Search Documents

By H. Houali

Corrosion is an electrochemical process that causes degradation and deterioration of various steel works (pipelines, drains, cisterns) whether they are buried, immersed, or not. Worldwide, we estimate that corrosion destroys a quarter of the annual production of steel at a rate of 5 tons per second. Several techniques are used to protect against corrosion. Among these processes, Cathodic protection, which is regarded as the best technique to assure the protection of steel, works against this phenomenon. This is achieved either by a system of reactive anodes, or by the technique of impressed current protection or other techniques. Before any installation of cathodic protection, a preliminary study and pre-evaluation of certain parameters must be made. In the present work, we will present an example of dimensioning of an installation of cathodic protection by imposed current of a pipeline using solar energy, where we discuss the following items: ? Evolutions of the potential as well as current along the pipeline and their respective expressions deduced from the laws known as telegraphists; ? Range of protection (potential of protection along the pipeline); ? Influence of the isolation resistance of the coating on the range of protection; Effect of the aging of the coating and its influence on the current of protection

Jan 1, 2005

By J. Fixter, P. Prangnell, Z. Pinter, E. Eimer, B. Chehab

"High deposition rate Wire and Arc Additive Manufacture (WAAM) can provide benefits to the aerospace industry, including a reduction in lead time, reduced material waste and, through higher solidification rates, refinement of the as-built microstructure relative to a cast material. However, candidate 2xxx series high strength alloys for this process normally require a solution treatment, which is problematic for large near-net-shape components, and age hardening to achieve maximum mechanical properties. With each layer being subject to multiple thermal cycles, exploiting the thermal conditions in the WAAM process to avoid post-build solution treatment is therefore of interest. A solutionisation model has been developed for the WAAM process, based on diffusion controlled dissolution using DICTRA, which was validated through thermal simulations combined with 2D and 3D image analysis. The model has subsequently been used to simulate the solutionisation behavior during a typical WAAM thermal cycle and to explore what could theoretically be achieved by, for example, refining the starting microstructure.INTRODUCTION There is currently great interest in exploiting additive manufacturing (AM) in the aerospace sector due to several benefits it can potentially provide; including reduced material waste, shorter product lead times and greater design freedom (Herzog, Seyda, Wycisk, & Emmelmann, 2016). However, with aluminium alloys the material properties obtained are generally inferior to those of conventional high-strength wrought products; therefore more research is required to explore the potential for exploiting the unique process conditions in AM to improve the as-deposited microstructure. A range of AM techniques are now available (Debroy et al., 2018), which differ in terms of the feedstock type and power source and it is necessary to match the appropriate technology to a particular application. This generally requires a compromise between the build rate and shape resolution. Wire and plasma-arc additive manufacturing involves using an electric arc to melt wire onto a substrate, and fabricates a part by building up overlapping layers of deposited weld beads (Addison et al., 2015; Williams et al., 2015). The benefits of this process over other AM methods are the much higher deposition rates (e.g. kg’s/hour) achievable and lower capital equipment costs relative to powder bed techniques, which makes it suitable for large scale applications. However, limitations include a lower part complexity, lower solidification rates and a greater need for post-process machining (Frazier, 2014)."

Jan 1, 2018

By K. Thuro, H. Käsling, C. Wieser, G. Nuijten

"The time-dependent behavior of brittle rocks during stress relaxation is of great interest for mining industry, nuclear waste disposal as well as tunneling and underground construction. Several studies have shown that both elastic as well as inelastic deformation occur during stress relaxation (Emery, 1964; Zang & Berckhemer, 1989). While elastic strain occurs already during the drilling process, inelastic deformation is time-dependent and can endure for hours, days or weeks. To investigate the evolution of microcracks during core relaxation, two crystalline core samples were recovered from high in situ stress conditions in Europe’s deepest mine in Pyhäsalmi (Finland). Samples were prepared for testing within one hour after coring such that a large portion of the time-dependent component of relaxation could be recorded over several days using ultrasonic velocity as well as acoustic emission (AE) measurements.Results from AE analysis show an exponential decrease in the number of events over a period of several hours. Repeated sudden increases of acoustic events can be related to the propagation or the interaction of cracks. In the first hours of recording also the signal energies reached the highest values and the increases in signal energy correlate well with increased event rates. On additional drill cores, P-wave velocities were measured parallel and in 45° distances perpendicular to the core axis. After core recovery, stress-induced microcracking caused an exponential decrease in wave velocities similar to AE rates. Lowest compressional wave velocities were measured parallel to the core axis and thus normal to the foliation and in the direction of the maximum in situ stress component. The highest measured velocities occurred parallel to the foliation plane. Within the samples, the anisotropy ratios were up to 1.37 at the beginning of the measurements and increased to values of up to 1.8 after 45 days. The wave velocity anisotropy is in agreement with the in situ stress orientations."

Jan 1, 2015

By B. Arsenault

Aluminum coatings can provide galvanic cathodic protection for several metals and alloys, In order to be a suitable protective solution on structural components, the mechanical integrity of the component must be preserved, In particular, fatigue properties are a challenge for thermal-spray protective coatings on mechanical structures, To address the issue of the fatigue integrity of 7075 aluminum alloy with an arc-sprayed protective coating, different surface preparations prior to arc spraying were considered, In the present work, a feasibility study was performed using laser ablation as a surface-preparation technique before or during arc spraying of coatings, This was collaborative effort between the LERMPS laboratory in France, the National Research Council Canada and the Royal Military College of Canada, Both fatigue and adhesive properties of aluminum coatings were evaluated in relation to substrate-surface-preparation techniques including laser ablation (Protal® process), grit blasting and shot peening. Results indicate that a combination of key conditions, including the use of nitrogen as the arc spray gas, shot peening, and proper laser energy density for ablation, provide high fatigue resistance of metallic coated 7075 alloy substrates. Specimens prepared under these conditions show a similar fatigue resistance to uncoated substrates.

Jan 1, 2005

By R. Sharma, I. Miskovic, S. Miskovic

Solvent extraction (SX) is a widely used method for the extraction of copper from pregnant leach solutions or other ionic solutions in hydrometallurgical applications. About 17% of total refined copper production worldwide is produced using SX followed by electrowinning (EW). Conventional SX units, such as mixer-settlers, consume a large amount of extractant, offer poor process control and yield low extraction efficiency. Extraction efficiency is poor due to low specific interface area, crud formation, emulsification, and slow phase separation stage. Micro solvent extraction (micro-SX) is a rapidly developing technology that provides an opportunity for improved process control, higher extraction efficiency, lower residence time and, as such, has a potential to reduce the environmental footprint of SX operation. In this research, extraction of copper ions in an acetate buffer media is investigated using D2EHPA with kerosene as a diluent. Chemical factors such as extractant concentration and ionic concentration of aqueous phase are varied to determine the optimum conditions. Subsequently, the extraction efficiency and reaction time of new micro-SX reactors are compared against previous bulk SX studies. Extraction in the microfluidic reactor was observed to be faster with a residence time more than an order of magnitude lesser than bulk SX. This study forms a prelude for developing new modular micro-SX units which will enable continuous, effective, and safe operation on a large scale. In future studies, numerical and analytical models validated through this work will help eliminate rigorous experimentation and enable faster design and fabrication of micro-SX units. INTRODUCTION Conventional industrial solvent extraction (SX) units such as mixer-settlers, extraction columns present various disadvantages. Low specific interfacial area, crud formation, and emulsification in industrial reactors lead to long extraction times and severely hamper extraction efficiency (Priest et al., 2011; Chen et al., 2017). Microfluidic extraction considerably improves upon the current extraction practices by (1) creating a large surface to volume ratio that enables rapid mass transfer across the interface, (2) better process control, and (3) easier separation of phases (Kashid, Renken, & Kiwi-Minsker, 2011; Ciceri, Perera, & Stevens, 2014). These factors establish micro-SX as a crucial mode for process intensification. Although, a micro SX unit has significantly low processing volume than conventional extraction methods, their throughput can be increased via massive parallelisation (‘numbering up’), which is an area of active research (Darekar, Singh, Mukhopadhyay, & Shenoy, 2016a; Kriel, Woollam, Gordon, Grant, & Priest, 2016).

Jan 1, 2019

By Fathi Habashi, Ahmet Deniz Bas

"The mechanism of leaching of semiconducting minerals such as PbS, ZnS, UO2, etc., has been the subject of intensive speculation by hydrometallurgy researchers in the early 1950s who assumed the formation of intermediate surface complexes that could be neither separated nor identified by physicochemical techniques. The electrochemical theory of leaching introduced in the late 1960s resolved this problem by comparing the leaching process to a corrosion phenomenon similar to the corrosion of metals. Few years later, experimental evidence showed that anodic and cathodic zones are formed on the dissolving mineral although no electric current is imposed on the mineral during dissolution. A discussion of these findings is outlined.INTRODUCTIONIn the early 1950s researchers realized that kinetic studies for leaching ores are as important as thermodynamic calculations. It was also during this period that the concept of species adsorption on mineral surfaces has dominated the interpretation of the mechanisms of most reactions. This may have been due to the fact that many researchers of this period came from the mineral dressing sector and were influenced by flotation theories. However, when the knowledge of lattice defects and the semiconductivity of minerals became known and their importance in extractive metallurgy was realized, there was a need to explain the leaching reactions in light of these modern theories (Habashi, 1969, 1970). Semiconducting minerals of importance in metallurgy are two categories: the sulfides such as those of copper, lead, zinc, and the oxides such as those of uranium."

Jan 1, 2016

By Norman M. P. Low

"IntroductionIndustrial applications of mica utilize two commercially important varieties of mica: muscovite and phlogopite. Muscovite mica is a potassium mica with a general chemical formula, H2KA1(Si04)3 h, and is sometimes referred to as a potas hsilicate. Phlogopite is a magnesium mica having a general chemical formula, H2KMgSi(Si04)3, and is distinguished from the muscovite mica by its decomposition in sulphuric acid.Canada is one of the major natural mica producers in the world. A large tonnage of the mica powders is at present mined and processed in the Eastern Townships of Quebec. This Canadian mica is of the phlogopite type. A closely related mineral of the mica family which is widely used in the construction industry is vermiculite. It is a dehydrated magnesium-aluminum-iron silicate characterized by a foliated structure. Expanded vermiculite, which is often referred to as exfoliated mica, is used as many types of thermal and acoustic insulation, as loose fill in buildings, as an aggregate in concrete, as an ingredient in plaster and insulating concrete , and in fire-proofing compositions. Natural phlogopite and muscovite mica powders are used extensively as reinforcing agents in organic polymers. They also have a wide range of applications in commerical products. For example, dry-ground mica powders are used in large tonnage as a surface finish in roofing materials and as a bonding agent in wallboard joint cement. Common products such as paint, rubber, plastics and welding rods contain mica. Recent studies have also shown that mica powders can be added to portland cement in the preparation of concrete products, as they could improve the tensile strength of the concrete products. The potential and possible"

Jan 1, 1982

By Z. Xie

Gas diffusion electrodes (GDEs) for high temperature polymer electrolyte fuel cells (PEFCs) have been prepared using ZrP-modified Nafion ionomer. The performances of these GDEs as cathodes and anodes were evaluated and compared with conventional Nafion ionomer GDEs using Nafion 112 as the PEM under elevated temperature and reduced relative humidity. ZrP-modified Nafion ionomer was incorporated into the catalyst layer to enhance water retention and/or increase the protonic conductivity. The fabrication of ZrP-GDEs was implemented by the ion exchange of Nafion solution with zirconyl chloride, followed by the impregnation of GDEs in H3PO4 solution. The composite electrolytes in the catalyst layer possessed a ZrP content of 20% by weight. GDEs were characterized by TGA, SEM, XRD, and CV. Scanning electron microscopy (SEM) indicated evenly distributed elemental Zr and P within the catalyst layer. Cyclic voltammetry shows a reduced electrochemically-active surface area when the ZrP is incorporated into GDEs. Polarization and impedance analyses indicate the cathode with ZrP-modified Nafion ionomer did not show an enhanced or decreased performance, compared with conventional Nafion ionomer GDEs under elevated temperature and decreased humidity. However, when GDEs with ZrP¬Nafion ionomer were used as the anode, an improved performance was observed. Preliminary experiments show that the anode is more sensitive to dehydration than the cathode under elevated temperature and/or low humidity. Improving the anode water retention capability will help to reduce losses at the anode. However, the incorporation of hygroscopic agents in the cathode catalyst layer is not essential because it is self-humidified by electrochemically-produced water even under elevated operating temperature and lower humidity.

Jan 1, 2005

Why innovate? ? How are we doing in Canada? ? How can we do better? ? Why now? ? What?s next? ? Lowering production costs ? Improving productivity ? Increasing value-added ? Discovering new mines, extending life of existing ore bodies ? Reducing environmental footprint ? Improving health and safety

May 1, 2008

By A. -M. Cadieux

During the geological synthesis of the Réservoir Pipmuacan area (NTS 22E) by the Ministère des Ressources naturelles (Québec), several ilmenite-apatite occurrences, some well-known and some recently discovered, have been examined. These occurrences are hosted in the Lac-Saint-Jean and Labrieville AMCG anorthositic suites. The Lac-Saint-Jean Anorthositic Suite (1160-1140 Ma), composed of multiple intrusions covering an extensive surface area, is characterized by labradorite plagioclase. The Labrieville Anorthositic Suite (1010-1008 Ma) is characterized by andesine plagioclase. It was previously known as the Labrieville Anorthosite, which was composed of a small isolated pluton located east of the Lac-Saint-Jean Anorthositic Suite. However, new geochronological data and field observations indicate that the Labrieville Anorthositic Suite in fact includes several intrusive bodies, namely the La Hache Monzonite and the Mattawa Anorthosite. A series of major structures (Saint-Fulgence, Pipmuacan, and Chute-des-Passes deformation zones) and their conjugate faults played an important role in the emplacement of the Lac-Saint-Jean Anorthositic Suite. The Saint-Fulgence deformation zone appears to have been involved in the emplacement of the Labrieville Anorthositic Suite. Oxide mineralizations are abundant in both anorthositic suites. Ilmenite, magnetite (± titaniferous), and apatite assemblages are found mostly in the labradorite-type anorthosites, while hemo-ilmenite, magnetite and apatite assemblages are associated only with the andesine-type anorthosites. Field works has revealed ilmenite-apatite mineralizations in a variety of settings, with grades reaching 48% TiO2, 16.2% P2O5, and 71.7% Fe2O3 (tot). Numerous oxide-bearing gabbronorites, often accompanied by or located near massive apatite-oxide accumulations (nelsonites), were discovered. Among these oxide-rich zones, breccia zones with anorthosite enclaves in an oxide matrix (ilmenite-magnetiteapatite) have been observed. Locally, ilmenite-apatite mineralization occurs as cumulate concentrations in ultramafic rocks. Evidence has been observed for immiscible magmas, for magmas differentiated from a mangerite or jotunite parent, and even for late magmas differentiated from the anorthosite magma itself (apatite-bearing anorthosite). Finally, the northern part of the Lac-Saint-Jean Anorthositic Suite hosts sulfide and vanadium mineralizations associated with ilmenite-apatite enriched zones, with grades reaching 1.48% Cu, 1.22% Ni, 1.6% Cr2O5, 0.25% Co, and 0.52% V2O5.

May 1, 2003

By N. Shi, T. G. Joseph

ABSTRACT A revised equilibrium approach to evaluate dipper-ground interactions during the dig cycle of ultra-class mining shovels operating in soft unblasted uniform ground conditions is presented. A review of previous approaches, leading to an outline of the modifications and ground condition considerations, is made in support of the reasoning and basis for the derivation presented. An analytical solution is provided to the scenario of a cable shovel dipper digging in soft ground material such as oil sands.

Jan 1, 2012

By K. Hawboldt, J. E. Halfyard, C. Bottaro

The removal of sulfur from leach residues has been practised in the zinc industry using a combination of flotation and hot melt filtration. The process is highly dependent on the nature of the concentrate and the subsequent residue. When the mineral constituency of the residue alters, the process can encounter significant operational challenges. An alternate method of converting elemental sulfur to water-soluble polysulfides was applied to leach residue from Vale's nickel demonstration plant in Argentia, Newfoundland. Reaction parameters, sulfur purity and other key indicators are discussed as is the potential commercial application.

Jan 1, 2011

By T. C. Chudy, C. C. Hamilton, G. R. Lane

The selection and provision of mineralogical services to assist in developing a GeoMetallurgical program for a Cu Porphyry Mine in South America is covered in this paper and presentation. The objectives of the study were to provide a rapid mineralogical scoping protocol to support and confirm results of sequential Cu leach data and to provide detailed mineralogical analysis of four composites and products on which locked cycle test-work were performed. Results showed good reconciliation was achieved between measured chalcopyrite and secondary Cu mineral contents with leach data using a linear intercept mineralogical procedure by TIMA (Tescan Integrated Mineral Analyser), as well as a generally positive correlation between pyrite and Cu-sulphide grain size. Size-by-size analysis of Composite feeds and test products was used to outline comparisons between feeds on a mineralogical basis and provide liberation and association data with which to diagnose and better explain performance. Identifying key mineralogical drivers to Cu recovery and concentrate grades using these results, a greater understanding of the role of chalcocite and pyrite on metallurgical performance was established. INTRODUCTION As a global supply of copper, porphyry copper deposits are typically very large, often in excess of a billion tons of ore (Keeney, Walters, & Kojovic, 2011; McMillan & Panteleyev, 1980) with grades typically between 0.2 and 1.2% Cu, and up to 2% Cu in places. They are also a source of gold. The complexity of copper porphyries arises from their classically zoned nature, the type of host rock, as well as whether or not they have been overprinted by oxidation, weathering and supergene enrichment (Sillitoe, 2011). Zones of alteration and other geological attributes give rise to varied mineralogy, ore mineral textures and material properties, all of which result in different processing characteristics. Due to the interdependencies of geological and processing characteristics, it is vital to study links between the geology at the macro-scale and mineralogical features down to millimeter and micrometer scale (mineral content and texture) and their influences on mineral processing behaviour (Cropp, Goodall, & Bradshaw, 2013). The growing field of GeoMetallurgy aims to provide an Orebody Knowledge framework by which to gather such information as it pertains to: (1) Understanding and predicting likely flotation response; (2) Guiding relevant test work to investigate and validate links, interdependencies, theories and data interpretation/evaluation; (3) Populate a block model with relevant information and; (4) Implement and refine the model for ongoing optimization and control. Specific questions addressed by using mineralogy often include flotation diagnostics as aids to interpretation, causes of dilution and losses to tailings, as well as guidance to sampling for test work (Cropp et al., 2013).

Jan 1, 2019

By Mahmoud Ahmed

Three-dimensional models are in increasing demand for design, maintenance, operations and construction project management. Point-clouds are the main output of automatic data collection using laser-scanners and photogrammetric technologies. Pipe-works may comprise 50% of the value of important construction projects such as industrial and research facilities. We have developed a practical and cost-effective approach, based on the Hough-transform and judicious use of domain constraints, to find, recognize and reconstruct/model 3D pipes within point-clouds fully automatically. The developed approach allows pipe growing within a 3D point-cloud. It samples the point-cloud to sequential orthogonal slices, detects pipe?s cross-sections within sampled slices and grows the pipe along the cross sections centerlines. It is validated using laser-scanner data from construction of the Engineering-VI building on the University of Waterloo (UW) campus. The system works on a typical laptop. Recognition and localization results are within a few millimeters. The presented approach opens the gate to broad applications of pipe-network modeling.

Aug 1, 2013

By A. de Ville d’Avray, G. Guezennec, P. Wavrer, E. Braak

The aim of the European CEReS project was to develop an innovative copper recycling route based on the coprocessing of coal production waste by bioleaching and printed circuit boards (PCBs) from Wastes of Electrical and Electronic Equipment (WEEE). Coal waste is processed by bioleaching in stirred tank reactors, and the resulting bio-lixiviant solution is used to extract copper from PCBs pre-treated by catalytic cracking. Copper is then extracted using solvent extraction, stripping and electrowinning. The whole process flowsheet combines thermal, biotechnological, physical and hydrometallurgical operations. Once the process concept has been validated at laboratory scale, a simulator of the whole process has been built in the USIM PAC software platform. The tool enables to improve the analysis of the results of the lab-scale experiments and to design industrial-scale scenarios by simulation. The results of such simulations allow to estimate the economical interest and to perform environmental impact assessment. After presentation of the CEReS project objectives and main results, the paper describes the methodology used to build the simulator and define the scenarios corresponding to feasible process routes. The main results of the simulations are then presented with technical, economic and environmental point of views. INTRODUCTION Because of rapid technological innovations in the electronics industry, electronic waste represents the fastest growing waste stream in the world, especially in developing countries (Işildar et al., 2018). Meanwhile, the global copper demand is expected to go on rising in the future. As significant amounts of copper are present in end-of-life printed circuit boards (PCBs), it becomes a necessity to develop efficient copper recycling routes. Metal refining from e-waste is traditionally performed by pyrometallurgical processes. However, the hydrometallurgical processing of PCBs, which has been shown to be technically feasible at laboratory scale with a wide range of leaching reagents, could be a less energy intensive and more flexible alternative (Tuncuk et al., 2012). However, a large amount of leaching reagent is required to leach the metals from PCBs.

Jan 1, 2019

By Allan R. Punkkinen

Safe extraction of the valued ore resource in the deep levels of VALE Creighton Mine has progressed in a pillar-less fashion using vertical retreat, slot-slash and uppers retreat methods since the cessation of ?cut and fill? mining in the late 1980?s. Sequencing of the panel extraction and filling has been the key to successful exploitation of high stress orebodies at depth. In late 2010, discussions between the Operating Department and Creighton Ground Control revealed an opportunity to evaluate a trial primarysecondary sequence in the west end of the 400 Orebody at the 2340m horizon. To manage the trial primarysecondary project, a high level risk analysis and management of change was carried out to mitigate potential danger. As part of the requirements, an instrumentation project was conducted in the hanging wall and footwall bottomsills of the secondary panel and within the secondary panel itself. The extraction sequence was modeled with Map3D® software, confirming high stress levels with the advance of the primary panel. Enhanced ground support was installed based on modelling results. A key objective of the instrumentation project was to verify support system response to mining and to obtain knowledge in regards to the behavior of the stope. This paper describes the first time that this type of new innovative instrumented rockbolt technology had been used in a hard rock mining environment. Understanding of the physical deformation mechanisms of ground support in response to high stress conditions is the basis for an effective ground control strategy. The data played an important role in subsequent enhanced ground support system design at the mine and importantly, established the fact that the secondary pillar had not totally failed. Subsequent cavity monitor results helped establish that fact.

Jun 1, 2012

By J. E. Dutrizac, R. J. C. MacDonald, J. B. O'Reilly

"Sometime around 3000 B.C., primitive metallurgists working in the mountainous regions of Asia Minor bordering on the Black Sea (Pontus) produced a soft, easily fused metal today known as lead. It appears certain that the first metal was made by reductive smelting of galena, but whether this recovery arose by the accidental inclusion of galena in the stones of a fire hearth or whether it occurred as a consequence of simple pyrometallurgical experiments on a series of interesting ""stones"" will likely never be known with certainty. The properties of galena, high metallic lustre, great density and facile cleavage, must have excited the ancients, and such ""stones"" would have been the object of primitive testing111 - Shortly after the discovery of lead, the ancients found that the controlled oxidation of this metal at elevated temperatures yielded smaller amounts of a more interesting material, silver. Again, it is uncertain if the production of silver by primitive cupellation techniques was the result of a fireside accident or the consequence of a deliberate experiment, but the important fact is that silver was produced shortly after the discovery of lead. The techniques for making lead and silver spread gradually throughout the entire civilized world, likely as a result of both technology diffusion and independent rediscovery. The physical properties of lead could not have been overly attractive to the ancients, but silver was a different matter altogether. The gleaming white lustre and relative immunity to oxidation quickly assigned silver to the precious materials category, a status it still enjoys. In early times, argentiferous galena was inevitably processed only for its silver values; lead was generally an unwanted byproduct and was frequently discarded as litharge (PbO) during the cupellation process. The silver was eagerly sought, however, and resulted in considerable mining activity culminating in the famous Athenian silver mines at Laurium at the southern end of the Athenian peninsula."

Jan 1, 1999

By S. M. Bulatovic, D. M. Wyslouzil, K. R. Rawlings

"The suitability of a new organic reagent DS20 as a depressant for oxidized and carbonaceous pyritic lead-zinc ore from Nanisivik Mines Ltd. has been evaluated in the laboratory and in the plant.The depressant DS20 is a mixture of Lignosulphonate-Dextrin-Quebracho and was developed specifically for depression of highly oxidized and carbonaceous pyrite.The laboratory test work indicated that the poor metallurgy resulting from the oxidized ore could be improved to normal plant performance by the addition of the DS20 depressant with the existing plant reagents. The laboratory data suggested that lime consumption could be reduced when using DS20.In this paper, the development work and the plant trials with DS20 are described.INTRODUCTIONNanisivik Mines Ltd. treats approximately 2000 tonnes per day of lead-zinc massive sulphide ore, containing currently 1% Pb and 9% Zn. The concentrator operations have been described previously (1,2) and typical metallurgical performance is detailed in Table I.The concentrator flowsheet (Figure No. 1) and the standard reagent scheme (Table No. 2) demonstrate the relative simplicity of treatment of this coarse grained ore.A recently discovered satellite orebody - Area 14 - containing 2% Pb and 12% Zn was brought into production in October 1983. This ore had been oxidized to varying degrees by ground water; the pyrite mineralization was found to be very fast floating and a carbonaceous constituent present in higher than normal proportion also affected flotation. The simple high lime addition could not control the pyrite, and very low grade lead concentrates resulted; zinc metallurgy was also affected by this oxidized condition (Table 3)."

Jan 1, 1986

By S. N. Yu

Tele-operation manipulators applied in this paper are systems for the remote handling and management of pyroprocessing related facilities in an Argon cell of the KAERI (Korea Atomic Energy Research Institute). Generally, these kinds of systems are composed of a master-slave system and its peripherals installed along the wall of the cell, with the master transmitting the user?s own motion to the gripper directly. This study introduced various considerations and modifications to improve the remote handling performance. The analysis of an operator's ability using his/her own upper arm motion range while manipulating the MSM, and considerations of its manipulation margin and the related tool modifications are also included. Finally, the test results of several remote handling tasks are presented, and an adequate operation strategy for the tele-operation system of hot-cell type facilities is proposed.

Aug 1, 2013

By Charles S. Ney

"ZINC-LEAD REPLACEMENT deposits straddle the steep-sided valley of Kicking Horse River at a point three miles east of Field, B.c., in Yoho National Park. The Monarch orebodies extend into Mt. Stephen on the south side of the valley, and outcrop at two points, 1,000 and 1,200 feet above the valley floor. The Kicking Horse deposits are in Mt. Field, on the north side of the valley, and they outcrop 200 feet lower.The East Monarch outcrop is said to have been discovered in 1884 during construction of the Canadian Pacific Railway. The larger West Monarch outcrop, 700 feet west of the original discovery, was not reached till 1917 because of its nearly inaccessible location on the cliff face.The Kicking Horse mine was staked in 1906. Little development was done for several decades, and mining was not commenced till 1935.At the East Monarch, mining was commenced soon after location, and several thousand tons of ore were shipped prior to 1912. At this time a gravity concentrator was installed. This was operated till 1924, and a total of 42,000 tons of ore were mined, including about 10,000 tons from the West Monarch. The period from 1928 to 1935 featured flotation milling and the mining of 265,000 tons of ore, mostly from the West Monarch orebody. Intensive exploratory development was carried out in both Monarch and Kicking Horse from 1935 to 1946. Production from both mines in this period totalled 380,000 tons. From 1947 to the time of closure in 1952, considerable new ore was found in both mines and 185,000 tons were milled. Immediate possibilities for finding ore in the Monarch were considered exhausted. Kicking Horse orebodies are known to persist with a low grade of zinc. Total production from the two mines amounts to 842,500 tons grading approximately 7 per cent lead, 10 per cent zinc, and 1.2 ounces per ton silver."

Jan 1, 1949