft redesign. For a successful redesign effort, the collaboration between the foundation contractor and their redesign team needs to fully exploit the contractor’s specific equipment and experience and convey how to apply this to the project as a whole to ensure everyone is confident that the project design goals are being met. For the HUMC project, applied load testing of the drilled shafts (bi-directional and lateral) were used to provide ultimate geotechnical design values for the redesign effort. By utilizing the contractor’s preferred equipment and the redesign team’s testing and application expertise, the redesign collaboration was able to enhance a good design and make it into a great project.

By Davide Grassi, Joel Joaquin Cortez, Giovanni Spagnoli, Nick Chittenden

Grouting is a technique used to improve the engineering properties of soils and rocks. Grouting techniques are classified under different criteria: injection method used, type of grout material injected, typical application, and the sequence of construction. The best-known criterion is the mode of entrance or admission of grout into the soil or rock. It is possible to identify therefore several grouting techniques: compaction, fracture, jet/mixing and permeation. The function of penetration grouting is to reduce the permeability of the soil or rock and/or increase the strength and density. In order to avoid displacement, permeation grouting shall be carried out at carefully controlled pressures and flow rates, using appropriate grouts. Colloidal silica is an innovative binder which has low viscosity (about 5 m·Pas), it is not toxic (pH lower than 9) and it is workable between +5°C and +45°C. This paper presents several case histories: a consolidation job related to the installation of a new sewer in North Italy in cohesionless soils, water stopping injection in a weathered granitic bedrock in California, permeation works in the US in sandy soils to improve excavation and the installation of sheet piles in the UAE. Results show that the colloidal silica an innovative and robust technology to perform grouting in very fine soils where conventional binders or micro-fine cements cannot penetrate.

May 1, 2022

By Stefan Swartling, Rudy Lyon, Donald A. Bruce

"Since their first production application in Sweden in 1995, water-powered, down-thehole hammers (WDTH) have been used throughout the world in many different drilling applications, total lines, over 25 million lineal meters of drill hole. This paper reviews the history and principles of down-the-hole drilling (DTH) in general with both air and water, before focusing on the details of WDTH hammers. A summary of the numerous and considerable advantages of WDTH drilling is provided, with particular emphasis on their superior productivity, smaller deviation, applicability in sensitive/urban conditions, environmental protection and much reduced energy requirements.HISTORICAL PERSPECTIVE ON PRODUCTION DRILLING METHODSAir-flushed drilling with top hammers began in the mining industry in Sweden in 1873, while down-the-hole (DTH) drills, again with air flush (and activation) became operational in 1950. During that same time interval, Simon Ingersoll had patented the first steam-powered, top hammer rock drill to provide higher productivity in blast hole drilling. It is well known that water, as an activating, flushing and cooling medium, has many significant advantages over the use of air. However, it was not until 1973 that top hammer systems (either air or hydraulically activated) for larger rigs were adapted to the use of water flush, typically via “under the head” swivels.The concept of a water-powered, down-the-hammer (WDTH) had been explored prior to G. Drill acquiring the original patent from Atlas Copco in 1988. LKAB, a huge underground mining company owned by the Swedish Government and providing about 90% of the European Union’s iron ore, purchased G. Drill in 1991 and encouraged the commercial development of the WDTH. The first full-scale WDTH production works were carried out for LKAB in 1995, since when over 25 million lineal meters of drilling have been recorded in both underground and surface applications.In 2001, G-Drill was renamed Wassara, which today still holds the worldwide patents for WDTH technology. Regarding North American usage, the first significant application was by Advanced Construction Techniques (ACT) Ltd. during the test grouting program conducted for the U.S. Army Corps of Engineers at McCook Reservoir, Chicago, in 2002. Since then, WDTH has become the tool of choice for specialty drilling and grouting contractors on dams and other major structures throughout the U.S."

Jan 1, 2015

By M. D. Riegel, P. B. Pizzimenti, E. M. Zamiskie, Britain A. Materek

"The Skanska/Kiewit/ECCO III team (SKE) in association with HNTB was awarded the design-build contract for Phase I of the Kosciuszko Bridge Replacement Project. As lead designer for the SKE team, HNTB was responsible for the design of the Brooklyn Connector which includes construction of approximately 2000 feet of new staged earth-filled embankments utilizing prefabricated modular retaining walls (T-Walls®). The proposed embankments will be constructed adjacent to and beneath the existing Brooklyn Queens Expressway (BQE) viaduct while the existing viaduct remains in service. Critical aspects of the settlement assessment relating to the soils supporting the existing BQE will be addressed, as their behavior drives the deformation of the viaduct. Furthermore, a construction monitoring program was used to enable the designer to assess settlement predictions and allow SKE to mitigate potential impacts to the existing BQE during construction. Additionally, the methodology for installation of the embankments in a limited access area underneath an active viaduct supported on settlement sensitive shallow foundations will be presented.INTRODUCTIONSkanska-Kiewit-ECCO III Joint Venture, in association with HNTB was contracted by the New York State Department of Transportation (NYSDOT) to design and construct the Phase 1 replacement of the Kosciuszko Bridge Design-Build Project. Phase 1 of the project involves the design and construction of the new eastbound structures of Interstate 278 over Newtown Creek from Brooklyn to Queens. The project runs between Morgan Avenue in Brooklyn and the Long Island Expressway Interchange in Queens (approx. 1.1 miles) and includes the staged demolition of the existing structures."

Jan 1, 2016

By Adnan A. Malik, Tadashi Maejima, Jiro Kuwano, Shinya Tachibana

"The helical piling system provides solution to many geotechnical related problems due to its quick installation, higher compressive and pullout resistance, no wastage of material, workable in limited areas and reusability. However, its use as a foundation for bridges and high-rise buildings is still limited as compared to other piling methods. In the present study, the performance and load settlement behavior of screw and straight pile is investigated under cyclic compressive load in dense ground conditions. To achieve the set objectives, pile load tests were conducted in a cylindrical steel container. The model ground was compacted with dry sand at relative density of 80%. It is observed from the test results that screw and straight pile resistance reduced when the cyclic load is applied at allowable pile resistance state. The reduction in the ultimate pile capacity is more in straight pile than in screw pile. However, straight pile showed higher ultimate pile capacity than screw pile under similar pile tip diameter. The effect of helix bending deflection on load settlement behavior and ultimate pile capacity increases under cyclic loading.INTRODUCTIONScrew pile is one of the new developments in deep foundation, which is growing tremendously fast because of its quick installation technique, less noisy operation, no wastage of material and involvement of minimum manpower. Screw piles have an edge on straight pipe piles due to its high bearing capacity and uplift resistance. The installation mechanism of screw pile is different from straight pile. Torque and pressure is required to install the screw pile whereas hammering, pressure and vibration is required to install straight pile. As the installation mechanism is different between screw and straight pile, therefore, the ground disturbance that is produced during their installation is also different. The ground disturbance produced during the installation also depends upon the pile tip condition i.e. open or closed ended. Sakr, (2009) stated that the compressive capacity of screw pile in 3 to 5 times higher than driven piles having the same shaft diameter and length. The reason for this increase in pile capacity is due to helix, which is generally 2 to 2.5 times the pile shaft diameter. Larger helices can give higher end bearing capacity but it requires very powerful machinery to install in dense grounds. For instance, if large helix screw pile is installed in a dense ground then helix-bending deflection will start affecting the end bearing capacity (Yttrup and Abramsson, 2003; Malik et al. 2013 and 2015). According to Malik (2015), the equations of thin plate (Young and Budynas, 2002) with uniformly distributed load on the plate can give reasonable estimation of helix deflection due to dense ground conditions."

Jan 1, 2016

By Andreas Brandner, Karl Schoenherr-Strasse, I. B. Brandner, Dipl. Ing

"A world famous Wintersport resort in the Alpine planned to build a parking garage for more than 600 cars and busses situated between a torrent, a district road and the village.A nearly 200 m long building giving place for 6 parking levels and a maintenance level for busses and trucks is situated alongside a hill causing excavation height between 20 and 25 meters, which had to be secured. Due to restrictions – neighbours did not allow the client to drill anchors for retention – we designed a solution combining micropiles, strand anchors, shotcrete and nails as permanent earth retention not exceeding the space of 7 meters provided by the local street. Soil conditions were as challenging - reaching from backfill to moraine with boulders of more than 20 m³ volume – as the construction period of total 12 months for the whole project, which was opened mid of November 2015.The innovative solution outperformed the client´s project from the technical and commercial aspect and helped the contractor to save time and money.The design process with its difficulties as well as erection process is described in the following paper."

Jan 1, 2016

By Abdulazeez Rotimi, Barry Sheppard, Abid Adekunte

Good engineering practice is a function of sound theoretical knowledge, first-hand experience on previous projects of similar scope and scale, good acquaintance with case histories of similar projects completed by others in similar environmental conditions, as well as satisfactory degree of exposure to state-of-the-art methodologies. The four factors itemised above are typically interdependent. They amalgamatively influence the judgement of the Engineer and they ultimately result in the delivery of safe and cost-effective solutions by Professional Engineers. This technical paper presents detailed information on the ground engineering aspects of a large-scale housing development project located on a sloping site that had been presumed to be unstable in West Sussex, England. The ground engineering design package for the scheme comprised of temporary working platform designs & stability assessment for piling rigs and other construction machinery, geostructural designs for approximately 1km total run of permanent bored pile retaining walls to support the split-level construction on the sloping site and geostructural designs for the permanent foundation piles to support the housing units. The paper details how the four factors outlined above were amalgamated by the project’s foundation specialist consultants & piling contractors to deliver safe and practical solutions for the development, with significant savings in materials, cost and project completion time.

Sep 8, 2021

By James P. Chivilo, Gregory R. Meeder, Scott J. DiFiore, Matthew H. Johnson

New construction in metropolitan areas has direct impacts on immediate neighbors and abutters. While noise and dust are generally nuisance concerns, demolition, vibrations, excavation, and dewatering can cause structural damage to adjacent structures. Different cities, states, or jurisdictions have different regulations that dictate requirements, roles, or responsibilities for varying parties during construction. The authors will introduce and discuss risks of new construction adjacent to existing structures, and the legal framework in Illinois which requires the owner of the new construction project to provide adequate protections for adjacent existing structures. The authors, who are engineers and attorneys, will discuss technical and legal concerns, and will highlight the importance of early and frequent communication among project participants to manage risks, despite whether or not any local regulations exist to drive the process. RISKS IN ADJACENT CONSTRUCTION New construction in metropolitan areas inherently involves some combination of noise, dust, ground-borne vibrations, earth excavation, and subgrade dewatering. These issues have potential to directly and adversely affect abutters and their property. Noise and dust can be nuisance concerns, while vibrations, excavation, and dewatering can result in damage to abutters’ structures. Noise and dust are unlikely to lead to physical damage to abutters’ property, and can be controlled with limited work hours and good housekeeping practices. Vibrations and excavations, however, if not well understood, planned for, and mitigated, can result in serious damage to abutters’ structures. In turn, this damage introduces additional and often significant costs and schedule delays.

Jan 1, 2019

By Ryan T. Smith, Anthony Sahj, Alexander T. Darnell

Every second can count when trying to board a departing flight or catch a ride-share to your final destination. Hartsfield-Jackson Atlanta International Airport is in the midst of a project that aims to cut about 13 seconds between automated people mover trains (Plane Train) that move passengers between the terminals and concourses. The project involves extending the Plane Train tunnel west from its existing terminus under the domestic terminal. Working from inside non-public areas of the terminal, Keller North America, Inc. (Keller) incorporated systems of micropile-supported steel beams and grillage to both underpin existing columns prior to tunneling and support open-cut excavation at the tie-in of the new to the existing tunnel. Dewatering aided in mining a challenging section at the start of the drive of the mixedface, sequentially excavated tunnel and an automated instrumentation system monitored the performance of the construction and its impact to the terminal. Cut and cover egress and ventilation tunnels required braced support of excavation.

Oct 1, 2022

By Brandon T. Buschmeier, Sonia S. Swift, Michael P. Walker, Frederic Masse

"Ground improvement has undoubtedly become a cost-efficient and effective solution to support the development of poor soil sites. Ground improvement elements, such as Controlled Modulus Columns (CMCs), replace piles by improving the subsurface soils and reducing settlement. As ground improvement becomes more popular, the applications become more creative and ground improvement is being used to control settlements under large structures with tight settlement tolerances.In this paper, we will discuss the use of CMCs to support two (2) large industrial warehouses where soil conditions would normally lead to the use of deep foundations and a structural slab, grade beams, and hung utilities to prevent excess settlement. Each of the sites we will discuss had poor soil conditions in the form of very soft or compressible soil, heterogeneous fill of varying thickness, and environmental contamination. At each site, we developed a design that would allow for the use of Controlled Modulus Columns (CMCs) with a Load Transfer Platform (LTP) in place of the previously-proposed deep foundations. The use of the CMCs also allowed for the use of spread footings and slab on grade construction. The benefits of this value-engineering approach include economy in the foundation system, risk mitigation by not disturbing contaminated soils requiring expensive removal, and ease of access for future sub-slab upgrades with new tenants. Additionally, the use of recycled concrete aggregate as an LTP is more environmentally friendly than placing structural slabs with heavy steel reinforcement.Designing for the settlement of large warehouses is challenging because it requires changing how we typically perform our designs. For most structures, the slab loads are relatively light when compared to the footing loads, whereas for warehouses, the slab is heavily loaded compared to the relatively light footing loads. Thus, it becomes essential to perform three-dimensional analyses to confirm that the proposed CMC layout will provide uniform support of the slab and footing across a variety of loading scenarios (loaded bays vs unloaded or travel bays). The complexity of the designs for these warehouses generated interest in conducting large area load tests over a grid of multiple columns. The performance of the area load tests provided invaluable information on the effectiveness of the LTP and CMC spacing. In this paper, we present a general description of CMC ground improvement, the differences between ground improvement and traditional pile foundations, our typical design methodology for CMC design, and the modifications to that methodology for warehouses."

Jan 1, 2017

By Ian Vaz, Takefumi Takuma, Rafael Holcombe, Chris DellAringa

"This paper will discuss the successful installation of seawalls for the first phase of a project in Long Beach in California known as the Naples Island Permanent Seawall Repair – Phase 1. How an unconventional method of pile driving resulted in the reduction of the duration of the project while using less space and maintaining minimal noise impacts to accommodate neighbors will also be discussed. Included in the paper will be how non-vibratory equipment used on this project also significantly minimized the risk of disturbances as well as settlement on residential properties; which in turn greatly reduced the risk of damage to existing structures. The first phase of a 6-phase project along a section of the canals with tight clearances and proximity to residents included the installation of a 1,912 linear-foot steel sheet pile wall system in front of the existing deteriorating walls from January until March 2015.INTRODUCTIONThis project was located in the Naples Island neighborhood of Long Beach in southern Los Angeles County, California. After 80 years of the same seawall structures lining the canals of this beautiful neighborhood, the City of Long Beach Department of Public Works decided that it was time to better protect the area’s multi-million dollar homes by repairing its crumbling seawalls. The City realized that the walls will only become worse due in part to several concerns, including bending failure for the already deflecting walls. According to the City, certain sections of the walls had a significant risk of global failure if the area experienced a “moderate” near-source earthquake (City of Long Beach, CA, 2014b). Although the seawalls were in need of major repair, this would not be simple. Due to the tight clearances of the seawalls between the homes and canals, installation would be difficult with heavy, conventional construction equipment.Phase 1 of the project involved installing sheet piles on the water side in front of existing and aging vertical concrete seawalls between the Ravenna and Toledo Bridges along the Rivo Alto Canal. See Figure 1 for the General Plan for Phase 1. Financing for this project by the City’s Tidelands Capital Improvement’s Division allowed the construction to begin in a timely manner. However, the challenges for the City included regulatory restraints that further complicated the construction in terms of the duration of the project due in part to numerous regulations from several regulatory agencies."

Jan 1, 2016

By Satyajit Vaidya, Rudolph Frizzi, Sandy Larimer

"This paper presents a case history in design and construction of a deep foundation system that included high-capacity open-ended driven piles constructed to support a high-rise building in Manhattan, New York. The project site is bordered by existing buildings, active streets, and critical public transportation infrastructure, which were considered in the new building’s deep foundation and seismic design. This paper focuses on driven pile foundation design and installation through relatively loose soil deposits. Unique design aspects included seismic design considerations, and pile splice design for open-ended steel pipe piles subject to significant uplift and lateral loading. Unique construction aspects included quality assurance of open-ended steel pipe pile splices, and uplift and lateral load testing of driven piles installed in close proximity to other foundation elements installed for the project.SITE CONDITIONS AND SUBSURFACE CONDITIONSThe project site is located in Manhattan, New York, and is bordered by existing buildings, active streets, and critical public transportation infrastructure that is located about 60 feet from the site. The existing sidewalk grades around the site are between about el 4 and about el 13; elevations are referenced to the North American Vertical Datum 1988 (NAVD88).Subsurface conditions at the site generally consist of successive strata of historic fill, former river bottom deposits consisting of compressible clayey soils, and medium dense to dense sand, overlying mica schist bedrock. A generalized subsurface profile is shown in Fig. 1. The historic fill stratum is about 10 to 45 feet thick, and generally consists of loose to medium dense sandy soils with varying proportions of silt, gravel, and miscellaneous debris such as brick, concrete, and glass fragments. The underlying former river bottom deposit stratum is up to about 15 to 20 feet thick, and generally consists of very soft to very stiff clay and lenses of very loose to loose sand. Medium dense to dense sand was generally observed below the historic fill and former river bottom deposit strata and overlying bedrock. Top of bedrock was generally observed at about 80 to 105 feet (i.e. at about el -75 to el -100), except in the southeastern portion of the site where the top of rock was observed as deep as about 140 feet (i.e., at about el -135). Groundwater levels typically ranged between about el 1.5 and el -0.5."

Jan 1, 2016

By Alessandro Bertero, Manuel Toniolo, Vincenzo Tirozzi

"The installation of foundation elements (large-diameter Bored Piles or Diaphragm Walls) for the execution of underground works to be performed through the ""Top Down"" Technique (Stations, Car Parks, Subways, Artificial Tunnels) often requires the insertion, with pinpoint accuracy, of steel or prefabricated elements within the foundation system, to provide temporary and/or permanent support to the whole structure.The future high-speed railway station of Florence Belfiore (Italy) is a perfect example; the new station will be built in the Northwest area of Florence, about two kilometers far from the existing station of Santa Maria Novella. The project envisages installation of about 500 bored piles (1200-1500-2100 mm diameter), with lengths ranging between 50 and 70 m. In the upper inner part of 250 piles, a steel pipe (weight: 15-20 tons, length: 22-25 mt.) has to be inserted with pinpoint accuracy.The “TREVI-CALATORE” system allows to install the plunge columns and adjust their position and verticality.INTRODUCTIONThe execution of underground works via the ""Top Down"" technique, train or tube underground stations, parking shafts, tunnels, often implies the need to carefully insert steel or prefabricated structures, serving as provisional/definitive pillars, into the foundation elements.The future high-speed railway station of Florence Belfiore is a perfect example; the new station will be built in the Northwest area of Florence, located about two kilometers far from the existing station of Santa Maria Novella.The new Belfiore Station is part of the new European high-speed railway network. The works related to Florence urban penetration include (figure 1):•,a 6.5 km. twin tunnel excavated via TBM/EPB, that will run beneath Florence in a north-east direction,•,passing under more than 150 buildings, many of which can be considered historic buildings, with a soil•,coverage ranging from 6 m to 20 m;•,a North portal in Rifredi area, Firenze Castello Station;•,a South portal near Campo di Marte Station (which is also the launch shaft of the TBM)•,the new Underground Station in Belfiore area."

Jan 1, 2016

By Scott A. Walker, Gabriel J. Alcantar, Brian Zuckerman, Ramin Golesorkhi

"The stadium development consists of construction of a 68,500-seat, open-air NFL football stadium for the San Francisco 49ers. The main structure will consist of a 7-story above grade steel structure supported by over 3,000 piles. Berkel and Company Contractors, Inc. (Berkel) was selected as the design-build pile contractor who used their auger pressure grouted displacement (APGD) piles for this project. During an indicator pile installation and pile load test program, fifteen piles were tested to develop installation criteria to support demands of 150kips tension and 180 kips compression. Following the indicator pile program Berkel installed 3088 piles in 30 working days. Throughout pile installation data were collected with an automated data acquisition system (DAS). During pile installation field engineers from Treadwell & Rollo observed the pile installation as well as the real-time data from the DAS. Strategic staging and pre-production planning by Berkel along with consistent collaboration with the design team created an atmosphere for a successful and on schedule project completion.IntroductionThe new San Francisco 49ers Stadium in Santa Clara, California will be a 68,500-seat facility, a rendering of which is shown in Figure 1. The main structure will consist of a 7-story above grade steel structure supported by more than 3,000 piles. The north, east and south portions of the stadium are designed as an open seating bowl, while the western portion includes open seating at the lower levels and seven-story tower which houses over 150 suites.The stadium project includes the stadium structure, as well as elevated open pedestrian walkways, commercial community space, and three new pedestrian bridges spanning a nearby by creek. Sustainable designs and innovations such as a green roof, photovoltaic panels, a ground source geothermal system, stadium-wide Wi-Fi capability, and access to public transit are provided throughout the project. The stadium is designed as an open, light, and airy structure and is surrounded by an existing amusement park, office buildings, the Santa Clara Convention Center, and the training facility of the 49ers."

Jan 1, 2015

By David C. Kraft

Atlas Systems, Inc. (ASI) resistance type piers were used to underpin a 100 year old historic structure at Fort Monroe, Virginia. This 3-story structure with basement was underpinned with 155 steel tubular push piers (4" OD) that were hydraulically installed to depths ranging between 90 and 110 ft. and to installing forces in excess of 60,000 lb. Project requirements included lowering the basement floor by 1-1/2 ft. and constructing new footings and adding stem walls to connect to the existing masonry walls. Additionally, the underpinning piers were temporary which required the development of a decoupling system to permit the transfer of the building loads from the underpinning piers to the new footings. The structural loads at the foundation level required a c. to c. pier spacing of 3.75 ft. in order to meet project requirements of a minimum Factor of Safety of 3.0 on the pier load capacity. Project requirements included a load test on the selected underpinning pier (ASI - AP2 4000.219) in order to establish installation depths for seating the piers to 60,000 lb. The project was successful in supporting the full load of the structure during the construction phase. Considerable savings in time and cost were achieved as well as avoiding any vibrations or noise during installation of the piers.

Jan 1, 2002

By Robert Bachus, Nikolaos Machairasm, Allen Cadden

Data Interchange for Geotechnical and Geoenvironmental Specialists (DIGGS) is a data transfer standard that is gaining widespread acceptance in the geotechnical and geoenvironmental communities. Originally developed using funding from the Federal Highway Administration (FHWA) to efficiently capture data related to geotechnical boring logs, cone penetration test (CPT) soundings, and lab testing results, the data transfer protocol is rapidly gaining traction. It has been shown to have beneficial impacts in other allied areas where disparate parties (i.e., consultants, contractors, vendors, etc.) routinely publish/submit data as part of project deliverables. The historic problem is that many of these submissions use paper copies (i.e., .pdf images) to transmit valuable data for the project… data that may extend beyond the “technical” aspects of the project (e.g., equipment operating conditions, construction production rates, project costs, etc.). These data could be used by multiple parties to assess project performance and safety, as well as to track productivity, etc. Currently, in the limited situations when actual data are compiled and transmitted, the data often are submitted as an author-specific (and often proprietary) software application and must then be re-entered into other software applications (e.g., analysis software, database, etc.) for use beyond simple data collection. An initiative undertaken by the Geo-Institute (G-I) of the American Society of Civil Engineers (ASCE) focuses on exploiting the full potential of DIGGS to geoprofessionals both within and outside of the transportation community. The deep foundations industry represents one community that could benefit significantly from using DIGGS. Data of interest to DFI members include production records, quality assurance information (e.g., verticality and alignment, concrete strength), and, importantly, load test results. When adopting DIGGS, users need not modify how they capture data, but rather will use DIGGS as a vehicle to transfer data to other applications in a standard format where it can be shared, used, stored, and retrieved. This paper and associated presentation will describe DIGGS and demonstrate how DIGGS can be used effectively within the deep foundations community.

Jan 1, 2019

By John P. Turner, Mark Jen, Bobby Daita

"The Port Authority of New York and New Jersey is replacing the existing Goethals Bridge built in 1928 which is deemed to be functionally obsolete. The replacement bridge will consist of a dual cable-stayed Main Bridge crossing the Arthur Kill with elevated approach spans connecting Elizabeth, New Jersey and Staten Island, New York. The main bridge towers are supported on a group of six nine-foot diameter drilled shafts that transition into a pier cap. The anchor and approach piers are supported on two column bents with each column supported on a single drilled shaft. The 4.5 to 10 feet diameter drilled shaft foundations have permanent steel casing to rock and socketed into bedrock. Subsurface conditions consist of Passaic Formation bedrock overlain by varying thicknesses of overburden soils. The foundation design assumes permanent casing extending a minimum 2 feet into the weathered bedrock. Rock socket lengths below the permanent casing vary between one to two shaft diameters based on the quality of the bedrock. The reinforcing design was based on AASHTO LRFD minimum requirements, force demands, seismic detailing requirements and also considering the continuity between the shaft and socket.The bridge is currently under construction with approximately 70 percent of the foundations installed. Several field conditions encountered at various stages of shaft construction between casing advancement and concreting required design and construction modifications. Based on the driving method and the quality of the bedrock, the tip of the permanent casing hit refusal either above or below the design elevation, requiring modifications to the drilled shaft design and its reinforcement. This paper provides an overview of the general subsurface conditions at the site and its impact on foundation design and discusses the detailing worked into the design to accommodate tip elevation variations, as well as various foundation design modifications in response to actual conditions encountered during construction."

Jan 1, 2016

By Dempsey S. Thieman

Innovative marine bulkhead design and construction techniques were used in the fast-track design and construction of a high-capacity, deep-water dock in the highly seismic region of Alaska?s Aleutian Islands. The geotechnical investigation and design through construction phases were completed in just eight months. The adaptable OPEN CELL® design, readily available standard flat sheet pile and an experienced contractor were integral to the successful completion of the project. The cost of the structure was determined to be approximately 50 percent of a comparable pile-supported platform dock structure, allowed higher load capacity, rapid construction, less maintenance, and provided substantially more uplands. This paper details the design and construction of this unique and challenging project. The OPEN CELL structure is a vertical flexible membrane system that offers significant advantages over other structure types: ? Its flexible membrane structure is not dependent on toe embedment for stability. ? Poor soil conditions, shallow bedrock, high seismic loads, deep water, scour, etc., can be accommodated due to its adaptable design. ? It has a very high load capacity?capable of several thousand pounds per square foot. ? Allows buried utilities which results in lower cost and reduces freezing conditions ? The sheet pile tail walls can be extended to provide increased global stability if needed. ? Standard sheet pile and connectors with traditional installation techniques allow accelerated construction schedules.

Jan 1, 2008

By Eric P. Bregman, Justin Zarrella, Ryan M. Coulson, Connor Johnson

Within a prominent Boston, MA suburb are a pair of historic stone and mortar structures built in the late 1800’s. Both the Main House and Carriage House have been maintained and occupied throughout their rich history, but renovations were needed to address structural concerns and building code compliance issues. The focus of this paper is to detail an innovative underpinning design that addressed ongoing settlement issues at the Carriage House. GZA GeoEnvironmental, Inc. (GZA) partnered with Phoenix Foundation Company, Inc. (Phoenix) to design foundation wall support systems for Consigli Construction Company (Consigli) that would effectively underpin the historic field stone foundations. Originally, conventional concrete pit underpinning and jet grouting were contemplated as methods for support. However, due to the age and condition of the existing foundations, worker safety concerns, and the risk of additional structural damage, GZA/Phoenix elected to pursue a less traditional approach. The alternate design consisted of micropiles used for combined temporary and permanent foundation support. The load transfer system included steel headers with needle beams cored through the field stone foundation walls and reinforced concrete grade beams/pile caps. To validate design performance and ensure worker safety, GZA installed a fully automated survey monitoring system to record lateral and vertical building deformations. This included real-time email alert notifications to inform the Project Team of any threshold exceedances. From the start of micropile drilling through full load transfer to the temporary support and permanent foundation systems, the underpinning performed as designed resulting in less than 3/16-inch of vertical and horizontal deformations observed. This magnitude of movement is less than half of what is generally accepted deformation tolerances for masonry structures and considered exceptional performance. The focus of this paper is to provide additional details on the unique design, sequencing, installation, and performance of the underpinning systems.

Sep 8, 2021