Search Documents

By K. S. Raja, B. Pesic, S. Kshetri

"We investigated the electrochemical corrosion behavior of commercial permanent magnetic material (NdFeB alloy) in 0.1 M NaH2PO4 solution (pH:4.75) containing 0 – 1000 ppm of chloride at room temperature (298 K). The material was evaluated in magnetized and demagnetized condition with different surface preparations such as: Ni-Cu-Ni coated, uncoated (bare), and anodized (in fluoride containing ethylene glycol at 60 V for 15 minutes to form a thick nanoporous oxide surface). The nickel coated magnetic sample showed reasonable pitting corrosion resistance up to 100 ppm chloride addition. The uncoated samples showed passivity in chloride free phosphate solution. Chloride additions caused pitting and the pitting protection potential was equal to the corrosion potential with 100 ppm chloride addition. Demagnetization did not alter the electrochemical polarization. However, the passive film formed on the magnetic sample showed higher charge carrier density than the film formed on the demagnetized sample. INTRODUCTIONSintered NdFeB permanent magnets exhibit excellent magnetic properties such as large energy product [(BH)max > 450 kJ/m3], high saturation magnetization (1.6 Tesla), and high coercivity (1.2 – 2.08 x 106 A/m) (Sugimoto, 2011). However, the NdFeB magnets are prone to corrosion attack because of the presence of Nd-rich intermetallic phases, such as Nd4Fe (Jurczyk & Jakubowicz, 2000). Nd-rich and B-rich intermetallic phases are distributed in a matrix of Nd2Fe14B tetragonal ferromagnetic compound in a permanent magnet. Generally, several types of Nd-rich phases are present in the magnet with Fe:Nd ratios ranging from 1:1.2 to 1:7. The volume fractions of Nd-rich and B-rich (Nd1+xFe4B4 type) phases are about 10% and 7% respectively (Li, Ma, Li, & Wang, 2011) . Among these intermetallic phases, Nd-rich phase has the most active electrochemical potential. Therefore, dissolution of this phase occurs in preference to other phases by galvanic corrosion when exposed to moisture. Since Nd-rich phases are present at the grain boundaries of the Nd2Fe14B matrix, corrosion leads to disintegration of the magnet."

Jan 1, 2012

By Randy McMeekin, Chris Twigge-Molecey, J. Peter Blake

The business objectives of a metallurgical project determine targets and constraints, such as the range of products, production capacities, in-service dates, and capital and operating cost parameters. Permitting is usually left to the project team, as are decisions regarding site location, technology, and construction approach. Success requires an orderly methodology, represented in this book by front end loading (FEL) phases: FEL1 examines several alternative approaches; FEL2 ranks and eliminates less economically or technically attractive options; and FEL3 develops the preferred option to the point of major permit completion, with defined scope, schedule, and cost to submit for approval to proceed with implementation in FEL4. Working through FEL1, FEL2, and FEL3, the project definition improves, estimates become more accurate, and project risks are reduced. The project design basis at the end of FEL3 is the control document for project implementation in FEL4.

Jan 1, 2015

By K. .. Sadayappan

The increasing cost of selenium made the conventional low lead alloys such as EnviroBrasses not economically viable. Efforts were made to develop newer alloys without selenium for plumbing applications. Recently a new copper alloy, C89836, was introduced. This paper discusses the properties of the new alloy including mechanical properties at ambient and elevated temperatures as well as corrosion behaviour.

Jan 1, 2007

By J. Bouchard, M. Levesque, D. Georges-Filteau, P. Radziszewski, G. LeBlanc

"Grinding mills are infamous for their extremely low energy efficiency. This paper reports the results of an investigation that characterized energy outputs in industrial grinding mill circuits. It identifies and discusses the potential for recovering energy from grinding circuits. Agnico-Eagle Goldex Division, Mine Canadian Malartic, and New Gold New Afton Mine participated in the study by providing operating data for three semi-autogenous grinding mills and four ball mills. Results showed that on average, 79% of the supplied electrical energy was converted to heat absorbed by the slurry, 8% was lost through the drive system, and approximately 2% was transmitted to the ambient air. Only 9% of the input energy was actually used for grinding. The remaining 91%—wasted as heat—could potentially be recovered using suitable technologies or integrated energy management systems. This topic remains to be further investigated. ¦ KEYWORDS Comminution processes, Energy recovery potential, Grinding mills RÉSUMÉ Les broyeurs sont tristement célèbres pour leur rendement énergétique médiocre. Cet article présente les résultats d’une étude qui caractérise les rendements énergétiques des circuits industriels de broyage et examine les possibilités de récupération d’énergie dans les circuits de broyage. La mine Goldex d’Agnico Eagle, Mine Canadian Malartic et la mine New Afton de New Gold ont participé à l’étude en fournissant des données de fonctionnement pour trois broyeurs semi-autogènes et quatre broyeurs à boulets. Les résultats montrent qu’en moyenne 79 % de l’énergie électrique fournie sont convertis en chaleur absorbée par la pulpe, 8 % sont perdus dans le système d’entraînement et environ 2 % sont dispersés dans l’air ambiant. Seuls 9 % de l’énergie primaire sont, de fait, utilisés pour le broyage ; les 91 % restants (perdus sous forme de chaleur) peuvent potentiellement être récupérés à l’aide de technologies adaptées ou intégrées dans des systèmes de gestion de l’énergie. Cette question demeure toutefois ouverte. ¦ MOTS CLÉS broyeurs, potentiel de récupération de l’énergie, procédés de comminution INTRODUCTION Grinding is largely recognized as a very inefficient process; energy efficiency estimates range from < 1 to 2% (Fuerstenau & Abouzeid, 2002; Tromans & Meech, 2002, 2004) when comparing the input energy to that required for generating new mineral surfaces. Criticizing an “ill definition of the reference for the output energy,” Fuerstenau and Abouzeid (2002) proposed a “more meaningful baseline” would be “the energy for producing new surface area by the ¬mens.” Based on this reference, they concluded that “the ball mill is reasonably efficient energetically,” exhibiting an efficiency of approximately 15% for quartz."

Jan 1, 2019

By David L. Anderson

"The government o f Canada has, since 1981, been under intense political pressure to modify its foreign direct investment (FOI) regulatory regime(1). To date the government&apos;s response has been limited to administrative and ""cosmetic"" changes: substantive issues have been largely ignored(2). However, as long as the economy continues to flounder , the Foreign Investment Review Agency (FIRA), as it is presently formulated , will continue to be an easy target for government critics . This phenomenon, in conjunction with the virtual certainty of a federal general election within two years, suggests that changes to the FIR Act will be seriously entertained by the present government.Recent events indicate that if change s are made, they will likely entail the adoption of a special-sector approach within the existing framework of a general screening system(3). Since this approach is currently employed in Australia(4), it would seem to be appropriate, from a public policy perspective to study that country&apos;s experience in developing and operating such a scheme. In doing so, I shall focus on the mineral sector; the rationale for doing so is as follows. First, this sector served as the focal point of the Australian FOI regulatory debater(5), Second , with the exception of the oil and gas industries, the non-petroleum mineral sector is one of the few areas of the Canadian economy wherein the Trudeau government has adopted an explicit domestic ownership target(6). Third, the non-petroleum mineral sector is, undoubtedly, a prime candidate to be denoted a s a special-sector if such a framework were to be utilized by the Canadian government!"".Although international comparisons are fraught with danger , a Canadian/Australian comparison is particularly appropriate(8). Both countries have reasonably similar economic, political and social structures . Furthermore, as noted above , Australia is the only other western country which employs a general screening mechanism for FOI. In addition, it utilizes a special area approach ; within this scheme, an explicit target of a minimum of 50% Australian ownership of all new resource projects has been formulated and clearly promulgated to all of the relevant interest groups. This policy, broadly defined, has been in place for more than six years and during this time the Australian mineral sector has, by world standards, prospered(9). Hence, the Australian experience in designating the mineral sector as a key area within a general screening system, should be of interest to Canadian policy-makers."

Jan 1, 1984

By R. D. H. Wigmore

"The title of this paper probably sounds quite simple and self-explanatory. The problem, however, was not a simple one, and proved somewhat baffling and expensive over a period of years. After outlining the problem, and the methods which were used to overcome it, we will present our solution, or perhaps it would be more accurate to say the partial solution which we reached.We have in the cyanide circuit at Upper Canada two Dorr Single Tray Thickeners with 30 ft. diameter wood stave tanks 12 ft 4 1/ 2 in. deep. In the years prior to 1948, when the tonnage was 250 to 280 tons per day, two stage thickening was practised. As the tonnage was increased to 450, 500, and finally 560-600 the thickeners were used in parallel.Some settling problems were encountered, and in those days the means to combat these problems were very few. The only remedy was to dump in pounds and pounds of lime. Then along came a few reagents, and the writer remembers one in particular, - 11 Carboxel11 (carboxymethlycellulose). When water or solution was added to this reagent, the result was a gooey mass somewhat resembling tapioca. One drawback was that it stayed in this state, and didn't go anywhere. A method was finally developed of containing the mass (or mess) on a fine screen, and dissolving some of it was a fine spray of solution. The only thing the writer recalls was that it was not a very effective settling agent.Shortly after this time, along came the new flocculents, first a few, and then many, and our settling problems were over.But when the settling problem was solved at Upper Canada, some other problems were creeping up on us."

Jan 1, 1965

By M. Schwarze

SMS Meer GmbH with its COPPER PLANTS DIVISION produces a full line of systems and machines for the processing of copper. The product range includes: shaft melting furnaces, anode casting lines, horizontal and vertical casting lines, casting and rolling lines for copper wire rod and strip, cold pilger mills, planetary rolling mills as well as tube drawing equipment. The new designed shaft furnaces are the most economic way of copper melting. The CONTILANOD® system with hydraulic shear represents a breakthrough into higher production capacities and improved geometrical accuracy of anodes. The new generation of CONTIROD® lines with individual drives of rolling stands guarantee cost effective production of highest rod quality. A new horizontal continuous casting technology for the production of tube shells as feed stock for the copper tube manufacturing process ? directube® was developed and introduced into production. A first line for continuous vertical strip casting - called VERTICAST® - for higher production rates and improval quality of cold-rollable strips is in the final stage of commissioning. These innovative technologies increase product quality, reduce process costs and help for a wide use of copper in all sectors of life.

Jan 1, 2007

By Robert D. Brown

"On April 22, 1980, the Ontario government introduced a totally new incentive program for mineral exploration in the province to be effective September I, 1980. Replacing the former Mineral Exploration Assistance Program (MEAP) and also the assistance formerly provided to the mining sector under the Small Business Development Corporations Act, the new Ontario Mineral Exploration Program (OMEP) promises to offer a valuable benefit to certain eligible applicants.Unfortunately, the program is not without its shortcomings: the eligibility for grants or tax credits under the program is comparatively restrictive, and an October 1980 federal budget provision to amend income tax legislation would blunt some of the originally intended attractiveness of the grants and credits.IntroductionIn his budget of April 22, 1980, Ontario Treasurer Frank Miller introduced a new incentive program to encourage mineral exploration in the province.The Ontario Mineral Exploration Program (OMEP) replaces the Mineral Exploration Assistance Program (MEAP), which will be phased out by March 31, 1981. Exploration programs approved under MEAP will continue to qualify for incentives under that program, but will not qualify for OMEP."

Jan 1, 1981

By H. Higuchi

The Sumitomo Metal Mining Company Ltd. (SMM) started to produce electrolytic nickel at the Niihama Nickel Refinery in 1939. In 1992, the conventional matte electrorefining process was converted to the matte chlorine leach electrowinning (MCLE) process, which is currently in practice. SMM has mainly used two kinds of nickel matte as the raw material for the MCLE process. Treatment of new raw materials, which have different impurity contents from the original nickel matte, has become mandatory because of changes in the market. Therefore, the MCLE process has been required to increase its flexibility to treat the different impurity contents in the new raw materials. An increase in the capacity for iron removal is included in such requirements. A new iron removal circuit in the MCLE process, based on a process development study, was recently installed. The iron removal circuit is in operation, and efforts are currently underway to optimize the performance of the circuit by changing the present operating parameters. In addition to the removal of the iron, the application is also expected to improve the nickel recovery. The outline of the new circuit and the current iron balance in the MCLE process are described in this paper, together with the effect of the circuit on iron treatment capacity.

Jan 1, 2006

By D. Purdie

"This paper aims to remind researchers, designers, operators, and managers about the benefits of seeding in the design of precipitation stages in their flowsheet. Including a high density solids (HDS™) process encourages the precipitating solids to form on the surface of existing precipitated particles. This paper discusses the application of the HDS technology at Kennecott Smelter, where the authors have witnessed significant improvements in settling and filtration rates. The authors have also applied this technology at various smelter bleed treatment plants worldwide with similar improvements in precipitation and filtration rates. HDS is a registered trademark of De Nora Water Technologies. RÉSUMÉ Cet article a pour objectif de rappeler aux chercheurs, aux concepteurs, aux exploitants et aux administrateurs les avantages de l’ensemencement dans la conception des étapes de précipitation de leur schéma de traitement. L’introduction d’un procédé des boues haute densité (procédé HDS™, de l’anglais high density sludge) encourage la formation de substances solides précipitantes à la surface des particules précipitées existantes. Cet article porte sur l’application de la technologie HDS à la fonderie Kennecott, où les auteurs ont observé des améliorations importantes au niveau de la vitesse de sédimentation et de filtration. Ils ont également appliqué cette technologie à diverses usines de traitement des rejets liquides des fonderies dans le monde entier, et ont constaté des améliorations similaires en termes de vitesse de précipitation et de filtration. Le procédé HDS est une marque de commerce déposée du fabricant De Nora Water Technologies.INTRODUCTION In 1966, the lead author worked as an assistant smelting metallurgist for the Tsumeb Corporation Limited copper and lead smelter in Tsumeb, Namibia. The smelter produced copper and lead, as well as cadmium and arsenic trioxide as byproducts. The cadmium was concentrated in the lead blast furnace off gas dust, and was collected by a baghouse. The baghouse dust was leached with dilute sulfuric acid (H2SO4) in a batch process. The iron and arsenic in the solution were oxidized with potassium permanganate (KMnO4) and basic ferric arsenate (BFAS; Fe(AsO4)x(SO4)y(OH)z·wH2O) was precipitated using milk of lime. The cadmium was cemented from the purified solution using zinc dust."

Jan 1, 2018

By S. Akhlaghi

In many electronic/optoelectronic devices, interaction between the metal stack and solder is undesirable. If a reaction happens, a nonuniform joint containing spikes and voids is likely to form and as a result the heat dissipation deteriorates significantly, which in turn, leads to the degradation of the bond. In the present work the interaction between Ti/Mo/ Au metallization system, which was sputter deposited on AlN substrates, and Pb-Sn solder was studied by using scanning electron microscopy (SEM). Also, an EDX system was used to trace the changes in chemical composition of the layers after solder tests. The microstructural examinations show that the Ti and Mo layer from the Ti/Mo/ Au metallization system are not impermeable enough and thus Ca from the surface of the substrate moves all the way up to the interface of Au/Mo and forms an intermetallic at the interface, which grows over time.

Jan 1, 2006

By Robert B. Wickham

"American Barrick has always balanced its aggressive operating approach with a conservative financial strategy. In fact, what enables their mining team to pursue such aggressive plans with confidence is the conservative financial strategy adhered to by the company. These policies are built on a prudent mix of gold linked financings, equity and gold price hedging.This paper outlines these policies and focusses in particular on American Barrick&apos;s gold price hedging program.IntroductionThe company&apos;s balance sheet at the end of 1990 clearly shows the wisdom of its conservative policies. Total assets have grown to over US$1 billion; cash has grown to US$312 million and shareholders&apos; equity to US$645 million. All amounts included in this paper are quoted in U.S. dollars. Increased gold production and an effective gold price hedging program also combined to produce record income from operations, earnings and cash flow in 1990.The first half of 1991 is also indicative of the benefits of the company&apos;s conservative financial policies. Increasing production, together with its comprehensive gold hedging program, has generated increased earnings, even in a period of falling gold prices.All year-over-year numbers for the first six months are up. Gold production was 36% higher; earnings of $40.2 million $ 0.30 per share - were 46% higher than 1990.Barricks revenue continued to increase despite gold prices remaining unchanged during 1990. Barrick&apos;s hedging policy protects the company from falling gold prices on the basis that the upside looks after itself. Their hedging program - including various goldlinked fmancings - enabled Barrick to realize an average price of $437 per ounce of gold sold in 1990, compared with the Comex average gold price for the year of $384 per ounce."

Jan 1, 1991

By K Komori

Naoshima Smelter and Refinery has treated shredder residue and incinerator fly ash in Japan since 2003. As a highlight, a new incinerating and melting furnace, as well as fly ash washing treatment plant were newly constructed for pre-treatment of shredder residue and fly ash respectively, and the pre-treated materials are ultimately treated in the existing Mitsubishi continuous copper smelting and converting process line. Since wastes such as shredder residue tend to vary in size and in shape, and contain some chlorine, the installation of a new pre-treatment line was required. The combination of the new pre-treatment line with the existing Mitsubishi Continuous Copper Process line has created a highly efficient and environmentally friendly system for recovering and recycling of valuable metals that previously used to be sent to a landfill. This paper reviews the approach that Naoshima took to establish its current recycling business strategy.

Jan 1, 2007

By Wencheng Gao

An attractive way to beneficiate magnesium chloride and aluminum chloride is to prepare Mg-Al spinel, an excellent refractory material. Mg4Al2(OH)14?3H2O, the precursor of spinel, can be prepared using a co-precipitate method from aqueous MgCl2-AlCl3 solutions. The co-precipitation process of magnesium-aluminum from acidified chloride solutions by using NaOH or NH4OH as base neutralization agent was studied. Co-precipitation was conducted from different mixed solutions ? at initial CAl=0.0625M and Mg/Al molar ratio from 0.5 to 10, the temperature range from 30 to 90 °C. The effect of other parameters, including base type, method of base addition, base addition rate, aging time, background electrolyte and concentration were also investigated. The co-precipitation process was monitored by potentionmetric(pH) measurements. The experimental pH curves were characterized by two platforms separated by a steep jump in pH at Mg/Al molar ratio 0.5~6. The first platform was centered at about a pH of 3.8 and the pH of second platform was varied with different conditions. When the Mg/Al molar ratio was up to 6~10, the first platform in pH was almost disappeared. Furthermore, the shapes of pH curves were also affected by base type, base addition rate and method of base addition. Experimental results showed that the first platform in pH was connected with Al precipitation, and the second platform was involved with Mg. The final co-precipitates were characterized by XRD, TGA-DTA, particle size analysis, SEM and TEM. We found both Mg/Al molar ratio and temperature proved to be the key parameters controlling the formation of Mg4Al2(OH)14?3H2O phase. At solution Mg/Al ratio=0.5~4, the main precipitate phase was Bayerite (Al(OH)3) admixed with Mg4Al2(OH)14?3H2O; at Mg/Al ratio=4~6, the main phase was Mg4Al2(OH)14?3H2O admixed with some Mg(OH)2; while from Mg/Al ratio=6~10, the systems were mixtures of Mg(OH)2 and Mg4Al2(OH)14?3H2O.

Oct 1, 2011

By M. S. Alam, Jae-Chun Lee, M. Tanaka, K. Koyama

Extensive research work is being carried out at AIST for developing energy saving green technology for base and precious metals recovery. In the present work, a new flowsheet is developed for copper recycling from waste electronic circuit board where copper was recovered by leaching followed by solution purification and direct electrowinning of Cu(I) from ammoniacal alkaline solution. In this new technology, power consumption in EW circuit was greatly reduced. This paper describes the overall process with an emphasis on different aspects of solution purification where impurities were selectively removed by cementation and solvent extraction techniques under nitrogen atmosphere.

Jan 1, 2004

By Meifeng Zhi, Yuqing Niu, Xixin Chang, Fengqi Zhao, Weimin Qiu, Hao Wang, Zhenqian Wen, Zujun Shu

An applicable Eluex process was developed for acid in-situ leaching (ISL) uranium mine in Bayanwula. In this process, uranium was adsorbed with strong base anion resin from the pregnant solution, then the loaded resin was eluted by sulfuric acid. After D2EHPA extraction, the concentrated eluate was enriched, and the loaded organic phase was stripped by sodium carbonate. The yellow cake was obtained by sodium hydroxide precipitation at last. The uranium concentration in the loaded strip solution was 52.8 g/L. Parameters of the process were determined, and the impact of the Eluex process in underground leaching was also investigated. In industrial design, 95% of raffinate went back to elution and 5% back to in-situ leaching. No significant effect on uranium leaching or resin adsorption was found.

Jan 1, 2020

By P. Wanjara, M. Xiao

During fusion welding of aluminium alloys, the avoidance of defects (such as porosity, oxides, hot cracking, undercutting) as well as the ability to optimize the microstructure-property characteristics in the assembly are critical for the stringent manufacturing specifications in the aerospace industry. In this work, aluminium alloy (AA) 2024 was electron beam welded autogenously as part of a study to determine the influence of parametric conditions on the characteristics of the heat affected and fusion zones to obtain optimal welding conditions. In particular the evolution in the weld geometry, microstructure and mechanical properties were examined as function of the processing conditions, including beam current, beam focus, beam oscillation, linear heat input and welding speed. For optimized parametric conditions, microstructural examination of the joints revealed narrow fusion and heat-affected zones comprising of dendritic structures without the occurrence of defects that enabled a maximized joint efficiency.

Jan 1, 2006

By F. Rosenblum, P. Spira

"Self-heating of broken sulphide ore or waste rock underground can lead to ignition and cause serious problems in a mine operation. An extensive study has demonstrated that it is caused by oxidation of certain species of pyrrhotite. Self-heating was found to take place in two stages, first progressing from ambient temperature to 1000C with exothermic formation of elemental sulphur in the presence of moisture and oxygen, and proceeding to a second stage in which the sulphur oxidizes to SO2. Ignition may eventually follow. An apparatus was developed to assess the propensity of sulphide rock to self-heating and the potential for hazardous behaviour. The effect of temperature, time, rock size, and surface treatment with chemicals is presented. On the basis of these results, possible approaches for preventing a runaway reaction are suggested for further investigation.IntroductionThe oxidation of sulphide ore, waste rock or tailings backfill, which may cause hazardous conditions underground through heating, oxygen depletion and, in some cases, fire, is well documented (Farnsworth, 1977; Ninteman, 1978; Rosenblum et al., 1982; Reimers, 1987). The self-heating mechanism, nevertheless, has not been satisfactorily explained. The onset of heating from ambient temperature, in particular, has not drawn the attention of researchers. In the course of a previous study (Rosenblum et al., 1982) aimed at finding a method to assess the hazard from using sulphide tailings as backfill, the authors developed an apparatus to measure self-heating rate under controlled, near ambient conditions. This has since provided decisive information in backfill investigations in the Noranda Group.The test methodology devised for tailings failed to predict self-heating in a broken waste rock known to be active. Upon repeated testing, however, a freshly crushed sample began to exhibit appreciable heating and oxygen uptake (Fig. I). After 14 tests, the self-heating rate reached a plateau of about 4O°C/h and then fell progressively to < 5°C/h after 30 tests. It was hypothesized that weathering in the presence of moisture and oxygen during testing had caused the onset of self-heating. Active tailings, on the other hand, are exposed to natural surface oxidation and need not be weathered to show heating. Based on this finding, a new apparatus was developed capable of simultaneously weathering a sample of rock and monitoring its self-heating behaviour."

Jan 1, 1995

By M. Côté, H. Pépin, Y. Richer, C. Gingras

Rolls-Royce Canada has been nominated as a Rolls-Royce Center of Excellence for repair of fan blades in 2003. One of the challenges of the Rolls-Royce Canada Component Repair Center of Excellence team is to reduce cost and time of inspection while ensuring trace ability and quality of the inspection performed on the fan blades. In the context of the dimensional control process optimization, and following the positive conclusions of initial trials carried out in 2003, the technical authorities at RRC have selected the SPG data 3D(TM) technology as a development base for dimensional control programs. The main goal of this development initiative is to develop and support an inspection system to perform the dimensional control and inspection of different components at the Montreal Fan Blade Repair Center of Excellence. The final objective of the program is to build a server platform capable to support different inspection sites within the Montreal facility for the future. This paper presents the certification process of the technology according to the VDI-VDE 2633 certification standards and some results of the fan blade inspection program of the BR 710, BR 715 and TAY according to the JES 195 engineering standards specification.

Jan 1, 2006

By Q. J. Xu

In blasting sensitive areas, the use of traditional blasting for rock fracture is restricted. Soundless cracking technology has been presented to achieve rock fracture instead of blasting. However, when the diameter of a borehole is larger than 50 mm, it is very dangerous that the soundless cracking agent (SCA) will have a tendency to gush from the borehole, which also leads to cracking failure. In this paper, a new large scale borehole soundless cracking technology is presented, using a new enlarged drill bit and mechanical plugging, which could solve the hole gush problem. Experiments were made to measure the expansive pressure of the SCA working in boreholes of F40 mm and F100 mm. The difference between two sizes of cracking phenomenon was compared and analyzed to show that large scale borehole soundless cracking has larger expansion pressure and faster reaction speed than traditional soundless cracking. Based on the experimental data, finite element analysis was utilized to study the stress concentration and stress distribution between two neighboring large boreholes in several media during the cracking process. Using the data from experiments with finite element numerical simulation, the brittle material fracture condition was analyzed to design the parameters of the borehole mesh. With the theoretical analysis, the technological process and reference parameters of large scale borehole soundless cracking were proposed, including the borehole spacing, burden distance, depth of the borehole and so on. Then a single rock was cracked with the new enlarged drill bit and new plugging, and the results proved the feasibility of the new large scale borehole soundless cracking technology, which achieved the expected goal of improving the cracking ability and reducing the cracking time. This paper presents a new efficient rock cracking method for blasting sensitive areas, and which could apply to mining engineering, demolition engineering, excavation engineering and other engineering applications where there is a demand soundless and non-vibration fracturing of rock.

Aug 1, 2013