Search Documents

By J. L. Miller, R. W. Burns

This paper sets out the various phases of bringing a merchant bar mill into operation from feasibility consideration through financing, design and scheduling to completion.

Jan 1, 1967

By R. L. Bishops

This paper discusses some of the materials, processes and systems used in motor insulation. Among the materials mentioned are epoxies, polyesters, mica paper composites and wire enamels. Two processes developed to take advantage of the special characteristics of two of these materials are described, and how these materials are used in several new insulation systems now on the market is discussed. Finally, future trends in motor insulation are outlined.

Jan 1, 1969

By Gorrell. H. A.

Subsurface water data can be very valuable in .petroleum exploration and research. For the discussion of problems related to subsurface waters uniform nomenclature and classifications are required. The term 'connate water' has frequently been incorrectly used. It should .only be used in its original sense in which it is analagous to 'fossil water'. Classifications .based on origin and on sodium-chloride content are proposed. Present and possible uses of formation water analyses are briefly discussed. Since the potential uses of formation water data are not fully understood, complete analyses of selected samples should be made to insure against future requirements. The subsurface waters of Alberta show considerable regional variation in amount and proportion of dissolved salts.

Jan 1, 1958

By Leon C. Botham

?? Review of Requirements ?? Components of Modeling ?? Water Management ?? Tailings Management ?? Primarily a water management problem ?? Solids relatively easily contained ?? Process flows and runoff a continuous stream over life of mine ?? Need to allow this to safely happen over wide range of conditions

May 1, 2008

By Sherwin F. Kelly

With the progressive exhaustion of ore deposits easily discovered by surface prospecting, the attention of scientists is being turned more and more to the employment of mechanical means for the location of ore bodies whose outcrops are not visible. The dip needle, the Eotvos Torsion balance, and various methods of electrical prospecting are illustrative of the modem tendency. Interest in the possibility of applying electricity to the solution of many of the prospector's problems dates much farther back than is usually realized. The first person to notice an abnormal intensity of electrical activity in the region of certain ore bodies was an Englishman, R. W. Fox, who experimented on the Cornwall copper and tin veins about 1830. Dr. Barus, in the United States, carried the early experiments a step further in his work on the deposits of Eureka, Nevada, about 1880. He made the very definite suggestion that the phenomena noticed would be of material aid to the prospector. Not until Professor Schlumberger, of the Ecole des Mines, Paris, took up the matter, shortly before the war, was any definite effort made to put electrical prospecting on a commercial basis. His work resulted in the establishment of sound principles and practicable field technique, for two distinct methods of prospecting.

Jan 1, 1924

By B. Wasmund, M. Parravani, M. Jastrzebski, Z. Coull

"One of the main drivers of overall profitability of pyrometallurgical vessels is refractory lining campaign life. Increased economic pressure to improve vessel life requires innovative solutions to the problem of refractory cooling. Hatch has recently developed a high-intensity, waterless cooling system that bridges the performance gap between external shell cooling and internal water-cooled copper elements. External shell cooling has a limited effectiveness in protecting the refractory lining, because it is thermally insulated from the hotface of the lining by its thickness. This situation does not improve until the lining itself has become worn near the end of the campaign. The patented technology developed by Hatch overcomes this problem by positioning high-velocity air-cooling channels within the lining, closer to the hotface where the cooling benefits can be realized throughout the entire duration of the campaign. The current paper presents the development and application of Internal Air Cooling technology as well as results from the pilot campaign in an operating commercial vessel. Various adaptations for this novel, cost-effective and inherently safe system are also discussed."

Jan 1, 2015

By Wallace R. Horn

"MR. CHAIRMAN AND GENTLEMEN :I begin this talk by making a couple of comments which are of the nature of disclaimers.Firstly, and as the Chairman has otherwise indicated, I was neither ""born into"" nor have I spent more than a few years of my professional life in the mining industry. I mention this because many might, and perhaps rightly, consider that an added qualification in presenting a report of what the industry has accomplished. Indeed, I am not here to blindly defend all of its actions and inactions in respect to environmental control over the years. Nor am I here to seek absolution of the industry's past transgressions - if indeed that is the word. Mistakes might be a better one. I concluded some time ago that the effects of those mistakes are too difficult to assess against the sea of errors of our total society. I should mention too that I am not an environmental engineer or specialist - only a portion of my interest is involved with this field. Perhaps this permits a perspective which allows a more accurate and objective view.One further comment here. My job today, as I understand it, is to generally report upon the nature and extent of the response of the metals mining industry to control of the environment. In the case of an industry operating at more than a hundred locations and for various reasons at various stages of progress, it is not an easy job. On the other hand, I wanted to avoid the use of generalities because, especially within the context of environmental or ecological opinion and of the practice of condemnation of industrial segments, I think we've had about enough of generalities until we know far more than we do.Finally, I am quite aware that a statement of future plans to achieve environmental control does not impress or satisfy as many people as it may have done some years ago. Public opinion demands to know what is currently underway, today."

Jan 1, 1972

By P. E. Cavanagh

FOR THE PAST seven years Mr. W. Simpson, Chief Mechanical Inspector for the Nova Scotia Department of Mines, has carried out exhaustive field trials of non-destructive inspection equipment in the coal mines of that Province. This work has demonstrated the usefulness of a number of types of non-destructive inspection when used for periodic inspection of hoisting and haulage equipment in the coal mines of Nova Scotia. As a result, the Dominion Coal Company has instituted a programme of regular preventive maintenance inspection ?by a special staff of qualified and trained men. The purpose of this present paper is to describe how non-destructive testing techniques are used on ropes, axles, couplings, and other hoisting and haulage equipment, how these methods are being used in other industries, and the expected benefits from intelligent and properly organized use of these techniques in the coal mining industry.

Jan 1, 1956

By T. R. C. Aston, C. M. K. Yuen, J. L. Gilby

"The access tunnels for the Donkin-Morien Mine in Cape Breton, Nova Scotia, comprise two parallel tunnels driven through a sedimentary sequence of sandstone, siltstone and mudstone to intersect the Harbour Coal Seam under the Atlantic Ocean, approximately 3.5 km offshore (Fig. 1). The No. 2 tunnel was driven a total distance of 3579 m using a 7.6 m diameter Loyat full-face tunnel boring machine (TBM) and was supported by steel sets. The No. 3 tunnel was initially driven a distance of 1027 m using drill and blast methods (dimensions 7.6 m wide by 5.3 m high) supported by rock bolts and shotcrete. This tunnel was then completed (front March 1986 to February 1987) using the tunnel boring machine to a distance of 3573 m.During the period May 1983 to December 1984, a major geotechnical research program was undertaken in the Donkin-Morien tunnels by Golder Associates in conjunction w,ith CANMET and the Cape Breton Development Corporation (Yuen et al., 1985). The research program included the monitoring of the performance of the TBM and drill and blast drivages, and the study of the thrusting characteristics and rock-interaction of the TBM excavation. The main emphasis of the research program was on the collection of field data which was to be made available in the form of a comprehensive report for the future use of others who might wish to carry out a detailed interpretation and analysis. The information gained from the program was also used during the tunnel"

Jan 1, 1988

ABSTRACT The inevitable uncertainty in modelling spatial variables decreases as more data become available. This reduction depends on the properties of the variable being modelled. Spatially continuous variables show less uncertainty for a given spacing than erratic variables. A geostatistical simulation based approach is developed to quantify the relationship between uncertainty and data spacing. Reference realizations are sampled to condition additional realizations and quantify uncertainty. The procedure is automated, making it straightforward to consider sensitivity and different geological domains. A case study of the relationship between uncertainty and data spacing for net oil sands thickness data from northern Alberta is presented. _ KEYWORDS Simulation, Sampling,

Jan 1, 2013

By R. D. Brown

"Concerns over possible additional involvement of governments in Canada's mining industry and its adverse effects on the industry 's growth were a frequent topic of conversation at the recent Annual General Meeting of the CIM.Still painfully fresh in the minds of industry leaders are the disastrous results of the federal/provincial scramble over resource revenues which followed the relatively high metal prices witnessed in 1973/1974. At current metal prices, it is not surprising, then, that a nagging fear persists that these governments may once again restructure tax and other rules to the detriment of the industry and the country.This month, Tax Notes recalls some of the progress which the industry and governments have made in 1979 in the taxation of the resource sector, and urges that higher metal prices be viewed in light of the costly exploration, development and production efforts which will be required for the industry to continue to play its important role in our economy.IntroductionAt the Annual General Meeting of The Canadian Institute of Mining and Metallurgy, held in April, 1980, it was abundantly clear that there is widespread concern in Canada's mining industry that this country's tax regime may once again be blasted by ill winds of change.A stable and more favourable tax climate, as well as higher metal prices and profits, made 1979 almost a golden year for Canadian mining. However, from the tax viewpoint at least, there are some spots on the silver lining as apprehensions grow that the well-heralded battle between federal and provincial governments over oil and gas may spread to the mining sector, with serious damage to the industry and its newfound federal-provincial cooperation."

Jan 1, 1980

By X. T. Zeng, X. Z. Ding, W. R. Chen, L. R. Zhao

The effect of deposition defects in metal nitride coatings on erosion behavior is presented. AlCrN, AlTiSiN, TiSiN and TiSiN:MoS2 coatings were fabricated by reactive cathodic arc evaporation and unbalanced magnetron sputtering processes. The microstructure and mechanical properties of the coatings were characterized by X-ray diffraction, scanning electron microscopy and nanoindentation, and the erosion property was assessed by solid particle impingement testing. The erosion characteristics on the coating surface and cross section were analyzed and correlated to the defects, which played an important role by promoting formation of erosion pits.

Jan 1, 2006

By M. B. McClenaghan

"The Matheson area of northeastern Ontario is of great interest for mineral exploration because of its geological similarities with the adjacent Timmins, Kirkland Lake and Larder Lake gold camps. Exploration in the area, however, is hampered by the presence of an extensive and thick cover of glacial sediments. For this reason, till geochemistry has become an important exploration method. The Ontario Geological Survey&apos;s Black River-Matheson (BRiM) reconnaissance till sampling project, carried out between 1984 and 1988, was designed to aid exploration in the Matheson area by documenting the Quaternary stratigraphy and providing a database of till geochemistry. Till samples were collected by backhoe trenching of surface pits in areas of thin drift (< 5 m) and by sonic overburden drilling in areas of thicker drift. This paper summarizes the results from the shallow till sampling component of the BRiM project.Two hundred and eighty-two surface samples were collected from Matheson Till, the youngest till sheet in the area, which was deposited during the Late Wisconsinan. For each sample, the non-magnetic heavy mineral (> 3.3 S.G.) and fine (- 250 mesh) till fractions were analyzed geochemically. In addition, visible gold grains were recovered by panning the heavy mineral fraction. Five areas that display multi-element anomalies in both till fractions warrant further investigation: (1) western Egan Township, overlying the Bradley Lake Syenite; (2) around and south of the Munro and Croesus mines, in Munro and Guibord townships; (3) central Garrison Township overlying the Garrison Stock; (4) south of Ore Car Lake in northern Thackeray Township; and (5) southeastern Harker Township. In these areas, Matheson Till has a local provenance and the bedrock sources for these anomalies are nearby in the up-ice (north northwest) direction. Due to the fine-grained nature of gold in bedrock deposits in the BRiM area, the small size of most gold grains recovered from till samples (< 50 um) and the variable distribution of gold in the heavy mineral concentrate and fine fractions, the fine fraction in addition to the more commonly used heavy mineral concentrate should be used for gold exploration.Surface till samples have been affected by weathering to a depth of = 3 m. Weathered till is characterized by a very low carbonate content in the matrix fraction, the absence of sulfide grains in the heavy mineral concentrate and higher concentrations of copper, nickel and zinc in the fine fraction than in the heavy mineral concentrate. As a result of the weathered/ oxidized nature of the surface till samples, the fine fraction is a better sampling medium for base metal exploration."

Jan 1, 1992

By Roberto Pena, Cristhian Morales, Darwin Morales, Veronica Cambiaso

"This article makes evident the shortcomings of the current operation of oxygen pipes as well as the damages they cause and why they cause them. When focusing on the causes and effects of these drawbacks, it was possible to develop a new family of thermal lances that could pierce a taphole with the precision of a drill but with the capacity to complete the whole operation. Although efforts have been made to replace oxygen pipes since they are annoying, dangerous and inefficient, nobody had worked to improve the way the traditional oxygen pipe taps/perforates the furnaces and reactors tapholes. In fact, developments made in drills and robotic arms, have failed to replace the oxygen pipe, which despite their negative side effects have been used for more than a century. Observation and theory were key to radically transform this humble tool into a dependable and efficient support in the operation. A good news that it is worthwhile to share for the benefit of all of us, passionate about the world of pyro metallurgy.INTRODUCTION Normally, reports and papers prepared for conventions, symposia or other technical events related to metallurgy aim to relevant topics in the operational field, probably because in them lay the scale economies every company pursues. We intend to give relevance to a matter normally disregarded in operations, but that unmistakably vital: if the furnace or reactor cannot be bled, the pyrometallurgical process will not be completed. Besides, if the tapping task is difficult or is long delayed, the availability of the furnace will be reduced. Consequently, there will be a waste of energy and workers will be exposed to dangerous levels of radiation as well as to work overload and physical injuries Apart from these basic effects, in tapping operations where oxygen pipes are used, we can see serious damages in the smelting furnace, especially in the taphole components such as refractory bricks, taphole jackets and water cooled plates. This paper intends to show that taking care of the tapping task can significantly upgrade not only to the tapping operation itself, but also the whole plant productivity."

Jan 1, 2017

By G. S. Headley

At the Sullivan Mine, recent experience with sulphide fires, locally referred to as " hot muck", has necessitated extensive modifications to pillar mining design and operating procedures. Potentially hot pillars are now being designed and mined to prevent fires. Unusual safety hazards and difficulties are encountered in working with, and adjacent. to, existing pillar fires. Operating procedures developed for these conditions have proved successful for safe and continuing production. These changes have minimized the impact of hot ore on current operations and have promise for an improved future.

Jan 1, 1977

By B. Panton, J. Carvalho, E. T. Brown

High-capacity, post-tensioned anchors have found wide-spread use in initial dam design and construction, and in the strengthening and rehabilitation of concrete dams to meet modern design and safety standards. Despite the advances that have been made in rock mechanics and rock engineering during the almost 80 years in which post-tensioned anchors have been used in dam engineering, some aspects of the rock engineering design of high-capacity rock anchors for dams have changed relatively little over the last 30 or 40 years. This applies, in particular, to the calculations usually carried out to establish the grouted embedment lengths required for deep, post-tensioned anchors. These calculations which involve a number of aleatory and epistemic uncertainties, usually make simplified assumptions about the distribution and values of rock-grout interface shear strengths, the shape of the volume of rock likely to be involved in uplift failure under the influence of a system of post-tensioned anchors, and the mechanism of that failure. The resulting designs are generally conservative. These aspects of the rock engineering design of large, post-tensioned rock anchors for dams could be improved by making greater use of modern, comprehensive, numerical analyses in conjunction with 3D models of the rock mass structure, realistic rock and rock mass properties, and the results of prototype anchor tests in the rock mass concerned.

Jan 1, 2015

By Farzad Khodabakhshi, Adrian P. Gerlich

"In this article, cold spraying process was utilized to coat the surface of AZ31 magnesium alloy with a layer of AA7075 aluminum alloy. Thereafter, friction-stir processing (FSP) was employed to enhance the microstructure and consolidate the deposited layer. The grain structure and phase morphology were studied along with indentation hardness before and after cold spraying and friction stir processing. The magnesium substrate had an initial hardness of 74 HV which increased to 102 HV after FSP due to refinement of grains to <2 µm. The aluminum coating layer, provided improved surface hardness up to 160 HV, which further increased to 173 HV after FSP was applied.INTRODUCTION Cold spray is a material deposition process which can be used for surface modification, since it deposits material on a metallic substrate with little heating by way of high velocity ballistic impacts. Using cold spray technology, it is possible to deposit a wide range of coatings with various thicknesses by controlling the characteristics of the feeding powder and metal substrate, gas temperature, gas pressure, powder feeding rate, nozzle geometry, and gun traverse velocity. This process has been recently employed for surface modification in various aircraft and automobile structural applications. This has led to a broad range of research using this process for production and modification of different metallic and non-metallic systems. In the present study, cold spray process was used to deposit a uniform layer of aluminum-zinc alloy (AA7075) on the surface of AZ31 magnesium alloy. This coating was subsequently treated by way of friction-stir processing (FSP) as a new post-spraying modification technique to enhance the structural homogeneity and densification of the coated aluminum layer. This method utilizes a non-consumable rotating tool with a specially designed shoulder and pin that is plunged into the surface of metal to be modified and then moved along the direction of interest. The localized frictional heating between the rotating tool and workpiece leads to softening of the materials around the pin, and material extrusion through a complex flow of material from the advancing toward the retreating side the tool. To the author’s best knowledge, only a few reports discuss the modification of a cold sprayed deposit by FSP process. The microstructure and mechanical properties of the cold sprayed layer and substrate before and after FSP modification were examined using optical observations (OM) and indentation hardness testing. Furthermore, the AZ31 alloy substrate alone was treated with FSP as well, for the aim of comparison to the processed coating."

Jan 1, 2017

By L. H. McKay

Tailing Dams Three types of dam have been structed to impound tailings from the Allenby mill: 1.- By classifier unit 2.- By earth dam 3.- By direct deposition of tailings The first type, which includes two dams, was built across a shallow valley which sloped down to Similkameen river, just below the mill site. Two earth embankments, one below the other, were built across the valley. Tailings were then piped to Akins classifiers mounted on wooden wheels. The classifiers were set up at one side of the valley and gradually moved ahead on the sand embankment created by the sand discharge from these classifiers, the slime overflow going to settli.ng ponds formed by the dams. Decanting wells were built in the settling ponds by placing four six-by-six timbers vertically in the ground, two feet apart, to which two-by-six tongue-and-groove boards were nailed. The elevations of the ponds were raised, as required, by nailing additional two-by-six boards on the well and bolting on more six-by-six timbers when required. The bottoms of the wells were attached to a covered launder made of three-inch lumber laid on a one per cent grade. This launder carried the overflow through the dam. The second type of dam was built across a long, narrow valley, known as Hitchen&apos;s Flat, the upper ~n d of which was about 2½ miles north of the mill. This valley, an ideal tailings site, was 4,000 feet long and from 600 to 800 feet wide. An earth embankment with a concrete spillway through the top was built approximately 28 feet high across the lower end of this valley. Tailings were then dumped into the upper end of valley, with no further expense until the basin was filled up to the level of the flume where this entered the valley. When the upper end of the valley was filled to this point there was still room for more tailings at the lower end. Therefore, a pump was installed to elevate the tailings to build a wall around the upper end of the valley by depositing sands from a launder built up on 20 foot supports and sloping both ways from the pumping station around the upper end of the basin.

Jan 1, 1950

By V. F. Hollister

Four conditions are commonly accepted as being needed for the development of native sulphur deposits in sedimentary rocks : (1) ample sulphate-bearing evaporite, normally anhydritic; (2) proximity to petroleum deposits; (3) a hydrodynamic system of communication between these two; (4) a stratigraphic or structural trap to prevent escape of the sulphur and sulphur -bearing reaction products. When any of these requisites are absent, apparently no significant residual bio-epigenetic sulphur deposit will form. These requirements are, however, satisfied in some areas, which include both the Triassic and Devonian evaporites of northeastern British Columbia.

Jan 1, 1977

By Richard K. Komarek, Antonios Zavaliangos, Roman T. Dec

Current industrial compacting and briquetting practices are largely based on trial-and¬error techniques. This paper introduces a two dimensional finite element model of compacting/briquetting process in the roller press. Compared with other modeling techniques used in the past, finite element method offers the most versatile approach because it incorporates adequate information about powder behavior, geometry and frictional conditions and offers predictions for the density distribution, velocity field, stress distribution, roll force, roll torque and other important process variables. More over, when the model includes elasticity, it offers predictions on the internal stress state in the briquet after its exit from the pressing zone. This enables to perform realistic computer experiments which are helpful for establishing the pressing system design, forming cavity geometry and process conditions necessary to produce compacted or briquetted product with the desired properties.

Jan 1, 2004