Search Documents

The Cooperative Research Centre for Mining Technology and Equipment (CMTE) is funded by the Commonwealth Government, by its mining research members Ñ the Universities of Queensland and Sydney and the CSIRO1, and by its industry members Ñ BHP Coal, RioTinto R&TD, Hamersley Iron, Mining Technologies Australia, Pasminco, Shell Coal, WMC Resources, Advanced Mining Technologies, and Aberfoyle. The Centre conducts work aimed at improving the competitiveness of the Australian mining industry. The current work is focused in four areas: new mining and drilling systems, geological sensing, automation, and equipment maintenance and reliability. This paper describes much of the work in these program areas that relates to metalliferous mining.

Jan 1, 2001

By D. O. Tansey

This paper will describe the mechanisms involved in delay blasting and how they are applied with the use of D.S.B. It will examine the control of potential damage resulting from detonations, and show how good fragmentation and efficient recovery of this material blasted can be achieved

Jan 1, 1979

By Nader Golchinfar

The V-shaped breakout zones around excavation boundary have been captured by a variety of numerical methods such as FEM and DEM methods and failure criteria such as linear Mohr-Coulomb and non-linear Hoek-Brown failure criteria. Diederichs (2007) used Hoek-Brown parameters in his spalling parameter approach; however, it is convenient to use the Mohr-Coulomb failure criterion in numerical modeling because the material parameters can easily be determined from triaxial tests. It is shown in this study that when peak and residual strength parameters as well as dilation angle are properly defined, the brittle Mohr-Coulomb failure criterion can be used to model depth of failure near underground excavations satisfactorily.

Jun 1, 2012

By J. B. Heslop, D. S. Bubar

"The Gondor Zn-Ag-Pb-Cu deposit is a stratabound massive sulphide lens occurring within Archean volcaniclastic rocks of the Yellowknife Supergroup. The deposit is located in the west-central portion of the Slave Structural Province, approximately 350 km north of Yellowknife.Initial diamond drilling at Gondor has outlined a steeply dipping, L-shaped, folded, massive sulphide body, which may be traced over a strike length of approximately 800 m, and to a depth of 350 m. True widths of up to 40 m have been intersected in the thickest part of the deposit. Preliminary estimates suggest that the deposit contains a minimum of 7.5 million tonnes grading 6% Zn, 50 g/tonne Ag and less than I% combined Cu and Pb. In addition, significant gold, grading up to 2.8 g/tonne, occurs in some parts of the deposit. The mineralization is open both down-dip and along strike.The Gondor deposit lies conformably within a predominantly east-west striking, north-facing sequence of felsic to intermediate volcaniclastic rocks. Coarse fragmental rocks are abundant in the hanging wall, whereas ash and lapilli-tuffs predominate in the footwall. The main structural feature in the area is a large-scale, steeply northeast-plunging, Z-shaped fold. The sulphide mineralization lies within the synformal portion of this fold, with the thickest part of the deposit coinciding with its hinge zone. Several episodes of faulting have also affected the local stratigraphy.The wallrocks of the Gondor deposit were hydrothermally altered prior to the onset of medium-grade regional metamorphism. A halo of altered rocks surrounds the massive sulphide lens, with no apparent difference in the degree of alteration between the hanging wall and footwall strata. The alteration zone is characterized by the addition of MgO and K20 and by the depletion of Na20 and CaO. These changes are reflected in the mineralogy of the altered wallrocks by local enrichment in chlorite, biotite, muscovite and cordierite.The mineralized zone is medium- to coarse-grained, well-banded and is composed largely of pyrite, quartz, and sphalerite with subordinate galena and chalcopyrite. Preliminary studies of metal distribution indicate that a lateral zonation is present, with lead enrichment in the central part of the deposit, and copper enrichment toward both ends. Stringer-type copper mineralization has not yet been discovered in the footwall of the Gondor deposit."

Jan 1, 1985

By J. Beland

The Rimouski-Matapedia region is along the southwestern extension of the central Siluro-Devonian synclinorium of Gaspe Peninsula. As in Gaspe about 30,000 feet of Siluro-Devonian strata rest on a "basement" of tightly folded Ordovician rocks. The central synclinorium is divided up into two northeasterly trending belts each of which is characterized by distinctive lithologies and patterns of folding. The northwestern belt is gently to moderately folded and includes lithologies which point to a stable environment. The southeastern belt on the other hand is tightly folded and the lithologies indicate a less stable environment. A marked angular unconformity separates the basement from the Siluro-Devonian cover near the north-western margin of the northwestern belt. At the southeastern margin of the southeastern belt the relationship of cover to basement has not been as-certained because of a fault. The northwestern belt has several features significant in the search for petroleum; the Silurian strata are exposed in broad open anticlines

Jan 1, 1962

By S. Joshi, E. Asselin

An electrochemical quartz crystal microbalance (EQCM) was used to study the leaching of pure gold in deaerated 1 M Na2S solution. Multiple cyclic voltammograms were measured between -0.76 and 1.242 V (SHE) at 20 mV/sec and 2 mV/sec and the frequency shift of the quartz crystal was simultaneously measured. Both the forward and reverse scans showed oxidation occurred between -0.40 to 0.20V. The frequency shift increased during both the forward and reverse scans in the potential range of -0.40 to -0.06 V indicating electrode mass decreased. Since at -0.40 to 0.20 V oxidation peaks were also observed, part of the oxidation was due to oxidation of gold. Eh-pH diagrams were constructed and showed soluble Au(I)-S(IV) species formed between -0.30 and 0.10 V (SHE). Atomic absorption spectroscopy of the test solutions and the mass change recorded by EQCM both showed about 0.015 mg of gold leached. Since the majority of the frequency shift increase corresponding to gold oxidation occurred at -0.40 to -0.06 V during multiple cyclic voltammogram measurement, the total leaching of gold could be approximated to occur at this potential interval to give a leaching rate of ca. 6.4x10-5 mg/s-cm2.

Jan 1, 2011

"The Val d'Or Division now comprises the Lucien C. Beliveau Mine and Concentrator (formerly the Pascalis, described below) and the Chimo Mine. Cambior acquired an initial 50% interest in the Chimo Mine in May 1989 and the remaining 50% in April 1990. Cambior's share of 1989 production was 2121 ounces; the company expects to net 23 750 ounces from Chimo in 1990. Pascalis MineUPDATERenamed the Lucien C. Beliveau Mine at its official inauguration in September 1989, the mine is exceeding forecasts, producing over 11 500 ounces of gold in the first half of 1990. Cambior expects 1990 production to total 34 000 ounces.IntroductionThe Pascalis Mine is located 16 miles east o f Val d'Or, Quebec, and is accessible by a three mile gravel road off highway 117 (Fig. I).The property is wholly owned by Cambior.The Pascalis gold deposit consists o f a sub-vertical diorite dyke 1000 ft long by 30 ft wide containing quartz and tourmaline veins with inclusions of pyrite and native gold . Three vein systems ca n be seen in the deposit , the most important being tensile veins oriented at a right angle to the direction of the dyke and inclined at 40 degrees. These overlapping veins vary in thickness from 4 in. to 40 in. and occur at intervals of six to ten ft. The deposit is, therefore, very difficult to evaluate; a complete evaluation would require drifts over the whole width of the dyke combined with relatively short drill holes (Fig . 2)."

Jan 1, 1990

By S. J. Prout, J. M. Lang, D. Lascelles, K. Sarinas

"There is a growing demand for ore characterization methods to support metallurgical development programs from a true geometallurgical perspective. Today, there are multiple automated mineral analysis systems on the market, many of which are based on conventional mineral liberation data. However, liberation data can be limited when assessing the floatability of a mineral to predict its recovery as it doesn’t consider the surface area available for collector absorption and bubble attachment; whereas mineral exposure measurements can. Using the First-Order Rate equation to predict the recovery versus time of variously exposed particles, a model has been developed to predict the recovery of copper sulphides at a particular grind size. This model provides the opportunity for the prediction of copper recovery and grade from multiple, small-scale samples. These predicted values can be imported into resource modeling software, and guide the domaining of geometallurgical units within the ore body. Data has been analyzed from various global copper porphyry systems and compared with actual flotation testwork.IntroductionAs part of the development of a mining project, resource estimation primarily focuses on the definition of the quantity and grade of the ore in the deposit; as the project evolves from preliminary economic assessment through to feasibility, the geological model is usually further populated with hardness and recovery data.The CIM Definition Standards (2011) identifies measured mineral resource as the part of a mineral resource for which quantity, grade or quality, densities, shape, and physical characteristics are estimated with confidence sufficient to allow the application of “modifying factors” to support detailed mine planning and final evaluation of the economic viability of the deposit as an asset. The modifying factors include, but are not restricted to, mining, processing, metallurgical, infrastructure, economic, marketing, legal, environmental, social and governmental factors.With market fluctuations, many investors in the mining industry have become more and more risk averse which has increased the demand for more reliable data to support these modifying factors. This has led to the widespread use of geometallurgy and statistical analysis to better inform the resource estimation. Geometallurgy is used to characterize ore variability and is especially useful for highly variable or strongly zoned deposits, several close deposits that will be milled together, projects requiring complex or new metallurgical approaches, brownfields or sight-of-mine exploration, expansion projects that exploit new, deeper or adjacent reserves, and projects with significant legacy drill core that are being re-evaluated due to new economic circumstances."

Jan 1, 2018

By R. D. Hossack

"The selection of a site for plant facilities is a function of several factors and has as its objective the maximization of profits, given fixed markets and sources of raw material locations. In practice there are several sites, any one of which or a combination of two or more would be suitable to meet the basic requirements of source of supply of raw material and labour and still fulfill market demands. The model used to select the optimum profit combination utilizes both computer programs and traditional financial analysis techniques. Of the three computer programs used in the mode), one is a linear program and another is a transportation simulator. Basic cost and price data are required. In examining costs, three levels are used: (a) distribution costs of raw material to the plant and finished goods to the market; (b) direct production costs at the plant, such as labour and locally supplied material; and (c) capital and overhead costs at the plant, such as construction costs, taxes, insurance, and federal and provincial cost allowances. The direct costs generally depend on the scale of operations, so that a large plant in one location may have a lower unit cost than two smaller plants. This, of course, must be balanced against distribution costs. In examining profit, it is necessary to think in terms of the price and volume of sales at each of the market locations. Given basic data and relationships, the model can be used to optimally locate production facilities or, alter-natively, optimally structure a transportation network given existing locations of plants and markets. It is dynamic to the extent that it can react to changes in volume, price and cost to optimally locate an additional plant, the expansion of existing plants, the shutting down or cutting back of plants, or the restructuring of distribution networks."

Jan 1, 1970

By William Ferguson, Claude Deveau, Wade Hazel, Stephen R. Young, Allen Lussier, Robert Copeland

"LocationSometimes known as the Bernie Lake mine, the mine is located about 180 km east-northeast of Winnipeg on the northwestern shore of Bernie Lake, close to the Nopiming Provincial Park and the Manitoba-Ontario boundary. The mine is accessed from Lac du Bonnet which is linked to the provincial road system.Brief Description of OperationTantalum Mining Corporation of Canada Ltd. operates an underground mine employing ramp access, room and pillar mining, and shaft hoisting for the production of tantalum, lithium and cesium minerals. Daily campaigned crushing of the tantalum and lithium ores supply separate concentration circuits. Tantalum recovery employs conventional gravity equipment together with recently developed centrifugal concentration methods. All tantalum concentrates go to Cabot Performance Materials for the production of tantalum chemicals and metal. Lithium minerals are recovered using heavy medium separation and silicate flotation to produce spodumene and montebrasite/amblygonite concentrates. The lithium concentrates are shipped worldwide for use in ceramics, specialty glass and mold powders. Cesium processing involves the dry grinding of pollucite as feed stock for the recently built on-site chemical plant dedicated to tl1e production of cesium formate, a high-density drilling fluid for use in the oil industry."

Jan 1, 2000

By D. S. Conochie

The world is poised for rapid growth in consumption as large, less developed economies acquire greater wealth. It might be expected that there would be a corresponding growth in waste generation, but this might not necessarily be the case. The metallurgical industry has an excellent record of process development which has allowed it to provide a high tonnage supply of low cost, high quality metals. Environmental challenges have been faced and indeed the recycling of scrap iron through the electric arc furnace has made a massive contribution to cleaning up obsolete structures and equipment of past generations. Issues in waste generation and processing still remain, and the expectation for cleaner processing and environmental performance continues to rise. The waste impact of key process developments of the last century and the recent developments in metallurgical waste processing in Canada will be outlined. The potential to use state of the art design tools to produce the next generation of zero waste processes will then be explored.

Jan 1, 2004

By Zhan Zhang, Hiromi Nagaumi, Zhen Li

"Recently, the remarkable strengthening effect of ??-Al(Mn, Fe) Si dispersoids at both ambient temperature and elevated temperature were found by several researches. A large amount of dispersoids can be formed by applying special heat treatments and within a suitable range of chemical composition of AA3xxx alloys. In the present work, the influences of Cr addition on the mechanical properties and microstructures of the Al-Mn-Mg-Si alloys were investigated. The mechanical properties at ambient and elevated temperatures were evaluated by micro-hardness and yield strength. Moreover, the microstructures in as-cast and heat-treated conditions were quantitatively analyzed by optical and electron microscopes. Results revealed that Cr also had effect on the number density and volume fraction of dispersoids. Micro-hardness and yield strength at ambient temperature increased with the increasing content of Cr, and the Cr addition increased the yield strength at elevated temperature as well. Moreover, the creep resistance at 300°C improved dramatically with the increasing content of Cr.INTRODUCTION Traditionally, AA3xxx aluminum alloys were widely used in packaging, automobile and architecture industries, because of its good formability, excellent corrosion resistance and weldability. And AA3xxx alloys were considered as non-heat-treatable alloys. However, the strengthening effect of dispersoids in AA3xxx alloys was discovered recently (Li & Arnberg, 2003;Li, Muggerud, Olsen, & Furu, 2012; Li, Zhang, & Chen, 2016; Liu & Chen, 2015).Alarge amount of dispersoids could precipitate by a proper heat treatment.In order to further improve AA3xxxalloys, the composition of the alloys should be optimized. A few previous studies were reported to investigate the influence of compositions on AA3xxx alloys. Adding Mn element could enhance the precipitation of ??-Al(Mn, Fe)Si dispersoids and improve the yield strength(Muggerud, Mørtsell, Li, & Holmestad, 2013), as long as the concentration of Mn was under the solid solution limit. Fe decreased the solubility of Mn and accelerated the precipitation rate of ??-Al(Mn, Fe)Sidispersoids(Li & Arnberg, 2003), the yield strength and creep resistance at elevated temperature could increase with an optimized content of Fe(Liu & Chen, 2016). Mg element would affect the nucleation process of ??-Al(Mn, Fe)Sidispersoids by forming metastable Mg2Si(Hirasawa, 1975; Li, Zhang, & Chen, 2017a; Lodgaard & Ryum, 2000), metastable Mg2Si precipitated during heating process and promoted the precipitation of ??-Al(Mn, Fe)Sidispersoids, moreover, Mg provided solid solution strength for AA3004 alloys(Li et al., 2016). Si increased the volume fractionof ??-Al(Mn, Fe)Sidispersoids(Muggerud et al., 2013)and decreased the size of ??-Al(Mn, Fe)Sidispersoids(Li, Zhang, & Chen, 2017b). With the addition of Mo, the size of dispersoids became finer with a higher volume fraction, the volume percentage of dispersoid free zones was reduced. Elevated temperature yield strength and creep resistance improved due to Mo addition (Liu, Ma, & Chen, 2017).However, the effect of Crelements on microstructure and mechanical properties of AA3xxx alloys were rarely reported."

Jan 1, 2018

By W. B. Morrey

This paper deals with the development of the new cap-sensitive slurry explosives. The history and special features of these explosives are outlined, and recent field trials are described.

Jan 1, 1973

By Yuyong Li, Liangman Zhang, Zhaolian Wang, Shun Wang, Ltd. Shandong Huate Magnet Technology Co., Fengliang Liu

"Introduce a newly revolutionary magnetic separator - Raising Concentrate Grade and Decreasing Dregs Content Magnetic Separator Series JCTN (i.e. RCG&DDC MS JCTN). HUATE® JCTN is designed for rinsing, purification, desliming and thickening of the magnetic minerals as per different requirements. Adopting 240°-270° larger magnetic element with multi-poles and magnetic pulsation, and combining the devices of multi-channel rinsing water and top flushing water and new style tank, HUATE® JCTN can improve another 2%-10% concentrate mFe% than the traditional MS without lowering the concentrate recovery rate. Thereby, it solves the uneasy concentrate upgradation problem of the traditional MS resulting from the magnetic aggregation. Now, JCTN has been successfully applied in more than 30 mines in Australia, China and Russia, e.g. Sino Iron of CITIC PACIFIC MINING MANAGERMENT PTY LTD. HUATE® JCTN can optimize the industrial processing line by: 1) improving the discarding rate before milling to discard the necessary tailing ASAP; 2) getting in advance the final concentrate after milling. One JCTN can replace many traditional MS in series. In some way, it can also replace the anti-flotation separation process.INTRODUCTIONWe’re writing to introduce a newly revolutionary magnetic separator - Raising Concentrate Grade and Decreasing Dregs Content Magnetic Separator Series JCTN (i.e. RCG&DDC MS JCTN). HUATE® JCTN is designed for rinsing, purification, desliming and thickening of the magnetic minerals as per different requirements."

Jan 1, 2016

By S. Deonarain, L. S. Schultz

"This paper details the process and methodology followed to rehabilitate a rectangular ventilation shaft, situated in the Free State region of the Witwatersrand Gold Fields in South Africa. The shaft consists of seven compartments where self-mining of the sidewalls had taken place and damage to the decayed steel work in the shaft had taken place, thus limiting access down the shaft. The paper will provide some insight into the successes and challenges encountered during the project and may provide some learnings for future projects of a similar nature. INTRODUCTION The ventilation shaft forms part of the Phakisa Mine, situated in the Welkom area of the Free State province of South Africa, and is located in the Southern part of the Witwatersrand Basin, one of the world’s largest known and richest gold deposits (Figure 1).As is typical in South African gold mines situated in the Witwatersrand basin, the shaft is 1 770 metres deep (below collar). The shaft was sunk during the early 1940’s and comprised a rectangular shape with 7 compartments, used for both rock hoisting and men and material winding, respectively, with a single lift “Mary-Anne” compartment. Early in 2003, the mine decided to change the shaft from a downcast hoisting shaft to an up-cast ventilation shaft. The conveyances, ropes, winders and headgear (head frame) were removed and replaced with a high volume fan delivering 323m³/s of air at a pressure of 4.2Pa on surface. The up-cast velocity in the shaft was 6.5m/s, however this reduced significantly with the scaling of the shaft and the restrictions at shaft bottom. Although Harmony had converted the shaft from a downcast service shaft to an up-cast ventilation shaft some years back, the shaft steel work in the barrel of the shaft was left intact. Over the years, the steelwork in the shaft had decayed (rust and grime) and portions of this steelwork fell down the shaft. Concurrent with the decaying steel work, portions of the shaft lining had collapsed and it was getting progressively worse."

Jan 1, 2019

By Malcolm Black

Introduction Before beginning to write this paper, I decided that I should first find suitable definitions of the words Sample and Sampling. The dictionary gives: "Sample.-A portion indicative of the whole"; and according to Baillie (1), sampling is "That process whereby a representative and comparatively small portion of material is selected from a large bulk, and preserved under such conditions as shall prevent contamination or avoidable alteration, with a view to the formation of valid conclusions regarding the suitability of the bulk for specified purposes". These comprehensive definitions are alike in substance, and indicate that unless a truly representative portion is taken, it is not a sample. Ore 'as mined' generally varies a good deal in composition, and, in crushing, segregation takes place. Some of the minerals present, due to differences in hardness and friability, break into smaller pieces than others, and, on reaching the bin, the coarse particles roll away, leaving the fines behind. The result of this segregation is generally quite noticeable on the conveyor feeding the mill, especially when the bin is nearly empty and the crushing plant shut down. Should the sampling period synchronize with either the coarse or the fines, the sample obviously would not be representative. I agree that this is rather far fetched, but I maintain that such a condition is possible. Assuming that a representative sample may be procured from the feed conveyor, the method of cutting it down for assay has considerable influence in maintaining the original condition of the sample. The finer the material is ground after each cut, the more uniform the sample will remain. To illustrate this point, let us take a quantity of fine sand and add, say, three grains of rice to represent metallic particles. We may mix this sample by any of the known methods, then cut it into four equal portions. It is obvious that at least one of the portions will be without a rice grain. But let us grind the three grains of rice into flour and proceed as before. Now there will be a much greater chance of including some of the rice in each portion.

Jan 1, 1935

By M. A. Nagle

Various strategic projects were carried out in 2002 to increase the capacity of Teck Cominco's integrated zinc-lead smelter at the Trail operations site in British Columbia, Canada. The lead smelter treats the iron residue from the zinc plant and optimizes the overall zinc recovery. This paper summarizes two options that were considered to reduce the zinc content in the leaching iron residue. The first option involved increasing the capacity of an existing hot acid leach circuit up to the iron loading constraints of the circuit. The second sought to maximize the hot acid leach capability by separating the ferrite-rich solids, followed by aggressive hot acid leaching (>100°C) and subsequent iron precipitation. Different forms of iron precipitation were reviewed in order to determine the most effective and economical approach. Among these, was a novel high temperature ferrite conversion process. The technical results and selection criteria are presented together with possible ways to integrate the process concepts into the current sulphide leaching plant circuit. The first option was selected for implementation and is currently being operated successfully.

Jan 1, 2006

By Michael T. McCaffrey

The wide range of potential feed materials, process steps, and products in metallurgical facilities means that standard equipment might not be available to adequately meet the project technical and economic needs. Custom designed equipment should be considered only after rigorous research precludes purchasing standard equipment. However, the decision to use custom equipment introduces a new element of risk into the project. To manage the risk, custom equipment design should be developed through the same front end loading (FEL) phases as project development. If more than incremental development of custom equipment is required, appropriate test work or pilot trials are required to test key uncertainties. Important activities during custom equipment design include maintaining clearly defined performance objectives, conducting appropriate reviews, carefully crafting commercial and intellectual property agreements with design and fabrication partners, and assembling a multidisciplinary team with sufficient development expertise.

Jan 1, 2015

By S. Luidold, A. Poscher, H. Antrekowitsch

"The rare earth elements (REE) are nowadays mainly used for permanent magnets, catalysts, hydrogen storage alloys in rechargeable batteries, for glasses, ceramics, and polishing agents. Other important areas of application are phosphors in different types of lamps (fluorescent tubes, energy-saving lamps, etc.). These lamps are often collected and treated at their end of life by disintegration and sorting. However, the obtained fine fractions comprise not only REE-containing phosphors but also small amounts of mercury and are therefore disposed till today in special landfills. Due to the enormous price increase of the rare earths during the last two years, a lot of activities started for extracting these elements from secondary resources such as for example phosphors. All recycling concepts for this task mainly work with hydrometallurgical methods. The large number of different compounds in phosphors with sometimes very different behaviors with respect to their solubility in aqueous phases forms a major challenge to achieve good yields as well as acceptable purities of the produced rare earth concentrates by a process with a reasonable number of operation steps. Therefore, this paper gives at first a brief overview about the compounds, used as phosphors and about existing concepts or investigations. It further describes our own process design and the results, obtained on laboratory scale. INTRODUCTIONThe rare earth elements (REE) have a central position in the industrialised world despite their marginal production volume in comparison to common metals such as aluminium, copper, zinc etc., because they are essential for many applications. They often cannot be substituted without a considerable loss on functionality and quality. This group of metals comprise the lanthanoids (f–block elements, lanthanum–lutetium) as well as scandium and yttrium.The estimated world mine production of REE amounted to 133,000 t rare earth oxide equivalent in 2010, whereat China accounted for 130,000 t or 98 % (Cordier, 2012). The European Union (EU-27) imported 23,013 t in 2008 to cover its demand. The figure 1 shows the fraction of the European member states in terms of the total imports of rare earth compounds from outside the EU-27 (Schüler, Buchert, Liu, Dittrich, & Merz, 2011)."

Jan 1, 2012

By Baochun Wang, Hongli Jia, Zhaolian Wang, Fengliang Liu

"Promote and apply a new beneficiation technology and equipment effectively processing the refractory and medium-fine grained weak-magnetic minerals. HUATE® Forced-oil Cooling Vertical Ring WHIMS adopts the transformer oil cooling technology to cool excitation coils, solving the easily generated scaling problem resulting from water cooling, thereby to eliminate the demineralized water system. With <25 temperature ?raise, its magnetic field is stable. Wrapped by outer magnetic armor, it can generate a background intensity 1360kA/m. It effects very well in 1) wet preseparating the weak-magnetic coarse grains, like hematite, manganese ore, ilmenite, and purifying the concentrate; 2) removing the ferrous impurities and purifying the non-metallic minerals, like quartz, feldspar, kaolin; 3) enriching and recovering tailings from non-ferrous metals, like copper, lead, cobalt, molybdenum, thereby to greatly improve the mine resource utilization. It has applied 14 relative patents in China, and the invention patent in 56 countries, like Russia, USA, Australia, via PCT international organization. HUATE® WHIMS has been applied and accepted in more than 100 mines in and out of China. Compared with water cooling vertical ring WHIMS, it’s energy-saving and water-saving, and avoiding generating the scale. While compared with JONES WHIMS under the same separation indexes, it’s featured of more space-effective, lighter, lower costs, higher gradient, higher efficiency, larger processing capacity and wider grain application scope. Greatly promoting development of mineral processing technologies, HUATE® WHIMS is the equipment to reduce costs and improve efficiency urgently needed by the mine enterprises now.INTRODUCTIONAt present, influenced by the price and production factors, the international market demand for the grade of iron ores is increasing continuously. Restricted by the ore occurrence state, the beneficiation technology level and product economic value, every year the stope strips the stockpiling and discards hundreds of millions of tons of waste rocks containing iron, especially the weak magnetic hematite and limonite with <20% Fe%. The utilization technological bottleneck of these waste rocks makes their concentration ratio as high as 5-6, which leads to the huge wastes of energy, materials and beneficiation reagents and the increase of production costs. The effective solution is to improve the selected Fe% of the waste rocks like hematite. With the successful application of HPGR technologies in Chinese large iron mines, the mill feeding size has been reduced to 6-0 mm or 3-0 mm from the original 15-0 mm in the crushing system with 3 stages of crushing and 1 stage of closed circuit. This creates the conditions for the wet separation and recovery. While for the medium-fine grained weak-magnetic minerals, it lacks of the effective separation and recovery equipment in the world, which’s badly in need of R&D of the medium-fine grained high gradient wet strong magnetic preseparation equipment."

Jan 1, 2016