Search Documents

By Lesley Hymers

First Nations Natural Resources Youth Employment Program PDAC Mining Matters ? Charitable organization ? Provide education to students, teachers, and the public about rocks, minerals, metals, and mining ? Provide current information and offer exceptional educational resources that meet provincial Earth science and geography curriculum expectations First Nations Natural Resources Youth Employment Program ? Provide instructional development workshops for educators who are teaching Earth science and geography ? Since 1994, reached more than 400,000 students, teachers, industry representatives, and members of the public

May 1, 2009

By David deVries, James Rajith, Paul Mascrenhas, Nurzhan Dyussekenov, Lawrence Hanschar

Kansanshi Copper Smelter commenced operation in March 2015. The smelter features four Peirce- Smith Converters (PSCs) operated in a three hot, two blowing configuration. This paper describes some of the process automation and design features implemented to maximize operational and environmental performance. To ensure that the converters were easy to operate, efficient, and were protected in emergency situations such as power failures or loss of tuyere air supply a significant focus was placed on automated sequences initiated by “one button” operator commands or otherwise automatically by the Distributed Control System (DCS). Examples include: main converter roll-in and roll-out sequences; emergency roll-out in the event of power failure; and the charging sequences for reagents (silica and reverts). Other automated features configured for the PSCs were specifically aimed at maximizing converter capacity and reducing the environmental impact from fugitive emissions. These features include: “one button” in-stack charging; automated restriction of blowing rate based on the available acid plant capacity; and fully-automated control logic for the Secondary Ventilation System. In-stack charging allows anode furnace oxide slag to be poured into the PSCs while the converters are still blowing and still sending off-gas to the acid plant. PSC Secondary Ventilation control logic was configured to require minimum input from the operators while ensuring maximum utilization of the available draft from the ventilation system. Highly automated PSC controls contribute to high utilization, averaging 41.2 in-stack hours per day. INTRODUCTION Kansanshi Copper Smelter (KCS) is located near Solwezi at Kansanshi copper mine in Zambia's Northwestern province. The smelter treats concentrate produced at Kansanshi mine as well as Sentinel mine located 150 km west of Solwezi. Four Peirce-Smith Converters (PSCs) are installed at KCS. The nominal capacity of each converter is to treat 350 t of copper matte and produce up to 250 t of blister copper per batch. Normally three PSCs are hot, with two able to operate (produce off-gas), and the third converter on hot standby. The fourth converter is normally under cold repairs. The blister charge size is relatively low for the matte charged due to the unavailability of tank house or other high copper scrap.

Jan 1, 2019

By Ken Musgrave

"A program is described that helps managers and supervisors control maintenance more effectively. Work- order generation, preventive maintenance, repair parts inventory, planning and scheduling, reporting, analyzing costs, printing purchase orders and other functions are covered. Flexibility often permits integration with other programs such as payroll, cost accounting and materials management.The Role of MaintenanceMaintenance provides a service to allow the rest of the operation to do its job effectively. Its success should not be measured by maintenance cost alone, but also by its effectiveness in reducing downtime and maximizing production. It can make sense to spend more maintenance dollars if this results in an even greater contribution from increased production.The Cost of MaintenanceIn mining companies, maintenance costs can be as much as half of operating costs. Maintenance has generally not been given the management attention that an expenditure of this magnitude deserves."

Jan 1, 1986

By V. Vorontsov

Catalysts Mo-Ni-S were prepared by combining MoS2 and NiS in weight ratios 1:1, 1:2, 1:4 and 2:1, each of which was admixed with 5%wt Ag and 5%wt YSZ to increase three-phase boundary surface area of the electrode. For comparison catalysts comprising Co-Mo-S in weight ratio of 1:1 of CoS to MoS2 admixed with 5%wt Ag and YSZ and pre-sulfided NiMoO4 were made. The catalysts were examined for electrochemical oxidation of hydrogen sulfide in solid oxide fuel cells (SOFC) at 850°C temperature. The catalyst prepared from 1:1 (wt. %) NiS:MoS2 demonstrated highest performance. Current density up to 1,330 mA/cm2 and power density up to 300 mW/cm2 were achieved using pure H25 gas, which are the highest among the reported H2S-powered fuel cells ever published in the literature. Anode materials of different NiS:MoS2 ratios have been characterized by means of X-ray diffraction (XRD), simultaneous TG/DSC analysis and Neutron Activation Analysis (NAA). TG/DSC and NAA results show that addition of NiS and Ag increases fuel cell performance due to improved structure/integrity of the anode. It has also been demonstrated that MoS2 is a suitable anode material in H2S-powered SOFC, with high activity towards H25 oxidation and thermally and chemically stable up to 850°C.

Jan 1, 2005

By A. E. Cameron

The theory of atomic distribution of the stranger atoms in the space lattice of the solvent metal has been well developed by Rosenhain. It has long been known that the addition of one metal to another to form a solid solution increases the strength and hardness of the solvent metal. This increase is practically proportional to the amount of added substance up to the limit of solid solubility. To account for this increase in hardness and strength, Rosenhain assumes that the stranger atoms occupy positions on the solvent metal space lattice. Atomic attractions about the stranger atoms will not be the same as in the case of the pure metal, and there will thus be a disturbance of the orderly arrangement of the atoms on the space lattice, or a distortion of the lattice. Such a disturbance would interfere with the ease of slip along the planes and would thus tend to promote strength and hardness. Rosenhain notes that not only may there be a local disturbance of the lattice about the stranger atom but there may well be also a measurable change in the dimensions of the lattice as a whole. The relative amounts of local and general distortion of the lattice will depend upon the nature of the lattice itself. As Rosenhain says, "If the lattice is comparatively soft and flexible the distortion is likely to be largely local. In a stiff lattice, however, local distortion will be resisted and there will be a correspondingly increased general distortion."

Jan 1, 1927

By G. Banini

Prior to installation of High Pressure Grinding Rolls (HPGR) at PT Freeport Indonesia (PT-FI) a series of laboratory tests were carried out to determine the design parameters and also determine key performance indicators (KPIs) for the industrial unit. The design parameters derived from the lab test work were then scaled up to estimate the industrial capacity of the HPGRs to be installed. These parameters include specific power draw, specific throughput, and specific force, rolls speed, product size distribution and wear rate of the rolls. This paper compares the performance of the scale-up procedure against the installed industrial size HPGR. Overall, the specific throughput of the industrial size HPGR is higher by a minimum of 30% compared to the expected scale-up value. As a result of the high specific throughput, the specific power draw and grind sizes are below the scale-up expectations in the commercial application. The impact of these factors also contribute to a lower than expected wear rate on the industrial rolls. Installed rolls achieved a service life in excess of 18,500 hours relative to the target of 6,850 hours predicted from the laboratory testing.

Jan 1, 2012

By F. W. Wellmer

"This paper discusses the changing nature of reserve/consumption ratios, using data from Canadian operations and focussing particularly on copper.IntroductionStudies in world metal consumption and world metal reserves are done regularly by the U.S. Bureau of Mines, the German Federal Institute of Geosciences and Raw Materials, and other institutions. Formerly, on the basis of these data, the following figures were calculated:• a static lifetime of reserves-reserves at year end divided by the consumption of the previous year;• a semidynamic lifetime of reserves-reserves at year assumed constant growth rate.These figures were severely criticized because they were purely theoretical and did not consider the availability of the raw materials.Recent practice is to calculate reserve/consumption ratios (R/C ratios) for periods(1) or for different years(2,3) and to interpret the trend. For base metals, these R/C ratios are increasing (Table 1). This had led to the conclusion that today the relative availability of base metal reserves has increased as compared to 10 or 15 years ago(4,5) As there are normally numerous deposits for each commodity, the anticipated production rates of deposits are irrelevant to this conclusion as long as the statistical distribution of possible production rates does not change significantly.The above conclusion is only justified if the quality and the nature of the data base remain the same. This is certainly the case for the consumption data. It is also assumed for the quality of the reserve figures, which usually take into account only proven and probable reserves. For the nature of the reserve figures, however, this does not seem to be true.Undoubtedly, the reserves increased in absolute terms between 1966 and 1978. To put the absolute reserve figures into perspective, it is common, as said above, to compare them with the mine production, which increased in the free world between 1966 and 1978; e.g. for copper by 40%, for Pb by 17% and for zinc by 36%. However, the reserves are also influenced by other factors, such as average size of the mines, changes in the grade of the mined ore, price-to-cost relationships and the like.The purpose of this paper is to examine the nature of the reserve figures in more detail. Because the completeness of mining data published in Canada is rather exceptional, Canadian .data serve as an example and it is assumed that the conclusions can be extrapolated to other mining countries or at least to those with free market systems."

Jan 1, 1981

By Ursula M. Franklin

Old iron nails are one of the most common objects which entice the general public to ask questions about the history of metallurgy. There is a lot of history in old nails - history of the manufacturing industry, and social and economic history. Nails, therefore, are fine teaching tools; whether students have to acquire metallurgical skills or explore the structure and properties of wrought iron, whether they want to look into the history of inventions and the development of machinery, studying nails tells a story better than any teacher or any book. I have used this approach often and the following note is based on several student projects, particularly the work of Carmina Herrero and Vicky Marchant. Nails, those essential metallic fasteners, have long been with us. Their size, shape and design is basically a compromise between the makers' ability to control and manipulate material and the demands of the intended application. There were copper and bronze nails in antiquity, but in this paper I want to deal only with iron nails. In Rome, iron nails were common, and Cleere carried out the fine metallographic investigations on a large stock of nails recovered from a Roman fort site in Scotland. Those nails were hand forged; sorting them at the site on the basis of length, shape of head and shape of shank (in cross section) indicated that there seemed to have been some nail standardization. It appears that the Roman smiths used a series of heading dies starting with a 1/s-in. size. Each successive size increased by approximately 1/16-in. The metallographic inspection of the microstructures of the nails showed that the smaller nails were made in the one operation; i.e. both the tapering and the formation were accomplished on the heated rod without reheating. However, in the case of the larger nails, the nail had to be reheated for the tapering after the head had been forged. Most nails were tapered on all four sides of the shank and the shanks were square in cross section; only one group had rounded shanks. Most heads were flat disks, but in one group the heads were pyramids and another group had conic heads. Figure 1 shows the procedure used to produce the pyramidal heads. Obviously, Roman nail making was sophisticated and each nail design was meant for a particular use.

Jan 1, 1999

By H. Tetu, F. Pells

"The copper-molybdenum property of Brenda Mines Limited is located in the Okanagan district of British Columbia, approximately 25 miles west of Kelowna. The Okanagan Valley is a resort and fruit-growing area, and therefore pollution control measures are more stringent than in some remote areas.The Brenda plant began production in April 1970 and is operated at a rate of 24,000 tons per day. The plant site is located at an elevation of 4,800 feet, which is approximately 3,600 feet above the level of Okanagan Lake. The site is in the Okanagan drainage basin.The major consideration in the design of the system was the prohibition of any downstream discharge. It was therefore necessary to redaim as much water as possible and to minimize the addition of fresh water to the system. The maintenance of a water balance is of critical importance.This paper will outline the major design criteria for the systems and the site investigations which were carried out. The design and construction of the facilities will be de-scribed and current operating experience will be outlined."

Jan 1, 1971

By M. M. O?Brien

THE SULLIVAN MINE The Sullivan mine of the Consolidated Mining and ? Smelting Company of Canada, Limited, is situated at Kimberley, B.C., nineteen miles from Cranbrook, a divisional point on the Crowsnest Pass branch of the Canadian Pacific railway. Production started on a small scale in 1900, and in 1914 the mine became the largest lead producer in Canada. In 1925 it was the largest single producer of lead and zinc in the world. Since operations commenced, 4,800,000 tons of ore have been produced from stopes and 170,000 tons from development. At the present time, ore is being mined at the rate of 1,100,000 tons per year, with a yield of about 200,000 lb. lead, 110,000 lb. zinc, and 4,000,000 oz. silver. The town of Kimberley is easily accessible by road as well as by rail. The altitude at Mark creek, a tributary of the St. Mary's river, is 3,700 feet. To th'e north of the creek, Sullivan hill rises to a height of 6,100 feet, and it is on the southern slope of this hill that the mine is located. Sullivan hill is in the Purcell range, which rises between the Rocky Mountain trench on the east and Kootenay lake on the west. It thus lies within what is commonly referred to as the East Kootenay district.

Jan 1, 1926

By R. Panchadhara, P. A. Gordon

"A non-local formulation of the classical continuum mechanics theory called peridynamics is used to study driven dynamic fractures in the near wellbore region. The controlled application of pressure on the inner walls of the borehole can create multiple fractures that initiate from the borehole and propagate radially outwards. The number of fractures and their final length is primarily controlled by the loading conditions and the in-situ stress state. It is the objective of this study to use a novel numerical technique called peridynamics to investigate: 1) the influence of loading conditions on the fracture pattern, and 2) the effect of in-situ stress anisotropy on fracture propagation. In peridynamics, the momentum equation from the classical theory of solid mechanics is replaced with the integro-differential momentum equation of peridynamics. As a result, discontinuities in the body, such as fractures, occur spontaneously. The material is represented by a continuum body with material points that interact non-locally with all other points within a specified distance. Fractures evolve using a damage evolution law, wherein, damage at any point is represented as the ratio of the number of broken bonds in the current configuration to the total number of bonds in the undeformed configuration.Simulations are performed on simplified test cases and the results are compared to relevant experimental and numerical studies found in the literature. It is shown that the loading rate significantly influences the number of fractures initiated from the borehole as well as their extent. Low loading rate produces fewer fractures, whereas, high loading rates produce longer and a greater number of fractures from the borehole. The numerical method successfully predicts the fracture pattern obtained from a wide range of loading conditions. Predictions also indicate that the resultant fractures are shorter when in-situ stress is applied. Numerical results show that the fracture extension is largest in the direction perpendicular to the minimum compressive stress for the range of loading rates used in this study."

Jan 1, 2015

By O. Lashkari, A. Charette, R. Ghomashchi

Conventional casting at low pouring temperature was employed to produce semisolid metal, SSM, billets of A356 Alloy. The deformation behavior of the as-cast SSM billets was studied using parallel plate compression viscometry. The compression tests were carried out at different applied pressures, and fractions solid. The rheological studies were conducted assuming the SSM slurry behaving like Newtonian and non Newtonian fluids respectively. The calculated viscosity numbers confirmed pseudoplastic behavior of the SSM billets and were correlated to fraction solid and shear rate proposing the following empirical equation which is valid at low shear rates, less than 0.01 s-1, and fraction solid of0.33-0.46: 0 log77 =5.56-l.38fs -(l.56fs +0.14)logy Aluminium 2006 45th Annual Conference of Metallurgists ofCIM Montreal, Quebec, Canada Edited by G. Dufour, F. Paray and J. Tessier 0.33<fs<0.46

Jan 1, 2006

By L. Lamothe, C. H. The

"Pilot precipitator tests were conducted at Noranda&apos;s Horne Smelter in late 1978 to evaluate methods of improving converter dust collection efficiency. A bout 35 Nms/min. of converter off-gas were isokineticatly diverted from the converter flue to the pilot precipitator leased from Flakt (Canada) Ltd., consisting of three fields, one transformer-rectifier set per field and 77-m2 total collecting plate area. The effects of gas volume flow rate and conditioning the gas with sulphur trioxide and/or additional moisture were tested. II was found that gas flow rate and moisture level had the most pronounced effect on collection efficiency. Based on a techno-economic assessment of different options for improving converter Courell efficiency, waffle hoods and water sprays were installed on the converters to reduce air infiltration and increase the moisture level in the gas.BackgroundThe Horne Smelter of Noranda Inc. is situated in northwestern Quebec and, since the closure o f the min e in 1976, has been operating as a custom smelter. The concentrates treated at the smelter come from various mines with mixed sulphide ores , many o f them containing significant amounts of lead and zinc which makes dust collection in electrostatic precipitators mo re difficult than normal.As part of a continuing program on reducing smelter dust emissions, the No . 6 Cottrell was installed in 1972 up stream of Nos. 2 and 4 Cottrells (in parallel) in a n attempt to improve dust collection by increasing the over- all precipitator capacity ( Fig. I). However, it has never per formed a t its designed efficiency o f 94%. The average efficiency established in various test s was in the range of 60 – 65%."

Jan 1, 1985

By P. Nayak

"Comminution is an energy intensive and expensive process consuming approximately 40-50% of the total processing costs in a mining operation. This process poses an even greater challenge with gold ores due to their low elemental concentration and small particle size. Over 99.9% of the ore fed to the mill is waste which must be removed during the ore processing stage. Preconcentrating the Run of Mine (ROM) ore before feeding the mill will result in significant cost savings. In partnership with Sacré-Davey Engineering, Agnico Eagle Mines Limited identified this opportunity and is currently evaluating the implementation of sorting technology to preconcentrate the ore or upgrade the waste material at its operations. This paper will discuss the steps adopted by Agnico Eagle in the evaluation and installation of sorting technology at its operations. Since the Company has a large portfolio of operations, the first step in the project was to shortlist the operations that had the highest probability for successful application of the technology. Following this, the top three operations were selected for bench scale evaluation. The projects which showed the most economic potential were then considered for detailed evaluation and pilot plant installations. This paper provides an insight into the methodology followed by Agnico Eagle and Sacré-Davey in the evaluation of the technology.INTRODUCTION The benefits of ore sorting technology are being increasingly understood by the mining industry today. The application of ore sorting in gold mining is attractive due to the nature of the mineral distribution. The presence of high value minerals distributed in an extremely small mass of the ROM ore creates a tremendous opportunity for preconcentration with ore sorting. Since Agnico Eagle currently has a portfolio of eight operating mines and numerous development projects and exploration properties, the challenge was to identify the deposits which had the most favourable mineralogy and grade distribution for successful ore sorting. The success of ore sorting is mostly based on the minerals present in the deposit and the grade distribution. The minerals signify the amenability of the deposit for ore sorting and the kind of sensing technology to be used. On the other hand, the grade distribution demonstrates the amount of material that can be rejected without losing value. In order to understand a deposit’s characteristics, it is important to examine the sample’s behaviour with various sensors and then assay it to know its actual value. It is a common practice in the mining industry to document assay value of drill cores and/or material feeding in and out of the mill. However, those VALUES (are insufficient to understand the grade variability on a granular basis. To capture the ore variability in very high resolution and significantly improve the selectivity of the material feeding the mill, it is vital to assay the samples on a rock-by-rock basis, as this is the level of resolution which will be examined by the ore sorter during sorting. A careful and elaborate procedure was followed in evaluating the technology at Agnico Eagle’s operations which is discussed in this paper."

Jan 1, 2019

By D. T. Aikens, R. Gaudreault

"This paper summarizes structural repairs carried out on a marine wharf consisting of six 13.7 m by 13.7 m reinforced concrete cribs linked together by five 14.6 m long beam spans. As a result of problems during original construction and twenty years exposure to severe weather conditions, the deck support system between the cribs required major restoration work. In particular, some of the beam seats under the crane rail supports had marginal bearing area to support the structural loads. Faced with closure order for the wharf which is required to bring in raw materials to the plant and a long outage to make repairs as stipulated by Ports Canada (owners of the structure) alternate means of making the required repair were examined.The method chosen allowed the work to be done much more quickly, at lower cost, without taking the wharf completely out of service. The badly deteriorated seats were rebuilt using epoxy grout, tapered sole plates and a positioning jig."

Jan 1, 1988

By Nigel J. Cook

"Detailed mineralogical examination of gold-bearing rocks, ores, concentrates and other samples should be considered an integral part of any study of a deposit for which exploitation is being planned. Adequate mineralogical study, although time consuming and often costly, can significantly improve understanding of the mineralization, can help to optimize the results of any metallurgical testing and can be of great value in case of potential trouble-shooting. The advantages and disadvantages of various examination techniques are discussed with reference to a number oj mineralogical studies oj Canadian gold-bearing samples.IntroductionVarious authors, notably Gasparrini (1983), Harris (1989) and Henley (1990), have stressed that mineralogical study of gold ores is critical to successful and efficient beneficiation. Only in cases where diagnostic cyanide leach testing is successful can detailed mineralogical examination be disregarded. Such examination of gold-bearing rocks and metallurgical products is all too often neglected because the methods involved are believed to be time-consuming, costly, and may carry a considerable degree of inaccuracy. Commonly, bulk metallurgical testing is, carried out without prior or concurrent mineralogical examination, causing the results of the testwork to be difficult to interpret, or in some cases, misleading. This, in turn, may lead to> significant delays to the project at the feasibility stage or mean that understanding of the sample is limited, preventing the introduction of prudent modifications at a later stage if problems arise. Mineralogical studies may guide the successful implementation of a metallurgical test program."

Jan 1, 1990

By A. M. Nordale

Let us first trace a line, mentally, across Alaska and Yukon, starting at a point in the west slightly south of the delta of the Yukon river and from there continuing eastward, loosely following the 63rd parallel of latitude until we have passed beyond the eastern border of Yukon. We will make two pronounced digressions southward to include the greater parts of the Iditarod and Tanana River valleys. That visualized line roughly defines the southern boundary of permafrost. North of it lies a vast region, fully three-fourths of the area of the two territories, which includes Seward peninsula, the great Yukon River basin, and the tractless wastes of the Arctic. During some frigorific cycle in the distant geological past, the ground there was frozen to a depth of many hundreds of feet. How deep the frost actually penetrated is not known, but it has been found to exceed three hundred feet in many places. Nature afterwards provided a perfect insulating cover in the form of heavy moss and dense grass, which has protected the ground from the heat of the sun&apos;s rays during the intervening ages. This frozen condition has always been accepted as something indigenous to the North and little thought was given to -it until recently, when the United States Government and, I believe, the Canadian Government, began extensive studies of it, particularly in respect to its effect and bearing on the development of the great oilfields of the Arctic. Within this large region and but a short distance south of the Arctic circle are the three principal producing placer gold fields in the sub-arctic, whose hubs centre at Nome and Fairbanks in Alaska and at Dawson in Yukon Territory. The geological structure and history of the gold-bearing deposits of Dawson and Fairbanks are very similar and probably closely related. They are typical placer deposits produced by stream action during periods of erosion and inundation and subsequently covered with a thick layer of fine, powdery silt mixed with decayed vegetation which, locally, is termed &apos;muck&apos;. The depth of muck varies from less than 10 to more than 250 feet, with the greater depth near the lateral edges of the valleys. The gravel underlying it is medium in size, well rounded, and composed mostly of quartz and schist. The proportion of sand or fines is approximately 40 per cent. No large boulders and little clay are found, for those districts, as well as that of Nome, have not been subjected to glaciation. The most common bed-rock found is either decomposed or hard schist, but infrequently it is slate, quartz, diorite, or a porphyry. The vertical concentration of the gold is invariably on bed-rock and in the lower few feet of gravel which overlie it. The horizontal concentration or paystreak is roughly parallel to the trend of the valley but does not ordinarily coincide with the course of the present stream. The width of the paystreak usually expands from a few feet at the head of a creek to several hundred feet near its mouth.

Jan 1, 1947

By Kr. N. Karparov

Measurements made with high precision GPS landmarks and geotechnical radar Reutech MSR- 300 associated with the observed movements in the north face of Assarel Mine, where on a horizontal distance of 50 m, 2 groups of landmarks indicated different deformation behavior. Measurements are made in order to confirm the applicability of the radar system in regions of complex geotechnical conditions. The standard deviation of each landmark is used as an accuracy standard between the separate measurements of the deformation vectors made by the high-precision GPS system for each landmark. A very good correlation between the displacement vectors can be seen based on the measurements made with the high-precision GPS system and the measurements made by the radar system MSR-300. Geological, engineering geological and hydro-geological conditions of the area of concern are discussed in this paper. The measured deformations and the FLAC/SLOPE analysis show similar results. In the paper is discussed their local character and their sensitivity to other geotechnical and hydro geological conditions.

Aug 1, 2013

By David J. Kerr, Robert Mason

"From1927 to1989, the Hornemineproduced53.7 Mt of ore grading 6.1 g/t Au and 2.2% Cu from two large volcanogenic massive sulphide deposits composed primarily of pyrrhotite, pyrite and chalcopyrite. The ore bodies were hosted by a package of chlorite-sericitealtered epiclastic rhyolite tuffs which were deposited in a narrow palaeo-graben located on the flank of a major felsic volcanic centre. M ineralizingfluids percolated upward through the permeable footwall rocks and were further focussed along syn-volcanic, graben-bounding faults. Sulphides were deposited by a process of sub-seafloor replacement of the rhyolite tuffs.Gold-copper-(zinc) mineralization, including ore zones mined between 1985 and 1989 as the REMNOR ore zones, is present throughout the 900 m of felsic volcanic stratigraphy at the Horne. All the deposits were formed by syn-volcanic hydrothermal processes active during felsic volcanism. There is no evidence to indicate that any economic gold mineralization was introduced by a post-volcanic hydrothermal episode.RESUMEDe 1927 a1989, /amineHorneaproduit53.7 Mt de minerai avec une teneur de 6.1 g/t Au et 2.2% Cu provenant de deux grands amas de sulfures massifs volcanogeniques comprenant esentiellement de la pyrrhotite, de la pyrite et de /a chalcopyrite. Ces gites font partie d'une séquence de tufs rhyolitiques epiclastiques chloritises et sericitises qui ont ere déposes dans un paleo-graben étroit situe sur le flanc d' unimportant centre vo/caniquefelsique.Lesfluides mineralises ont circule de bas en haut a travers /es roches perméables sous-jacentes; ils ont été également canalises par les failles syn-volcaniques en bordure du graben. Les sulfures se sont déposes par remplacement des tufs rhyolitiques immédiatement et sous /e plancher océanique.Les zones minéralisées en or et cuivre (±zinc) - y compris celles qui ont ere exploitees au cours de l’opération Remnor (1985-1989) - se retrouvent, sans discontinuité, à travers les roches volcaniques felsiques dont l' epaisseur atteint 900 m. Ces gites se sont formes par le biais d' un processus hydrothermal qui ag issait pendant le volcanisme felsique. II n'y a aucune évidence de minéralisation aurifère d'importance économique qui soit postérieure a l' activité hydrothermale syn-volcanique."

Jan 1, 1990

By Robert White

?Introduction of BMS?Paste fill generalities?Development through paste?Development through rock fill?Conclusion ?Brunswick mine is operated by Xstrata. The mine has been in operation since 1964 and produces around 10 000 tons per day of ore containing (in order) zinc, lead and silver? The ore body consists of close to ten sub-parallel massive sulfide lenses. The length of the ore body is 1200 m with a width of up to 200 m. From the surface, the ore body extends to a depth to 1200m ?There is 100 km of active drifts for a total 400 km ?The mine is divided by 7 levels and 23 actives sub levels

Feb 1, 2008